The "iavcc" and "iadev" cases are obvious.
The intr_status and frmr_intr cases are reading a register to clear
the chip status. This driver is pretty old and creaky, and uses
volatile pointer dereferences to do register I/O when it should be
using readl() and friends. However that it outside of the scope of
these changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following warnings:
net/9p/client.c:1305:18: warning: variable ‘total’ set but not used [-Wunused-but-set-variable]
net/9p/client.c:1370:18: warning: variable ‘total’ set but not used [-Wunused-but-set-variable]
net/9p/client.c:1769:18: warning: variable ‘total’ set but not used [-Wunused-but-set-variable]
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ndo_fix_features callback is postponing features change when
bp->recovery_state != BNX2X_RECOVERY_DONE, netdev_update_features()
has to be called again when this condition changes. Previously,
ethtool_ops->set_flags callback returned -EBUSY in that case
(it's not possible in the new model).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
v5: - don't delay set_features, as it's rtnl_locked - same as recovery process
v4: - complete bp->rx_csum -> NETIF_F_RXCSUM conversion
- add check for failed ndo_set_features in ndo_open callback
v3: - include NETIF_F_LRO in hw_features
- don't call netdev_update_features() if bnx2x_nic_load() failed
v2: - comment in ndo_fix_features callback
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: looks like bnad->conf_mutex is duplicating rtnl_lock.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caveats:
- driver modifies vlan_features on HW VLAN TX changes
- broken RX checksum will be reenabled on features change
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now there are 2 paths for rx vlan frames. When rx-vlan-hw-accel is
enabled, skb is untagged by NIC, vlan_tci is set and the skb gets into
vlan code in __netif_receive_skb - vlan_hwaccel_do_receive.
For non-rx-vlan-hw-accel however, tagged skb goes thru whole
__netif_receive_skb, it's untagged in ptype_base hander and reinjected
This incosistency is fixed by this patch. Vlan untagging happens early in
__netif_receive_skb so the rest of code (ptype_all handlers, rx_handlers)
see the skb like it was untagged by hw.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v1->v2:
remove "inline" from vlan_core.c functions
Signed-off-by: David S. Miller <davem@davemloft.net>
When blinking for a duration set by the user, the value specified is in
seconds but it is used as the number of jiffies in the timeout after which
the Physical ID indicator is deactivated. Fix by converting the timeout
to seconds.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vxge_hw_vpath_close, __vxge_hw_vp_terminate memsets the vpath which
clobbers the spin lock state, then the driver attempts to acquire the
spin lock. Resolve this by not zeroing the lock part of vpath struct,
clean-up vpath locking in init, close, and fix locking hole in fw_api
call.
Issue found by Bob Picco <bpicco@redhat.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware time stamp calculation can only be enabled by the privileged
function. Enable it always by default and simply use the ethtool
interface to set a flag to indicate whether or not the respective
function driver should indicate the timestamp along with the received
packet.
Also, make certain fields in vxge_hw_device_config bit-fields to reduce
the size of the struct.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of these are cases where we are trying to read back a register
after a write to ensure completion.
Simply pre-fixing the readl() or readq() with "(void)" is sufficient
because these are volatile operations and the compiler cannot eliminate
them just because no real assignment takes place.
The case of free_rxd_blk()'s assignments to "struct buffAdd *ba" is a
real spurious assignment as this variable is completely otherwise
unused.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jon Mason <jdmason@kudzu.us>
Most of these were legitimate, and once case was a real bug
(not propagating errors from ->xcvr_init() methods).
Signed-off-by: David S. Miller <davem@davemloft.net>
If CAIF Link Layer returns an error, we no longer try to re-build the
CAIF packet and resend it. Instead, we simply return any transmission
errors to the socket client.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup of new CAIF code.
* make local functions static
* remove code that is never used
* expand get_caif_conf() since wrapper is no longer needed
* make args to comparison functions const
* rename connect_req_to_link_param to keep exported names
consistent
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the RX network flow classification interface was originally
defined for reporting and controlling of flow hashing, AH and ESP were
not given distinct flow class codes (apparently because the Sun
Neptune hardware treats them very similarly).
For flow steering, they must be distinguished, so new and separate
flow class codes were added for AH and ESP. But for backward-
compatibility, flow hash operations should continue to support the
original class codes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code was cribbed from niu, so gfar_set_hash_opts() begins by
converting the ethtool flow class code into a class code for Sun
Neptune hardware, then does the same thing again for the hardware it's
really dealing with. It may also return -1 (-EPERM) for some
unhandled ethtool flow class codes.
Remove the useless code and definitions, and fix the error code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a stab at replacing old ethtool phys_id with set_phys_id
on the Qlogic 10Gb driver. Compile tested only.
Not sure if set_led_cfg will flash continuously, or needs
to be replaced by ETHTOOL_ID_ON/ETHTOOL_ID_OFF
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to add an ntuple data extensions to the rx network flow
classification specifiers. The idea is to allow ntuple to be displayed via
the network flow classification interface.
The first patch had some left over stuff from the original flow extension
flags I had added. That bit is removed in this patch.
The second had some left over comments that stated we ignored bits in the
masks when we actually match them.
This work is based on input from Ben Hutchings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to prevent a possible null pointer dereference if
NETIF_F_NTUPLE is defined but the set_rx_ntuple function pointer is not.
The main motivation behind this patch is to eventually replace the ntuple
interfaces entirely with the network flow classifier interfaces. This
allows the device drivers to maintain the ntuple check internally while
using the network flow classifier interface for setting up and displaying
rules.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the CAIF Payload message the Packet Type indication must be set to
UNCLASSIFIED in order to allow packet prioritization in the modem's
network stack. Otherwise TCP-Ack is not prioritized in the modems
transmit queue.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace relpy with reply.
replace premanent with permanent.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace tranmitted with transmitted.
replace tranmitting with transmitting.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, alb_bond_info uses rx_ntt,rlb_update_delay_counter and
rlb_update_retry_counter to decide when to call rlb_update_rx_clients().
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now bonding-alb uses delayed_work instead of timer_list.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to set save_load to 1 here,
as the tx_hashtbl is just kzalloced.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some old MAC chips without COE sometime the
Transmit Underflow error is issued.
The driver aborted all the transmission process
and initialized it from scratch.
This breaks the network activity as raised by Nachiketa
on a SPEAr board.
The patch is to fix this rare underflow event.
The driver will only clear the interrupt and the Tx
DMA will go out the Suspend state as soon as the
descriptor is fetched again.
The driver will continue to bump-up the DMA FIFO threshold
that, indeed, helped somebody to prevent this kind of error
in the past as well.
Reported-by: Nachiketa Prachanda <nprachanda@ncomputing.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reviews the open function and fixes some
errors when exit with an error state.
It also moves the request_irq after core is initialized
when interrupts are properly masked.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a compilation error when build the
dwmac_lib with the DEBUG option enabled.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, IWLWIFI_LEGACY has to be selected independently before the
drivers are made available.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In commit 13583b1659 ("PCI: refactor io size calculation code") Ram
had a thinko in the refactorization of the code: the end result used the
variable 'align' for the bus alignment, but the original code used
'min_align'.
Since then, another use of that 'align' variable got introduced by
commit c8adf9a3e8 ("PCI: pre-allocate additional resources to devices
only after successful allocation of essential resources.")
Fix both of those uses to use 'min_align' as they should.
Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Ram Pai <linuxram@us.ibm.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
This patch adds support for SMSC's LAN9530, LAN9730 and LAN89530 USB
ethernet controllers to the existing smsc95xx driver by adding
their new USB VID/PID pairs.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conversion.
This also enables toggling TX VLAN offload and fixes TX checksumming
race with offload changes.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes possible race when changing receive checksum state
and removes IPV6_CSUM_GEN_HACK as it's always set.
BTW, The claim about fake IPV6 checksum looks dubious. If that were true,
then there's a problem in networking core and should be fixed there and not
in random drivers.
BTW#2, there's no MAINTAINERS entry for this driver. I assume this driver
is supported by Micrel?
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also removes TSO as it's made fully in software --- better to leave this
to networking core.
If the MAC features can be detected at probe time and not at open, then
stmmac_fix_features could be simplified by limiting hw_features. That's
also better for users as they don't see offloads being togglable but
never turned on.
Redundant fallbacks for TX csum are removed as it's already handled
by network core.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple conversion with a bit of needed cleanup.
This also fixes:
- confusion around vlan_features in rtl8169_vlan_mode(),
- problem with broken TSO for too big MTU (the limit is set
at 0xFFF --- max MSS field value).
SG+IP_CSUM+TSO is left disabled by default, based on suggestion by
David Dillow.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>