When based on the CCR_ENABLE bit the channel is stopped we should not call
omap_dma_callback(), only change the return value to DMA_COMPLETE. Client
drivers will do the right thing to clean up the channel after the transfer
has been completed.
Check the CCR_ENABLE only if the channel is running and not paused since
pause in sDMA means that the channel is stopped.
This will fix one hard to reproduce race condition when the channel is
terminated during transfer (affecting cyclic operation).
Fixes: 1a7cf7b26f ("dmaengine: omap-dma: Handle cases when the channel is polled for completion")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch extends the capabilities of the driver to handle DMA
transfers to and from devices of 1, 2, 4, 16 (for MPC512x), and 32 byte
widths.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the MPC8308 has no external request lines to initiate DMA transfers,
all transfers must be triggered by software.
Because of this, the current implementation of DMA transfers from and to
devices on MPC8308 SoCs using major and minor loops is faulty: After the
completion of the first major loop, the DMA engine resets the start flag in
the channel's TCD, thus halting the transfer. The driver would have to set
the start bit again to trigger the next iteration of the major loop; on
MPC512x SoCs, this is done via the external request lines, so in this case,
the driver doesn't have to interfer in any way.
This has the effect that on MPC8308s, every DMA transfer to or from a
device hangs after executing the first major loop.
The patch fixes this behavior by using just one major loop for the whole
DMA transfer on MPC8308s.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This tells, for example, IOMMU what the maximum size of a segment
the DMA controller can send.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The timeout capability is only available on the so called DMA write channels,
i.e. associated with UART Rx FIFO. It means we don't need to check the
direction of the channel to handle timeouts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current code allows only up to 3 descriptors to be programmed to the hardware
since it is used wrong calculations. Change % to min_t() to allow as many
descriptors as user supplied. At once it could be programmed up to 4
descriptors due to hardware limitations.
The issue was found under stress test, so it might not bother ordinary users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a typo in documentation regarding to descriptor empty bit (DESCE)
which is set to 1 when descriptor is empty. Thus, status register at the end of
a transfer usually returns all DESCE bits set and thus it will never be zero.
Moreover, there are 2 bits (CDESC) that encode current descriptor, on which
interrupt has been asserted. In case when we have few descriptors programmed we
might have non-zero value.
Remove DESCE and CDESC bits from DMA channel status register (HSU_CH_SR) when
reading it.
Fixes: 2b49e0c567 ("dmaengine: append hsu DMA driver")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit f0579c8cea ("dmaengine: hsu: speed up residue calculation")
speeded up calculation of the queued descriptor but broke the initial residue
value for active descriptor.
In accordance with documentation the hardware descriptor is updated each time
DMA transfered some bytes. It means we have to calculate a sum of lengths of
non-submitted hardware descriptors and whatever current values in the hardware.
Do this straightforward.
Fixes: f0579c8cea ("dmaengine: hsu: speed up residue calculation")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
HSU_CH_MTSR register should be programmed to a minimum size to transfer. This
size on a memory side of the transfer. Program it accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
According to dmaengine kerneldoc the struct dma_chan has always a non-NULL
pointer to DMA device and a test in dma_async_device_register()
validates that DMA device must also point to struct device.
All pr_ prints except one in dma_channel_table_init() have valid DMA
channel or DMA device pointer available which allow convert them to use
dev_ functions and thus able to show the associated DMA device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are only three patches this time, most other changes to
files in include/asm-generic tend to go through the tree of whoever
depends on the change.
Two patches are cleanups for stuff that is no longer needed,
the main change is to adapt the generic version of BUG_ON()
for CONFIG_BUG=n to make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings
about that undefined behavior in randconfig builds when
we keep going on after hitting a BUG_ON().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8tPL
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are only three patches this time, most other changes to files in
include/asm-generic tend to go through the tree of whoever depends on
the change.
Two patches are cleanups for stuff that is no longer needed, the main
change is to adapt the generic version of BUG_ON() for CONFIG_BUG=n to
make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings about
that undefined behavior in randconfig builds when we keep going on
after hitting a BUG_ON()"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove old nonatomic-io wrapper files
asm-generic: default BUG_ON(x) to if(x)BUG()
asm-generic: page.h: Remove useless get_user_page and free_user_page
Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP, uniphier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ynNj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP,
uniphier"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: uniphier: rework SMP code to support new System Bus binding
ARM: uniphier: add missing of_node_put()
ARM: at91: avoid defining CONFIG_* symbols in source code
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
dmaengine: pxa_dma: fix the maximum requestor line
ARM: alpine: select the Alpine MSI controller driver
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: s3c24xx: Avoid warning for inb/outb
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
...
This is smallish update with minor changes to core and new driver and usual
updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the mapping.
- We now expose the maxburst for slave dma as new capability so clients can
know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in progress
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wCCJ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is smallish update with minor changes to core and new driver and
usual updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the
mapping.
- We now expose the maxburst for slave dma as new capability so
clients can know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in
progress"
* tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
dmaengine: IOATDMA: revise channel reset workaround on CB3.3 platforms
dmaengine: add Qualcomm Technologies HIDMA channel driver
dmaengine: add Qualcomm Technologies HIDMA management driver
dmaengine: hidma: Add Device Tree binding
dmaengine: qcom_bam_dma: move to qcom directory
dmaengine: tegra: Move of_device_id table near to its user
dmaengine: xilinx_vdma: Remove unnecessary variable initializations
dmaengine: sirf: use __maybe_unused to hide pm functions
dmaengine: rcar-dmac: clear pertinence number of channels
dmaengine: sh: shdmac: don't open code of_device_get_match_data()
dmaengine: tegra: don't open code of_device_get_match_data()
dmaengine: qcom_bam_dma: Make driver work for BE
dmaengine: sun4i: support module autoloading
dma/mic_x100_dma: IS_ERR() vs PTR_ERR() typo
dmaengine: xilinx_vdma: Use readl_poll_timeout instead of do while loop's
dmaengine: xilinx_vdma: Simplify spin lock handling
dmaengine: xilinx_vdma: Fix issues with non-parking mode
dmaengine: xilinx_vdma: Improve SG engine handling
dmaengine: pl330: fix to support the burst mode
dmaengine: make slave address physical
...
Pull dma_*_writecombine rename from Ingo Molnar:
"Rename dma_*_writecombine() to dma_*_wc()
This is a tree-wide API rename, to move the dma_*() write-combining
APIs closer in name to their usual API families. (The old API names
are kept as compatibility wrappers to not introduce extra breakage.)
The patch was Coccinelle generated"
* 'mm-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dma, mm/pat: Rename dma_*_writecombine() to dma_*_wc()
Previously we unloaded the interrupts and reloaded in order to work around
a channel reset bug that cleared the MSIX table. This approach just isn't
practical when a reset needs to happen in the error handler that just
happens to be running in interrupt context (bottom half). It looks like we
can work around the hardware issue by just storing a shadow copy of the
MSIX table and restore it after reset.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for hidma engine. The driver consists of two
logical blocks. The DMA engine interface and the low-level interface.
The hardware only supports memcpy/memset and this driver only support
memcpy interface. HW and driver doesn't support slave interface.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Qualcomm Technologies HIDMA device has been designed to support
virtualization technology. The driver has been divided into two to follow
the hardware design.
1. HIDMA Management driver
2. HIDMA Channel driver
Each HIDMA HW consists of multiple channels. These channels share some set
of common parameters. These parameters are initialized by the management
driver during power up. Same management driver is used for monitoring the
execution of the channels. Management driver can change the performance
behavior dynamically such as bandwidth allocation and prioritization.
The management driver is executed in host context and is the main
management entity for all channels provided by the device.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Creating a QCOM directory for all QCOM DMA source files.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When computing the residue we need two pieces of information: the current
descriptor and the remaining data of the current descriptor. To get
that information, we need to read consecutively two registers but we
can't do it in an atomic way. For that reason, we have to check manually
that current descriptor has not changed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Suggested-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reported-by: David Engraf <david.engraf@sysgo.com>
Tested-by: David Engraf <david.engraf@sysgo.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
adding unmap of sources and destinations while doing dequeue.
Signed-off-by: Xuelin Shi <xuelin.shi@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After using the function of_device_get_match_data(), the
of_device_id table for tegra20 dma is not used by probe()
and hence moving it near to place where platform driver is
defined as this table used only on this data structure.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch removes the unnecessary variable initializations
in the driver.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sirf dma driver uses #ifdef to check for CONFIG_PM_SLEEP
for its suspend/resume code but then has no #ifdef for the
respective runtime PM code, so we get a warning if CONFIG_PM
is disabled altogether:
drivers/dma/sirf-dma.c:1000:12: error: 'sirfsoc_dma_runtime_resume' defined but not used [-Werror=unused-function]
This removes the existing #ifdef and instead uses __maybe_unused
annotations for all four functions to let the compiler know it
can silently drop the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMACHCLR clears each channels, but its channel number is based on
its SoC or IP. Current driver is using fixed 0x7fff (= for 15ch),
it is not good match for Gen3 or Gen2 Audio DMAC. This patch fixes it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use of_device_get_match_data() for getting matched data
instead of implementing this locally.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the Qualcomm BAM dmaenging driver to work with big
endian kernels.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
MODULE_DEVICE_TABLE() is missing, so the module isn't auto-loading on
supported systems. This commit adds the missing line so it loads
automatically when building it as a module and running on a system
with the early sunxi DMA engine.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is harmless because the caller only cares about zero vs non-zero
but we should be returning PTR_ERR() here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
While testing audio with pxa2xx-ac97, underrun were happening while the
user application was correctly feeding the music. Debug proved that the
cyclic transfer is not cyclic, ie. the last descriptor did not loop on
the first.
Another issue is that the descriptor length was always set to 8192,
because of an trivial operator issue.
This was tested on a pxa27x platform.
Fixes: a57e16cf03 ("dmaengine: pxa: add pxa dmaengine driver")
Reported-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is sometimes necessary to poll a memory-mapped register until its
value satisfies some condition use convenience macros
that do this instead of do while loop's.
This patch updates the same in the driver.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch simplifies the spin lock handling in the driver
by moving locking out of xilinx_dma_start_transfer() API
and xilinx_dma_update_completed_cookie() API.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes issues with the Non-parking mode(Cirular mode).
With the existing driver in cirular mode if we submit frames less than h/w
configured we simply end-up having misconfigured vdma h/w.
This patch fixes this issue by configuring the frame count register.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current driver allows user to queue up multiple segments
on to a single transaction descriptor. User will submit this single desc
and in the issue_pending() we decode multiple segments and submit to SG HW engine.
We free up the allocated_desc when it is submitted to the HW.
Existing code prevents the user to prepare multiple trasactions at same time as
we are overwrite with the allocated_desc.
The best utilization of HW SG engine would happen if we collate the pending
list when we start dma this patch updates the same.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The two header files got moved to include/linux, and most
users were already converted, this changes the remaining drivers
and removes the files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
This patch fixes the burst mode that will break DMA uart on SoCFPGA.
In some cases, some SoCS didn't support the multi-burst
even if the devices who use the pl330 claim support the maxburst.
Fixes: commit 848e977
"dmaengine: pl330: support burst mode for dev-to-mem and mem-to-dev transmit"
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current number of requestor lines is limited to 31. This was an
error of a previous commit, as this number is platform dependent, and is
actually :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines
The previous testing did not reveal the faulty constant as on pxa[23]xx
platforms, only camera, MSL and USB are above requestor 32, and in these
only the camera has a driver using dma.
Fixes: e87ffbdf06 ("dmaengine: pxa_dma: fix the no-requestor case")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vinod Koul <vinod.koul@intel.com>
In acpi_dma_request_slave_chan_by_name() the debug message is printed before
the actual matching happens. Correct the message itself to be in align with the
flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a typo in the definition of IDMA64C_CFGH_WR_ISSUE_THD(x). Fix it by
swapping characters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mxs-dma unit is also available on i.MX6UL. Make it possible to
select it in Kconfig.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to avoid possible race condition when client drivers are using
dmaengine_terminate_sync() call to disable the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need the callback to support the dmaengine_terminate_sync().
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need the callback to support the dmaengine_terminate_sync().
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Future IOATDMA hardware will take advantage of descriptors residing in
contiguous memory. Setting the descriptor ring in max config DMA memory
of 2MB. Each channel will need 2 of these chunks. This should provide 64k
of 64B descriptors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Moving to contingous memory backed descriptor rings. This makes is really
difficult and complex to do reshape. Going to remove this as I don't think
we need to do it anymore.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Converting old pci_pool_* calls to "new" dma_pool_* to make everything
uniform.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 2895b2cad6 ("dmaengine: dw: fix cyclic transfer callbacks")
re-enabled BLOCK interrupts with regard to make cyclic transfers work. However,
this change becomes a regression for non-cyclic transfers as interrupt counters
under stress test had been grown enormously (approximately per 4-5 bytes in the
UART loop back test).
Taking into consideration above enable BLOCK interrupts if and only if channel
is programmed to perform cyclic transfer.
Fixes: 2895b2cad6 ("dmaengine: dw: fix cyclic transfer callbacks")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The datasheet requires that the user must clear LLP_[SD]_EN bits whenever
LLP.LOC is zero, i.e. in the last descriptor of a multi-block chain.
Make the driver do this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add max burst capability for dmaengine and
limit burst capability to one for PL330_QUIRK_BROKEN_NO_FLUSHP
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add max_burst to dma_get_slave_caps for clients
to get the burst capability of slave dma controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add "arm,pl330-broken-no-flushp" quirk to avoid execute
DMAFLUSHP if Soc doesn't support it.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Doug Anderson <dianders@chromium.org>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds to support burst mode for dev-to-mem and
mem-to-dev transmit.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Doug Anderson <dianders@chromium.org>
cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When retrieving the residue value, the SRC/DST fields of the
active PaRAM are read to determine the current position of
the DMA engine. However, the AM335x Technical Reference Manual
states:
11.3.3.6 Parameter Set Updates
After the TR is read from the PaRAM (and is in the process
of being submitted to the EDMA3TC), the following fields are
updated as needed: ... SRC DST
This means SRC/DST is incremented even though the DMA transfer
may not have started yet or is in progress. Thus if the reader
of the residue accesses the DMA buffer too quickly, the CPU is
misinformed about the data that has been successfully processed.
The CCSTAT.ACTV register is a boolean that is set if any TR is
being processed by either the EMDA3CC or EDMA3TC. By polling
this register it is possible to ensure that the residue value
returned is valid for immediate processing. However, since the
DMA engine may be active, polling may never hit a moment where
no TR is being processed. To handle this, the SRC/DST is also
polled to see if it changes. And as a last resort, a max loop
count for the busy waiting exists to avoid an infinite loop.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
WildcatPoint PCH as seen on MacBook 12-inch (Early 2015) has PCI enabled
DesignWare DMA controller. Enable it by adding its ID to the corresponding
driver.
Reported-by: Leif Liddy <leif.liddy@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=110901
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The timer_event() function seems to have a bug where it ends up marking the
last entry as non-responding and eventually attempts to restart the
channel. This also continuously happen when idle. What needs to happen is
for us to make sure there are no descriptors active and then handle that
case properly. We should only hit the "cleanup" stage if there are still
active descriptors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
CC [M] drivers/dma/ioat/prep.o
drivers/dma/ioat/prep.c: In function 'ioat_prep_pqxor':
drivers/dma/ioat/prep.c:682:1: warning: the frame size of 1048 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
drivers/dma/ioat/prep.c: In function 'ioat_prep_pqxor_val':
drivers/dma/ioat/prep.c:714:1: warning: the frame size of 1048 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
gcc version 5.3.1 20151219 (Ubuntu 5.3.1-4ubuntu1)
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Debugging ALSA hangups it was found that EP9302 (latest E2 rev.) DMA controller
sometimes asserts STALL interrupt instead of NFB interrupt. Simply ignoring the
difference and simply acting upon the amount of data we still have to transfer
seems to work fine. This somehow sounds similar to M2M issue which is already
dealt with in the driver, when the controller asserts DONE interrupt too early.
The issue is not documented in Cirrus Logic erratas for EP93XX, but original
Cirrus DMA driver from 2003 (not based on DMA API) did the similar handling
of STALL interrupt. In-tree driver (6d831c65) did it also, before conversion to
DMA engine API.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The offset of SINC should be 9, not 7, here fix this
typo.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Few fixes on drivers have piled up and one missed rcar bindings patch
which got somehow lost in for-linus branch so cherry-picked that one
Fixes are on dw, at_hdmac, edma
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWn3/rAAoJEHwUBw8lI4NHfFEP/3YTyj1BganEuV//h81l16Nl
fbgFtvgAZ5rilakOmsQJZ1Pp1r3aGgT8nULaBU/qtD2Ye0Ox0lQol/KfpnUDWH1a
go6yYnsArUJxs35QPCDV6WUnopzlDTLnamE7C/VcjQsLokJBEv4PubFKhQd6IFvB
mx8N0Rnn3oyhcAMADtUDnPljBgyPo1dwXbwM5IxlYI9Ar8zsT4hLMCHxXad7SzRR
SvRXMRflDlIxKwKh1f/4FnQ9BTW2mKb3nypBG6Uz8YatIPHliJO8LVjmvYsGA2KU
JtjDIpsRCeqETEPKlTSt6nQKdghR2CapDNEIS7Cv4LZFvCL3ADJL17xAfMKaxdkO
m4aVpK6vR+h/e0csYE0GYkcPugXAvm89MWHDkywmqo4CtCgh7QbMYxXR4MNsy3xS
TGHU2BkULrKoZkcKDKkXEB6fvfsMtzdd33/P0KPf2i0WcZUDo1jmETDLpz1Vehf6
hcRHURYMqHG/zJLItwQsAcJgfQtp+3oeiBv+N3FRjY/ECFPQWShFM5kVqac0Jr9y
e8gnC1+p7IfOesaHO/FUW5KvvWnQ1gskUFbtM0cZNGGqhiKTjx8lnWnXH530SU9D
Nf/bgNsQMoD3h5Uqsrsf5X6e+CNIGSqit9tONSqHSHG8POVCNo8CAkfj/sc7Ck+s
LH8N8eM3UIKsTojVbjMn
=16UM
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Here is my second pull request for this window:
A few driver fixes have piled up and one missed rcar bindings patch
which got somehow lost in for-linus branch so cherry-picked that one.
Fixes are for dw, at_hdmac, edma"
* tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: rcar-dmac: Document SoC specific bindings
dmaengine: at_xdmac: fix resume for cyclic transfers
dmaengine: dw: fix cyclic transfer callbacks
dmaengine: dw: fix cyclic transfer setup
dmaengine: edma: Fix paRAM slot allocation for entry channel 0
When having cyclic transfers, the channel was paused when performing
suspend but was not correctly resumed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: <stable@vger.kernel.org> # 4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We've had quite busy weeks in this cycle. Looking at ALSA core, the
significant changes are a few fixes wrt timer and sequencer ioctls
that have been revealed by fuzzer recently. Other than that, ASoC
core got a few updates about DAI link handling, but these are rather
straightforward refactoring.
In drivers scene, ASoC received quite lots of new drivers in addition
to bunch of updates for still ongoing Intel Skylake support and
topology API. HD-audio gained a new HDMI/DP hotplug notification via
component. FireWire got a pile of code refactoring/updates with
SCS.1x driver integration.
More highlights are shown below.
[NOTE: this contains also many commits for DRM. This is due to the
pull of drm stable branch into sound tree, as the base of i915 audio
component work for HD-audio. The highlights below don't contain
these DRM changes, as these are supposed to be pulled via drm tree in
anyway sooner or later.]
Core
- Handful fixes to harden ALSA timer and sequencer ioctls against
races reported by syzkaller fuzzer
- Irq description string can be unique to each card; only for
HD-audio for now
ASoC
- Conversion of the array of DAI links to a list for supporting
dynamically adding and removing DAI links
- Topology API enhancements to make everything more component based
and being able to specify PCM links via topology
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production; we really need to get to the
point where that can be done
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come
- Lots of new features and cleanups for the Renesas drivers
- ANC support for WM5110
- New drivers: Imagination Technologies IPs, Atmel class D speaker,
Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and
RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP
- Rename PCM1792a driver to be generic pcm179x
HD-Audio
- Use audio component for i915 HDMI/DP hotplug handling
- On-demand binding with i915 driver
- bdl_pos_adj parameter adjustment for Baytrail controllers
- Enable power_save_node for CX20722; this shouldn't lead to
regression, hopefully
- Kabylake HDMI/DP codec support
- Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell
machines
- A few code refactoring
FireWire
- Lots of code cleanup and refactoring
- Integrate the support of SCS.1x devices into snd-oxfw driver;
snd-scs1x driver is obsoleted
USB-audio
- Fix possible NULL dereference at disconnection
- A regression fix for Native Instruments devices
Misc
- A few code cleanups of fm801 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Gvgb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We've had quite busy weeks in this cycle. Looking at ALSA core, the
significant changes are a few fixes wrt timer and sequencer ioctls
that have been revealed by fuzzer recently. Other than that, ASoC
core got a few updates about DAI link handling, but these are rather
straightforward refactoring.
In drivers scene, ASoC received quite lots of new drivers in addition
to bunch of updates for still ongoing Intel Skylake support and
topology API. HD-audio gained a new HDMI/DP hotplug notification via
component. FireWire got a pile of code refactoring/updates with
SCS.1x driver integration.
More highlights are shown below.
[ NOTE: this contains also many commits for DRM. This is due to the
pull of drm stable branch into sound tree, as the base of i915 audio
component work for HD-audio. The highlights below don't contain
these DRM changes, as these are supposed to be pulled via drm tree
in anyway sooner or later. ]
Core:
- Handful fixes to harden ALSA timer and sequencer ioctls against
races reported by syzkaller fuzzer
- Irq description string can be unique to each card; only for
HD-audio for now
ASoC:
- Conversion of the array of DAI links to a list for supporting
dynamically adding and removing DAI links
- Topology API enhancements to make everything more component based
and being able to specify PCM links via topology
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production; we really need to get to the
point where that can be done
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come
- Lots of new features and cleanups for the Renesas drivers
- ANC support for WM5110
- New drivers: Imagination Technologies IPs, Atmel class D speaker,
Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and
RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP
- Rename PCM1792a driver to be generic pcm179x
HD-Audio:
- Use audio component for i915 HDMI/DP hotplug handling
- On-demand binding with i915 driver
- bdl_pos_adj parameter adjustment for Baytrail controllers
- Enable power_save_node for CX20722; this shouldn't lead to
regression, hopefully
- Kabylake HDMI/DP codec support
- Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell
machines
- A few code refactoring
FireWire:
- Lots of code cleanup and refactoring
- Integrate the support of SCS.1x devices into snd-oxfw driver;
snd-scs1x driver is obsoleted
USB-audio:
- Fix possible NULL dereference at disconnection
- A regression fix for Native Instruments devices
Misc:
- A few code cleanups of fm801 driver"
* tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (722 commits)
ALSA: timer: Code cleanup
ALSA: timer: Harden slave timer list handling
ALSA: hda - Add fixup for Dell Latitidue E6540
ALSA: timer: Fix race among timer ioctls
ALSA: hda - add codec support for Kabylake display audio codec
ALSA: timer: Fix double unlink of active_list
ALSA: usb-audio: Fix mixer ctl regression of Native Instrument devices
ALSA: hda - fix the headset mic detection problem for a Dell laptop
ALSA: hda - Fix white noise on Dell Latitude E5550
ALSA: hda_intel: add card number to irq description
ALSA: seq: Fix race at timer setup and close
ALSA: seq: Fix missing NULL check at remove_events ioctl
ALSA: usb-audio: Avoid calling usb_autopm_put_interface() at disconnect
ASoC: hdac_hdmi: remove unused hdac_hdmi_query_pin_connlist
ASoC: AMD: Add missing include file
ALSA: hda - Fixup inverted internal mic for Lenovo E50-80
ALSA: usb: Add native DSD support for Oppo HA-1
ASoC: Make aux_dev more like a generic component
ASoC: bcm2835: cleanup includes by ordering them alphabetically
ASoC: AMD: Manage ACP 2.x SRAM banks power
...
Cyclic transfer callbacks rely on block completion interrupts which were
disabled in commit ff7b05f29f ("dmaengine/dw_dmac: Don't handle block
interrupts"). This re-enables block interrupts so the cyclic callbacks
can work. Other transfer types are not affected as they set the INT_EN
bit only on the last block.
Fixes: ff7b05f29f ("dmaengine/dw_dmac: Don't handle block interrupts")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Commit 61e183f830 ("dmaengine/dw_dmac: Reconfigure interrupt and
chan_cfg register on resume") moved some channel initialisation to
a new function which must be called before starting a transfer.
This updates dw_dma_cyclic_start() to use dwc_dostart() like the other
modes, thus ensuring dwc_initialize() gets called and removing some code
duplication.
Fixes: 61e183f830 ("dmaengine/dw_dmac: Reconfigure interrupt and chan_cfg register on resume")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
This round we have few new features, new driver and updates to few drivers.
The new features to dmaengine core are:
- Synchronized transfer termination API to terminate the dmaengine
transfers in synchronized and async fashion as required by users.
We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac
drivers.
- Universal API for channel request and start consolidation of request
flows. It's user is ompa-dma driver.
- Introduce reuse of descriptors and use in pxa_dma driver
Add/Remove:
- STM32 DMA driver
- Removal of unused R-Car HPB-DMAC driver
Updates:
- ti-dma-crossbar updates for supporting eDMA
- tegra-apb pm updates
- idma64
- mv_xor updates
- ste_dma updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D5Fb
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This round we have few new features, new driver and updates to few
drivers.
The new features to dmaengine core are:
- Synchronized transfer termination API to terminate the dmaengine
transfers in synchronized and async fashion as required by users.
We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac
drivers.
- Universal API for channel request and start consolidation of
request flows. It's user is ompa-dma driver.
- Introduce reuse of descriptors and use in pxa_dma driver
Add/Remove:
- New STM32 DMA driver
- Removal of unused R-Car HPB-DMAC driver
Updates:
- ti-dma-crossbar updates for supporting eDMA
- tegra-apb pm updates
- idma64
- mv_xor updates
- ste_dma updates"
* tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (54 commits)
dmaengine: mv_xor: add suspend/resume support
dmaengine: mv_xor: de-duplicate mv_chan_set_mode*()
dmaengine: mv_xor: remove mv_xor_chan->current_type field
dmaengine: omap-dma: Add support for DMA filter mapping to slave devices
dmaengine: edma: Add support for DMA filter mapping to slave devices
dmaengine: core: Introduce new, universal API to request a channel
dmaengine: core: Move and merge the code paths using private_candidate
dmaengine: core: Skip mask matching when it is not provided to private_candidate
dmaengine: mdc: Correct terminate_all handling
dmaengine: edma: Add probe callback to edma_tptc_driver
dmaengine: dw: fix potential memory leak in dw_dma_parse_dt()
dmaengine: stm32-dma: Fix unchecked deference of chan->desc
dmaengine: sh: Remove unused R-Car HPB-DMAC driver
dmaengine: usb-dmac: Document SoC specific compatibility strings
ste_dma40: Delete an unnecessary variable initialisation in d40_probe()
ste_dma40: Delete another unnecessary check in d40_probe()
ste_dma40: Delete an unnecessary check before the function call "kmem_cache_destroy"
dmaengine: tegra-apb: Free interrupts before killing tasklets
dmaengine: tegra-apb: Update driver to use GFP_NOWAIT
dmaengine: tegra-apb: Only save channel state for those in use
...
edma_alloc_slot was not checking the channel mapping support existence when
slot 0 has been requested (used as entry slot for channel/event 0).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
Since we have a work around to prevent a system hangup we don't need to provide
a platform data explicitly anymore.
This reverts commit 175267b389.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to bother the hardware when all channels are idle. We have not
to get any interrupts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have to call dw_dma_disable() to stop any ongoing transfer. On some
platforms we can't do that since DMA device is powered off. Moreover we have no
possibility at that point to check if the platform is affected or not. That's
why we call pm_runtime_get_sync() / pm_runtime_put() unconditionally. On the
other hand we can't use pm_runtime_suspended() because runtime PM framework is
not fully used by the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For interrupt controller that doesn't support irq_disable and hardware
with level interrupt, an extra interrupt can be pending. This patch fixes
the issue by setting IRQ_DISABLE_UNLAZY flag for the interrupt line.
Reference: http://git.kernel.org/tip/e9849777d0e27cdd2902805be51da73e7c79578c
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This commit adds suspend/resume support to the mv_xor driver. The
config and interrupt mask registers must be saved and restored, and
upon resume, the MBus windows configuration must also be done again.
Tested on Armada 388 GP, with a RAID 5 array, accessed before and
after a suspend to RAM cycle.
Based on work from Ofer Heifetz and Lior Amsalem.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When commit 6f166312c6 ("dmaengine: mv_xor: add support for a38x
command in descriptor mode") added support for the descriptor mode
available in Marvell Armada 38x and later SoCs, it added a new
function mv_chan_set_mode_to_desc() which allows to configure a XOR
channel to get the specific operation to be done from each individual
DMA descriptor.
However, this function was mainly a duplicate of the existing
mv_chan_set_mode(), with just the operation being different.
This commit re-organizes the code into a single mv_chan_set_mode()
function, which takes the operation mode as argument, and the
mv_xor_channel_add() function decides whether to use
XOR_OPERATION_MODE_IN_DESC or XOR_OPERATION_MODE_XOR.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since commit 3e4f52e2da ("dma: mv_xor: Simplify the DMA_MEMCPY
operation"), this field is no longer used, so get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit e958e079e2 ("dmaengine: mic_x100: add missing
spin_unlock").
The above patch is incorrect. There is nothing wrong with the original
code. The spin_lock is acquired in the "prep" functions and released
in "submit".
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for providing device to filter_fn mapping so client drivers
can switch to use the dma_request_chan() API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for providing device to filter_fn mapping so client drivers
can switch to use the dma_request_chan() API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The two API function can cover most, if not all current APIs used to
request a channel. With minimal effort dmaengine drivers, platforms and
dmaengine user drivers can be converted to use the two function.
struct dma_chan *dma_request_chan_by_mask(const dma_cap_mask_t *mask);
To request any channel matching with the requested capabilities, can be
used to request channel for memcpy, memset, xor, etc where no hardware
synchronization is needed.
struct dma_chan *dma_request_chan(struct device *dev, const char *name);
To request a slave channel. The dma_request_chan() will try to find the
channel via DT, ACPI or in case if the kernel booted in non DT/ACPI mode
it will use a filter lookup table and retrieves the needed information from
the dma_slave_map provided by the DMA drivers.
This legacy mode needs changes in platform code, in dmaengine drivers and
finally the dmaengine user drivers can be converted:
For each dmaengine driver an array of DMA device, slave and the parameter
for the filter function needs to be added:
static const struct dma_slave_map da830_edma_map[] = {
{ "davinci-mcasp.0", "rx", EDMA_FILTER_PARAM(0, 0) },
{ "davinci-mcasp.0", "tx", EDMA_FILTER_PARAM(0, 1) },
{ "davinci-mcasp.1", "rx", EDMA_FILTER_PARAM(0, 2) },
{ "davinci-mcasp.1", "tx", EDMA_FILTER_PARAM(0, 3) },
{ "davinci-mcasp.2", "rx", EDMA_FILTER_PARAM(0, 4) },
{ "davinci-mcasp.2", "tx", EDMA_FILTER_PARAM(0, 5) },
{ "spi_davinci.0", "rx", EDMA_FILTER_PARAM(0, 14) },
{ "spi_davinci.0", "tx", EDMA_FILTER_PARAM(0, 15) },
{ "da830-mmc.0", "rx", EDMA_FILTER_PARAM(0, 16) },
{ "da830-mmc.0", "tx", EDMA_FILTER_PARAM(0, 17) },
{ "spi_davinci.1", "rx", EDMA_FILTER_PARAM(0, 18) },
{ "spi_davinci.1", "tx", EDMA_FILTER_PARAM(0, 19) },
};
This information is going to be needed by the dmaengine driver, so
modification to the platform_data is needed, and the driver map should be
added to the pdata of the DMA driver:
da8xx_edma0_pdata.slave_map = da830_edma_map;
da8xx_edma0_pdata.slavecnt = ARRAY_SIZE(da830_edma_map);
The DMA driver then needs to configure the needed device -> filter_fn
mapping before it registers with dma_async_device_register() :
ecc->dma_slave.filter_map.map = info->slave_map;
ecc->dma_slave.filter_map.mapcnt = info->slavecnt;
ecc->dma_slave.filter_map.fn = edma_filter_fn;
When neither DT or ACPI lookup is available the dma_request_chan() will
try to match the requester's device name with the filter_map's list of
device names, when a match found it will use the information from the
dma_slave_map to get the channel with the dma_get_channel() internal
function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Channel matching with private_candidate() is used in two paths, the error
checking is slightly different in them and they are duplicating code also.
Move the code under find_candidate() to provide consistent execution and
going to allow us to reuse this mode of channel lookup later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If mask is NULL skip the mask matching against the DMA device capabilities.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use of the CANCEL bit in mdc_terminate_all creates an
additional 'command done' to appear in the registers (in
addition to an interrupt).
In addition, there is a potential race between
mdc_terminate_all and the irq handler if a transfer
completes at the same time as the terminate all (presently
this results in an inappropriate warning).
To handle these issues, any outstanding 'command done'
events are cleared during mdc_terminate_all and the irq
handler takes no action when there are no new 'command done'
events.
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Due to changes in device and platform code drivers w/o probe will fail to
load. This means that the devices for eDMA TPTCs are goign to be without
driver and omap hwmod code will turn them off after the kernel finished
loading:
[ 3.015900] platform 49800000.tptc: omap_device_late_idle: enabled but no driver. Idling
[ 3.024671] platform 49a00000.tptc: omap_device_late_idle: enabled but no driver. Idling
This will prevent eDMA to work since the TPTCs are not enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Fixes: 34635b1acc ("dmaengine: edma: Add dummy driver skeleton for edma3-tptc")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the "dma-channels" DT property is missing, the dw_dma_parse_dt()
function return NULL, but not before allocating memory for a struct
dw_dma_platform_data through devres. If the device supports parameter
detection, the probe still succeeds and the allocated memory is not
released until the device is removed.
Fix this by deferring the allocation until after checking the
"dma-channels" property.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes at_xdmac_prep_dma_memcpy(). Indeed the data width field
of the Channel Configuration register was not updated properly in the
loop: the bits of the dwidth field were not cleared before adding their
new value.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
'commit d8b468394f ("dmaengine: Add STM32 DMA driver")' leads to the
following Smatch complaint:
drivers/dma/stm32-dma.c:562 stm32_dma_issue_pending()
error: we previously assumed 'chan->desc' could be null (see line 560)
So, this patch fixes the unchecked dereference of chan->desc by returning
operation not permitted error when stm32_dma_start_transfer() does not
succeed to allocate a virtual channel descriptor.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As of commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), the Renesas R-Car HPB-DMAC driver is no longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that requires
adding DT support to the driver, which is not planned.
Remove the driver, it can be resurrected from git history when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The variable "res" will eventually be set to a resource pointer from
a call of the d40_hw_detect_init(() function.
Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A single jump label was used by the d40_probe() function in several cases
for error handling which was a bit inefficient here.
* This implementation detail could be improved by the introduction
of another jump label.
* Remove an extra check for the variable "base".
* Omit its explicit initialisation at the beginning then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The kmem_cache_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On probe failure or driver removal, before killing any tasklets, ensure
that the channel interrupt is freed to ensure that another channel
interrupt cannot occur and schedule the tasklet again.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The tegra20-apb-dma driver currently uses the flag GFP_ATOMIC when
allocating memory for structures used in conjunction with the DMA
descriptors. It is preferred that dmaengine drivers use GFP_NOWAIT
instead and so the emergency memory pool will not be used by these
drivers.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the tegra-apb DMA driver suspend/resume helpers, save and
restore the registers for all channels regardless of whether they are
in use or not. Change this so that only channels that have been
allocated and configured are saved and restored.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Newer tegra devices have a separate word count register per channel that
contains the number of words to be transferred. This register is not
saved or restored by the suspend/resume helpers for these newer devices
and so ensure that it is.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the tegra_dma_runtime_suspend/resume functions, the pdev structure
is not needed, and so just call dev_get_drvdata() to get the device
data structure.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The tegra-apb DMA driver enables runtime-pm but never calls
pm_runtime_get/put and hence the runtime-pm callbacks are never invoked.
The driver manages the clocks by directly calling clk_prepare_enable()
and clk_unprepare_disable().
Fix this by replacing the clk_prepare_enable() and clk_disable_unprepare()
with pm_runtime_get_sync() and pm_runtime_put(), respectively. Note that
the consequence of this is that if runtime-pm is disabled, then the clocks
will remain on the entire time the driver is loaded. However, if
runtime-pm is disabled, then power is not most likely not a concern.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
spin lock should be released while returning from function
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Calling synchronize_irq() right before devm_free_irq() is quite useless. On
one hand the IRQ can easily fire again before devm_free_irq() is entered,
on the other hand devm_free_irq() itself calls synchronize_irq() internally
(in a race condition free way), before any state associated with the IRQ is
freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq, dev;
@@
-synchronize_irq(irq);
devm_free_irq(dev, irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This add power management suspend/resume support for the fsl-edma
driver.
eDMA acted as a basic function used by others. What it needs to do
is the two steps below to support power management.
In fsl_edma_suspend_late:
Check whether the DMA chan is idle, if it is not idle disable DMA
request.
In fsl_edma_resume_early:
Enable the eDMA and wait for being used.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
f931782917 dmaengine: bcm2835-dma: Fix memory leak when stopping a
running transfer
Fixed the memleak, but introduced another issue: the terminate_all callback
might be called with interrupts disabled and the dma_free_coherent() is
not allowed to be called when IRQs are disabled.
Convert the driver to use dma_pool_* for managing the list of control
blocks for the transfer.
Fixes: f931782917 ("dmaengine: bcm2835-dma: Fix memory leak when stopping a running transfer")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When performing interleaved transfers with numf > 1, an extra line is
copied. The mbr.bc field is incremented once too often. The length of
the block is (BLEN+1) microblocks.
Signed-off-by: Sylvain ETIENNE <Sylvain.ETIENNE@ingenico.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 4e5385784e ("dmaengine: at_xdmac: handle numf > 1")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code was not in agreement with the comments.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.3 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to calculate an overall length of the descriptor each time we
call for DMA transfer status. Instead we do this at descriptor allocation stage
and keep the stored length for further usage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the match DMA controller is done only for lower 32 bits of
address which might be not true on 64-bit platform. Check upper portion
as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since a local variable contains the number of hardware desriptors at the
beginning of idma64_desc_fill() we may use it to index the last descriptor as
well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Explicitly show in idma64_desc_fill() how we link the hardware
descriptors.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This tells, for example, IOMMU what the maximum size of a segment
the DMA controller can send.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to disable interrupts in the IRQ handler. The driver
guarantess that at one time only one descriptor is active, besides the fact
that each call to the same channel will be serialized in idma64_chan_irq()
handler anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix typo in a macro which was not used until now. It explains why there
is no error at compilation time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 "dmaengine: at_xdmac: creation of the atmel eXtended
DMA Controller driver"
Cc: stable@vger.kernel.org # 3.19 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When setting the channel configuration register, the perid field is not
set to 0 since it is useless for mem2mem transfers. Unfortunately, a
device has 0 as perid. It could cause spurious flags status because
the controller could mix some events from the two channels.
For that reason, use the highest perid value for mem2mem transfers since it
doesn't match the perid of other devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes an issue that list_for_each_entry() in
usb_dmac_chan_terminate_all() is possible to cause endless loop because
this will move own desc to the desc_freed. So, this driver should use
list_for_each_entry_safe() instead of list_for_each_entry().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When a DMA client driver decides that it is not providing callback for
completion of a transfer (and/or does not set the DMA_PREP_INTERRUPT) but
it will poll the status of the transfer (in case of short memcpy for
example) we will not get interrupt for the completion of the transfer and
will not mark the transaction as done.
Check the channel enable bit in the CCR when the status is queried and if
the channel is no longer active, we call the omap_dma_callback() to handle
the transfer completion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The use of tasklet to actually start the DMA transfer slightly decreases the
DMA throughput since it adds small scheduling delay when the transfer is
started. In normal use, even with high I/O load the tasklet would start
one transaction at a time, however running the DMAtest for memcpy on all
available channels will cause the tasklet to start about 15 transfers.
The performance numbers on OMAP4 PandaBoard-es (test_buf_size = 6553):
With the tasklet:
dmatest: dma0chan30-copy: summary 5000 tests, 0 failures 186 iops 593 KB/s (0)
dmatest: dma0chan8-copy0: summary 5000 tests, 0 failures 184 iops 584 KB/s (0)
dmatest: dma0chan13-copy: summary 5000 tests, 0 failures 184 iops 585 KB/s (0)
dmatest: dma0chan12-copy: summary 5000 tests, 0 failures 184 iops 585 KB/s (0)
dmatest: dma0chan7-copy0: summary 5000 tests, 0 failures 183 iops 581 KB/s (0)
With this patch (no tasklet):
dmatest: dma0chan4-copy0: summary 5000 tests, 0 failures 199 iops 644 KB/s (0)
dmatest: dma0chan5-copy0: summary 5000 tests, 0 failures 199 iops 645 KB/s (0)
dmatest: dma0chan6-copy0: summary 5000 tests, 0 failures 199 iops 637 KB/s (0)
dmatest: dma0chan24-copy: summary 5000 tests, 0 failures 199 iops 638 KB/s (0)
dmatest: dma0chan16-copy: summary 5000 tests, 0 failures 199 iops 638 KB/s (0)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The for_each_sg() macro's last parameter is inteded to be used as counter.
We can use 'i' instead of 'j' within the loop for indexes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During mem copy both src and dst position moves at the same pace. Check the
dst position for progress reporting.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In eDMA the events are directly mapped to a DMA channel (for example DMA
event 14 can only be handled by DMA channel 14). If the memcpy is enabled
on the eDMA, there is a possibility that the crossbar driver would assign
DMA event number already allocated in eDMA for memcpy. Furthermore the
eDMA can be shared with DSP in which case the crossbar driver should also
avoid mapping xbar events to DSP used event numbers (or channels).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The use of idr was nice, but it was a bit heavy and we did not need the
features it provides. Using simple bitmap to track allocated DMA channels
is adequate here and it will be easier to add support for reserving
channels later on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Allow the crossbar driver to be used with the eDMA node with non legacy
binding.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As we are now passing the filter data as pointers to the drivers,
we can take the final step and also pass the filter function the
same way. I'm keeping this change separate, as there it's less
obvious that this is a net win.
Upsides of this are:
- The ASoC drivers are completely independent from the DMA engine
implementation, which simplifies the Kconfig logic and in theory
allows the same sound drivers to be built in a kernel that supports
different kinds of dmaengine drivers.
- Consistency with other subsystems and drivers
On the other hand, we have a few downsides:
- The s3c24xx-dma driver now needs to be built-in for the ac97 platform
device to be instantiated on s3c2440.
- samsung_dmaengine_pcm_config cannot be marked 'const' any more
because the filter function pointer needs to be set at runtime.
This is safe as long we don't have multiple different DMA engines
in thet same system at runtime, but is nonetheless ugly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dca_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_addr_t may be defined as 32 or 64 bit depending on configuration,
so it cannot be printed using the normal format strings, as
gcc correctly warns:
drivers/dma/at_hdmac.c: In function 'atc_prep_dma_interleaved':
drivers/dma/at_hdmac.c:731:28: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the format strings to use the special "%pad" format
string that prints a dma_addr_t, and changes the arguments so we
pass the address by reference as required.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_addr_t may be defined as 32 or 64 bit depending on configuration,
so it cannot be printed using the normal format strings, as
gcc correctly warns:
drivers/dma/at_xdmac.c: In function 'at_xdmac_interleaved_queue_desc':
drivers/dma/at_xdmac.c:922:51: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the format strings to use the special "%pad" format
string that prints a dma_addr_t, and changes the arguments so we
pass the address by reference as required.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sdma_probe function will call sdma_event_remap, but sdma_event_remap
marked with the __init annotation which make the kbuild complains as the
following log:
WARNING: drivers/dma/built-in.o(.text+0x56fc): Section mismatch in reference
from the function sdma_probe() to the function .init.text:sdma_event_remap()
The function sdma_probe() references
the function __init sdma_event_remap().
This is often because sdma_probe lacks a __init
annotation or the annotation of sdma_event_remap is wrong.
Remove the __init annotation on sdma_event_remap to kill this build warning
Signed-off-by: Jason Liu <r64343@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove pre-3.0 channel status reads. 3.0 and later chansts register
is 64bit and can be read 64bit. This was clarified with the hardware
architects and since the driver now only support 3.0+ we don't need the
legacy support
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current code uses bits 0-2 instead of 4-6 as the comment says.
Fixes: 633e42b8c5 ('dmaengine: edma: Get qDMA channel information from HW also')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During the edma rework, a build error was introduced for the
case that CONFIG_OF is disabled:
drivers/built-in.o: In function `edma_tc_set_pm_state':
:(.text+0x43bf0): undefined reference to `of_find_device_by_node'
As the edma_tc_set_pm_state() function does nothing in case
we are running without OF, this adds an IS_ENABLED() check
that turns the function into an empty stub then and avoids the
link error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca304fa9bb ("ARM/dmaengine: edma: Public API to use private struct pointer")
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the STM32 DMA controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the call to pm_runtime_get_sync() failed, Runtime PM was left
enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If CONFIG_PREEMPT=y:
Unable to handle kernel NULL pointer dereference at virtual address 00000014
pgd = c0003000
[00000014] *pgd=80000040004003, *pmd=00000000
Internal error: Oops: 206 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 17 Comm: kworker/0:1 Tainted: G W 4.3.0-rc3-koelsch-022
71-g705498fc5e6a5da8-dirty #1789
Hardware name: Generic R8A7791 (Flattened Device Tree)
Workqueue: pm pm_runtime_work
task: ef578e40 ti: ef57a000 task.ti: ef57a000
PC is at usb_dmac_chan_halt+0xc/0xc0
LR is at usb_dmac_runtime_suspend+0x28/0x38
pc : [<c023c880>] lr : [<c023c95c>] psr: 80000113
sp : ef57bdf8 ip : 00000008 fp : 00000003
r10: 00000008 r9 : c06ab928 r8 : ef49e810
r7 : 00000000 r6 : 000000ac r5 : ef770010 r4 : 00000000
r3 : 00000000 r2 : 8ffc2b84 r1 : 00000000 r0 : ef770010
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 30c5307d Table: 40003000 DAC: fffffffd
Process kworker/0:1 (pid: 17, stack limit = 0xef57a210)
Stack: (0xef57bdf8 to 0xef57c000)
[...
[<c023c880>] (usb_dmac_chan_halt) from [<c023c95c>] (usb_dmac_runtime_suspend+0x28/0x38)
[<c023c95c>] (usb_dmac_runtime_suspend) from [<c027b25c>] (pm_genpd_runtime_suspend+0x74/0x23c)
This happens because usb_dmac_probe() calls pm_runtime_put() before
usb_dmac_chan_probe(), leading to the device being suspended before the
DMA channels are initialized, causing a NULL pointer dereference.
Move the call to pm_runtime_put() to the end of usb_dmac_probe() to fix
this.
Add a check to usb_dmac_runtime_suspend() to prevent the crash from
happening in the error path.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As this driver provides a mechanism to reuse transfers, declare it in
its probe function.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the current state, the capability of transfer reuse can neither be
set by a slave dmaengine driver, nor used by a client driver, because
the capability is not available to dma_get_slave_caps().
Fix this by adding a way to declare the capability.
Fixes: 272420214d ("dmaengine: Add DMA_CTRL_REUSE")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch attempts to enhance the case of a transfer submitted multiple
times, and where the cost of creating the descriptors chain is not
negligible.
This happens with big video buffers (several megabytes, ie. several
thousands of linked descriptors in one scatter-gather list). In these
cases, a video driver would want to do :
- tx = dmaengine_prep_slave_sg()
- dma_engine_submit(tx);
- dma_async_issue_pending()
- wait for video completion
- read video data (or not, skipping a frame is also possible)
- dma_engine_submit(tx)
=> here, the descriptors chain recalculation will take time
=> the dma coherent allocation over and over might create holes in
the dma pool, which is counter-productive.
- dma_async_issue_pending()
- etc ...
In order to cope with this case, virt-dma is modified to prevent freeing
the descriptors upon completion if DMA_CTRL_REUSE flag is set in the
transfer.
This patch is a respin of the former DMA_CTRL_ACK approach, which was
reverted due to a regression in audio drivers.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Implement the new device_synchronize() callback to allow proper
synchronization when stopping a channel. Since the driver already makes
sure that no new complete callbacks are scheduled after the
device_terminate_all() callback has been called, all left to do in the
device_synchronize() callback is to wait for all currently running complete
callbacks to finish.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add a synchronize helper function for the virt-dma library. The function
makes sure that any scheduled descriptor complete callbacks have finished
running before the function returns.
This needs to be called by drivers using virt-dma in their
device_synchronize() callback. Depending on the driver additional
operations might be necessary in addition to calling vchan_synchronize() to
ensure proper synchronization.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMAengine API has a long standing race condition that is inherent to
the API itself. Calling dmaengine_terminate_all() is supposed to stop and
abort any pending or active transfers that have previously been submitted.
Unfortunately it is possible that this operation races against a currently
running (or with some drivers also scheduled) completion callback.
Since the API allows dmaengine_terminate_all() to be called from atomic
context as well as from within a completion callback it is not possible to
synchronize to the execution of the completion callback from within
dmaengine_terminate_all() itself.
This means that a user of the DMAengine API does not know when it is safe
to free resources used in the completion callback, which can result in a
use-after-free race condition.
This patch addresses the issue by introducing an explicit synchronization
primitive to the DMAengine API called dmaengine_synchronize().
The existing dmaengine_terminate_all() is deprecated in favor of
dmaengine_terminate_sync() and dmaengine_terminate_async(). The former
aborts all pending and active transfers and synchronizes to the current
context, meaning it will wait until all running completion callbacks have
finished. This means it is only possible to call this function from
non-atomic context. The later function does not synchronize, but can still
be used in atomic context or from within a complete callback. It has to be
followed up by dmaengine_synchronize() before a client can free the
resources used in a completion callback.
In addition to this the semantics of the device_terminate_all() callback
are slightly relaxed by this patch. It is now OK for a driver to only
schedule the termination of the active transfer, but does not necessarily
have to wait until the DMA controller has completely stopped. The driver
must ensure though that the controller has stopped and no longer accesses
any memory when the device_synchronize() callback returns.
This was in part done since most drivers do not pay attention to this
anyway at the moment and to emphasize that this needs to be done when the
device_synchronize() callback is implemented. But it also helps with
implementing support for devices where stopping the controller can require
operations that may sleep.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we have a very typical update which is mostly fixes and updates to
drivers and no new drivers.
- Biggest change is coming from Peter for edma cleanup which even caused
some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tIzO
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have a very typical update which is mostly fixes and
updates to drivers and no new drivers.
- the biggest change is coming from Peter for edma cleanup which even
caused some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac"
* tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (77 commits)
dmaengine: edma: Add dummy driver skeleton for edma3-tptc
Revert "ARM: DTS: am33xx: Use the new DT bindings for the eDMA3"
Revert "ARM: DTS: am437x: Use the new DT bindings for the eDMA3"
dmaengine: dw: some Intel devices has no memcpy support
dmaengine: dw: platform: provide platform data for Intel
dmaengine: dw: don't override platform data with autocfg
dmaengine: hdmac: Add scatter-gathered memset support
dmaengine: hdmac: factorise memset descriptor allocation
dmaengine: virt-dma: Fix kernel-doc annotations
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: New device tree binding
dmaengine: Kconfig: edma: Select TI_DMA_CROSSBAR in case of ARCH_OMAP
dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx
dmaengine: edma: Merge the of parsing functions
dmaengine: edma: Do not allocate memory for edma_rsv_info in case of DT boot
dmaengine: edma: Refactor the dma device and channel struct initialization
dmaengine: edma: Get qDMA channel information from HW also
dmaengine: edma: Merge map_dmach_to_queue into assign_channel_eventq
dmaengine: edma: Correct PaRAM access function names (_parm_ to _param_)
...
Here is the big char/misc driver update for 4.4-rc1. Lots of different
driver and subsystem updates, hwtracing being the largest with the
addition of some new platforms that are now supported. Full details in
the shortlog.
All of these have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6d/oACgkQMUfUDdst+yl93ACcCf91y+ufwU3cmcnq5LpwHPfx
VbkAn08Cn6Wu6IcihoEpR4hqGgIOtjqW
=1a3d
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.4-rc1. Lots of
different driver and subsystem updates, hwtracing being the largest
with the addition of some new platforms that are now supported. Full
details in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (181 commits)
fpga: socfpga: Fix check of return value of devm_request_irq
lkdtm: fix ACCESS_USERSPACE test
mcb: Destroy IDA on module unload
mcb: Do not return zero on error path in mcb_pci_probe()
mei: bus: set the device name before running fixup
mei: bus: use correct lock ordering
mei: Fix debugfs filename in error output
char: ipmi: ipmi_ssif: Replace timeval with timespec64
fpga: zynq-fpga: Fix issue with drvdata being overwritten.
fpga manager: remove unnecessary null pointer checks
fpga manager: ensure lifetime with of_fpga_mgr_get
fpga: zynq-fpga: Change fw format to handle bin instead of bit.
fpga: zynq-fpga: Fix unbalanced clock handling
misc: sram: partition base address belongs to __iomem space
coresight: etm3x: adding documentation for sysFS's cpu interface
vme: 8-bit status/id takes 256 values, not 255
fpga manager: Adding FPGA Manager support for Xilinx Zynq 7000
ARM: zynq: dt: Updated devicetree for Zynq 7000 platform.
ARM: dt: fpga: Added binding docs for Xilinx Zynq FPGA manager.
ver_linux: proc/modules, limit text processing to 'sed'
...
Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6f64ACgkQMUfUDdst+ykf8gCfYPjtHy5hD/TsharaeXROnVgi
W8cAn16xk1Nmnde220MNNpO6zDu65G/1
=kslf
-----END PGP SIGNATURE-----
Merge tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (148 commits)
tty: Use unbound workqueue for all input workers
tty: Abstract tty buffer work
tty: Prevent tty teardown during tty_write_message()
tty: core: Use correct spinlock flavor in tiocspgrp()
tty: Combine SIGTTOU/SIGTTIN handling
serial: amba-pl011: fix incorrect integer size in pl011_fifo_to_tty()
ttyFDC: Fix build problems due to use of module_{init,exit}
tty: remove unneeded return statement
serial: 8250_mid: add support for DMA engine handling from UART MMIO
dmaengine: hsu: remove platform data
dmaengine: hsu: introduce stubs for the exported functions
dmaengine: hsu: make the UART driver in control of selecting this driver
serial: fix mctrl helper functions
serial: 8250_pci: Intel MID UART support to its own driver
serial: fsl_lpuart: add earlycon support
tty: disable unbind for old 74xx based serial/mpsc console port
serial: pl011: Spelling s/clocks-names/clock-names/
n_tty: Remove reader wakeups for TTY_BREAK/TTY_PARITY chars
tty: synclink, fix indentation
serial: at91, fix rs485 properties
...
The eDMA3 TPTC does not need any software configuration, but it is a
separate IP block in the SoC. In order the omap hwmod core to be able to
handle the TPTC resources correctly in regards of PM we need to have a
driver loaded for it.
This patch will add a dummy driver skeleton without probe or remove
callbacks provided.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Provide a flag to choose if the device does support memory-to-memory transfers.
At least this is not true for iDMA32 controller that might be supported in the
future. Besides that Intel BayTrail and Braswell users should not try this
feature due to HW specific behaviour.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Provide platform data explicitly for Intel SoCs where dw_dmac is enumerated by
ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Let probe driver decide either it wants to auto configure the driver or have
explicitly defined properties.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Just like memset support, the HDMAC might be used to do a memset over a
discontiguous memory area.
In such a case, we'll just build up a chain of memset descriptors over the
contiguous chunks of memory to set, in order to allow such a support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The memset and scatter gathered memset are going to use some common logic
to create their descriptors.
Move that logic into a function of its own so that we can share it with the
future memset_sg callback.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In kernel-doc annotations parameters need to start with a @ for them to be
properly recognized. Add those where missing for virt-dma.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With the old binding and driver architecture we had many issues:
No way to assign eDMA channels to event queues, thus not able to tune the
system by moving specific DMA channels to low/high priority servicing. We
moved the cyclic channels to high priority within the code, but that was
just a workaround to this issue.
Memcopy was fundamentally broken: even if the driver scanned the DT/devices
in the booted system for direct DMA users (which is not effective when the
events are going through a crossbar) and created a map of 'used' channels,
this information was not really usable. Since via dmaengien API the eDMA
driver will be called with _some_ channel number, we would try to request
this channel when any channel is requested for memcpy. By luck we got
channel which is not used by any device most of the time so things worked,
but if a device would have been using the given channel, but not requested
it, the memcpy channel would have been waiting for HW event.
The old code had the am33xx/am43xx DMA event router handling embedded. This
should have been done in a separate driver since it is not part of the
actual eDMA IP.
There were no way to 'lock' PaRAM slots to be used by the DSP for example
when booting with DT.
In DT boot the edma node used more than one hwmod which is not a good
practice and the kernel prints warning because of this.
With the new bindings and the changes in the driver we can:
- No regression with Legacy binding and non DT boot
- DMA channels can be assigned to any TC (to set priority)
- PaRAM slots can be reserved for other cores to use
- Dynamic power management for CC and TCs, if only TC0 is used all other TC
can be powered down for example
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the crossbar is needed for eDMA when it is used on OMAP like
platforms (am335x/am437x and later DRA7xx), select the crossbar to be built
if ARCH_OMAP is set.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMA event crossbar on AM33xx/AM43xx is different from the one found in
DRA7x family.
Instead of a single event crossbar it has 64 identical mux attached to each
eDMA event line. When the 0 event mux is selected, the default mapped event
is going to be routed to the corresponding eDMA event line. If different
mux is selected, then the selected event is going to be routed to the given
eDMA event.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of nesting functions just merge them since the resulting function
is still small and readable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The channel/slot reservation is not supported when booted with DT so there
is not need to allocate memory.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move all code under one function to do the dma device and eDMA channel
related setup so they are not scattered around the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Query the number of qDMA channels from CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
edma_assign_channel_eventq() is a wrapper around edma_map_dmach_to_queue()
We can merge the content of the later so we will have only one function
to be used for mapping channels to given eventq
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
These inline functions are designed to modify parts of the PaRAM in eDMA.
Change the names accordingly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of passing a pointer to struct edma_cc and the channel number,
pass only the pointer to the edma_chan structure for the given channel.
This struct contains all the information needed by the functions and the
use of this makes it obvious that most of the sanity checks can be removed
from the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the transfer is shorted then 64K we can complete it with one ACNT burst
by configuring ACNT to the length of the copy, this require one paRAM slot.
Otherwise we use two paRAM slots for the copy:
slot1: will copy (length / 32767) number of 32767 byte long blocks
slot2: will be configured to copy the remaining data.
According to tests this patch increases the throughput of memcpy from
~3MB/s to 15MB/s
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Despite the claim by the original commit adding the memcpy
support, eDMA does not have constraint on the alignment of src, dst
or length in increment mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are no platforms where it's not possible to calculate
the number of channels based on IO space length, and since
that is the only purpose for struct hsu_dma_platform_data,
removing it.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HSU (High Speed UART) DMA engine, like the name suggests, is
an integrated DMA engine for UART and UART alone. Therefore,
making the UART drivers responsible of selecting it and
removing the user selectable option for it. The UARTs with
this DMA engine can always select HSU_DMA when
SERIAL_8250_DMA option is enabled.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA engine supports memory copy, RAID5 XOR, RAID6 PQ, and other
computations. But the bandwidth of the entire DMA engine is shared
among all channels. This patch re-configures operations availability
such that one can achieve maximum performance for XOR and PQ
computation by removing the memory offload operations.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the eDMA3 has support for channel paRAM slot mapping we can utilize it
to allocate slots on demand and save precious slots for real transfers.
On am335x the eDMA has 64 channels which means we can unlock 64 paRAM
slots out from the available 256.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The names chosen for the bitfields were quite confusing and given no real
information on what they are used for...
edma_inuse -> slot_inuse: tracks the slot usage/availability
edma_unused -> channel_unused: tracks the channel usage/availability
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of directly reading it from CCCFG register take the information out
once when we set up the configuration from the HW.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
No need to run through the bits in QEMR and CCERR events since they will
not trigger any action, so just clearing the errors there is fine.
In case of the missed event the loop can be optimized so we spend less time
to handle the event.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the ccerr interrupt handler the code checks for pending errors in the
error status registers in two different places.
Move the check out to a helper function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With the merger of the arch/arm/common/edma.c code into the dmaengine
driver, there is no longer need to have per channel callback/data storage
for interrupt events.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove or rewrite the comments for the internal functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Warning message in case of linking between paRAM slots in different eDMA
controllers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
edma_write_slot() is for writing an entire paRAM slot.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have access to dev, so it is better to use the dev_dbg for debug prints.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Be consistent and do not mix the use of dev, &pdev->dev, etc in the
functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When allocating a memory for number of items it is better (looks better)
to use devm_kcalloc.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of using defines to specify the size of different arrays and
bitmaps, allocate the memory for them based on the information we get from
the HW itself.
Since these defines are set based on the worst case, there are devices
where they are not valid.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move the code out from arch/arm/common and merge it inside of the dmaengine
driver.
This change is done with as minimal (if eny) functional change to the code
as possible to avoid introducing regression.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the driver stack no longer depends on lookup with id number in a
global array of pointers, the limitation for the number of eDMAs are no
longer needed. We can handle as many eDMAs in legacy and DT boot as we have
memory for them to allocate the needed structures.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of relying on indexes pointing to edma private date in the global
pointer array, pass the private data pointer via the public API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the of_dma_controller is registered in the non dmaengine driver we could
have race condition:
the of_dma_controller has been registered, but the dmaengine driver is not
yet probed. Drivers requesting DMA channels during this window will fail
since we do not yet have dmaengine drivers registered.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code path in edma_execute() and edma_callback() can be simplified
and make it more optimal.
There is not need to call in to edma_execute() when the transfer
has been finished for example.
Also the handling of missed/first or next batch of paRAMs can
be done in a more optimal way.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to print that the driver has been initialized
or removed, so remove such messages.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since commit d078cd1b41 ("dmaengine: imx-sdma: Add imx6sx platform
support") we get this message on every boot on mx6q:
imx-sdma 20ec000.sdma: no event needs to be remapped
, which is not very helpful.
Move the message to debug level instead.
Cc: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is needed due to the duplicated iommu stuff to help with the merge
and to prevent future issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The L3 throughput can be higher than expected when packed access
is not enabled. The ratio depends on the number of bytes in a
transaction and the EMIF interface width.
The throughput was measured for the following settings/cases:
* Case 1: Burst size of 64 bytes, packed access disabled
* Case 2: Burst size of 64 bytes, packed access enabled
* Case 3: Burst disabled, packed access disabled
Throughput measurements were done during McASP-based audio
playback on the Jacinto6 EVM using the omapconf tool [1]:
$ omapconf trace bw -m sdma_rd
---------------------------------------------------------
Throughput (MB/s)
Audio parameters Case 1 Case 2 Case 3
---------------------------------------------------------
44.1kHz, 16-bits, stereo 1.41 0.18 1.41
44.1kHz, 32-bits, stereo 1.41 0.35 1.41
44.1kHz, 16-bits, 4-chan 2.82 0.35 2.82
44.1kHz, 16-bits, 6-chan 4.23 0.53 4.23
44.1kHz, 16-bits, 8-chan 5.64 0.71 5.64
---------------------------------------------------------
From above measurements, case 2 is the only one that delivers
the expected throughput for the given audio parameters. For
that reason, the packed accesses are now enabled.
It's worth to mention that packed accesses cannot be enabled
for all addressing modes. In cyclic transfers, it can be
enabled in the source for MEM_TO_DEV and in dest for DEV_TO_MEM,
as they use post-increment mode which supports packed accesses.
Peter Ujfalusi:
From the TRM regarding to this:
"NOTE: Except in the constant addressing mode, the source or
destination must be specified as packed for burst transactions
to occur."
So w/o the packed setting the burst on the MEM side was not
enabled, this explains the numbers.
[1] https://github.com/omapconf/omapconf
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The MIC X100 DMA engine has a special status descriptor which writes
an 8 byte value to a destination location. This is used to signal
completion of all DMA descriptors prior to the status descriptor.
This patch add a new DMA engine API which enables updating a
destination address with an 8 byte immediate data value.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Lawrynowicz, Jacek <jacek.lawrynowicz@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Siva Yerramreddy <yshivakrishna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This contains fixes spread throughout the drivers
Also fixes one more instance of privatecnt in dmaengine
bunch of pxa_dma fixes for reuse of descriptor issue, residue and
no-requestor
odd fixes in xgene, idma, sun4i and zxdma
at_xdmac fixes for cleaning descriptor and block addr mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wcjo
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.3-rc4' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"This contains fixes spread throughout the drivers, and also fixes one
more instance of privatecnt in dmaengine.
Driver fixes summary:
- bunch of pxa_dma fixes for reuse of descriptor issue, residue and
no-requestor
- odd fixes in xgene, idma, sun4i and zxdma
- at_xdmac fixes for cleaning descriptor and block addr mode"
* tag 'dmaengine-fix-4.3-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: pxa_dma: fix residue corner case
dmaengine: pxa_dma: fix the no-requestor case
dmaengine: zxdma: Fix off-by-one for testing valid pchan request
dmaengine: at_xdmac: clean used descriptor
dmaengine: at_xdmac: change block increment addressing mode
dmaengine: dw: properly read DWC_PARAMS register
dmaengine: xgene-dma: Fix overwritting DMA tx ring
dmaengine: fix balance of privatecnt
dmaengine: sun4i: fix unsafe list iteration
dmaengine: idma64: improve residue estimation
dmaengine: xgene-dma: fix handling xgene_dma_get_ring_size result
dmaengine: pxa_dma: fix initial list move
A very tiny temporal window exists in the residue calculation where :
- upon entering residue calculation, the transfer is ongoing
- when reading the current transfer pointer, it just changed to
the "finisher/linker" descriptor
In this case, the residue returned is the whole transfer length instead
of 0. Fix it.
This appears almost in one extreme case, where the driver is used
by older clients which inquire for residue in interrupt context, such
as the smsc91x ethernet driver, in a tight loop :
interrupt_handler()
dmaengine_submit()
do {
dmaengine_tx_status()
} while (residue > 0 || status != DMA_ERROR)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A very small number of devices don't use the flow control offered by
requestor lines. In these specific cases, the pxa dma driver should be
aware of that and not try to use a requestor line.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The valid pchan range is 0 ~ d->dma_requests - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In interleaved mode, when numf > 1, we have only one descriptor for the
transfer but this descriptor has to be added to the descs_list. If not,
when doing remove_xfer, the descriptor won't be put back in the
free_descs_list.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When putting back a descriptor to the free descs list, some fields are
not set to 0, it can cause bugs if someone uses it without having this
in mind.
Descriptor are not put back one by one so it is easier to clean
descriptors when we request them.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org #4.2
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The addressing mode we were using was not only incrementing the address at
each microblock, but also at each data boundary, which was severely slowing
the transfer, without any benefit since we were not using the data stride.
Switch to the micro block increment only in order to get back to an
acceptable performance level.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 6007ccb577 ("dmaengine: xdmac: Add interleaved transfer support")
Cc: stable@vger.kernel.org #4.2
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the call to memset in this driver
[linux-4.2-next-20150911/drivers/dma/zx296702_dma.c:444]: (warning)
memset() called to fill 0 bytes of 'ds'.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of hardconding a platform data for dw_dmac let's use it's own
autoconfiguration feature. Thus, remove hardcoded values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We replace __fls() by __ffs() since we have to find a *minimum* data width that
satisfies both source and destination.
While here, rename dwc_fast_fls() to dwc_fast_ffs() which it really is.
Fixes: 4c2d56c574 (dw_dmac: introduce dwc_fast_fls())
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case we have less than maximum allowed channels (8) and autoconfiguration is
enabled the DWC_PARAMS read is wrong because it uses different arithmetic to
what is needed for channel priority setup.
Re-do the caclulations properly. This now works on AVR32 board well.
Fixes: fed2574b3c (dw_dmac: introduce software emulation of LLP transfers)
Cc: yitian.bu@tangramtek.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes an over flow issue with the TX ring descriptor. Each
descriptor is 32B in size and an operation requires 2 of these
descriptors.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_release_channel() decrements privatecnt counter and almost all dma_get*
function increments it with the exception of dma_get_slave_channel().
In most cases this does not cause issue since normally the channel is not
requested and released, but if a driver requests DMA channel via
dma_get_slave_channel() and releases the channel the privatecnt will be
unbalanced and this will prevent for example getting channel for memcpy.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Get pointer to the struct acpi_device by using ACPI_COMPANION() macro. This
is more efficient than using ACPI_HANDLE() and acpi_bus_get_device().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, sun4i_dma_free_contract iterates over lists and frees memory
as it goes through them, causing reads to recently freed memory to
be performed. Fix this by using the safe version of the iterator, so
freed memory is not referenced at all.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
in edma_callback, driver was doing redundant check for desc, so remove that
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are already helper functions to do 64-bit I/O on 32-bit machines, thus we
don't need to reinvent the wheel. In our case we can't use readq() / writeq()
even on 64-bit kernel since there is a hardware limitation (OCP bus is a 32-bit
bus).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Accordingly to the documentation the CH_DRAIN bit enforses single bursts when
channel is going to be suspended. This, in case when channel will be resumed,
makes data to flow in non-optimal mode until DMA returns to full burst mode.
The fix differentiates pause / resume cycle from pause / terminate and sets
CH_DRAIN bit accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes a comment where DesignWare is wrongly mentioned. There is no
functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We use a pattern
x = min_t(u32, <LOG2_CONSTANT>, __ffs(expr));
There is no need to use min_t() since we can replace it by
x = __ffs(expr | <2^LOG2_CONST>);
and moreover guarantee that argument of __ffs() will be not zero.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We replace __fls() by __ffs() since we have to find a *minimum* data width that
satisfies both source and destination.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The residue calculation may provide a wrong estimation when the transfer is
started. There are possible scenarios we have to separate:
1) the transfer is not started yet; residue is equal to the total
length;
2) the transfer is just started (first chunk is ongoing); residue is
equal to the total length without already transfered bytes;
3) the transfer is ongoing and we already sent few chunks of data;
residue is equal to the total length without fully transfered chunks
and already sent bytes.
Mistakenly the calculation in cases 2) and 3) was done in the similar way and
the result is equal to -bytes that have been transfered, i.e. quite big since
size_t type can't keep negative values.
Rewrite the calculation algorithm to be one pass and have a correct result.
Besides above in case user asks for a status of the active DMA descriptor
without pausing an ongoing transfer the residue will be estimated based on the
register value, though it's still racy. Since the transfer is active the value
is continuously being changed. Here we have to read two registers at a time. To
minimize an error make those reads close to each other.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the commit to have an allocated list of virtual descriptors was
reverted, the pxa_dma driver is broken, as it assumes the descriptor is
placed on the allocated list upon allocation.
Fix the issue in pxa_dma by making an allocated virtual descriptor a
singleton.
Fixes: 8c8fe97b2b ("Revert "dmaengine: virt-dma: don't always free descriptor upon completion"")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current implementation hard codes the two supported channels so that
"tx" is always 0 and "rx" is always 1. This is because there has been no
suitable way in ACPI to name resources.
With _DSD device properties we can finally do this:
Device (SPI1) {
Name (_CRS, ResourceTemplate () {
...
FixedDMA (0x0000, 0x0000, Width32bit)
FixedDMA (0x0001, 0x0001, Width32bit)
})
Name (_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"dma-names", Package () {"tx", "rx"}}
},
})
}
The names "tx" and "rx" now provide index of the FixedDMA resource in
question.
Modify acpi_dma_request_slave_chan_by_name() so that it looks for
"dma-names" property first and only then fall back using hardcoded indices.
The DT "dma-names" binding that we reuse for ACPI is documented in
Documentation/devicetree/bindings/dma/dma.txt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
the symbol CONFIG_IDMA64 should rather be CONFIG_INTEL_IDMA64 to conform to
rest of the intel dmaengine drivers. This was found after sorting the
entries and trying to place this odd one
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adding AER handlers in order to handle any PCIe errors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi