Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Validation of the IRQ type was added to spmi pmic-arb, however spmi-mpp
in device tree still uses IRQ_TYPE_NONE. This commit caused the
spmi-mpp probe to fail since platform_irq_count() would return 0.
Correct this by backing out the previous patch.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Fixes: 135ef21ab0 ("spmi: pmic-arb: validate type when mapping IRQ")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that spmi-gpio is a proper hierarchical IRQ chip, and all in-tree
users of device tree have been updated, we can now drop the hack that
was introduced to disassociate the old Linux virq if a hwirq mapping
already exists. That patch was introduced to not break git bisect for
any existing boards.
Driver was tested using gpio-keys and iadc/vadc on the LG Nexus 5
(hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
qpnpint_irq_domain_map did not validate the IRQ type and this can cause
IRQs to not work as expected if an unsupported type (such as
IRQ_TYPE_NONE) is passed in. Now that spmi-gpio is a hierarchical IRQ
controller, and all device tree bindings have been updated, add
additional validation to the type field.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check to see if the hwirq is already associated with another virq on
this IRQ domain. If so, then disassociate it before associating the
hwirq with the new virq.
This is a temporary hack that is needed in order to not break git
bisect for existing boards. The next patch in this series converts
spmi-gpio to be a hierarchical IRQ chip, then there are several patches
to update all of the device tree files, and finally this patch will be
reverted within the same patch series.
IRQs for spmi-gpio are all initially setup without an IRQ hierarchy
on pmic-arb when mfd/qcom-spmi-pmic.c is probed (via the
devm_of_platform_populate call) due to the interrupts property in
device tree. Once spmi-gpio is converted to be a hierarchical IRQ chip
in the next patch, existing users of gpio[d]_to_irq() will call
pmic_gpio_to_irq(), and that will use the new IRQ chip code in
spmi-gpio that sets up the IRQ in an IRQ hierarchy. The hwirq is now
associated with two Linux virqs and interrupts will not work as
expected. This patch corrects that issue.
Driver was tested using gpio-keys and iadc/vadc on the LG Nexus 5
(hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the spmi-pmic-arb IRQ code to use the version 2 IRQ interface
in order to support hierarchical IRQ chips. This is necessary so that
spmi-gpio can be setup as a hierarchical IRQ chip with pmic-arb as the
parent. IRQ chips in device tree should be usable from the start without
the consumer having to make an additional call to gpio[d]_to_irq() to
get the proper IRQ on the parent.
The old qpnpint_irq_domain_map function would hardcode the handler as
handle_level_irq, however qpnpint_irq_set_type would later override the
handler. Properly set the handler when the IRQ is mapped. This new code
doesn't return an error for IRQ_TYPE_NONE and preserves the existing
behavior of using handle_level_irq since there are some broken device
tree bindings that need to be corrected first.
Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check the irq ownership in the irq_request_resources callback
instead of checking it during the irq mapping. This can prevent
installing the flow handler for the interrupt that is not owned by the EE
and allow the irq translation during the gpio driver probe.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Tested-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The opc parameter in pmic_arb_write_cmd() function is defined with type
u8 and it's always greater than or equal to 0. Checking that it's not
less than 0 is redundant and it can cause a forbidden warning during
compilation. Remove the check.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for version 5 of the SPMI PMIC arbiter. It utilizes
different offsets for registers than those found on version 3.
Also, the procedure to determine if writing and IRQ access is
allowed for a given PPID changes for version 5.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If "core" memory resource is not specified, then the driver could
end up dereferencing a null pointer. Fix this issue.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the pmic_arb version ops to return an __iomem pointer
to the address instead of an offset. That way we do not need to
care about the base address changes in the new HW version.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver sets the pmic arbiter core interrupt as wakeup capable
irrespective of the child irqs which causes the system to wakeup
unnecessarily. To fix this, set the core interrupt as wakeup capable
only if any of the child irqs request for it. Do this by marking it as
wakeup capable in the irq_set_wake callback.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning the output value from a function, when it is possible, is the
better and cleaner way than passing it by the pointer. Hence, modify
the ppid_to_apid mapping function to return apid instead of passing
it by a pointer. While at it, pass the ppid as function parameter to
ppid_to_apid mapping function instead of passing the sid and addr.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the writel_relaxed with __raw_writel to avoid byte swapping
in pmic_arb_write_data() function. That way the code is independent
of the CPU endianness.
Fixes: 111a10bf3e ("spmi: pmic-arb: rename spmi_pmic_arb_dev to
spmi_pmic_arb")
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate the correct memory size (max_pmic_peripherals) for the
mapping_table that holds the apid to ppid mapping. Also use a local
variable for mapping_table for better alignment of the code.
Fixes: 987a9f128b ("spmi: pmic-arb: Support more than 128 peripherals")
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Optimize the qpnpint_irq_set_type() by using a local variable
to hold the handler type. Also clean up other variable usage.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the pmic_arb_find_apid() by using the local
variables to improve the code readability.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleans up the following.
- Rename the "pa" to "pmic_arb".
- Rename the spmi_pmic_arb *dev to spmi_pmic_arb *pmic_arb.
- Rename the pa_{read,write}_data() functions to
pmic_arb_{read,write}_data().
- Rename channel to APID.
- Rename the HWIRQ_*() macros to hwirq_to_*().
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The access mode checks for peripheral ownership for read/write
permissions should not be required. Every peripheral enabled for
this master is expected to have a read/write permissions. If there
is any such invalid access due to wrong configuration in boot loader
or device tree files, then it should be fixed in those locations.
Hence, remove the access mode checks from the driver.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 7f1d4e58da ("spmi: pmic-arb: optimize table
lookups") we always need the ppid_to_apid table regardless of the
version of pmic arbiter we have. Otherwise, we will try to deref
the array when we don't allocate it on v2 hardware like the
msm8974 SoCs.
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Cc: Kiran Gunda <kgunda@codeaurora.org>
Fixes: 7f1d4e58da ("spmi: pmic-arb: optimize table lookups")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the SPMI interrupt will not wake the device. Enable this
interrupt as a wakeup source.
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PMIC bus arbiter v3 supports 512 SPMI peripherals. Add the v3 operators to
support this new arbiter version.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently invokes the apid handler (periph_handler())
once it sees that the summary status bit for that apid is set.
However the hardware is designed to set that bit even if the apid
interrupts are disabled. The driver should check whether the apid
is indeed enabled before calling the apid handler.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code uses handle_level_irq flow handler even if the
trigger type of the interrupt is edge. This can lead to missing
of an edge transition that happens when the interrupt is being
handled. The level flow handler masks the interrupt while it is
being handled, so if an edge transition happens at that time,
that edge is lost.
Use an edge flow handler for edge type interrupts which ensures
that the interrupt stays enabled while being handled - at least
until it triggers at which point the flow handler sets the
IRQF_PENDING flag and only then masks the interrupt. That
IRQF_PENDING state indicates an edge transition happened while
the interrupt was being handled and the handler is called again.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PMIC interrupts each have an internal latched status bit which is
not visible from any register. This status bit is set as soon as
the conditions specified in the interrupt type and polarity
registers are met even if the interrupt is not enabled. When it
is set, nothing else changes within the PMIC and no interrupt
notification packets are sent. If the internal latched status
bit is set when an interrupt is enabled, then the value is
immediately propagated into the interrupt latched status register
and an interrupt notification packet is sent out from the PMIC
over SPMI.
This PMIC hardware behavior can lead to a situation where the
handler for a level triggered interrupt is called immediately
after enable_irq() is called even though the interrupt physically
triggered while it was disabled within the genirq framework.
This situation takes place if the the interrupt fires twice after
calling disable_irq(). The first time it fires, the level flow
handler will mask and disregard it. Unfortunately, the second
time it fires, the internal latched status bit is set within the
PMIC and no further notification is received. When enable_irq()
is called later, the interrupt is unmasked (enabled in the PMIC)
which results in the PMIC immediately sending an interrupt
notification packet out over SPMI. This breaks the semantics
of level triggered interrupts within the genirq framework since
they should be completely ignored while disabled.
The PMIC internal latched status behavior also affects how
interrupts are treated during suspend. While entering suspend,
all interrupts not specified as wakeup mode are masked. Upon
resume, these interrupts are unmasked. Thus if any of the
non-wakeup PMIC interrupts fired while the system was suspended,
then the PMIC will send interrupt notification packets out via
SPMI as soon as they are unmasked during resume. This behavior
violates genirq semantics as well since non-wakeup interrupts
should be completely ignored during suspend.
Modify the qpnpint_irq_unmask() function so that the interrupt
latched status clear register is written immediately before the
interrupt enable register. This clears the internal latched
status bit of the interrupt so that it cannot trigger spuriously
immediately upon being enabled.
Also, while resuming an irq, an unmask could be called even if it
was not previously masked. So, before writing these registers,
check if the interrupt is already enabled within the PMIC. If it
is, then no further register writes are required. This
condition check ensures that a valid latched status register bit
is not cleared until it is properly handled.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq_enable is called when the device resumes. Note that the
irq_enable is called regardless of whether the interrupt was
marked enabled/disabled in the descriptor or whether it was
masked/unmasked at the controller while resuming.
The current driver unconditionally clears the interrupt in its
irq_enable callback. This is dangerous as any interrupts that
happen right before the resume could be missed.
Remove the irq_enable callback and use mask/unmask instead.
Also remove struct pmic_arb_irq_spec as it serves no real purpose.
It is used only in the translate function and the code is much
cleaner without it.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We see a unmapped irqs trigger right around bootup. This could
likely be because the bootloader exited leaving the interrupts
in an unknown or unhandled state. Ack and mask the interrupt
if one is found. A request_irq later will unmask it and also
setup proper mapping structures.
Also the current driver ensures that no read/write transaction
is in progress while it makes changes to the interrupt regions.
This is not necessary because read/writes over spmi and arbiter
interrupt control are independent operations. Hence, remove the
synchronized accesses to interrupt region.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver uses a mix of radix tree and a fwd lookup
table to translate between apid and ppid. It is buggy and confusing.
Instead simply use a radix tree for v1 hardware and use the
forward lookup table for v2.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently uses "apid" and "chan" to mean apid. Remove
the use of chan and use only apid.
On a SPMI bus there is allocation to manage up to 4K peripherals.
However, in practice only few peripherals are instantiated
and only few among the instantiated ones actually interrupt.
APID is CPU's way of keeping track of peripherals that could interrupt.
There is a table that maps the 256 interrupting peripherals to
a number between 0 and 255. This number is called APID. Information about
that interrupting peripheral is stored in registers offset by its
corresponding apid.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usually *_dev best used for structures that embed a struct device in
them. spmi_pmic_arb_dev doesn't embed one. It is simply a driver data
structure. Use an appropriate name for it.
Also there are many places in the driver that left shift the bit to
generate a bit mask. Replace it with the BIT() macro.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system crashes due to bad access when reading from an non configured
peripheral and when writing to peripheral which is not owned by current
ee. This patch verifies ownership to avoid crashing on
write.
For reads, since the forward mapping table, data_channel->ppid, is
towards the end of the block, we use the core size to figure the
max number of ppids supported. The table starts at an offset of 0x800
within the block, so size - 0x800 will give us the area used by the
table. Since each table is 4 bytes long (core_size - 0x800) / 4 will
gives us the number of data_channel supported.
This new protection is functional on hw v2.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the test 'if (channel > 5)' is true, then we will return 'err' which
is known to be 0 at this point.
Return -EINVAL instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for more than 128 peripherals by taking a lazy
caching approach to the mapping tables. Instead of reading and
caching the tables at boot given some fixed size, read them and
cache them on an as needed basis. We still assume a max size of
512 peripherals, trading off some space for simplicity.
Based on a patch by Gilad Avidov <gavidov@codeaurora.org> and
Sagar Dharia <sdharia@codeaurora.org>.
Cc: Gilad Avidov <gavidov@codeaurora.org>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big char/misc driver update for 4.4-rc1. Lots of different
driver and subsystem updates, hwtracing being the largest with the
addition of some new platforms that are now supported. Full details in
the shortlog.
All of these have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6d/oACgkQMUfUDdst+yl93ACcCf91y+ufwU3cmcnq5LpwHPfx
VbkAn08Cn6Wu6IcihoEpR4hqGgIOtjqW
=1a3d
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.4-rc1. Lots of
different driver and subsystem updates, hwtracing being the largest
with the addition of some new platforms that are now supported. Full
details in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (181 commits)
fpga: socfpga: Fix check of return value of devm_request_irq
lkdtm: fix ACCESS_USERSPACE test
mcb: Destroy IDA on module unload
mcb: Do not return zero on error path in mcb_pci_probe()
mei: bus: set the device name before running fixup
mei: bus: use correct lock ordering
mei: Fix debugfs filename in error output
char: ipmi: ipmi_ssif: Replace timeval with timespec64
fpga: zynq-fpga: Fix issue with drvdata being overwritten.
fpga manager: remove unnecessary null pointer checks
fpga manager: ensure lifetime with of_fpga_mgr_get
fpga: zynq-fpga: Change fw format to handle bin instead of bit.
fpga: zynq-fpga: Fix unbalanced clock handling
misc: sram: partition base address belongs to __iomem space
coresight: etm3x: adding documentation for sysFS's cpu interface
vme: 8-bit status/id takes 256 values, not 255
fpga manager: Adding FPGA Manager support for Xilinx Zynq 7000
ARM: zynq: dt: Updated devicetree for Zynq 7000 platform.
ARM: dt: fpga: Added binding docs for Xilinx Zynq FPGA manager.
ver_linux: proc/modules, limit text processing to 'sed'
...
The struct irq_domain contains a "struct device_node *" field
(of_node) that is almost the only link between the irqdomain
and the device tree infrastructure.
In order to prepare for the removal of that field, convert all
users to use irq_domain_get_of_node() instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We don't want to swap bytes that we're reading and writing to the
FIFOs when we're running on a big-endian CPU. Doing so causes
problems like where the qcom-spmi-iadc driver can't detect the
type of device because the bytes are all mixed up. Use the raw IO
accessors for these API instead, and collapse pmic_arb_base_read()
into the byte reading API so that we aren't tempted to read non-FIFO
data like commands with that function.
Cc: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: http://lkml.kernel.org/r/20150713151750.915477120@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Link: http://lkml.kernel.org/r/20150713151750.831790045@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Qualcomm PMIC Arbiter version-2 changes from version-1 are:
- Some different register offsets.
- New channel register space, one per PMIC peripheral (ppid).
All tx traffic uses these channels.
- New observer register space. All rx trafic uses this space.
- Different command format for spmi command registers.
Reviewed-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm PMIC Arbiter, in addition to being a basic SPMI controller,
also implements interrupt handling for slave devices. Note, this is
outside the scope of SPMI, as SPMI leaves interrupt handling completely
unspecified.
Extend the driver to provide a irq_chip implementation and chained irq
handling which allows for these interrupts to be used.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qualcomm's PMIC Arbiter SPMI controller functions as a bus master and
is used to communication with one or more PMIC (slave) devices on the
SPMI bus. The PMIC Arbiter is actually a hardware wrapper around the
SPMI controller that provides concurrent and autonomous PMIC access
to various entities that need to communicate with the PMIC.
The SPMI controller hardware handles all of the SPMI bus activity (bus
arbitration, sequence start condition, transmission of frames, etc).
This software driver uses the PMIC Arbiter register interface to
initiate command sequences on the SPMI bus. The status register is
read to determine when the command sequence has completed and whether
or not it completed successfully.
Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner