Currently it takes an error code as status, but what we really want to
tell is if the scan was aborted or not.
Also fix a bug where we were comparing firmware scan status values
with kernel error codes, which is obviously wrong. This meant
that ath6kl didn't detect when firmware informed about failed scans. I
doubt that this fix doesn't make any difference in practise but it
still needs to be fixed. This is fixed by adding an enum for the success
status code and checking for that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently firmware crash dump is printed only if debug is enabled.
Change it so that the crash dump is always printed.
Also move the code from init.c to hif.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If ath6kl_init_hw_stop() failed with an error WLAN_ENABLED would not
be cleared. Found during code review and just a theoretical issue.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The benefit from this is that user space can control hardware's power state
by putting interface up and down. This is handy if firmware gets to some
weird state.
The downside will be that putting interface up takes a bit longer,
I was measuring ~500 ms during interface up.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the name of the driver in struct sdio_driver is "ath6kl_sdio",
this is for example what uevent advertises. This is wrong as the module
is named as ath6kl.ko. Change it to "ath6kl" so that the names match.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl_tx_complete() was printing an error when packet was canceled.
That causes unnecessary errors when hardware is powered off.
Also change the error to a warning and cleanup the message.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's possible to busyloop forever in ath6kl_hif_intr_bh_handler(). Add
a check that it lasts only one second.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Refactor the code needed to boot the hardware to a separate function so
that it will be easier boot and shutdown hardware.
No functional changes (hopefully).
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use of cfg80211_scan_request is not valid after calling cfg80211_scan_done()
but ath6kl_cfg80211_scan_complete_event() was doing exactly that. Change
the function to call cfg80211_scan_done() last.
This was found during code review, I didn't see any visible problems
due to this bug.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wpa_supplicant was receiving incorrect frame contents in the
callback function that indicates the status of the frame transmitted.
This patch fixes a missing copy of the frame contents to a local
buffer. The local buffer keeps track of the last sent management frame.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Even though only a single concurrent remain-on-channel operation is
supported, there may be two pending remain-on-channel events (one to
indicate end of a canceled operation and another to indicate start of a
new operation). User space won't be able to distinguish these events
unless unique cookies are used.
The previous behavior resulted in wpa_supplicant getting quite
confused about the driver's offchannel state in various sequences
and this made the P2P state machine behave incorrectly. Use of
more than a single remain-on-channel cookie value fixes this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When compiling ath6kl for ARM with device tree tree compilation fails
with errors like:
include/linux/of.h: In function 'of_property_read_u32_array':
include/linux/of.h:249:10: error: 'ENOSYS' undeclared
Workaround this by including errno.h from init.c.
kvalo: improved commit log
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based control of power parameters, we use
available debugfs infrastructure. With these features user can control
power consumption by adjusting various sleep/wake up related parameters.
The feature has been added for testing purposes. All 5 parameters are
mandatory in correct order. They have to be written to the power_params
file. These are:
1) idle_period
2) no_of_pspoll
3) dtim_policy
4) tx_wakeup_policy
5) no_tx_to_wakeup
Example:
echo "200 1 0 1 1" > power_params
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based control of listen interval, we use
available debugfs infrastructure. Listen interval implies how frequently
we want the WLAN chip to wake up and synchronize the beacons in case it
is in sleep mode. The command requires two parameters in the following order:
1) listen_interval_time
2) listen_interval_beacons
The user has to write the listen interval_time (in msecs) and
listen_interval_beacons (in no. of beacons) to the listen_interval file in
ath6kl debug directory.
Example:
echo "30 1" > listen_interval
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add control flag CONNECT_WPS_FLAG if a WPS IE is present in the
Association Request IEs. This flag is needed when the station must
connect to a WPS-enabled AP.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move some of the debug logs to boot level because they are more
interesting when debugging boot issues.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove the wdev reference in struct ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Wlan parameters need to be configured for every vif
in target.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This option lets operate more than one vif in normal mode (AP/STA/IBSS)
when support for multiple vif is enabled. This modparam needs to be used
as
modprobe ath6kl multi_norm_if_support=1
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Virtual interface information need to be configured during
init time to the target. With MAX_NUM_VIF is restricted to
1, currently only a single vif is being configured.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use replace (un)register_netdev() with (un)register_netdevice()
so that the same ath6kl function can be used with
add_virtual_intf()/del_virtual_intf().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch removes all references to ar->vif and takes
vif from a list.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use this spinlock to protect the vif's data instead of
one from ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI ready event gives the mac address, cache this
mac address in struct ath6kl so that it can be used to
compute the mac address for other vif in case of multi vif.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Interface index is passed in wmi data header as well, use it
to get the corresponding vif structure.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
So that the deinitialization of ath6kl and vif are separated.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass vif structure to those functions instead of ath6kl because these
functions do vif specific information initialization.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use one which is available in vif structure instead.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Interface index is passed in wmi command header from target.
Use this index to get the appropriate vif.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass this index to target in wmi commands to specify the interface
for which the command needs to be handled.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ar->flag maintains interface stats. Move interface
specific states from ar->flag to vif->flags.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
vif specific information need to be moved from struct ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to use ath6kl_get_fw_iftype() to find out the
firmware interface type during initialization because the type
of the initial interface in INFRA_NETWORK. Hardcode the fw interface
type corresponding to INFRA_BSS instead of using ath6kl_get_fw_iftype().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This refactoring is done in a manner that it can be used
for multiple virtual interface.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to avoid using ar->wdev to get wiphy pointer, this
may need further cleanup for multi vif support.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ar is again taken from private area of net_device in ath6kl_init(), pass
ar directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based control of background scan interval,
we use available debugfs infrastructure. The feature has been added for
testing purposes. The user has to write the bgscan interval (in secs) to
the bgscan_interval file in ath6kl debug directory. To disable bgscan,
a '0' is to be written to the bgscan_interval file.
Example:
echo "2" > bgscan_interval
This will make the background scan interval as 2 seconds
kvalo: changed implementation so that there's only one call to
ath6kl_wmi_scanparams_cmd()
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
That way we htc level debug messages can be removed from hif files. Also
add few new messages and remove useless debug message about using
synchrous irq processing (we don't support anything else).
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's currently possible to dump full sdio packets, so dumping htc packets
is not strictly needed. So remove it, we can always add it back if
there ever comes a need for that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based QOS control we use the available debugfs
infrastructure. With this feature, user can make changes to qos parameters,
thereby allowing creation and deletion of user defined priority streams and
features like uapsd. This feature has been added for testing purposes.
All 21 parameters for the create_qos command are mandatory in the correct
order. They have to be written to the create_qos file in
the ath6kl debug directory. These parameters(in order) are:
1)user priority
2)direction
3)traffic class
4)traffic type
5)voice PS capability
6)min service intvl
7)max service intvl
8)inactivity intvl
9)suspension intvl
10)serv start time
11)tsid
12)nominal msdu
13)max msdu
14)min data rate
15)mean data rate
16)peak data rate
17)max burst size
18)delay bound
19)min phy rate
20)surplus bw allowance
21)medium time
To create a qos stream:
echo "6 2 3 1 1 9999999 9999999 9999999 7777777 0 6 45000 200 56789000
56789000 5678900 0 0 9999999 20000 0" > create_qos
delete_qos requires 2 parameters:
1)traffic class
2)tsid
To delete a qos stream:
echo "3 1" > delete_qos
kvalo: minor commit log cleanup
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The previous version did not really make much sense and the theoretical
maximum length would be a bit longer. Calculate the length more
accurately. In addition, there is no need to clear the buffer, so use
kmalloc instead of kzalloc. For bonus points, add the forgotten
cred_rpt_from_other value to the file.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add missing {}'s that caused ath6kl_sdio_suspend to always return -EINVAL
causing suspend to be aborted.
kvalo: I broke this in commit f7325b85e ("ath6kl: add sdio debug messages")
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sangwook found out that commit 639d0b89 ("ath6kl: read firmware start
address from hardware") broke firmware boot on ar6003 hw2.0 as it seems
it's not posible to automatically query the address from hardware. So
we need to hardcode the address for hw2.0.
Reported-by: Sangwook Lee <sangwook.lee@linaro.org>
Tested-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use vendor-specific suite selectors to allow CCKM to be configured.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new debugfs files keepalive and disconnect_timeout can be used to
fetch the current values and to change the values for keepalive and
disconnect event timeout (both in seconds).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Roaming mode can be changed by writing roam mode (default, bssbias, or
lock) to roam_mode. Forced roam can be requested by writing the BSSID
into force_roam.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new roam_table debugfs file can be used to display the current
roam table from the target.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This file can be used to fetch endpoint statistics counters and
to clear them by writing 0 to it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For some WPS test items, such as item "5.1.14"
STAUT must include the WSC IE in the 802.11 Association Request frame.
Therefore, add the corresponding IE in association message.
Signed-off-by: Kevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
smatch found that skb might be null in some cases in ath6kl_rx():
ath6kl/txrx.c +1252 ath6kl_rx(222) error: potential null derefence 'skb'.
This will happen when ath6kl is in AP mode and two clients send traffic
to each other.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no use for these, at least right now, so better to remove them.
If some of them are ever needed, we can always add them back.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Power save is enabled during ath6kl init. But when user space disables power
save, the system will go into suspend with power save disabled. The ath6kl
driver will now explicitly enable power save prior to entering suspend and
restore its previous setting upon resume
Signed-off-by: Chilam Ng <chilamng@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is just a four byte information of the received message
from ath6kl_htc_rxmsg_pending_handler(). Remove unnecessary
array representaion.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to process an htc_packet which is allocated for rx
but failed in sdio rx. Though it does not fix any real issue, it does
not make much sense to process the failed frame.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is found during the code review. As the leak would happen only
in failure case, the imapct is not easily visible.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Packet is not reclaimed when ath6kl_htc_rx_process_hdr() fails.
Fix this by deferring the packet deletion from comp_pktq till
ath6kl_htc_rx_process_hdr() returns success. This bug is found
in code review, impact is not easily visible as the leak happens
only in failure cases.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are places where tx_complete callbacks are called with
claiming the sdio function. It is not necessary to hold the
sdio func for longer. This may even affect the host side power
save, if it is supported by the controller.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to use spinlock primitive to
protect data which is accessed in hard irq context as
nothing is running in hard irq with this driver. The
spinlock primitive meant to protect data in softirq
context is more appropriate.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was disabled beacause there was a network stall
issue when scan is issued. This issue does not happen
with the new firmware (3.1.1.609), enable it back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Probably we never hit this condition, but in case we do, we may as
well put a return here instead of just printing a warning message and
then corrupting memory. The caller doesn't check the return code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By default SDIO multiport aggregation is disabled. It's useful to
get good throughput results. This patch enables it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We dereference adapter in the error handling code so this needed to
be fixed. This function is always called like:
adapter->if_ops.host_to_card(adapter, ...);
so adapter can never be NULL and I've removed the NULL check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous if statement means this that pointer is NULL so there
is no need to free it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare for adding backplane interconnect type support
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use SSB macros in order to clean up brcmfmac code
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare for adding backplane interconnect type support
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare for adding backplane interconnect type support
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merged brcmf_sdbrcm_chip_attach into brcmf_sdio_chip_attach
for better readability.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Same register writes have been done in brcmf_sdbrcm_probe_init
which is earlier in the same code path.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will provide a better code flow that fits the logic
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently backplane handle code is scatterd around dhd_sdio.c which
is not good for maintenance and adding new backplane interconnect
type support. This patch and the follow up patches are going to
abstract all chip backplane control code specific for sdio bus
into this new sdio_chip.c
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
4329 with chiprev 0 can not be found on any product. The code can
be removed.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.
Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add interface address so it can be mapped to a local
interface. Add max-ampdu and mpdu-density.
Print out the tid->baw_size
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a quick test, TDLS seemed to be working fine with ath9k, so
let's start advertising support for this in the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pointer returned by cfg80211_inform_bss is a referenced
struct. The orinoco driver does not need to keep the struct, so
we just release it.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes rndis_wlan to release referenced BSS structure returned by
cfg80211_inform_bss().
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initval tables are updated as per system team input to improve
rx performance and power accuracy at 5GHz.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To improve CCK sensitivity for AR9462 chips, performing
spur mitigation at 2440, 2464 frequencies alone is sufficient.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The buffer endianess conversion functions in srom.c had a size
argument giving number of bytes but the function converts words.
Providing the number of words to the function is more sensible
so that is done in this patch.
Reported-by: Pavel Roskin <proski@gnu.org>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usage of state decrease readability. Optimize the code flow to
get rid of it
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make a proper use of private data area of net device by storing
interface related data structure instead of generic driver data
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use brcmf_add_if for primary and virtual net device interfaces. This
is part of the net device interface clean up for fullmac.
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the receive path the frames are obtained from the dma using
multiple sk_buff that were linked using the skb next pointer.
This has been changed and it now used sk_buff lists and skb_queue
functions instead.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions ltoh16_buf() and htol16_buf() have been renamed
to le16_to_cpu_buf() and cpu_to_le16_buf() for more clarity
what it does.
Reported-by: Joe Perches <joe@perches.com>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver currently only supports STA operation. However, in
brcms_ops_add_interface() also AP and SSID mode were accepted.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Monitor mode functionality (not functional yet) requires transmit to be
muted after ops_start() is called, transmit is unmuted when the first
interface is added.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon ops_start(), a Mac80211 driver should enable receive functionality to
support monitor mode. Also, upon ops_stop(), it should disable rx.
Driver did not follow this rule so code has been changed.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transmit was muted in two ways: full mute and a partial mute called
'pre ism cac time' mute. But, this 'pre ism cac time' mute was done at
one place in the code (when tx_mute == false), and overridden later
on in another place in code.
To fix this, the 'pre ism cac time' mute has been replaced by a non
mute.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transmit can only be muted if the mac core is enabled. When brcms_b_init()
is called, the mac core is suspended. Brcms_b_init() calls a transmit mute
function that requires an enabled mac core. This code path is never taken,
but would have been taken in subsequent patches.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Softmac would bring its interface down on an RF kill switch condition,
without Mac80211 intervention. Because Mac80211 should be the only party
initiating interfaces going up and down, this functionality has been
removed.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Softmac would bring its interface down on a certain Minimum Power Save
related condition, without Mac80211 intervention. Because Mac80211 should
be the only party initiating interfaces going up and down, this functionality
has been removed. All notions of 'MPC' have been removed in the code as
well.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several member variables were never read.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip init sequence enables MPC (Minimum Power Consumption), but the
driver disables it after that. As there are no interfaces to enable this
mode the related code is unused (member variable wlc->mpc is false).
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use brcmf_del_if for primary and virtual net device interfaces. This
is part of the net device interface clean up for fullmac.
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Watchdog timer should be able to be stopped even firmware is not
loaded.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions in the receive patch of the fullmac now use sk_buff
list and skb_queue_xx() functions instead of dealing with list pointers
in the sk_buff directly.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The latest vendor (non-mac80211) driver of 9/22/2011 shows some new
device IDs for rtl8192cu. In addition, some typos in the table are
fixed and one duplicate is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmu_format_hex() filled a string buffer with byte
values from a data buffer. The calling function used this string
buffer in a printk. Now the calling function uses the kernel
function print_hex_dump_bytes().
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmu_pktfrombuf was only used in the brcmfmac source
and has been moved there. It has been refactored to match its use.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obviously the phy api should be used to interface with the phy. In
rate.h a table within phy was accessed directly by declaring the
table extern in rate.h itself. This patch fixes this using the
provided api function to obtain the table reference. This bypass
was found by a sparse warning on the table not being defined static.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In main.c a couple of functions were not static although they
were only locally used. Sparse gave warnings on them and these
functions have been made static.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data from the sprom consists of u16 values stored in little
endian notation over which a crc8 was determined. To validate this
the buffer needed to be converted for big-endian systems. Reading
the sprom data is now done per byte so conversion is only done
after a successful crc8 check.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The n-phy requested some srom variables that are no longer needed
and consequently not present in the srom revision 8 and higher that
this driver support. This code has been removed from the n-phy.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case the hardware crashes, a reinitialization internal to the driver
was performed. Since Mac80211 must be in the know of such an event as
well, ieee80211_restart_hw() is now called.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct brcmf_scan_results contained a 1 element array, but in reality
the number of scan results can be 0 or more, as indicated by the
count field in the same struct. Array has be redefined to be 0 elements
length to indicate the array is purely for reference.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved function to where it is called and made it more readable.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Made code more readable.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac driver registered with mac80211 with HT capability info
set to 40MHz intolerant. This cause any other station on the channel
to be forced to use 20MHz. This flag has been removed.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed defines from aiutils.h also present in soc.h.
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch added a check to get_key() but missed a couple
other places which need range checks.
The problem here is that wifi drivers have different numbers of keys.
The lower levels assume that they can have up to 4 default keys and
2 management keys but this driver only has the default keys so we
could go past the end of the ->keys[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wifi drivers can have up to 6 keys but the rndis_wlan only has 4 so
it needs to have its own checks to make sure we don't go out of
bounds. The add_key() function already checks but I added some
checks to del_key() and set_default_key().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code here treats very large values of "limit" as less than
MAX_POWER_RATE because of the cast to int. We should do the compare
as u32 instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When userspace requested that a scan not be
done with CCK rates, use 6 Mbps. This is used
for example for P2P scanning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwl_alloc_all routine is only called once. Delete the argument
and print an error in the calling routine if needed.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the HW rev. for both 105 and 135 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device tracing routines only use the priv pointer as an opaque
value. Change from a typed iwl_priv pointer to a null pointer and
eliminate the need to include iwl_priv.h. CMD_ASYNC is defined in
iwl_shared.h which is the only reason it is included.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WoWLAN API changed due to netdetect and
we now have a more generic "D3 configuration"
command that enables the sysassert & rfkill
wakeup triggers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A minor fix for the check that verifies that all given SSIDs (in req) exist
in the filters (the match sets)
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
This fixes the following sparse warnings:
drivers/net/ethernet/nvidia/forcedeth.c:2113:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2155:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2227:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2271:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2986:20: warning: symbol 'addr' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2963:6: originally declared here
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx byte count was off; instead use the hardware's count. Tx packet
count was counting pre-TSO packets; instead count on-the-wire packets.
Report hardware dropped frame count as rx_fifo_errors.
- The count of transmitted packets reported by the forcedeth driver
reports pre-TSO (TCP Segmentation Offload) packet counts and not the
count of the number of packets sent on the wire. This change fixes
the forcedeth driver to report the correct count. Fixed the code by
copying the count stored in the NIC H/W to the value reported by the
driver.
- Count rx_drop_frame errors as rx_fifo_errors:
We see a lot of rx_drop_frame errors if we disable the rx bottom-halves
for too long. Normally, rx_fifo_errors would be counted in this case.
The rx_drop_frame error count is private to forcedeth and is not
reported by ifconfig or sysfs. The rx_fifo_errors count is currently
unused in the forcedeth driver. It is reported by ifconfig as overruns.
This change reports rx_drop_frame errors as rx_fifo_errors.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function ndo_get_stats() updates most of the stats from hardware
registers, making the manual updates un-needed. This change removes
these manual updates. Main exception is rx_missed_errors which needs
manual update.
Another exception is rx_packets, still updated manually in this commit
to make sure this patch doesn't change behavior of driver. This will
be addressed by a future patch.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid a race, accidentally acknowledging an interrupt that
we didn't notice and won't immediately process. This is based solely
on code inspection; it is not known if there was an actual bug here.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forcedeth module is unloaded, there exists a path that can lead
to mod_timer() after del_timer_sync(), causing an oops. This patch
short-circuits this unneeded path, which originates in
nv_get_ethtool_stats().
Tested:
x86_64 16-way + 3 ethtool -S infinite loops + 100Mbps incoming traffic
+ rmmod/modprobe/ifconfig in a loop
Initial-Author: Salman Qazi <sqazi@google.com>
Discussion: http://patchwork.ozlabs.org/patch/123548/
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the bug added in commit v3.1-rc7-1055-gf9b491e
SKB can be NULL at this point, at least for cdc-ncm.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix compiler errors and warnings with CONFIG_PCI_IOV defined and not
defined.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If kmemdup() fails we leak the memory allocated to bss_desc.
This patch fixes the leak.
I also removed the pointless default assignment of 'NULL' to 'bss_desc'
while I was there anyway.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Though it's unlikely, di may be null, so we can't dereference
di->dma.dmactrlflags until we've checked it.
Move this de-reference after the check, and adjust the error
message to not require de-referencing di.
This is based upon Julia's original patch:
<1319846297-2985-2-git-send-email-julia@diku.dk>
Reported-by: Julia Lawall <julia@diku.dk>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes PHY transmission errors reported on some LP-PHY and HT-PHY
cards. For LP-PHY they were quite rare and not really noticable. On
HT-PHY they were critical, OFDM rates were not available at all.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scsi: drop unused Kconfig symbol
pci: drop unused Kconfig symbol
stmmac: drop unused Kconfig symbol
x86: drop unused Kconfig symbol
powerpc: drop unused Kconfig symbols
powerpc: 40x: drop unused Kconfig symbol
mips: drop unused Kconfig symbols
openrisc: drop unused Kconfig symbols
arm: at91: drop unused Kconfig symbol
samples: drop unused Kconfig symbol
m32r: drop unused Kconfig symbol
score: drop unused Kconfig symbols
sh: drop unused Kconfig symbol
um: drop unused Kconfig symbol
sparc: drop unused Kconfig symbol
alpha: drop unused Kconfig symbol
Fix up trivial conflict in drivers/net/ethernet/stmicro/stmmac/Kconfig
as per Michal: the STMMAC_DUAL_MAC config variable is still unused and
should be deleted.
* 'stable/vmalloc-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
net: xen-netback: use API provided by xenbus module to map rings
block: xen-blkback: use API provided by xenbus module to map rings
xen: use generic functions instead of xen_{alloc, free}_vm_area()
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
slave->duplex is a u8 type so the in bond_info_show_slave() when we
check "if (slave->duplex == -1)", it's always false.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to support other Optima types, introduced an accidental
regression that caused 88E8059 to come up in 10Mbit/sec.
The Yukon Optima supports a reverse auto-negotiation feature that
was incorrectly setup, and not needed. The feature could be used to
allow wake-on-lan at higher speeds. But doing it correctly would require
other changes to initialization.
Reported-by: Pavel Mateja <pavel@netsafe.cz>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.
Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.
Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing VRRP v2 using macvlan several problems were
discovered. VRRP is weird in that all routers participating
in a redundant group use the same virtual MAC address.
Macvlan is a natural driver to use for this but it doesn't
work. The problem is that packets with a macvlan device's
source address are not received.
The problem is actually a regression that date back almost 2 years now.
The original problems started with:
commit 618e1b7482
Author: Arnd Bergmann <arnd@arndb.de>
Date: Thu Nov 26 06:07:10 2009 +0000
macvlan: implement bridge, VEPA and private mode
This patches restores the original 2.6.32 behavior. Allowing multicast
packets received with the VRRP source address to be received.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.121.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During shutdown, it is impossible to reliably disable the timer and
reset_task threads. Each thread can schedule the other, which leads to
shutdown code that chases its tail.
To fix the problem, this patch removes the ability of tg3_reset_task to
schedule a new timer thread. To support this change, tg3_timer no
longer terminates itself, but rather goes into a polling mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for multiple threads in the tg3 driver to each attempt to
schedule a run of tg3_reset_task(). The multiple tg3_reset_task
executions could all wind up on the same queue (and execute serially) or
wind up on the queues of another processor (which could execute in
parallel). Either scenario is not what was truly desired.
This patch adds a new flag, TG3_FLAG_RESET_TASK_PENDING, and uses it to
determine whether or not to schedule another run of tg3_reset_task().
With the new flag comes two new functions to facilitate scheduling and
descheduling of tg3_reset_task().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to attempt to obtain the PCI function number from
the device rather than accept the number handed by the kernel. In
pass-through scenarios, the function number handed by the kernel may not
reflect the true function of the device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug where the irq error cleanup path did not free all
the resources it allocated.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Li <benli@broadcom.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the error recovery resource unwind path, it is possible for the
driver to attempt to unmap a fragment that hadn't been mapped. This
patch fixes the problem by correcting the "last" parameter supplied.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 4k tx bd segmentation code had a bug in the error cleanup path.
If the driver did not map all the physical fragments, the abort path
would wind up advancing the producer index beyond the point where the
setup code stopped. This would ultimately turn into a tx recovery error
where the driver would expect the skb pointer to be set when it isn't.
This patch fixes the problem, and then makes the code a little easier to
understand.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
APE mutex register blocks are shared by all ports of multiport devices.
For some mutexing purposes, each function is assigned their own
register. For other cases, each function is assigned its own request
and grant bits of a single register. For the latter cases, the tg3
driver is incorrectly allowing each function to use the same set of
grant / request bits. This patch fixes the code so that each function
uses the appropriate bitset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
be2net: Add detect UE feature for Lancer
be2net: Prevent CQ full condition for Lancer
be2net: Fix disabling multicast promiscous mode
be2net: Fix endian issue in RX filter command
af_packet: de-inline some helper functions
MAINTAINERS: Add can-gw include to maintained files
net: Add back alignment for size for __alloc_skb
net: add missing bh_unlock_sock() calls
l2tp: fix race in l2tp_recv_dequeue()
ixgbevf: Update release version
ixgbe: DCB, return max for IEEE traffic classes
ixgbe: fix reading of the buffer returned by the firmware
ixgbe: Fix compiler warnings
ixgbe: fix smatch splat due to missing NULL check
ixgbe: fix disabling of Tx laser at probe
ixgbe: Fix link issues caused by a reset while interface is down
igb: Fix for I347AT4 PHY cable length unit detection
e100: make sure vlan support isn't advertised on old adapters
e1000e: demote a debugging WARN to a debug log message
net: fix typo in drivers/net/ethernet/xilinx/ll_temac_main.c
...
Add code to detect UE in case of Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to HW that the CQ is cleaned up before posting new RX buffers.
This prevents the HW to go into CQ full error condition.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user tries to disable multicast promiscous mode, the adapter remains
in this mode as resetting the multicast promiscous mode was missing
in RX filter command. Fixed this.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpu_to_le32() for mcast_num field in RX filter command as this
field is of type u32.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning the max traffic classes on get requests simplifies
user space configurations because applications will know
explicitly how many traffic classes can be used.
Typical switch implementations use 2 or 3 traffic classes
so this not seen often today. And user space can learn
the number of traffic classes by return codes but this
allows user space to configure ixgbe correctly at the
start.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes some issues found in the buffer read portion of
ixgbe_host_interface_command()
- use `bi` as the buffer index counter instead of `i`
- add conversion to native cpu byte ordering on register read
- fix conversion from bytes to dword
- use dword_len instead of buf_len when reading the register
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wrap SR-IOV specific functions in CONFIG_PCI_IOV to avoid compiler
warnings.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_ieee_ets and ixgbe_ieee_pfc are intialized at
the same time. Do a check for both before configuring
IEEE802.1Qaz. Also max_frame was causing a sparse
warning resolved here as well.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
register_netdev() calls ndo_set_features() which may result in HW reset
which in turn will bring the laser back up.
This patch moves ixgbe_laser_tx_disable() below register_netdev()
in ixgbe_probe() to make sure laser is shut off on load.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Interface fails to obtain link on 82599 SFP in the following scenario:
1. Set advertised speed to GB:
ethtool -s eth0 advertise 0x20
2. Bring interface down
ip link set eth0 down
3. Issue any command that leads to a reset:
ethtool -t eth0
4. Bring link back up:
ip link set eth0 up
Following patch makes sure that the driver flaps the Tx laser every time
ixgbe_start_hw() is called, and not only when the speed is set.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY cable length unit detection was not using the correct
the correct PHY data variable for I347AT4.
Signed-off-by: Tomasz Kantecki <tomasz.kantecki@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e100 parts don't support vlan offload but they generally do
allow use of vlans in higher software layers via the 8021q module.
That said, there are a couple of really old revisions of e100
hardware that don't even allow the longer frame sizes
required for vlan use with standard MTU.
Use the VLAN_CHALLENGED flag to prevent vlan binding to these
devices.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: David Lamparter <equinox@diac24.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This debugging message was recently added but it does not need to be as
alarming as a WARN.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Says Andrew:
"60 patches. That's good enough for -rc1 I guess. I have quite a lot
of detritus to be rechecked, work through maintainers, etc.
- most of the remains of MM
- rtc
- various misc
- cgroups
- memcg
- cpusets
- procfs
- ipc
- rapidio
- sysctl
- pps
- w1
- drivers/misc
- aio"
* akpm: (60 commits)
memcg: replace ss->id_lock with a rwlock
aio: allocate kiocbs in batches
drivers/misc/vmw_balloon.c: fix typo in code comment
drivers/misc/vmw_balloon.c: determine page allocation flag can_sleep outside loop
w1: disable irqs in critical section
drivers/w1/w1_int.c: multiple masters used same init_name
drivers/power/ds2780_battery.c: fix deadlock upon insertion and removal
drivers/power/ds2780_battery.c: add a nolock function to w1 interface
drivers/power/ds2780_battery.c: create central point for calling w1 interface
w1: ds2760 and ds2780, use ida for id and ida_simple_get() to get it
pps gpio client: add missing dependency
pps: new client driver using GPIO
pps: default echo function
include/linux/dma-mapping.h: add dma_zalloc_coherent()
sysctl: make CONFIG_SYSCTL_SYSCALL default to n
sysctl: add support for poll()
RapidIO: documentation update
drivers/net/rionet.c: fix ethernet address macros for LE platforms
RapidIO: fix potential null deref in rio_setup_device()
RapidIO: add mport driver for Tsi721 bridge
...
Modify Ethernet addess macros to be compatible with BE/LE platforms
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Chul Kim <chul.kim@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: <stable@kernel.org> [2.6.39+]
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://github.com/rustyrussell/linux:
virtio-blk: use ida to allocate disk index
virtio: Add platform bus driver for memory mapped virtio device
virtio: Dont add "config" to list for !per_vq_vector
virtio: console: wait for first console port for early console output
virtio: console: add port stats for bytes received, sent and discarded
virtio: console: make discard_port_data() use get_inbuf()
virtio: console: rename variable
virtio: console: make get_inbuf() return port->inbuf if present
virtio: console: Fix return type for get_inbuf()
virtio: console: Use wait_event_freezable instead of _interruptible
virtio: console: Ignore port name update request if name already set
virtio: console: Fix indentation
virtio: modify vring_init and vring_size to take account of the layout containing *_event_idx
virtio.h: correct comment for struct virtio_driver
virtio-net: Use virtio_config_val() for retrieving config
virtio_config: Add virtio_config_val_len()
virtio-console: Use virtio_config_val() for retrieving config
Perform "echo test" when cmd queue stuck detected, somethime it will cause
calltrace. I am not sure how to fix it yet, just remove the action now until
find a better way to handle it.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver can spam the logs with "RX: Packet dropped" messages. These drops
originate from 1. a correpted PLCP, 2. decryption errors, and 3. packet
size underruns. Condition #3 logs a separate message, thus no dropped message
is needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Continue the init process even fail to enable msi
out_iounmap is no longer used, remove it
Reported-by: werner <w.landgraf@ru.ru>
Tested-by: werner <w.landgraf@ru.ru>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 2e30168b ("libertas: terminate scan when stopping interface")
adds cleanup code to lbs_eth_stop to call cfg80211_scan_done if there's
an outstanding cfg80211_scan_request. However, it assumes that the
scan request was allocated via the cfg80211 stack. Libertas has
its own internal allocation method, kept track of with
priv->internal_scan. This doesn't set scan_req->wiphy, amongst other
things, which results in hitting a BUG() when we call cfg80211_scan_done
on the request.
This provides a function to take care of the low-level scan_req cleanup
details. We simply call that to deal with finishing up scan requests.
The bug we were hitting was:
[ 964.321495] kernel BUG at net/wireless/core.h:87!
[ 964.329970] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 964.341963] pgd = dcf80000
...
[ 964.849998] 9fe0: 00000000 beb417b8 4018e280 401e822c 60000010 00000004 00000000 00000000
[ 964.865007] [<c003104c>] (__bug+0x1c/0x28) from [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c)
[ 964.895324] [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c) from [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas])
[ 964.895324] [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas]) from [<c03002a0>] (__dev_close_many+0x94/0xc4)
[ 964.918995] [<c03002a0>] (__dev_close_many+0x94/0xc4) from [<c030037c>] (dev_close_many+0x78/0xe0)
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes system hang when resuming from S3 state
and lower rate sens failure issue.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the driver did not care if TX_CTL_REQ_TX_STATUS
was set on aggregated frames or not and it would silently
drop successfully sent frames if possible [much like:
"no news is good news!"].
But, TX_CTL_REQ_TX_STATUS was invented for a reason and
no tx status report should ever be dropped if it is set.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit ce407afc10 introduced regression for AR9330/AR9340
register offsets. Some of the register offsets are common
for AR9330/AR9340/AR9485 except AR9380. Fix that.
Cc: stable@kernel.org [3.1.0+]
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My recent commits (3782c69d, 324c74a) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.
This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message
ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Stanislaw pointed out, my patch
iwlagn: fix a race in the unmapping of the TFDs
solved only part of the problem. The race still exists for TFDs of
the host commands. Fix that too.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
Commit 9e903e0852 ("net: add skb frag size accessors") used frag_size
instead of skb_frag_size in this file.
Fixes this build error:
drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit':
drivers/net/ethernet/xilinx/ll_temac_main.c:717:3: error: implicit declaration of function 'frag_size' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies virtio-net to use virtio_config_val() instead
of a 'if(virtio_has_feature()) vdev->config->get()' construct to retrieve
optional values from the config space.
Cc: Amit Shah <amit.shah@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Macintosh CS89x0 based ethernet cards use a Crystal Semiconductor (Now
Cirrus Logic) CS89x0 chip, so the mac89x0 driver should be in
drivers/net/ethernet/cirrus instead of drivers/net/ethernet/apple.
This also fixes a build problem, as the driver needs a header file from the
cirrus directory:
drivers/net/ethernet/apple/mac89x0.c:107:20: error: cs89x0.h: No such file or directory
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the SC92031 could be found on fake "Realtek" NICs, it has no
relationship to Realtek, and is actually from Silan.
Create a new subdirectory for silan and move sc92031 there.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zheng Liang(lzheng@redhat.com) found a bug that if we config bonding with
arp monitor, sometimes bonding driver cannot get the speed and duplex from
its slaves, it will assume them to be 100Mb/sec and Full, please see
/proc/net/bonding/bond0.
But there is no such problem when uses miimon.
(Take igb for example)
I find that the reason is that after dev_open() in bond_enslave(),
bond_update_speed_duplex() will call igb_get_settings()
, but in that function,
it runs ethtool_cmd_speed_set(ecmd, -1); ecmd->duplex = -1;
because igb get an error value of status.
So even dev_open() is called, but the device is not really ready to get its
settings.
Maybe it is safe for us to call igb_get_settings() only after
this message shows up, that is "igb: p4p1 NIC Link is Up 1000 Mbps Full Duplex,
Flow Control: RX".
So I prefer to update the speed and duplex for a slave when reseices
NETDEV_CHANGE/NETDEV_UP event.
Changelog
V2:
1 remove the "fake 100/Full" logic in bond_update_speed_duplex(),
set speed and duplex to -1 when it gets error value of speed and duplex.
2 delete the warning in bond_enslave() if bond_update_speed_duplex() returns
error.
3 make bond_info_show_slave() handle bad values of speed and duplex.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
mlx4_core: Deprecate log_num_vlan module param
IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
IB/mlx4: Enable 4K mtu for IBoE
RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
RDMA/cxgb4: Serialize calls to CQ's comp_handler
RDMA/cxgb3: Serialize calls to CQ's comp_handler
IB/qib: Fix issue with link states and QSFP cables
IB/mlx4: Configure extended active speeds
mlx4_core: Add extended port capabilities support
IB/qib: Hold links until tuning data is available
IB/qib: Clean up checkpatch issue
IB/qib: Remove s_lock around header validation
IB/qib: Precompute timeout jiffies to optimize latency
IB/qib: Use RCU for qpn lookup
IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
IB/qib: Decode path MTU optimization
IB/qib: Optimize RC/UC code by IB operation
IPoIB: Use the right function to do DMA unmap pages
RDMA/cxgb4: Use correct QID in insert_recv_cqe()
RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
...
The `#define filename' screws up the expansion of
DEFINE_DYNAMIC_DEBUG_METADATA:
drivers/net/ethernet/i825xx/3c505.c: In function 'send_pcb':
drivers/net/ethernet/i825xx/3c505.c:390: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:390: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c:436: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:435: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c: In function 'start_receive':
drivers/net/ethernet/i825xx/3c505.c:557: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:557: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c: In function 'receive_packet':
drivers/net/ethernet/i825xx/3c505.c:629: error: expected identifier before string constant
etc
So remove that #define and "open-code" it.
Cc: Philip Blundell <philb@gnu.org>
Cc: David Miller <davem@davemloft.net>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This 2nd batch of implicit module.h users only appeared when we
removed the unnecessary module.h from include/linux/miscdevice.h
[The 1st batch is already present in Greg's staging tree.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
For some reason three #include <linux/...> are buried way
down in the file. Since the inclusion of module.h is one
of them, the inclusion comes after use of EXPORT_SYMBOL
which will cause warnings about implicit declarations.
Relocate all the headers to the top.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It only has module_param and EXPORT_SYMBOL, so now that export.h
is in scope at the same time as the recent ath5k update, we can
delete this module.h include.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were using moduleparam infrastructure, but were not
including anything for it -- which is fine when module.h is being
implicitly included in all files, but that is going away.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c
This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Kalle Valo