Fix the following warning:
CC arch/arm/mach-mx5/board-mx53_loco.o
arch/arm/mach-mx5/board-mx53_loco.c:203: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MFD changes in 4ec1b54c ('mfd: mfd_cell is now implicitly available to
mc13xxx drivers') changed the mc13xxx_platform_data struct layout.
At the time all users were changed, but this driver was introduced in
another tree at the same time. This updates the mc13xxx_platform_data
user, fixing a build error.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Note that this relies on stuff currently in mfd's next tree, but this
is also a newer driver. I'm not sure which tree it should go through,
as it's a problem that shows up in next.
From: Andres Salomon <dilinger@queued.net>
MFD changes in c738892f cause the mc13xxx_platform_data struct
to change. This changes one more (new) user of it, fixing a build
error.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Implement code for MX51 that allows the SoC to enter WFI when
arch_idle is called.
This patch is also necessary for correctly suspending the system.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For MX51 SRPG, we need to turn on the GPC clock in order to set the
SRPG registers.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For MX50, the HW_ADADIG_DIGPROG register in the ANATOP module will
have the correct silicon revision:
Major Minor Description
0x50 0x0 TO1.0
0x50 0x1 TO1.1
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As there is a mx53_smd board in the kernel, using SMD_FEC_PHY_RST as the pin name can be misleading when used
on a MX53_EVK board.
Change the pin name to reflect the board name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code inside mx53_evk_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value right after. This is not needed.
By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code inside babbage_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value to the same level right after. This is not needed.
By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Having the silicon revision to appear on the boot log is a useful information.
MX31 and MX35 already show the silicon revision on boot.
Add support for displaying such information for MX51 as well.
Tested on a MX51EVK, where it shows:
CPU identified as i.MX51, silicon rev 3.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The boards are currently using otg_ulpi_create and mxc_ulpi_access_ops,
both are only present if CONFIG_USB_ULPI is set. To remove the need of
ifdefs in the board code introduce a imx_otg_ulpi_create functions
which expands to a static inline function if compiled without ulpi.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On mx53_evk board only RX/TX pins are used on UART3.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On mx53_smd board only RX/TX pins are used on UART2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- wrong MUX was set before for IRQ
- get_pendown_state is no more needed
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch declares regulators for the efikamx. Use it also to power off the
efikamx.
Unfortunately, on the efikamx to2 boards, this doesn't work but they allow to
power off by setting GPIO 4 13 to high level instead of powering off through
the mc13892.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that usb has been fixed, we can enable usb h1 on efikamx
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things
so it makes sense to create a common file for both devices and a specific
file for each. No functionnal change except dropping uart 1 & 2.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mxc_board_init is too generic to be useful. Additionally change some
mxc_timer to ${machine}_timer, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mxc-ehci driver calls SoC specific phy initialization right after
calling board specific initialization. To offer greater flexibility for
boards to setup the phy and to get rid of some unnecessary flags in
platform data this patch lets the boards call the SoC specific phy
initialization and remove it from the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we have a mxc_initialize_usb_hw which is called on every
i.MX SoC. This function dispatches the different SoC types, which
is quite ugly. This patch moves the SoC specific USB initialization
to their correspondive mach directories.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix UART1 IOMUX settings and configure UART1 to work with only RX/TX pins.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix UART1 IOMUX settings and configure UART1 to work with only RX/TX pins.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On mx53_loco only UART1 is used and its signals go to connector J16.
Remove UART2 and UART3 as they are not used on this board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 816ad74 (ARM: i.MX53: Add full iomux support for mx53) renamed some of the pad names.
Make the changes accordingly so that mx53_loco and mx53_cmd can build without errors.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fabio Estevam