Problem reported in Red Hat bz 1040329 for strict writes where we cache
only when we hold oplock and write direct to the server when we don't.
When we receive an oplock break, we first change the oplock value for
the inode in cifsInodeInfo->oplock to indicate that we no longer hold
the oplock before we enqueue a task to flush changes to the backing
device. Once we have completed flushing the changes, we return the
oplock to the server.
There are 2 ways here where we can have data corruption
1) While we flush changes to the backing device as part of the oplock
break, we can have processes write to the file. These writes check for
the oplock, find none and attempt to write directly to the server.
These direct writes made while we are flushing from cache could be
overwritten by data being flushed from the cache causing data
corruption.
2) While a thread runs in cifs_strict_writev, the machine could receive
and process an oplock break after the thread has checked the oplock and
found that it allows us to cache and before we have made changes to the
cache. In that case, we end up with a dirty page in cache when we
shouldn't have any. This will be flushed later and will overwrite all
subsequent writes to the part of the file represented by this page.
Before making any writes to the server, we need to confirm that we are
not in the process of flushing data to the server and if we are, we
should wait until the process is complete before we attempt the write.
We should also wait for existing writes to complete before we process
an oplock break request which changes oplock values.
We add a version specific downgrade_oplock() operation to allow for
differences in the oplock values set for the different smb versions.
Cc: stable@vger.kernel.org
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
When mounting with smb2/smb3 (e.g. vers=2.1) and cifsacl mount option,
it was trying to get the mode by querying the acl over the cifs
rather than smb2 protocol. This patch makes that protocol
independent and makes cifsacl smb2 mounts return a more intuitive
operation not supported error (until we add a worker function
for smb2_get_acl).
Note that a previous patch fixed getxattr/setxattr for the CIFSACL xattr
which would unconditionally call cifs_get_acl and cifs_set_acl (even when
mounted smb2). I made those protocol independent last week (new protocol
version operations "get_acl" and "set_acl" but did not add an
smb2_get_acl and smb2_set_acl yet so those now simply return EOPNOTSUPP
which at least is better than sending cifs requests on smb2 mount)
The previous patches did not fix the one remaining case though ie
mounting with "cifsacl" when getting mode from acl would unconditionally
end up calling "cifs_get_acl_from_fid" even for smb2 - so made that protocol
independent but to make that protocol independent had to make sure that the callers
were passing the protocol independent handle structure (cifs_fid) instead
of cifs specific _u16 network file handle (ie cifs_fid instead of cifs_fid->fid)
Now mount with smb2 and cifsacl mount options will return EOPNOTSUP (instead
of timing out) and a future patch will add smb2 operations (e.g. get_smb2_acl)
to enable this.
Signed-off-by: Steve French <smfrench@gmail.com>
The get/set ACL xattr support for CIFS ACLs attempts to send old
cifs dialect protocol requests even when mounted with SMB2 or later
dialects. Sending cifs requests on an smb2 session causes problems -
the server drops the session due to the illegal request.
This patch makes CIFS ACL operations protocol specific to fix that.
Attempting to query/set CIFS ACLs for SMB2 will now return
EOPNOTSUPP (until we add worker routines for sending query
ACL requests via SMB2) instead of sending invalid (cifs)
requests.
A separate followon patch will be needed to fix cifs_acl_to_fattr
(which takes a cifs specific u16 fid so can't be abstracted
to work with SMB2 until that is changed) and will be needed
to fix mount problems when "cifsacl" is specified on mount
with e.g. vers=2.1
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Shirish Pargaonkar <spargaonkar@suse.com>
CC: Stable <stable@kernel.org>
Changeset 666753c3ef added protocol
operations for get/setxattr to avoid calling cifs operations
on smb2/smb3 mounts for xattr operations and this changeset
adds the calls to cifs specific protocol operations for xattrs
(in order to reenable cifs support for xattrs which was
temporarily disabled by the previous changeset. We do not
have SMB2/SMB3 worker function for setting xattrs yet so
this only enables it for cifs.
CCing stable since without these two small changsets (its
small coreq 666753c3ef is
also needed) calling getfattr/setfattr on smb2/smb3 mounts
causes problems.
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Shirish Pargaonkar <spargaonkar@suse.com>
CC: Stable <stable@kernel.org>
Rename CIFSSMBOpen to CIFS_open and make it take
cifs_open_parms structure as a parm.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
When using posix extensions, dfs shares in the dfs root show up as
symlinks resulting in userland tools such as 'ls' calling readlink() on
these shares. Since these are dfs shares, we end up returning -EREMOTE.
$ ls -l /mnt
ls: cannot read symbolic link /mnt/test: Object is remote
total 0
lrwxrwxrwx. 1 root root 19 Nov 6 09:47 test
With added follow_link() support for dfs shares, when using unix
extensions, we call GET_DFS_REFERRAL to obtain the DFS referral and
return the first node returned.
The dfs share in the dfs root is now displayed in the following manner.
$ ls -l /mnt
total 0
lrwxrwxrwx. 1 root root 19 Nov 6 09:47 test -> \vm140-31\test
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Unix extensions rigth now are only applicable to smb1 operations.
Move the check and subsequent unix extension call to the smb1
specific call to query_symlink() ie. cifs_query_symlink().
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Add a new protocol ops function create_mf_symlink and have
create_mf_symlink() use it.
This patchset moves the MFSymlink operations completely to the
ops structure so that we only use the right protocol versions when
querying or creating MFSymlinks.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Rename open_query_close_cifs_symlink to cifs_query_mf_symlink() to make
the name more consistent with other protocol version specific functions.
We also pass tcon as an argument to the function. This is already
available in the calling functions and we can avoid having to make an
unnecessary lookup.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Now we treat any reparse point as a symbolic link and map it to a Unix
one that is not true in a common case due to many reparse point types
supported by SMB servers.
Distinguish reparse point types into two groups:
1) that can be accessed directly through a reparse point
(junctions, deduplicated files, NFS symlinks);
2) that need to be processed manually (Windows symbolic links, DFS);
and map only Windows symbolic links to Unix ones.
Cc: <stable@vger.kernel.org>
Acked-by: Jeff Layton <jlayton@redhat.com>
Reported-and-tested-by: Joao Correia <joaomiguelcorreia@gmail.com>
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
An earlier patch allowed setting the per-file compression flag
"chattr +c filename"
on an smb2 or smb3 mount, and also allowed lsattr to return
whether a file on a cifs, or smb2/smb3 mount was compressed.
This patch extends the ability to set the per-file
compression flag to the cifs protocol, which uses a somewhat
different IOCTL mechanism than SMB2, although the payload
(the flags stored in the compression_state) are the same.
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
The multiplex identifier (MID) in the SMB header is only
ever used by the client, in conjunction with PID, to match responses
from the server. As such, the endianess of the MID is not important.
However, When tracing packet sequences on the wire, protocol analyzers
such as wireshark display MID as little endian. It is much more informative
for the on-the-wire MID sequences to match debug information emitted by the
CIFS driver. Therefore, one should write and read MID in the SMB header
assuming it is always little endian.
Observed from wireshark during the protocol negotiation
and session setup:
Multiplex ID: 256
Multiplex ID: 256
Multiplex ID: 512
Multiplex ID: 512
Multiplex ID: 768
Multiplex ID: 768
After this patch on-the-wire MID values begin at 1 and increase monotonically.
Introduce get_next_mid64() for the internal consumers that use the full 64 bit
multiplex identifier.
Introduce the helpers get_mid() and compare_mid() to make the endian
translation clear.
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Tim Gardner <timg@tpi.com>
Signed-off-by: Steve French <smfrench@gmail.com>
that prepare the code to handle different types of SMB2 leases.
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
by using a query reparse ioctl request.
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
When use of symlinks is enabled (mounting with mfsymlinks option) to
non-Samba servers, we always tried to use cifs, even when we
were mounted with SMB2 or SMB3, which causes the server to drop the
network connection.
This patch separates out the protocol specific operations for cifs from
the code which recognizes symlinks, and fixes the problem where
with SMB2 mounts we attempt cifs operations to open and read
symlinks. The next patch will add support for SMB2 for opening
and reading symlinks. Additional followon patches will address
the similar problem creating symlinks.
Signed-off-by: Steve French <smfrench@gmail.com>
Commit 9ddec56131 (cifs: move handling of signed connections into
separate function) broke signing on SMB2/3 connections. While the code
to enable signing on the connections was very similar between the two,
the bits that get set in the sec_mode are different.
Declare a couple of new smb_version_values fields and set them
appropriately for SMB1 and SMB2/3. Then change cifs_enable_signing to
use those instead.
Reported-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Currently, we determine this according to flags in the sec_mode, flags
in the global_secflags and via other methods. That makes the semantics
very hard to follow and there are corner cases where we don't handle
this correctly.
Add a new bool to the TCP_Server_Info that acts as a simple flag to tell
us whether signing is enabled on this connection or not, and fix up the
places that need to determine this to use that flag.
This is a bit weird for the SMB2 case, where signing is per-session.
SMB2 needs work in this area already though. The existing SMB2 code has
similar logic to what we're using here, so there should be no real
change in behavior. These changes should make it easier to implement
per-session signing in the future though.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
This field is completely unused:
CIFS_SES_W9X is completely unused. CIFS_SES_LANMAN and CIFS_SES_OS2
are set but never checked. CIFS_SES_NT4 is checked, but never set.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <sfrench@us.ibm.com>
If sending a call to the server fails for some reason (for instance, the
sending thread caught a signal), then we must readjust the sequence
number downward again or the next send will have it too high.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Steve French <smfrench@gmail.com>
It's not obvious from reading the macro names that these macros
are for debugging. Convert the names to a single more typical
kernel style cifs_dbg macro.
cERROR(1, ...) -> cifs_dbg(VFS, ...)
cFYI(1, ...) -> cifs_dbg(FYI, ...)
cFYI(DBG2, ...) -> cifs_dbg(NOISY, ...)
Move the terminating format newline from the macro to the call site.
Add CONFIG_CIFS_DEBUG function cifs_vfs_err to emit the
"CIFS VFS: " prefix for VFS messages.
Size is reduced ~ 1% when CONFIG_CIFS_DEBUG is set (default y)
$ size fs/cifs/cifs.ko*
text data bss dec hex filename
265245 2525 132 267902 4167e fs/cifs/cifs.ko.new
268359 2525 132 271016 422a8 fs/cifs/cifs.ko.old
Other miscellaneous changes around these conversions:
o Miscellaneous typo fixes
o Add terminating \n's to almost all formats and remove them
from the macros to be more kernel style like. A few formats
previously had defective \n's
o Remove unnecessary OOM messages as kmalloc() calls dump_stack
o Coalesce formats to make grep easier,
added missing spaces when coalescing formats
o Use %s, __func__ instead of embedded function name
o Removed unnecessary "cifs: " prefixes
o Convert kzalloc with multiply to kcalloc
o Remove unused cifswarn macro
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
If we have mandatory byte-range locks on a file we can't cache reads
because pagereading may have conflicts with these locks on the server.
That's why we should allow level2 oplocks for files without mandatory
locks only.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
When a call goes out, the signing code adjusts the sequence number
upward by two to account for the request and the response. An NT_CANCEL
however doesn't get a response of its own, it just hurries the server
along to get it to respond to the original request more quickly.
Therefore, we must adjust the sequence number back down by one after
signing a NT_CANCEL request.
Cc: <stable@vger.kernel.org>
Reported-by: Tim Perry <tdparmor-sambabugs@yahoo.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
because the is no difference here. This also adds support of prefixpath
mount option for SMB2.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Commit 6bdf6dbd66 caused a regression
in setattr codepath that leads to files with wrong attributes.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Rebased and resending the patch.
Path based queries can fail for lack of access, especially during lookup
during open.
open itself would actually succeed becasue of back up intent bit
but queries (either path or file handle based) do not have a means to
specifiy backup intent bit.
So query the file info during lookup using
trans2 / findfirst / file_id_full_dir_info
to obtain file info as well as file_id/inode value.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Acked-by: Jeff Layton <jlayton@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Now that we aren't abusing the kmap address space, there's no need for
this lock or to impose a limit on the rsize.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Now that we're not kmapping so much at once, there's no need to cap
the wsize at the amount that can be simultaneously kmapped.
Reviewed-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Steve French <smfrench@gmail.com>
and make cifs_get_file_info(_unix) calls static.
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
This is help us to extend the code for future protocols that can use
another fid mechanism (as SMB2 that has it divided into two parts:
persistent and violatile).
Also rename variables and refactor the code around the changes.
Reviewed-by: Jeff Layton <jlayton@samba.org>
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Sachin Prabhu