Convert to new probing mechanism and add hotplug support by enabling
PORT_IRQ_PHYRDY_CHG, marking ehi for hotplug and scheduling EH on
PORT_IRQ_PHYRDY_CHG or PORT_IRQ_DEV_XCHG.
Sil3124/32 family of controllers don't have any mechanism to wait for
the first D2H FIS after hotplug, so ATA_FLAG_SKIP_D2H_BSY is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Use phy debouncing instead of unconditional wait after DEV_RST and
make sil24_hardreset() to request followup SRST as that's the only way
to wait for !BSY. Note that the original implementation never worked
- if the cached status was !BSY, ata_busy_sleep() finished
immediately; otherwise, it timed out regardless of the actual device
status.
Signed-off-by: Tejun Heo <htejun@gmail.com>
PORT_PRB is a misnomer as the area also contains other stuff. Rename
it to PORT_LRAM and add PORT_LRAM_SLOT_SZ.
Signed-off-by: Tejun Heo <htejun@gmail.com>
With hotplug, every reset might be a probing reset and thus something
similar to probe_init() is needed. prereset() method is called before
a series of resets to a port and is the counterpart of postreset().
prereset() can tell EH to use different type of reset or skip reset by
modifying ehc->i.action.
This patch also implements ata_std_prereset(). Most controllers
should be able to use this function directly or with some wrapping.
After hotplug, different controllers need different actions to resume
the PHY and detect the newly attached device. Controllers can be
categorized as follows.
* Controllers which can wait for the first D2H FIS after hotplug.
Note that if the waiting is implemented by polling TF status, there
needs to be a way to set BSY on PHY status change. It can be
implemented by hardware or with the help of the driver.
* Controllers which can wait for the first D2H FIS after sending
COMRESET. These controllers need to issue COMRESET to wait for the
first FIS. Note that the received D2H FIS could be the first D2H
FIS after POR (power-on-reset) or D2H FIS in response to the
COMRESET. Some controllers use COMRESET as TF status
synchronization point and clear TF automatically (sata_sil).
* Controllers which cannot wait for the first D2H FIS reliably.
Blindly issuing SRST to spinning-up device often results in command
issue failure or timeout, causing extended delay. For these
controllers, ata_std_prereset() explicitly waits ATA_SPINUP_WAIT
(currently 8s) to give newly attached device time to spin up, then
issues reset. Note that failing to getting ready in ATA_SPINUP_WAIT
is not critical. libata will retry. So, the timeout needs to be
long enough to spin up most devices.
LLDDs can tell ata_std_prereset() which of above action is needed with
ATA_FLAG_HRST_TO_RESUME and ATA_FLAG_SKIP_D2H_BSY flags. These flags
are PHY-specific property and will be moved to ata_link later.
While at it, this patch unifies function typedef's such that they all
have named arguments.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement NCQ support. Sil24 has 31 command slots and all of them are
used for NCQ command queueing. libata guarantees that no other
command is in progress when it issues an internal command, so always
use tag 0 for internal commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert sata_sil24 to new EH.
* When port is frozen, IRQ for the port is masked.
* sil24_softreset() doesn't need to mangle with IRQ mask anymore.
libata ensures that the port is frozen during reset.
* Only turn on interrupts which are handled by interrupt handler and
EH. As we don't handle SDB notify yet, turn it off. DEV_XCHG and
UNK_FIS are handled by EH and thus turned on.
* sil24_softreset() usually fails to recover the port after DEV_XCHG.
ATA_PORT_HARDRESET is used as recovery action for DEV_XCHG.
* sil24 may be invoked without any active command. e.g. DEV_XCHG irq
occuring while no qc in progress still triggers EH and will reset
the port and revalidate attached device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Use new SCR and on/offline functions. Note that for LLDD which know
it implements SCR callbacks, SCR functions are guaranteed to succeed
and ata_port_online() == !ata_port_offline().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Rename ata_down_sata_spd_limit() and friends to sata_down_spd_limit()
and likewise for simplicity & consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Data structures residing on memory and fetched by the controller
should have LE ordering. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's no need to perform hardreset during driver initialization.
It's already done during host reset and even if the controller is in
some wacky state, we now have proper hardreset to back us up.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement hardreset according to the datasheet. The old hardreset
didn't reset controller status and the controller might not be ready
after reset. Also, as SStatus is a bit flakey after hardreset,
sata_std_hardrset() didn't use to wait long enough before proceeding.
Note that as we're not depending on SStatus, DET==1 condition cannot
be used to wait for link, so use shorter timeout for no device case.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Nothing, not the datasheet nor the errats, says this delay is
necessary and with the previous PORT_CS_INIT change, we know the
controller is in good state. Kill 10ms sleep.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure the controller has no pending commands and ready for command
before issuing SRST.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement sil24_init_port which performs port initialization via
PORT_CS_INIT. To be used later by softreset and EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SiI3124 might lose completion interrupt if completion interrupt occurs
shortly after SLOT_STAT register is read for the previous completion
interrupt if it is operating in PCI-X mode.
This currently doesn't trigger as libata never queues more than one
command, but it will with NCQ changes. This patch implements the
workaround - turning on WoC and explicitly clearing interrupt.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All sil24 controllers share the same host flags except for NPORTS.
Consolidate them into SIL24_COMMON_FLAGS.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sil24_softreset calculated timeout by adding ATA_TMOUT_BOOT * HZ to
jiffies; however, as ATA_TMOUT_BOOT is already in jiffies, multiplying
by HZ makes the value way off. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
@verbose was added to ata_reset_fn_t because AHCI complained during
probing if no device was attached to the port. However, muting
failure message isn't the correct approach. Reset methods are
responsible for detecting no device condition and finishing
successfully. Now that AHCI softreset is fixed, kill @verbose.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Overriding the whole EH code is a per-transport, not per-host thing.
Move ->eh_strategy_handler to the transport class, same as
->eh_timed_out.
Downside is that scsi_host_alloc can't check for the total lack of EH
anymore, but the transition period from old EH where we needed it is
long gone already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename ATA_FLAG_PORT_DISABLED to ATA_FLAG_DISABLED for consistency.
(ATA_FLAG_* are always about ports).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCSI midlayer has moved hostt->eh_timed_out to transport template. As
libata doesn't need full-blown transport support yet, implement
minimal transport for libata. No transport class or whatsoever, just
empty transport template with ->eh_timed_out hook.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sil24 softreset timeout was > 100ms (100 loops with msleep(1)), which
turned out to be too short for some devices (ASI ARAID99 2000). This
patch converts sil24 softreset waiting loop to use proper timeout
condition and lengthen the timeout to ATA_TMOUT_BOOT secs and check
interval to 100ms. Chisato Yamauchi discovered the problem and
supplied initial patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Chisato Yamauchi <cyamauch@plamo.linet.gr.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sil24 softreset routine used to check sata_dev_present() after
SRST is complete in the hope that SRST may do some good even when
SStatus reports no device. This is okay as long as SRST timeout is
short (> 100ms in the current code) but it seems that not all SATA
devices are happy with short SRST timeout.
This patch makes softreset exit early without performing actual SRST
if SStatus reports no device in preparation for lengthening SRST
timeout.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
mwdma_mask was not copied from port_info to probe_ent. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a new PCI ID for SiI 3124. Reported by Silicon Image.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The previous dev->max_sectors patch made sht->max_sectors meaningless.
Kill all initializations of sht->max_sectors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
cdb_len is per-device property. Sharing cdb_len on ap results in
inaccurate configuration on revalidation and hotplugging. This patch
makes cdb_len per-device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Now that libata is smart enough to handle both soft and hard resets,
add hardreset method. Note that sil24 hardreset doesn't supply
signature; still, the new reset mechanism can make good use of it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
->eng_timeout cannot be invoked with NULL qc anymore. Add an
assertion in ata_scsi_error() and kill NULL qc handling from all
->eng_timeout callbacks.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement ata_eh_qc_complete/retry() using scsi_eh_finish_cmd() and
scsi_eh_flush_done_q(). This removes all eh scsicmd finish hacks from
low level drivers.
This change was first suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Return AC_ERR_* mask from issue fuctions instead of 0/-1. This
enables things like failing a qc with AC_ERR_HSM when the device
doesn't set DRDY when the qc is about to be issued.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add detailed AC_ERR_* flags and use them. Long-term goal is to
describe all errors with err_mask and tf combination (tf for failed
sector information, etc...). After proper error diagnosis is
implemented, sense data should also be generated from err_mask instead
of directly from hardware tf registers as it is currently.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff Garzik