Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114996 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sym_int_sir() in sym_hipd.c does not check the command pointer for NULL before
using it in debug message prints.
Suggested-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Acked-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variables scriptb0 and dp_sgmin are being assigned but are never used
hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'scriptb0' set but not used [-Wunused-but-set-variable]
warning: variable 'dp_sgmin' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some drivers are ADDing the scsi command's result bytes instead of ORing
them.
While this can produce correct results it has unexpected side effects.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some functions definitions have either the initial open brace and/or
the closing brace outside of column 1.
Move those braces to column 1.
This allows various function analyzers like gnu complexity to work
properly for these modified functions.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We wanted to exit the loop with "div" set to zero, but instead, if we
don't hit the break then "div" is -1 when we finish the loop. It leads
to an array underflow a few lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
memset32() can be used to initialise these three arrays. Minor code
footprint reduction.
Link: http://lkml.kernel.org/r/20170720184539.31609-8-willy@infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: David Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On parisc I see this UBSAN warning with a sym53c896:
UBSAN: Undefined behaviour in ./drivers/scsi/sym53c8xx_2/sym_hipd.c:762:24
index -1903078336 is out of range for type 'u32 [7]'
Avoid this warning by switching to div64_ul().
[mkp: fix typo]
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is only one waiter for the completion, therefore there is no need
to use complete_all(). Let's make that clear by using complete() instead
of complete_all().
The usage pattern of the completion is:
waiter context waker context
sym_eh_handler()
struct completion eh_done
init_completion(eh_done)
pci_channel_offline()
wait_for_completion_timeout(eh_done)
sym2_io_resume()
complete(eh_done)
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.
When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.
This function aborts them with DID_SOFT_ERROR.
If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.
The result is that disk returning QUEUE FULL causes request failures.
The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags. The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags. The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sym53c8xx_slave_destroy unconditionally assumes that sym53c8xx_slave_alloc has
succesesfully allocated a sym_lcb. This can lead to a NULL pointer dereference
(exposed by commit 4e6c82b).
Signed-off-by: Stratos Psomadakis <psomas@gentoo.org>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GCC warns about empty printf format strings, and after
the addition of %pV these existing such cases in the
scsi driver layer were exposed enough for the compiler
to start seeing them.
Based almost entirely upon a patch by Joe Perches.
[jejb: fix up sym53c8xx msg]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To avoid a collision with the newly-added kernel-wide skip_spaces().
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes a huge difference when you have a serial console on bootup to limit
these messages to a sane number.
Signed-off-by: John Stoffel <john@stoffel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make the sym53c8xx_2 driver slave_alloc/destroy less unsafe. References
to the destroyed LCB are cleared from the target structure (instead of
leaving a dangling pointer), and when the last LCB for the target is
destroyed the reference to the upper layer target data is cleared. The
host lock is used to prevent a race with the interrupt handler. Also
user commands are prevented for targets with all LCBs destroyed.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(Resent with proper formatting)
Fix for the sym53c8xx_2 driver to initialize lun's to_clear flag after
a bus reset (a failed clear can trigger a bus reset and it should not
be attemped again after that).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sym53c8xx prints a negotiation message after every check condition.
This can add up to a lot of messages for removable-medium devices
(CD-ROM, tape drives, etc.) that are being polled, since they return
check condition when no medium is present. This patch suppresses the
negotiation message if it would be the same as the last one printed.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sym53c8xx uses a command queue depth of 2 for untagged devices,
without good reason. This _mostly_ seems to work ok, but it has
caused me some subtle problems. For example, I have an application
where one thread sends write commands to a tape drive, and another
thread sends log sense polling commands. With a queue depth of
2, the polling commands end up being starved for long periods of
time while multiple write commands are serviced (this may also be
related to the fact the the sg driver queues commands in LIFO order).
This problem is fixed by changing the queue depth to 1 for untagged
devices. I have tested this change extensively with many different
tape drives, medium changers, and disk drives (disk drives of course
use tagged commands and are therefore unaffected by this patch).
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sym_init_device() doesn't check if pci_iomap() fails. It also tries
to map device RAM without first checking FE_RAM.
1) Move some initialization from sym_init_device() to the top of
sym2_probe().
2) Rename sym_init_device() to sym_iomap_device().
3) Call sym_iomap_device() after sym_check_supported() instead of
before so that device->chip.features will be set.
4) Check FE_RAM in sym_iomap_device() before mapping RAM.
5) If sym_iomap_device() cannot map registers, then abort.
6) If sym_iomap_device() cannot map RAM, then fall back to not using
RAM and continue.
7) Remove the check for FE_RAM in sym_attach() since dev->ram_base
is now always set correctly.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During sym2_probe(), sym_init_device() does pci_iomap(), but there is
no corresponding pci_iounmap() if an error occurs before sym_attach()
copies sym_device::s.{ioaddr,ramaddr} to np.
1) Add the sym_iounmap_device() function.
2) Call sym_iounmap_device() if an error occurs between
sym_init_device() and the time sym_attach() allocates np.
3) Make sym_attach() copy sym_device::s.{ioaddr,ramaddr} to np before
calling any function that can fail so that sym_free_resources()
will do the unmap instead of sym_iounmap_device().
Also fixed by this patch:
During sym2_probe(), if sym_check_raid() returns nonzero, then
pci_release_regions() is never called.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If sym_attach() gets an error at or before request_irq(), then
sym_free_resources() will call free_irq() for an unregistered
interrupt handler.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If sym_attach() fails to allocate np, the error path will dereference
a NULL pointer for printk.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes two bugs:
1) rmmod sym53c8xx uses shost after freeing it with
scsi_put_host(shost).
2) insmod sym53c8xx doesn't call scsi_put_host(shost) if
scsi_add_host() fails, causing a memory leak on the error path.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(The patch updated based on testing and comments from Tony Battersby.)
Change the sym53c8xx_2 driver negotiation logic so that the driver will
tolerate better device removals. Negotiation message(s) will be sent
with every INQUIRY and REQUEST SENSE command, and whenever there is a
change in goals or when the device reports check condition.
The patch was made specifically to address the case where you hotswap
the disk using remove-single-device/add-single-device commands through
/proc/scsi/scsi. Without the patch the driver keeps using old transfer
parameters even though the target is reset and reports check condition,
so the data transfer of the very first INQUIRY will fail.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch frees the luntbl dma area in sym_hcb_free if allocated.
Since the luntbl is part of a larger dma coherent area not freeing the
luntbl kept a 64k dma coherent area previous allocated through
dma_alloc_coherent allocated. This prevented a DLPAR remove IO
operation from completing successfully.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Thomas Gleixner