Add HPET(s) into resource map. This will allow for the HPET(s) to be
visibile within /proc/iomem.
Signed-off-by: Aaron Durbin <adurbin@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch places the IOAPIC(s) and the Local APIC specified by ACPI
tables into the resource map. The APICs will then be visible within
/proc/iomem
Signed-off-by: Aaron Durbin <adurbin@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Add early i386 fault handlers with debug information for common faults.
Handles:
divide error
invalid opcode
protection fault
page fault
Also adds code to detect early recursive/multiple faults and halt the
system when they happen (taken from x86_64.)
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
We allow for the fact that the guest kernel may not run in ring 0. This
requires some abstraction in a few places when setting %cs or checking
privilege level (user vs kernel).
This is Chris' [RFC PATCH 15/33] move segment checks to subarch, except rather
than using #define USER_MODE_MASK which depends on a config option, we use
Zach's more flexible approach of assuming ring 3 == userspace. I also used
"get_kernel_rpl()" over "get_kernel_cs()" because I think it reads better in
the code...
1) Remove the hardcoded 3 and introduce #define SEGMENT_RPL_MASK 3 2) Add a
get_kernel_rpl() macro, and don't assume it's zero.
And:
Clean up of patch for letting kernel run other than ring 0:
a. Add some comments about the SEGMENT_IS_*_CODE() macros.
b. Add a USER_RPL macro. (Code was comparing a value to a mask
in some places and to the magic number 3 in other places.)
c. Add macros for table indicator field and use them.
d. Change the entry.S tests for LDT stack segment to use the macros
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Abstract sensitive instructions in assembler code, replacing them with macros
(which currently are #defined to the native versions). We use long names:
assembler is case-insensitive, so if something goes wrong and macros do not
expand, it would assemble anyway.
Resulting object files are exactly the same as before.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix
linux/arch/x86_64/kernel/process.c: In function __switch_to:
linux/arch/x86_64/kernel/process.c:626: warning: assignment makes integer from pointer without a cast
Signed-off-by: Andi Kleen <ak@suse.de>
Add a feature check that checks that the gcc compiler has stack-protector
support and has the bugfix for PR28281 to make this work in kernel mode.
The easiest solution I could find was to have a shell script in scripts/
to do the detection; if needed we can make this fancier in the future
without making the makefile too complex.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
CC: Andi Kleen <ak@suse.de>
CC: Sam Ravnborg <sam@ravnborg.org>
This patch adds the per thread cookie field to the task struct and the PDA.
Also it makes sure that the PDA value gets the new cookie value at context
switch, and that a new task gets a new cookie at task creation time.
Signed-off-by: Arjan van Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
CC: Andi Kleen <ak@suse.de>
This patch adds the config options for -fstack-protector.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
CC: Andi Kleen <ak@suse.de>
Because it can take spinlocks.
Suggested by Mathieu Desnoyers
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Signed-off-by: Andi Kleen <ak@suse.de>
kexec: Avoid overwriting the current pgd (V4, i386)
This patch upgrades the i386-specific kexec code to avoid overwriting the
current pgd. Overwriting the current pgd is bad when CONFIG_CRASH_DUMP is used
to start a secondary kernel that dumps the memory of the previous kernel.
The code introduces a new set of page tables. These tables are used to provide
an executable identity mapping without overwriting the current pgd.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
kexec: Avoid overwriting the current pgd (V4, x86_64)
This patch upgrades the x86_64-specific kexec code to avoid overwriting the
current pgd. Overwriting the current pgd is bad when CONFIG_CRASH_DUMP is used
to start a secondary kernel that dumps the memory of the previous kernel.
The code introduces a new set of page tables. These tables are used to provide
an executable identity mapping without overwriting the current pgd.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Remove most of the special cases for the debug IST stack. This is a
follow on clean up patch, it requires the bug fix patch that adds
orig_ist.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
The EDD code would scan the command line as a fixed array, without
taking account of either whitespace, null-termination, the old
command-line protocol, late overrides early, or the fact that the
command line may not be reachable from INITSEG.
This should fix those problems, and enable us to use a longer command
line.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Based on a idea by Jeremy Fitzhardinge:
Replace the volatiles and memory clobbers in the PDA access with
telling gcc about access to a proxy PDA structure that doesn't
actually exist. But the dummy accesses give a defined ordering for
read/write accesses.
Also add some memory barriers to the early GS initialization to
make sure no PDA access is moved before it.
Advantage is some .text savings (probably most from better
code for accessing "current"):
text data bss dec hex filename
4845647 1223688 615864 6685199 66020f vmlinux
4837780 1223688 615864 6677332 65e354 vmlinux-pda
1.2% smaller code
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch updates x86_64 linker script to pack any .note.* sections
into a PT_NOTE segment in the output file.
To do this, we tell ld that we need a PT_NOTE segment. This requires
us to start explicitly mapping sections to segments, so we also need
to explicitly create PT_LOAD segments for text and data, and map the
sections to them appropriately. Fortunately, each section will
default to its previous section's segment, so it doesn't take many
changes to vmlinux.lds.S.
The corresponding change is already made for i386 in -mm and I'd like
this patch to join it. The section to segment mappings do change as do
the segment flags so some time in -mm would be good for that reason as
well, just in case.
In particular .data and .bss move from the text segment to the data
segment and .data.cacheline_aligned .data.read_mostly are put in the
data segment instead of a separate one.
I think that it would be possible to exactly match the existing section
to segment mapping and flags but it would be a more intrusive change and
I'm not sure there is a reason for the existing layout other than it is
what you get by default if you don't explicitly specify something else.
If there is a reason for the existing layout then I will of course make
the more intrusive change. If there is no reason we could probably drop
the executable or writable flags from some segments but I don't know how
much attention is paid to them anyway so it might not be worth the
effort.
The vsyscall related sections need to go in a different segment to the
normal data segment and so I invented a "user" segment to contain them.
I believe this should appear to be another data segment as far as the
kernel is concerned so the flags are setup accordingly.
The notes will be used in the Xen paravirt_ops backend to provide
additional information to the domain builder. I am in the process of
converting the xen-unstable kernels and tools over to this scheme at the
moment to support this in the future.
It has been suggested to me that the notes segment should have flags 0
(i.e. not readable) since it is only used by the loader and is not used
at runtime. For now I went with a readable segment since that is what
the i386 patch uses.
AK: dropped NOTES addition right now because the needed infrastructure
for that is not merged yet
Signed-off-by: Ian Campbell <ian.campbell@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
In long mode the %cs is largely a relic. However there are a few cases
like iret where it matters that we have a valid value. Without this
patch it is possible to enter the kernel in startup_64 without setting
%cs to a valid value. With this patch we don't care what %cs value
we enter the kernel with, so long as the cs shadow register indicates
it is a privileged code segment.
Thanks to Magnus Damm for finding this problem and posting the
first workable patch. I have moved the jump to set %cs down a
few instructions so we don't need to take an extra jump. Which
keeps the code simpler.
Signed-of-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Drop support for non e820 BIOS calls to get the memory map.
The boot assembler code still has some support, but not the C code now.
Signed-off-by: Andi Kleen <ak@suse.de>
When compiling a 64-bit kernel on an Ubuntu 6.06 32bit system (whose GCC is also
a cross-compiler for x86_64) I've seen that head.o is compiled as a 64-bit file
(while it should not) and ld complaining about this during linking:
[AK: it happens on all systems with new binutils]
ld: warning: i386:x86-64 architecture of input file
`arch/x86_64/boot/compressed/head.o' is incompatible with i386 output
I've verified that removing -m64 from compilation flags to turn
"-m64 -traditional -m32" into "-traditional -m32" fixes the issue.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andi Kleen <ak@suse.de>
NMIs are not supposed to track the irq flags, but TRACE_IRQS_IRETQ
did it anyways. Add a check.
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
- Remove a define that was used only once
- Remove the too large APIC ID check because we always support
the full 8bit range of APICs.
- Restructure code a bit to be simpler.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
ACPI went to great trouble to get the APIC version and CPU capabilities
of different CPUs before passing them to the mpparser. But all
that data was used was to print it out. Actually it even faked some data
based on the boot cpu, not on the actual CPU being booted.
Remove all this code because it's not needed.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Fix the pte_exec/mkexec page table accessor functions to really
use the NX bit. Previously they only checked the USER bit, but
weren't actually used for anything.
Then use them in change_page_attr() to manipulate the NX bit
properly.
Signed-off-by: Andi Kleen <ak@suse.de>
And replace all users with ordinary smp_processor_id. The function
was originally added to get some basic oops information out even
if the GS register was corrupted. However that didn't
work for some anymore because printk is needed to print the oops
and it uses smp_processor_id() already. Also GS register corruptions
are not particularly common anymore.
This also helps the Xen port which would otherwise need to
do this in a special way because it can't access the local APIC.
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Detect the situations in which the time after a resume from disk would
be earlier than the time before the suspend and prevent them from
happening on x86_64.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@suse.de>
In i386's entry.S, FIX_STACK() needs annotation because it
replaces the stack pointer. And the rest of nmi() needs
annotation in order to compile with these new annotations.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
From i386 x86-64 inherited code to force reserve the 640k-1MB area.
That was needed on some old systems.
But we generally trust the e820 map to be correct on 64bit systems
and mark all areas that are not memory correctly.
This patch will allow to use the real memory in there.
Or rather the only way to find out if it's still needed is to
try. So far I'm optimistic.
Signed-off-by: Andi Kleen <ak@suse.de>
A kprobe executes IRET early and that could cause NMI recursion and stack
corruption.
Note: This problem was originally spotted and solved by Andi Kleen in the
x86_64 architecture. This patch is an adaption of his patch for i386.
AK: Merged with current code which was a bit different.
AK: Removed printk in nmi handler that shouldn't be there in the first time
AK: Added missing include.
AK: added KPROBES_END
Signed-off-by: Fernando Vazquez <fernando@intellilink.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
A kprobe executes IRET early and that could cause NMI recursion and stack
corruption.
Note: This problem was originally spotted by Andi Kleen. This patch
adds fixes not included in his original patch.
[AK: Jan Beulich originally discovered these classes of bugs]
Signed-off-by: Fernando Vazquez <fernando@intellilink.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Mark i386-specific cpu cache functions as __cpuinit. They are all
only called from arch/i386/common.c:display_cache_info() that already is
marked as __cpuinit.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Mark i386-specific cpu identification functions as __cpuinit. They are all
only called from arch/i386/common.c:identify_cpu() that already is marked as
__cpuinit.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Mark i386-specific cpu init functions as __cpuinit. They are all
only called from arch/i386/common.c:identify_cpu() that already is marked as
__cpuinit. This patch also removes the empty function init_umc().
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
The different cpu_dev structures are all used from __cpuinit callers what
I can tell. So mark them as __cpuinitdata instead of __initdata. I am a
little bit unsure about arch/i386/common.c:default_cpu, especially when it
comes to the purpose of this_cpu.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
The init_amd() function is only called from identify_cpu() which is already
marked as __cpuinit. So let's mark it as __cpuinit.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
cpu_dev->c_identify is only called from arch/i386/common.c:identify_cpu(), and
this after generic_identify() already has been called. There is no need to call
this function twice and hook it in c_identify - but I may be wrong, please
double check before applying.
This patch also removes generic_identify() from cpu.h to avoid unnecessary
future nesting.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix for the x86_64 kernel mapping code. Without this patch the update path
only inits one pmd_page worth of memory and tramples any entries on it. now
the calling convention to phys_pmd_init and phys_init is to always pass a
[pmd/pud] page not an offset within a page.
Signed-off-by: Keith Mannthey<kmannth@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Implement pause_on_oops() on x86_64.
AK: I redid the patch to do the oops_enter/exit in the existing
oops_begin()/end(). This makes it much shorter.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Right now the kernel on x86-64 has a 100% lazy fpu behavior: after *every*
context switch a trap is taken for the first FPU use to restore the FPU
context lazily. This is of course great for applications that have very
sporadic or no FPU use (since then you avoid doing the expensive
save/restore all the time). However for very frequent FPU users... you
take an extra trap every context switch.
The patch below adds a simple heuristic to this code: After 5 consecutive
context switches of FPU use, the lazy behavior is disabled and the context
gets restored every context switch. If the app indeed uses the FPU, the
trap is avoided. (the chance of the 6th time slice using FPU after the
previous 5 having done so are quite high obviously).
After 256 switches, this is reset and lazy behavior is returned (until
there are 5 consecutive ones again). The reason for this is to give apps
that do longer bursts of FPU use still the lazy behavior back after some
time.
[akpm@osdl.org: place new task_struct field next to jit_keyring to save space]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch enables ACPI based physical CPU hotplug support for x86_64.
Implements acpi_map_lsapic() and acpi_unmap_lsapic() to support physical cpu
hotplug.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Make an mmconfig warning print the bus id with a regular format.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
cyrix_identify() should be __init because transmeta_identify() is.
tsc_init() is only called from setup_arch() which is marked as __init.
These two section mismatches have been detected using running modpost on
a vmlinux image compiled with CONFIG_RELOCATABLE=y.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Now for a completely different but trivial approach.
I just boot tested it with 255 CPUS and everything worked.
Currently everything (except module data) we place in
the per cpu area we know about at compile time. So
instead of allocating a fixed size for the per_cpu area
allocate the number of bytes we need plus a fixed constant
for to be used for modules.
It isn't perfect but it is much less of a pain to
work with than what we are doing now.
AK: fixed warning
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The implementation comes from Zach's [RFC, PATCH 10/24] i386 Vmi
descriptor changes:
Descriptor and trap table cleanups. Add cleanly written accessors for
IDT and GDT gates so the subarch may override them. Note that this
allows the hypervisor to transparently tweak the DPL of the descriptors
as well as the RPL of segments in those descriptors, with no unnecessary
kernel code modification. It also allows the hypervisor implementation
of the VMI to tweak the gates, allowing for custom exception frames or
extra layers of indirection above the guest fault / IRQ handlers.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
And add proper CFI annotation to it which was previously
impossible. This prevents "stuck" messages by the dwarf2 unwinder
when reaching the top of a kernel stack.
Includes feedback from Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
It's needed for external debuggers and overhead is very small.
Also make the actual notifier chain they use static
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
It's needed for external debuggers and overhead is very small.
Also make the actual notifier chain they use static
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Fix
linux/arch/i386/kernel/mpparse.c: In function #MP_bus_info#:
linux/arch/i386/kernel/mpparse.c:232: warning: comparison is always false due to limited range of data type
Signed-off-by: Andi Kleen <ak@suse.de>
Improve Kconfig description of CONFIG_CRASH_DUMP. Previously
it was too brief to be useful.
Cc: vgoyal@in.ibm.com
Cc: ebiederm@xmission.com
Signed-off-by: Andi Kleen <ak@suse.de>
I've noticed some erratic behavior while testing the X86_64 version
of monotonic_clock().
While spinning in a loop reading monotonic clock values (pinned to a
single cpu) I noticed that the difference between subsequent values
occasionally went negative (time going backwards).
I found that in the following code:
this_offset = get_cycles_sync();
/* FIXME: 1000 or 1000000? */
--> offset = (this_offset - last_offset)*1000 / cpu_khz;
}
return base + offset;
the offset sometimes turns out to be 0, even though
this_offset > last_offset.
+Added fix From: Toyo Abe <toyoa@mvista.com>
The x86_64-mm-monotonic-clock.patch in 2.6.18-rc4-mm2 made a change to
the updating of monotonic_base. It now uses cycles_2_ns().
I suggest that a set_cyc2ns_scale() should be done prior to the setup_irq().
Because cycles_2_ns() can be called from the timer ISR right after the irq0
is enabled.
Signed-off-by: Toyo Abe <toyoa@mvista.com>
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch moves the entry.S:error_entry to .kprobes.text section,
since code marked unsafe for kprobes jumps directly to entry.S::error_entry,
that must be marked unsafe as well.
This patch also moves all the ".previous.text" asm directives to ".previous"
for kprobes section.
AK: Following a similar i386 patch from Chuck Ebbert
AK: Also merged Jeremy's fix in.
+From: Jeremy Fitzhardinge <jeremy@goop.org>
KPROBE_ENTRY does a .section .kprobes.text, and expects its users to
do a .previous at the end of the function.
Unfortunately, if any code within the function switches sections, for
example .fixup, then the .previous ends up putting all subsequent code
into .fixup. Worse, any subsequent .fixup code gets intermingled with
the code its supposed to be fixing (which is also in .fixup). It's
surprising this didn't cause more havok.
The fix is to use .pushsection/.popsection, so this stuff nests
properly. A further cleanup would be to get rid of all
.section/.previous pairs, since they're inherently fragile.
+From: Chuck Ebbert <76306.1226@compuserve.com>
Because code marked unsafe for kprobes jumps directly to
entry.S::error_code, that must be marked unsafe as well.
The easiest way to do that is to move the page fault entry
point to just before error_code and let it inherit the same
section.
Also moved all the ".previous" asm directives for kprobes
sections to column 1 and removed ".text" from them.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
We have a test that looks for invalid pairings of certain athlon/durons
that weren't designed for SMP, and taint accordingly (with 'S') if we find
such a configuration. However, this test shouldn't fire if there's only
a single CPU present. It's perfectly valid for an SMP kernel to boot on UP
hardware for example.
AK: changed to num_possible_cpus()
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix a very dubious piece of code in
arch/i386/kernel/cpu/common.c:cpu_init(). This clears out %fs and
%gs, but clobbers %eax in the process without telling gcc. It turns
out that gcc happens to be not using %eax at that point anyway so it
doesn't matter much, but it looks like a bomb waiting to go off.
This does end up saving an instruction, because gcc wants %eax==0 for
the set_debugreg()s below.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Following x86-64 patches. Reuses code from them in fact.
Convert the standard backtracer to do all output using
callbacks. Use the x86-64 stack tracer implementation
that uses these callbacks to implement the stacktrace interface.
This allows to use the new dwarf2 unwinder for stacktrace
and get better backtraces.
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
This unifies the standard backtracer and the new stacktrace
in memory backtracer. The standard one is converted to use callbacks
and then reimplement stacktrace using new callbacks.
The main advantage is that stacktrace can now use the new dwarf2 unwinder
and avoid false positives in many cases.
I kept it simple to make sure the standard backtracer stays reliable.
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
Lockdep can call the dwarf2 unwinder early, and the dwarf2 code
uses safe_smp_processor_id which tries to access the local APIC page.
But that doesn't work before the APIC code has set up its fixmap.
Check for this case and always return boot cpu then.
Cc: jbeulich@novell.com
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
- Remove unused all_contexts parameter
No caller used it
- Move skip argument into the structure (needed for
followon patches)
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
tce_cache_blast_stress was useful during bringup to stress the IOMMU's
cache flushing. Now that we quiesce DMAs on every cache flush, using
_stress() brings the machine down to its knees once you put it under
load. Remove this debug / bringup code that isn't useful anymore
completely.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Introduce new function verify_bit_range(). Define two versions, one
for CONFIG_IOMMU_DEBUG enabled and one for disabled. Previously we
were checking that the bitmap was consistent every time we allocated
or freed an entry in the TCE table, which is good for debugging but
incurs an unnecessary penalty on non debug builds.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
is_at_popf() needs to test for the iret instruction as well as
popf. So add that test and rename it to is_setting_trap_flag().
Also change max insn length from 16 to 15 to match reality.
LAHF / SAHF can't affect TF, so the comment in x86_64 is removed.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The combination of "local_save_flags" and "local_irq_disable" seems to be
equivalent to "local_irq_save" (see code snips below). Consequently, replace
occurrences of local_save_flags+local_irq_disable with local_irq_save.
* local_irq_save
#define raw_local_irq_save(flags) \
do { (flags) = __raw_local_irq_save(); } while (0)
static inline unsigned long __raw_local_irq_save(void)
{
unsigned long flags = __raw_local_save_flags();
raw_local_irq_disable();
return flags;
}
* local_save_flags
#define raw_local_save_flags(flags) \
do { (flags) = __raw_local_save_flags(); } while (0)
Signed-off-by: Fernando Vazquez <fernando@intellilink.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Move it into srat.c No need to clutter up setup.c for it
And remove use in setup.c completely - it only guarded a printk
which can be done unconditionally.
Signed-off-by: Andi Kleen <ak@suse.de>
Removes code duplication between i386/x86-64.
Not needed anymore in setup.c since early_param cleanup
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
I think it was only needed for the printks and we can do them later.
I put in a single early_printk so that we know the kernel is alive
(early_printk doesn't need any locks)
This makes some things easier for initialization of unwind for
lockdep, which is needed by later patches.
cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
Instead of hackish manual parsing
Requires earlier i386 patchkit, but also fixes i386 early_printk again.
I removed some obsolete really early parameters which didn't do anything useful.
Also made a few parameters that needed it early (mostly oops printing setup)
Also removed one panic check that wasn't visible without
early console anyways (the early console is now initialized after that
panic)
This cleans up a lot of code.
Signed-off-by: Andi Kleen <ak@suse.de>
This patch replaces the open-coded early commandline parsing
throughout the i386 boot code with the generic mechanism (already used
by ppc, powerpc, ia64 and s390). The code was inconsistent with
whether it deletes the option from the cmdline or not, meaning some of
these will get passed through the environment into init.
This transformation is mainly mechanical, but there are some notable
parts:
1) Grammar: s/linux never set's it up/linux never sets it up/
2) Remove hacked-in earlyprintk= option scanning. When someone
actually implements CONFIG_EARLY_PRINTK, then they can use
early_param().
[AK: actually it is implemented, but I'm adding the early_param it in the next
x86-64 patch]
3) Move declaration of generic_apic_probe() from setup.c into asm/apic.h
4) Various parameters now moved into their appropriate files (thanks Andi).
5) All parse functions which examine arg need to check for NULL,
except one where it has subtle humor value.
AK: readded acpi_sci handling which was completely dropped
AK: moved some more variables into acpi/boot.c
Cc: len.brown@intel.com
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
This makes it possible to modify CPU flags in command line
options without hacks.
And remove another copy in head64.c
Signed-off-by: Andi Kleen <ak@suse.de>
The lock prefix will cause an exception when used with the
popf instruction, so no need to continue searching after it's
found.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
There's no need to check for invalid DMA data direction in nommu and
gart since we do it in dma-mapping.h anyway before calling the
individual dma-ops.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Allows easier extension of the GDT by using the proper C symbol
for the size in the descriptor.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Add unwind annotations to arch/x86_64/lib/*.S, and also use the macros
provided by linux/linkage.h where-ever possible.
Some of the alternative instructions handling needed to be adjusted so
that the replacement code would also have valid unwind information.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
When testing for the REX instruction prefix, first check
for 32-bit mode because in compat mode the REX prefix is an
increment instruction.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Lock sections don't work the new dwarf2 unwinder
This generates slightly smaller code. It adds one more taken
jump to the fast path.
Also move the trampolines into semaphore.S and add proper CFI
annotations.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Make translation_disabled a uchar rather than an int
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The pci_get_device() API decrements the reference count on the 'from'
parameter when it continues searching. Therefore, take a ref count on
Calgary bus when we initialize them in either translated or
non-translated mode.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
We were freeing the iommu_table and leaking the bitmap pages. Also
rename it to calgary_free_bus, which is more accurate.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Move the tce_table_kva array, disabled bitmap and bus_to_phb array
into a new per bus 'struct calgary_bus_info'. Also slightly reorganize
build_tce_table and tce_table_setparms to avoid exporting bus_info to
tce.c.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Move initialization of all memory end variables to as early as
possible, so that dependent code doesn't need to check whether these
variables have already been set.
Change the range check in kunmap_atomic to actually make use of this
so that the no-mapping-estabished path (under CONFIG_DEBUG_HIGHMEM)
gets used only when the address is inside the lowmem area (and BUG()
otherwise).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The genapic field and the accessor macro weren't used anywhere.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
While an earlier patch already did a small step into that direction,
this patch moves initialization of all memory end variables to as
early as possible, so that dependent code doesn't need to check
whether these variables have already been set.
Also, remove a misleading (perhaps just outdated) comment, and make
static a variable only used in a single file.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
... instead of using a CONFIG option. The config option still controls
if the resulting executable actually has unwind information.
This is useful to prevent compilation errors when users select
CONFIG_STACK_UNWIND on old binutils and also allows to use
CFI in the future for non kernel debugging applications.
Cc: jbeulich@novell.com
Cc: sam@ravnborg.org
Signed-off-by: Andi Kleen <ak@suse.de>
Remove some unlinuxy ways to write function parameter definitions.
Remove some stray "return;"s
No functional change.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
They did not really belong into io_apic.c. Move them into a new file
and clean it up a bit.
Also remove outdated ATI quirk that was obsolete,
Signed-off-by: Andi Kleen <ak@suse.de>
The MPS table specification says that the operating system should
renumber the IO-APICs following the table as needed. However in
ACPI this is not allowed or neeeded and all x86-64 systems are ACPI
compliant.
The code was already disabled on some systems because it caused
problems there. Remove it completely now.
CC: mdomsch@dell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Bugzilla #6552 says:
"In arch/i386/boot/setup.S, movw is used instead of movb for PS/2 mouse
information, although it is unsigned char. This does not harm, because
the jmp instruction overwritten by movw is used before executing movw,
and never be used again"
I've no idea if this is a real bug or how it gets fixed, so I'm submitting
it for review instead of letting it die of boredom in bugzilla. Aditionally
to i386, I've changed x86-64, which mirrors the same code.
Credits to Yoshinori K. Okuji, who found the problem and suggested a fix.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The IO APIC code had lots of duplicated code to read/write 64bit
routing entries into the IO-APIC. Factor this out int common read/write
functions
In a few cases the IO APIC lock is taken more often now, but this
isn't a problem because it's all initialization/shutdown only
slow path code.
Similar to earlier x86-64 patch.
Includes a fix by Jiri Slaby for a mistake that broke resume
Signed-off-by: Andi Kleen <ak@suse.de>
The IO APIC code had lots of duplicated code to read/write 64bit
routing entries into the IO-APIC. Factor this out int common read/write
functions
In a few cases the IO APIC lock is taken more often now, but this
isn't a problem because it's all initialization/shutdown only
slow path code.
Signed-off-by: Andi Kleen <ak@suse.de>
PIC mode is an outdated way to drive the APICs that was used on
some early MP boards. It is not supported in the ACPI model.
It is unlikely to be ever configured by any x86-64 system
Remove it thus.
Signed-off-by: Andi Kleen <ak@suse.de>
No 64bit EISA or Microchannel systems ever. Remove the left over code
in the IO-APIC driver and the mptable parser
Signed-off-by: Andi Kleen <ak@suse.de>
This was an old workaround for broken MP-BIOS. The user could
specify overwrites on the command line.
I've never seen it being used for anything on 64bit. So get
rid of it for now.
Signed-off-by: Andi Kleen <ak@suse.de>
IO-APIC or local APIC can only be disabled at runtime anyways and
Kconfig has forced these options on for a long time now.
The Kconfigs are kept only now for the benefit of the shared acpi
boot.c code.
Signed-off-by: Andi Kleen <ak@suse.de>
- Move them to a pure assembly file. Previously they were in
a C file that only consisted of inline assembly. Doing it in pure
assembler is much nicer.
- Add a frame.i include with FRAME/ENDFRAME macros to easily
add frame pointers to assembly functions
- Add dwarf2 annotation to them so that the new dwarf2 unwinder
doesn't get stuck on them
- Random cleanups
Includes feedback from Jan Beulich and a UML build fix from Andrew
Morton.
Cc: jbeulich@novell.com
Cc: jdike@addtoit.com
Signed-off-by: Andi Kleen <ak@suse.de>
Previously it didn't align. Use the same one as the C compiler
in blended mode, which is good for K8 and Core2 and doesn't hurt
on P4.
Signed-off-by: Andi Kleen <ak@suse.de>
- Move the slow path fallbacks to their own assembly files
This makes them much easier to read and is needed for the next change.
- Add CFI annotations for unwinding (XXX need review)
- Remove constant case which can never happen with out of line spinlocks
- Use patchable LOCK prefixes
- Don't use lock sections anymore for inline code because they can't
be expressed by the unwinder (this adds one taken jump to the lock
fast path)
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Use knowledge about EFLAGS layout (bits 22:63 are always 0) to distingush
EFLAGS word and kernel address in the spin lock stack frame.
Signed-off-by: Andi Kleen <ak@suse.de>
This ports the algorithm from x86-64 (with improvements) to i386.
Previously this only worked for frame pointer enabled kernels.
But spinlocks have a very simple stack frame that can be manually
analyzed. Do this.
Signed-off-by: Andi Kleen <ak@suse.de>
A few trivial spelling and grammar mistakes picked up in
"arch/x86_64/aperture.c", "arch/x86_64/crash.c" and
"arch/x86_64/apic.c". I think all are correct fixes but am ever aware
of my fallibility :o) This is my first patch submission so all
feedback is appreciated, esp. WRT CCing to Linus, Andi and
trivial@kernel.org, is this correct? And which is the most appropriate
kernel version to diff against? If any.
Should apply cleanly to 2.6.18-rc1
Signed-off-by: Adam Henley <adamazing@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>
- adam
Hello,
Following my discussion with Andi. Here is a patch that introduces
two new TIF flags to simplify the context switch code in __switch_to().
The idea is to minimize the number of cache lines accessed in the common
case, i.e., when neither the debug registers nor the I/O bitmap are used.
This patch covers the x86-64 modifications. A patch for i386 follows.
Changelog:
- add TIF_DEBUG to track when debug registers are active
- add TIF_IO_BITMAP to track when I/O bitmap is used
- modify __switch_to() to use the new TIF flags
<signed-off-by>: eranian@hpl.hp.com
Signed-off-by: Andi Kleen <ak@suse.de>
For NUMA optimization and some other algorithms it is useful to have a fast
to get the current CPU and node numbers in user space.
x86-64 added a fast way to do this in a vsyscall. This adds a generic
syscall for other architectures to make it a generic portable facility.
I expect some of them will also implement it as a faster vsyscall.
The cache is an optimization for the x86-64 vsyscall optimization. Since
what the syscall returns is an approximation anyways and user space
often wants very fast results it can be cached for some time. The norma
methods to get this information in user space are relatively slow
The vsyscall is in a better position to manage the cache because it has direct
access to a fast time stamp (jiffies). For the generic syscall optimization
it doesn't help much, but enforce a valid argument to keep programs
portable
I only added an i386 syscall entry for now. Other architectures can follow
as needed.
AK: Also added some cleanups from Andrew Morton
Signed-off-by: Andi Kleen <ak@suse.de>
This patch adds a vgetcpu vsyscall, which depending on the CPU RDTSCP
capability uses either the RDTSCP or CPUID to obtain a CPU and node
numbers and pass them to the program.
AK: Lots of changes over Vojtech's original code:
Better prototype for vgetcpu()
It's better to pass the cpu / node numbers as separate arguments
to avoid mistakes when going from SMP to NUMA.
Also add a fast time stamp based cache using a user supplied
argument to speed things more up.
Use fast method from Chuck Ebbert to retrieve node/cpu from
GDT limit instead of CPUID
Made sure RDTSCP init is always executed after node is known.
Drop printk
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch adds initalization of the RDTSCP auxilliary values to CPU numbers
to time.c. If RDTSCP is available, the MSRs are written with the respective
values. It can be later used to initalize per-cpu timekeeping variables.
AK: Some cleanups. Move externs into headers and fix CPU hotplug.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
AK: This redoes the changes I temporarily reverted.
Intel now has support for Architectural Performance Monitoring Counters
( Refer to IA-32 Intel Architecture Software Developer's Manual
http://www.intel.com/design/pentium4/manuals/253669.htm ). This
feature is present starting from Intel Core Duo and Intel Core Solo processors.
What this means is, the performance monitoring counters and some performance
monitoring events are now defined in an architectural way (using cpuid).
And there will be no need to check for family/model etc for these architectural
events.
Below is the patch to use this performance counters in nmi watchdog driver.
Patch handles both i386 and x86-64 kernels.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
I've had good experiences with having this on by default on x86-64.
It turns nasty hangs into easier to debug oopses.
Enable the local APIC wdog by default for systems newer than 2004.
This comes from a strange compromise: according to arjan the reason
it was off by default was some old IBM systems that corrupted
registered when NMI happened in SMI. Can't remember more specific,
but >= 2004 should avoid these. It's probably overly broad
because most older systems should be ok (and the really old systems
won't be supported by the local apic watchdog anyways)
Signed-off-by: Andi Kleen <ak@suse.de>
After a crash we should wait for NMI IPI event and not for external NMI or
NMI watchdog tick.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
After a crash we should wait for NMI IPI event and not for external NMI or
NMI watchdog tick.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch makes the following needlessly global functions static:
- nmi_int.c: profile_exceptions_notify()
- nmi_timer_int.c: profile_timer_exceptions_notify()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andi Kleen <ak@suse.de>
When a unknown NMI happened the panic would claim a NMI watchdog timeout.
Also it would check the variable set by nmi_watchdog=panic and panic then.
Fix up the panic message to be generic
Unconditionally panic on unknown NMI when panic on unknown nmi is enabled.
Noticed by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Making NMI suspend/resume work with SMP. We use CPU hotplug to offline
APs in SMP suspend/resume. Only BSP executes sysdev's .suspend/.resume
method. APs should follow CPU hotplug code path.
And:
+From: Don Zickus <dzickus@redhat.com>
Makes the start/stop paths of nmi watchdog more robust to handle the
suspend/resume cases more gracefully.
AK: I merged the two patches together
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Clean up some of the output messages on the nmi error paths to make more
sense when they are displayed. This is mainly a cosmetic fix and
shouldn't impact any normal code path.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
To quote Alan Cox:
The default Linux behaviour on an NMI of either memory or unknown is to
continue operation. For many environments such as scientific computing
it is preferable that the box is taken out and the error dealt with than
an uncorrected parity/ECC error get propogated.
A small number of systems do generate NMI's for bizarre random reasons
such as power management so the default is unchanged. In other respects
the new proc/sys entry works like the existing panic controls already in
that directory.
This is separate to the edac support - EDAC allows supported chipsets to
handle ECC errors well, this change allows unsupported cases to at least
panic rather than cause problems further down the line.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Adds a new /proc/sys/kernel/nmi_watchdog call that will enable/disable the
nmi watchdog.
By entering a non-zero value here, a user can enable the nmi watchdog to
monitor the online cpus in the system. By entering a zero value here, a
user can disable the nmi watchdog and free up a performance counter which
could then be utilized by the oprofile subsystem, otherwise oprofile may be
short a counter when in use.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Adds a new /proc/sys/kernel/nmi call that will enable/disable the nmi
watchdog.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Removes the un/set_nmi_callback and reserve/release_lapic_nmi functions as
they are no longer needed. The various subsystems are modified to register
with the die_notifier instead.
Also includes compile fixes by Andrew Morton.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
We need TIF_RESTORE_SIGMASK in order to support ppoll() and pselect()
system calls. This patch originally came from Andi, and was based
heavily on David Howells' implementation of same on i386. I fixed a typo
which was causing do_signal() to use the wrong signal mask.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch cleans up the NMI interrupt path. Instead of being gated by if
the 'nmi callback' is set, the interrupt handler now calls everyone who is
registered on the die_chain and additionally checks the nmi watchdog,
reseting it if enabled. This allows more subsystems to hook into the NMI if
they need to (without being block by set_nmi_callback).
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch includes the changes to make the nmi watchdog on i386 SMP aware.
A bunch of code was moved around to make it simpler to read. In addition,
it is now possible to determine if a particular NMI was the result of the
watchdog or not. This feature allows the kernel to filter out unknown NMIs
easier.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch includes the changes to make the nmi watchdog on x86_64 SMP
aware. A bunch of code was moved around to make it simpler to read. In
addition, it is now possible to determine if a particular NMI was the result
of the watchdog or not. This feature allows the kernel to filter out
unknown NMIs easier.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Incorporates the new performance counter reservation system in oprofile.
Also cleans up a lot of the initialization code. The code original zero'd
out every register associated with performance counters regardless if those
registers were used or not. This causes issues with the nmi watchdog.
Now oprofile tries to reserve registers and gives up if it can't get them.
Cc: levon@movementarian.org
Cc: oprofile-list@lists.sf.net
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Adds basic infrastructure to allow subsystems to reserve performance
counters on the x86 chips. Only UP kernels are supported in this patch to
make reviewing easier. The SMP portion makes a lot more changes.
Think of this as a locking mechanism where each bit represents a different
counter. In addition, each subsystem should also reserve an appropriate
event selection register that will correspond to the performance counter it
will be using (this is mainly neccessary for the Pentium 4 chips as they
break the 1:1 relationship to performance counters).
This will help prevent subsystems like oprofile from interfering with the
nmi watchdog.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
There are some machines around (large xSeries or Unisys ES7000) that
need physical IO-APIC destination mode to access all of their IO
devices. This currently doesn't work in UP kernels as used in
distribution installers.
This patch allows to compile even UP kernels as GENERICARCH which
allows to use physical or clustered APIC mode.
Signed-off-by: Andi Kleen <ak@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SOUND] sparc/amd7930: Use __devinit and __devinitdata as needed.
[SUNLANCE]: Mark sparc_lance_probe_one as __devinit.
[SPARC64]: Fix section-mismatch errors in solaris emul module.
If there is only 1 node in the system cpus should think they are apart of
some other node.
If cases where a real numa system boots the Flat numa option make sure the
cpus don't claim to be apart on a non-existent node.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Assume that a cpu is *physically* offlined at boot time...
Because smpboot.c::smp_boot_cpu_map() canoot find cpu's sapicid,
numa.c::build_cpu_to_node_map() cannot build cpu<->node map for
offlined cpu.
For such cpus, cpu_to_node map should be fixed at cpu-hot-add.
This mapping should be done before cpu onlining.
This patch also handles cpu hotremove case.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Problem description:
We have additional_cpus= option for allocating possible_cpus. But nid
for possible cpus are not fixed at boot time. cpus which is offlined at
boot or cpus which is not on SRAT is not tied to its node. This will
cause panic at cpu onlining.
Usually, pxm_to_nid() mapping is fixed at boot time by SRAT.
But, unfortunately, some system (my system!) do not include
full SRAT table for possible cpus. (Then, I use
additiona_cpus= option.)
For such possible cpus, pxm<->nid should be fixed at
hot-add. We now have acpi_map_pxm_to_node() which is also
used at boot. It's suitable here.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_PHYSICAL_START set to a non default values the i386
boot_ioremap code calculated its pte index wrong and users of boot_ioremap
have their areas incorrectly mapped (for me SRAT table not mapped during
early boot). This patch removes the addr < BOOT_PTE_PTRS constraint.
[ Keith says this is applicable to 2.6.16 and 2.6.17 as well ]
Signed-off-by: Keith Mannthey<kmannth@us.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: <stable@kernel.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
init_socksys() was marked __init but invoked from a
non-__init function.
Use the correct module_{init,exit}() faciltiies while we're
here and eliminate some seriously bogus ifdefs.
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, sparc64 doesn't have an easy way to do a "64 X 64 -->
128" bit multiply like PowerPC and IA64 do. We were doing a
"64 X 64 --> 64" bit multiple which causes overflow very quickly with
a 30-bit quotient shift.
So use a quotientshift count of 10 instead of 30, just like x86 and
ARM do.
This also fixes the wrapping of printk timestamp values every ~17
seconds.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] sw_any_bug_dmi_table can be used on resume, so it isn't initdata
[CPUFREQ] Fix some more CPU hotplug locking.
[CPUFREQ] Workaround for BIOS bug in software coordination of frequency
[CPUFREQ] Longhaul - Add voltage scaling to driver
[CPUFREQ] Fix sparse warning in ondemand
[CPUFREQ] make drivers/cpufreq/cpufreq_ondemand.c:powersave_bias_target() static
[CPUFREQ] Longhaul - Add ignore_latency option
[CPUFREQ] Longhaul - Disable arbiter
[CPUFREQ][2/2] ondemand: updated add powersave_bias tunable
[CPUFREQ][1/2] ondemand: updated tune for hardware coordination
[CPUFREQ] Fix typo.
iommu_init() and iounit_init() are never called for sun4, but that's not
enough - these calls should be ifdefed out since the functions in question
simply do not exist for CONFIG_SUN4 kernel.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Back when pci_dev had base_address[], loop of form
base = &...->base_address[0];
for (.....) {
...
*base++ = addr;
}
was fine, but when that array got spread in ->resource[...].start
replacing the initialization with
base = &...->resource[0].start;
was not a sufficient modification. IOW this code got broken for cases
when there had been more than one resource to fill. All way back in
2.3.41-pre3...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sw_any_bug_dmi_table can be used on resume, so it isn't initdata.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Dave Jones <davej@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (64 commits)
[BLOCK] dm-crypt: trivial comment improvements
[CRYPTO] api: Deprecate crypto_digest_* and crypto_alg_available
[CRYPTO] padlock: Convert padlock-sha to use crypto_hash
[CRYPTO] users: Use crypto_comp and crypto_has_*
[CRYPTO] api: Add crypto_comp and crypto_has_*
[CRYPTO] users: Use crypto_hash interface instead of crypto_digest
[SCSI] iscsi: Use crypto_hash interface instead of crypto_digest
[CRYPTO] digest: Remove old HMAC implementation
[CRYPTO] doc: Update documentation for hash and me
[SCTP]: Use HMAC template and hash interface
[IPSEC]: Use HMAC template and hash interface
[CRYPTO] tcrypt: Use HMAC template and hash interface
[CRYPTO] hmac: Add crypto template implementation
[CRYPTO] digest: Added user API for new hash type
[CRYPTO] api: Mark parts of cipher interface as deprecated
[PATCH] scatterlist: Add const to sg_set_buf/sg_init_one pointer argument
[CRYPTO] drivers: Remove obsolete block cipher operations
[CRYPTO] users: Use block ciphers where applicable
[SUNRPC] GSS: Use block ciphers where applicable
[IPSEC] ESP: Use block ciphers where applicable
...
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (44 commits)
[S390] hypfs crashes with invalid mount option.
[S390] cio: subchannel evaluation function operates without lock
[S390] cio: always query all paths on path verification.
[S390] cio: update path groups on logical CHPID changes.
[S390] cio: subchannels in no-path state.
[S390] Replace nopav-message on VM.
[S390] set modalias for ccw bus uevents.
[S390] Get rid of DBG macro.
[S390] Use alternative user-copy operations for new hardware.
[S390] Make user-copy operations run-time configurable.
[S390] Cleanup in signal handling code.
[S390] Cleanup in page table related code.
[S390] Linux API for writing z/VM APPLDATA Monitor records.
[S390] xpram off by one error.
[S390] Remove kexec experimental flag.
[S390] cleanup appldata.
[S390] fix typo in vmcp.
[S390] Kernel stack overflow handling.
[S390] qdio slsb processing state.
[S390] Missing initialization in common i/o layer.
...
On detection of an EEH error, some Power4 systems seem to occasionally
want to be reset twice before they report themselves as fully recovered.
This patch re-arranges the code to attempt additional resets if the first
one doesn't take.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch causes fsl_soc.h to import the definition of phys_addr_t
itself, rather than relying on its includer to do so.
Signed-off-by: Scott Wood <scott@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Noticed that the U3_*CFA macros have some typos:
#define U3_HT_CFA0(devfn, off) \
((((unsigned long)devfn) << 8) | offset)
(refers to offset rather than off)
#define U3_AGP_CFA0(devfn, off) \
((1 << (unsigned long)PCI_SLOT(dev_fn)) \
| (((unsigned long)PCI_FUNC(dev_fn)) << 8) \
(refers to dev_fn rather than devfn)
Things happen to work, but there doesn't seem to be any reason these
shouldn't be functions. Overall behavior should be unchanged.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When there is a PCI-X mode 2 capable device behind the HT<->PCI-X
bridge, the pci core decides that the device has the extended 4K
config space, even though the bus is not operating in mode 2. This is
because the u3_ht pci ops silently accept offsets greater than 255 but
use only the 8 least significant bits, which means reading at offset
0x100 gets the data at offset 0x0, and causes confusion for lspci.
Reject accesses to configuration space offsets greater than 255.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes the assignment of pending registers to IRQ numbers for
the IPIC; the code previously assigned all IRQs to the high pending word
regardless of which word the interrupt belonged to.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch changes the io operations so that they are out of line if
CONFIG_PPC_ISERIES is set and includes a firmware feature check in
that case.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update to the PowerPC PCI error recovery code.
Add code to enable MMIO if a device driver reports that it is capable
of recovering on its own. One anticipated use of this having a device
driver enable MMIO so that it can take a register dump, which might
then be followed by the device driver requesting a full reset.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add wrapper around the rtas call to enable MMIO or DMA on a frozen pci
slot.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up subroutine documentation; mostly formatting changes, with
some new content.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This corrects a pci_dev get/put imbalance that can occur only in
highly unlikely situations (kmalloc failures, pci devices with
overlapping resource addresses). No actual failures seen, this was
spotted during code review.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The stack frame address was being printed incorrectly in the backtrace
option of XMON on PPC. This patch fixes it to print the actual stack
address instead of the address of the local variable that contains it.
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Jakub noticed the cputable.c entry for Xilinx Virtex-4 FX was missing
a .platform value, so the AT_PLATFORM value wouldn't be set correctly.
This adds it.
Signed-off-by: Peter Bergner <bergner@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup for user headers, as noted:
asm-sh/page.h requires asm-generic/memory_model.h, which does not exist in exported headers
asm-sh/ptrace.h requires asm/ubc.h, which does not exist in exported headers
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch removes obsolete block operations of the simple cipher type
from drivers. These were preserved so that existing users can make a
smooth transition. Now that the transition is complete, they are no
longer needed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds block cipher algorithms for S390. Once all users of the
old cipher type have been converted the existing CBC/ECB non-block cipher
operations will be removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Accelerated versions of crypto algorithms must carry a distinct driver name
and priority in order to distinguish themselves from their generic counter-
part.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that the tfm is passed directly to setkey instead of the ctx, we no
longer need to pass the &tfm->crt_flags pointer.
This patch also gets rid of a few unnecessary checks on the key length
for ciphers as the cipher layer guarantees that the key length is within
the bounds specified by the algorithm.
Rather than testing dia_setkey every time, this patch does it only once
during crypto_alloc_tfm. The redundant check from crypto_digest_setkey
is also removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When an invalid mount option is specified, no root inode is created
for hypfs, hypfs_fill_super() returns with -EINVAL and then
hypfs_kill_super() is called. hypfs_kill_super() does not check if
the root inode has been initialized. This patch adds this check.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This introduces new user-copy operations which are optimized for
copying more than 256 Bytes on new hardware.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduces a struct uaccess_ops which allows setting user-copy
operations at run-time.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
adurbin@google.com