Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.
This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.
Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issuing two consecutive scans you could often end up
getting in the logs:
"ath9k: Two wiphys trying to scan at the same time"
This message is due to a race in mac80211 but addressing
that race requires some more major changes on the driver
and perhaps optimizations on mac80211 like removing the
scan complete callback alltogether. Its too late to address
this this kernel release so supress the complaint and annotate
this needs fixing for later.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
base index is not used anymore and so remove it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The user ratekbs of MCS15 ShortGI is incorrect and can not be lesser
than MCS15 rate. This incorrect rate may affect switching to higher
rates as the rate control algorithm always finds MCS15 is better
than MCS15 ShortGI and results in lower throughput. Fix this by
feeding the correct user ratekbs for MCS15 ShortGI rate.
This issue affects 3 stream case very badly as the 3 stream rates are
not used at all once we scale down to MCS15 from 3 stream rates.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3 stream rate control support for AR938X family
chipsets which supports 3 streams.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace valid and valid_single_stream in rate table with bit masks
and reorganize the code so adding 3x3 rate control would be easier.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noisefloor array index always corresponds to the rx chain number it
belongs to (with an offset of 3 for the extension chain).
It's much simpler (and actually more correct) to directly use the
chainmask to calculate the bitmask for the noisefloor array, instead of
using these weird chip revision checks and hardcoded mask values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the noisefloor array, the extension channel values start at index 3
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the hardware is configured in HT20 mode, noise floor readings for
the extension channel often return invalid values, which keep the
values in the NF history buffer at the hardware-specific maximum limit.
Fix this by discarding the extension channel values when in HT20 mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an aggregation session is being cleaned up, while the tx status
for some frames is being processed, the TID is flushed and its buffers
are sent out.
Unfortunately that left the pending un-acked frames unprocessed, thus
leaking buffers. Fix this by reordering the code so that those frames
are processed first, before the TID is flushed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes txq state(txq->stopped) can be marked as started but the actual
queue may not be started (in ATH_WIPHY_SCAN state, for example). Fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The snprintf() function returns the number of characters that would have
been written (not counting the NUL character on the end). It could
potentially be larger than the size of the buffer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c:282:26: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/main.c:282:26: expected restricted __le16 [usertype] duration_id
drivers/net/wireless/ath/ath9k/main.c:282:26: got int
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An A-MPDU may contain several subframes each containing its own
CRC for the data. Each subframe also has a respective CRC for the
MPDU length and 4 reserved bits (aka delimeter CRC). AR9003 will
ACK frames that have a valid data CRC but have failed to pass the
CRC for the MPDU length, if and only if the subframe is not the
last subframe in an A-MPDU and if an OFDM phy OFDM reset error has
been caught. Discarding those subframes results in packet loss under
heavy stress conditions, an example being UDP video. Since the
frames are ACK'd by hardware we need to let these frames through
and process them as valid frames.
Cc: Tushit Jain <tushit.jain@atheros.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse complaint:
CHECK drivers/net/wireless/ath/ath9k/htc_drv_main.c
drivers/net/wireless/ath/ath9k/htc_drv_main.c:441:5:
warning: symbol 'ath9k_htc_tx_aggr_oper'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to documentation, The following chip revisions were never sold:
- AR9280 v1.0
- AR9285 v1.0
- AR9285 v1.1
- AR9287 v1.0
Removing initvals specific to these chip revisions saves around 30k in
binary size (tested on MIPS).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch 'ath9k: fix a buffer leak in A-MPDU completion' addressed the
issue of running out of buffers/descriptors in the tx path if a STA is
deleted while tx status feedback is still pending.
The remaining issue is that the skbs of the buffers are not reclaimed,
leaving a memory leak.
This patch fixes this issue by running the buffers through
ath_tx_complete_buf(), ensuring that the pending frames counter is also
updated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
num_sec_wiphy means max secondary wifis that the driver can accomudate.
So cancelling wiphy work should be based on the presence of
secondary wifis.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove tMinCalPower from ath9k_hw_set_def_power_cal_table(), as it's
never used. Remove corresponding arguments of the functions calculating
that value.
Original patch by Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED should be ON when the radio is put into FULL SLEEP mode during the idle
unassociated state.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:
- PHY registers for AR9003 are different
- AR9003 always uses 3 chains, earlier versions are more selective
- The AR9003 variant contains a fix for NF load timeouts
This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally the hardware can send out tx status information with the wrong
TID. In that case, the BA status cannot be trusted and the aggregate
must be retransmitted.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the receive path gets stuck, a full hardware reset is necessary to
recover from it. If this happens during a scan, the whole scan might fail,
as each channel change bypasses the full reset sequence.
Fix this by resetting the fast channel change flag if stopping the
receive path fails.
This will reduce the number of error messages that look like this:
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x40000020
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PDADC values were only generated for values surrounding the target
index, however not for the target index itself, leading to a minor
error in the generated curve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9285, the antenna switch configuration register uses more than just
16 bits. Because of an arbitrary mask applied to the EEPROM value that
stores this configuration, diversity was broken in some cases, leading
to a significant degradation in signal strength.
Fix this by changing the callback to return a 32 bit value and remove
the arbitrary mask.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_tx_complete_aggr() is called, it's responsible for returning
all buffers in the linked list. This was not done when the STA lookup
failed, leading to a race condition that could leak a few buffers when
a STA just disconnected.
Fix this by immediately returning all buffers to the free list in this case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like it might be possible for a TID to be paused, while still
holding some queued buffers, however ath_tx_node_cleanup currently only
iterates over active TIDs.
Fix this by always checking every allocated TID for the STA that is being
cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit eed8e22f01 added support for using
multicast key lookup to support per-vif/sta keys for AP and ad-hoc.
Unfortunately, it also introduced a crash in ad-hoc mode when the sta
pointer is NULL, which happens when setting up an interface with WEP
keys. This patch fixes it by falling back to the assigned key index.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_check_alive() occasionally returns false, as the hardware
is still processing data in a specific state. Fix this issue by
repeating the test a few times with longer delay inbetween attempts.
This gets rid of excessive hardware resets that appear frequently on
some AR9132 based devices, but could also happen on AR9280.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This includes the following changes/fixes:
- a bugfix for stuck beacon issues
- timing changes for improved performance
- AGC setting improvements
- fixes for high temperature issues on some chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This format is generated by the initval tool, available at:
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.
Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.
This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'bf_retries' field of the ath_buf structure was used for both
software retries (AMPDU subframes) and hardware retries (legacy
frames). This led to a wrong retry count being reported for the A-MPDU
rate control stats.
This patch changes the code to no longer use bf_retries for reporting
retry counts, but instead always using the real on-chip retry count
from the ath_tx_status.
Additionally, if the first subframe of an A-MPDU was not acked, the tx
status report is submitted along with the first acked subframe, which
may not contain the correct rates in the tx info.
This is easily corrected by saving the tx rate info before looping over
subframes, and then copying it back once the A-MPDU status report is
submitted.
In my tests this change improves throughput visibly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau