Also remove PFUZE_NUM to avoid below build warnings:
CC [M] drivers/regulator/pfuze100-regulator.o
drivers/regulator/pfuze100-regulator.c:86:2: warning: excess elements in array initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:86:2: warning: (near initialization for 'pfuze_device_id') [enabled by default]
drivers/regulator/pfuze100-regulator.c:93:2: warning: excess elements in array initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:93:2: warning: (near initialization for 'pfuze_dt_ids') [enabled by default]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
support pfuze200 chip which remove SW1C and SW4 based on pfuze100.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove __initconst from regulator_desc array because this array is used
during probe and s2mps11_pmic_probe() is not in __init section. However
still select the number of supported regulators according to device ID
so the driver will be ready for adding support for S2MPS14 device.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The regulator core supports this to allow the configuration to be inspected
at runtime even if no software management is enabled.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add __initconst to 'regulator_desc' array with supported regulators.
During probe choose how many and which regulators will be supported
according to device ID. Then copy the 'regulator_desc' array to
allocated memory so the regulator core can use it.
Additionally allocate array of of_regulator_match() dynamically (based
on number of regulators) instead of allocation on the stack.
This is needed for supporting different devices in s2mps11
driver and actually prepares the regulator driver for supporting the
S2MPS14 device.
Code for supporting the S2MPS14 device will add its own array of
'regulator_desc' (also marked as __initconst). This way memory footprint
of the driver will be reduced (approximately 'regulators_desc' array for
S2MPS11 occupies 5 kB on 32-bit ARM, for S2MPS14 will occupy 3 kB).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Yadwinder Singh Brar <yadi.brar01@gmail.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Constify the regulator_desc 'regulators' array.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Regulators registered by devm_regulator_register() do not have to be
stored in state container because they are never dereferenced later.
The array of regulator_dev can be safely removed from state container.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The nodes of regulators should be retrieved from parent device.
Bug was be introduced by commit (regulator: mc13xxx: Fix NULL
pointer error in non-DT mode) in conjuction with (mfd: Revert
"mfd: Always assign of_node in mfd_add_device()").
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix indent code style in order to fix the following checkpatch
issues.
ERROR: code indent should use tabs where possible
WARNING: please, no space before tabs
WARNING: please, no spaces at the start of a line
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Regulator dummy does not have any enable operations. So it is always_on.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a check to avoid NULL pointer dereference error when
booted in non-DT mode. While at it also remove the additional
of_node_get which is no longer needed for of_get_child_by_name
and fix the node pointer.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reported-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are many places where ops->disable is called directly. Instead we
should use _regulator_do_disable() which also handles gpio regulators.
To be able to use the wrapper function from _regulator_force_disable(),
I moved the _notifier_call_chain() call from _regulator_do_disable() to
_regulator_disable(). This way, _regulator_force_disable() can use
different flags for _notifier_call_chain() without calling it twice.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are some direct ops->enable in the regulator core driver. This is
a potential issue as the function _regulator_do_enable() handles gpio
regulators and the normal ops->enable calls. These gpio regulators are
simply ignored when ops->enable is called directly.
One possible bug is that boot-on and always-on gpio regulators are not
enabled on registration.
This patch replaces all ops->enable calls by _regulator_do_enable.
[Handle missing enable operations -- broonie]
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator: Handle invalid enable operation for always/boot on regulators
Signed-off-by: Mark Brown <broonie@linaro.org>
If of_node_get() fails, we should return an error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes bug introduced in 667a6b7a (regulator: max14577: Add missing
of_node_put). The DTS parsing function returned number of matched
regulators as success status which then was compared against 0 in probe.
Result was a probe fail after successful parsing the DTS:
max14577-regulator: probe of max14577-regulator failed with error 2
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviwed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Change "dummy supplies not allowed" error message to warning instead, as this
is a just warning message with no change to the behavior.
[Added a CC to stable since some other bug fixes cause this to come up
more frequently on PCs which is how it was noticed -- broonie]
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
kzalloc prints its own OOM message upon failure.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Propagate the error value returned by the function instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Propagate the error values returned by the function instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Propagate the error values returned by the function instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Propagate the error value returned by the function instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Propagate the error values returned by the function instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Propagate the error value returned by the function instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Propagate the error value returned by the function instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some LDOs and DCDCs have a fixed ramp speed of 6.25 mV/µs. This patch adds
the set_voltage_time_sel function to let consumers know about this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a DT-only driver, so make it depend on OF and remove of_match_ptr in
the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code uses devm_regulator_register() so the we don't need to explicitly
call regulator_unregister() in .remove.
And then we don't need to save rdev pointer to tps->rdev[id].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes below build error:
FATAL: drivers/regulator/tps65218-regulator: struct of_device_id is not terminated with a NULL entry!
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Propagate the error value returned by the function instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit d7857c42 (regulator: pfuze100: Use of_get_child_by_name) we get
the following probe failure:
pfuze100-regulator 1-0008: Full layer: 1, Metal layer: 0
pfuze100-regulator 1-0008: FAB: 0, FIN: 0
pfuze100-regulator 1-0008: regulators node not found
pfuze100-regulator: probe of 1-0008 failed with error -22
Now that of_get_child_by_name() is used we should adjust the device_node pointer
'np' to not get the parent node anymore.
Suggested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ARM, PU, and SOC LDOs in the i.MX6 PMU can operate
in bypass mode. This allows to use external switching
regulators for cpu voltage scaling.
Since bypass and power gating modes are not configured
with their own bits, but via the voltage target bitfield,
store bypass state to be restored when reenabling the
regulator.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ARM, PU, and SOC LDOs in the i.MX6 PMU can completely gate
their power output. Since power gating is configured by writing
zero to the voltage target bitfield,, store a copy of the
voltage selector to be restored when reenabling the regulator.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for TPS65218 PMIC regulators.
The regulators set consists of 6 DCDCs and 1 LDO. The output
voltages are configurable and are meant to supply power to the
main processor and other components.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 934624d6e9 ("regulator: gpio-regulator: do not open-code counting
and access of dt array elements") forgot to convert the recently added
gpios-states property using the same pattern.
Convert this instance to use the of-helpers too, resolving the build error.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bqreaders.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Open coding the counting of elements in a dt-property is abstracted by the newly
introduced of_property_count_uXX_elems functions. Additionally the raw iteration
over the states element exposes the endian conversion and dtb-format details,
which according to Mark Rutland "would be nice to limit [...] to of_ helper
functions".
Thus change ti-abb-regulator to use the helper for element counting and
of_property_read_u32_index for retrieval of individual values.
This makes it possible to remove the raw access to the property entirely.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bqreaders.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Open coding the counting of elements in a dt-property is abstracted by the newly
introduced of_property_count_uXX_elems functions. Additionally the raw iteration
over the states element exposes the endian conversion and dtb-format details,
which according to Mark Rutland "would be nice to limit [...] to of_ helper
functions".
Thus change gpio-regulator to use the helper for element counting and
of_property_read_u32_index for retrieval of individual values.
This makes it possible to remove the raw access to the states property entirely.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bqreaders.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Bug fix to allow the setting of maximum voltage for certain LDOs.
What the bug is:
There is a problem caused by an invalid calculation of n_voltages
in the driver. This n_voltages value has the potential to be
different for each regulator.
The value for linear_min_sel is set as DA9063_V##regl_name#
which can be different depending upon the regulator. This is
chosen according to the following definitions in the DA9063
registers.h file:
DA9063_VLDO1_BIAS 0
DA9063_VLDO2_BIAS 0
DA9063_VLDO3_BIAS 0
DA9063_VLDO4_BIAS 0
DA9063_VLDO5_BIAS 2
DA9063_VLDO6_BIAS 2
DA9063_VLDO7_BIAS 2
DA9063_VLDO8_BIAS 2
DA9063_VLDO9_BIAS 3
DA9063_VLDO10_BIAS 2
DA9063_VLDO11_BIAS 2
The calculation for n_voltages is valid for LDOs whose BIAS value
is zero but this is not correct for those LDOs which have a
non-zero value.
What the fix is:
In order to take into account the non-zero linear_min_sel value which
is set for the regulators LDO5, LDO6, LDO7, LDO8, LDO9, LDO10 and
LDO11, the calculation for n_voltages should take into account the
missing term defined by DA9063_V##regl_name#.
This will in turn allow the core constraints calculation to set the
maximum voltage limits correctly and therefore allow users to apply
the maximum expected voltage to all of the LDOs.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
da9055_regulator_dt_init does not declare return type and it cause
following build warning.
drivers/regulator/da9055-regulator.c:582:15: warning:
return type defaults to ‘int’ [-Wreturn-type]
static inline da9055_regulator_dt_init(struct platform_device *pdev,
^
Fix the warning by declare return type as int exclusively.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Axel Lin