Remove ah->config.spurmode and ah->config.spurchans, always use EEPROM
data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX99 support enables Specific Absorption Rate (SAR) testing.
SAR is the unit of measurement for the amount of radio frequency(RF)
absorbed by the body when using a wireless device. The RF
exposure limits used are expressed in the terms of SAR, which is a
measure of the electric and magnetic field strength and power density
for transmitters operating at frequencies from 300 kHz to 100 GHz.
Regulatory bodies around the world require that wireless device
be evaluated to meet the RF exposure limits set forth in the
governmental SAR regulations.
In the examples below, for more bit rate options see the iw TX bitrate
setting documentation:
http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates
Example usage:
iw phy phy0 interface add moni0 type monitor
ip link set dev moni0 up
iw dev moni0 set channel 36 HT40+
iw set bitrates mcs-5 4
echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power
echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rather than using the chip ID to read only chain-0 CCA
registers and avoid reading chain-1, use the RX chainmask
instead. There are some 1-stream PCI devices based on AR9287
such as TL-WN751ND. Improper NF calibration might result in
DMA errors/timeouts.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that CONFIG_ATH9K_BTCOEX_SUPPORT is used for
the WLAN/BT RX diversity hooks.
Reported by the kernel build testing backend.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MC_GAIN_CTL/CCK_DETECT registers have to be programmed
with the correct configuration values if WLAN/BT RX diversity
is enabled. Add this and also take care of the BTCOEX mode
when fast diversity is enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a copy+paste error in ar9002 for the endless spectral mode,
fix that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds the spectral scan feature for ath9k. AR92xx and AR93xx chips
are supported for now. The spectral scan is triggered by configuring
a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
echo chanscan > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
iw dev wlan0 scan
cat /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan0 > samples
echo disable > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
This feature is still experimental.
The special "chanscan" mode is used to perform spectral scan while
mac80211 is scanning for channels. To allow this,
sw_scan_start/complete() ops have been added.
The patch contains code snippets and information from Zefir Kurtisi and
information provided by Adrian Chadd and Felix Fietkau.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_AN_SYNTH9 is in the analog shift register range and thus needs to be
written using the ath9k_hw_analog_shift_rmw function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the proper masks for the register instead.
Fixes adding the (still unused) half/quarter PLL flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 belongs to diversity group 0 and AR9485 belongs to diversity
group 2. Based on the diversity group we configure certain antenna
diversity paramaters such as lna1_lna2_delta and fast diversity
bias values. For AR9485 we have some gain table parameter which
selects the gain table 0/1 for main and alternate antenna
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this is necessary to support Antenna diversity and combining in new chip
sets such as AR9485, previously Antenna diversity support is available
only in AR9285
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the AR9002, the spur frequency read from the EEPROM is mangled
before being compared against AR_NO_SPUR. This results in the driver
trying to set up the spur mitigation for bogus spurs, rather than
cleanly breaking out.
Signed-off-by: Brian Prodoehl <bprodoehl@nomadio.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after
REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that
makes keeping those ops separate rather pointless, as it only increases
code size and line number counts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the hardware is configured in HT20 mode, noise floor readings for
the extension channel often return invalid values, which keep the
values in the NF history buffer at the hardware-specific maximum limit.
Fix this by discarding the extension channel values when in HT20 mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Combine multiple checks that were supposed to check for the same
conditions, but didn't. Always enable fast PLL clock on AR9280 2.0
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds macros at certain places
which could be optimized for multiple register writes.
The performance of ath9k_htc improves considerably,
especially reducing the latency involved in a scan run.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PLL control computation used to program the AR_RTC_PLL_CONTROL
register varies between our harware so just add a private callback for it.
AR9003 will use its own callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PHY split is easier done in a few steps. First move
the RF ops to the private ops and rename them accordingly.
We split PHY stuff up first for the AR5008 and AR9002
families. There are some callbacks that AR9002 share
with the AR5008 familiy so we set those first, if AR9002
has some different callbacks it will override them upon
hardware init.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau