If renesas_usbhs is probed as autonomy mode,
phy reset should be called after power resumed,
and manual cold-plug should be called with slight delay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
suspend/resume will failed on renesas_usbhs without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot unconditionally access any usb-serial port specific
data from the interface driver. Both supending and resuming
may happen after the port has been removed and portdata is
freed.
Treat ports with no portdata as closed ports to avoid a NULL
pointer dereference on resume. No need to kill URBs for
removed ports on suspend, avoiding the same NULL pointer
reference there.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some usb-serial drivers may access port data in their suspend/
resume functions. Such drivers must always verify the validity
of the data as both suspend and resume can be called both before
usb_serial_device_probe and after usb_serial_device_remove.
But the port data may be invalidated during port_probe and
port_remove. This patch prevents the race against suspend and
resume by disabling suspend while port_probe or port_remove is
running.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Use the buffer content length as opposed to the total buffer size. This can
be a real problem when using the mos7840 as a usb serial-console as all
kernel output is truncated during boot.
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb message must be saved also in case the USB endpoint is not a
control endpoint (i.e., "endpoint 0"), otherwise in some circumstances
we don't have a payload in case of error.
The patch has been created by tracing with usbmon the different error
messages generated by this driver with respect to the ehci-hcd driver.
Signed-off-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Tested-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit 354ab8567a titled
"Fix OMAP EHCI suspend/resume failure (i693)" is causing
the usb hub and device detection fails in beagle XM
causeing NFS not functional. This affects the core retention too.
The same commit logic needs to be revisted adhering to hwmod and
device tree framework.
for now, this commit id 354ab8567a
titled "Fix OMAP EHCI suspend/resume failure (i693)" reverted.
This patch is validated on BeagleXM with NFS support over
usb ethernet and USB mass storage and other device detection.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit "5e0aa49 usb: chipidea: use generic map/unmap routines",
the udc part of the chipidea driver needs the generic usb gadget helper
functions. If the chipidea driver with udc support is built into the
kernel and usb gadget is built a module, the linking of the kernel
fails with:
drivers/built-in.o: In function `_hardware_dequeue':
drivers/usb/chipidea/udc.c:527:
undefined reference to `usb_gadget_unmap_request'
drivers/usb/chipidea/udc.c:1269:
undefined reference to `usb_gadget_unmap_request'
drivers/usb/chipidea/udc.c:1821:
undefined reference to `usb_del_gadget_udc'
drivers/usb/chipidea/udc.c:443:
undefined reference to `usb_gadget_map_request'
drivers/usb/chipidea/udc.c:1774:
undefined reference to `usb_add_gadget_udc'
This patch changes the dependencies, so that udc support can only be
activated if the linux gadget support (USB_GADGET) is builtin or both
chipidea driver and USB_GADGET are modular. Same dependencies for the
chipidea host support and the linux host side USB support (USB).
While there, fix the indention of chipidea the help text.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this patch, we add new declarations into option.c to support the new
interfaces of Huawei Data Card devices. And at the same time, remove the
redundant declarations from option.c.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds VID/PID for Kondo Kagaku Co. Ltd. Serial USB Adapter
interface:
http://www.kondo-robot.com/EN/wp/?cat=28
Tested by controlling an RCB3 board using libRCB3.
Signed-off-by: Ozan Çağlayan <ozancag@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS. If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system. Some BIOS will work around this, but not all.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown. The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.
Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names. One example
is Compulab's mini-desktop, the Intense-PC. Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.
The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.
This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Denis Turischev <denis@compulab.co.il>
Tested-by: Denis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org
Hi Greg,
Here's four patches for 3.6. Most are marked for stable as well.
The first one makes the xHCI driver load properly on newer Rensas hosts.
The next two fix issues with the Etron host incorrectly marking short
transfers as successful, and avoiding log warning spam for hosts that
make the same mistake.
The last patch fixes a really nasty xHCI driver bug that could cause
general protection faults when devices stall transfers.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yn5e
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-08-08' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xHCI bug fixes and host quirks.
Hi Greg,
Here's four patches for 3.6. Most are marked for stable as well.
The first one makes the xHCI driver load properly on newer Rensas hosts.
The next two fix issues with the Etron host incorrectly marking short
transfers as successful, and avoiding log warning spam for hosts that
make the same mistake.
The last patch fixes a really nasty xHCI driver bug that could cause
general protection faults when devices stall transfers.
Sarah Sharp
This patch fixes a particularly nasty bug that was revealed by the ring
expansion patches. The bug has been present since the very beginning of
the xHCI driver history, and could have caused general protection faults
from bad memory accesses.
The first thing to note is that a Set TR Dequeue Pointer command can
move the dequeue pointer to a link TRB, if the canceled or stalled
transfer TD ended just before a link TRB. The function to increment the
dequeue pointer, inc_deq, was written before cancellation and stall
support was added. It assumed that the dequeue pointer could never
point to a link TRB. It would unconditionally increment the dequeue
pointer at the start of the function, check if the pointer was now on a
link TRB, and move it to the top of the next segment if so.
This means that if a Set TR Dequeue Point command moved the dequeue
pointer to a link TRB, a subsequent call to inc_deq() would move the
pointer off the segment and into la-la-land. It would then read from
that memory to determine if it was a link TRB. Other functions would
often call inc_deq() until the dequeue pointer matched some other
pointer, which means this function would quite happily read all of
system memory before wrapping around to the right pointer value.
Often, there would be another endpoint segment from a different ring
allocated from the same DMA pool, which would be contiguous to the
segment inc_deq just stepped off of. inc_deq would eventually find the
link TRB in that segment, and blindly move the dequeue pointer back to
the top of the correct ring segment.
The only reason the original code worked at all is because there was
only one ring segment. With the ring expansion patches, the dequeue
pointer would eventually wrap into place, but the dequeue segment would
be out-of-sync. On the second TD after the dequeue pointer was moved to
a link TRB, trb_in_td() would fail (because the dequeue pointer and
dequeue segment were out-of-sync), and this message would appear:
ERROR Transfer event TRB DMA ptr not part of current TD
This fixes bugzilla entry 4333 (option-based modem unhappy on USB 3.0
port: "Transfer event TRB DMA ptr not part of current TD", "rejecting
I/O to offline device"),
https://bugzilla.kernel.org/show_bug.cgi?id=43333
and possibly other general protection fault bugs as well.
This patch should be backported to kernels as old as 2.6.31. A separate
patch will be created for kernels older than 3.4, since inc_deq was
modified in 3.4 and this patch will not apply.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Tested-by: Matthew Hall <mhall@mhcomputing.net>
Cc: stable@vger.kernel.org
Commit c2e935a7d "USB: move transceiver from ehci_hcd and ohci_hcd to
hcd and rename it as phy" removed the last use of the "ohci" variable
in the usb_hcd_omap_remove function, but left the variable in place
unused.
Without this patch, building omap1_defconfig results in:
In file included from drivers/usb/host/ohci-hcd.c:1013:0:
drivers/usb/host/ohci-omap.c: In function 'usb_hcd_omap_remove':
drivers/usb/host/ohci-omap.c:406:19: warning: unused variable 'ohci' [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Richard Zhao <richard.zhao@freescale.com>
When we encounter an xHCI host that needs the XHCI_TRUST_TX_LENGTH
quirk, the xHCI driver ends up spewing messages about the quirk into
dmesg every time a short packet occurs. Change the xHCI driver to
rate-limit such warnings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Matthew Hall <mhall@mhcomputing.net>
Reported-by: Gary E. Miller <gem@rellim.com>
Gary reports that with recent kernels, he notices more xHCI driver
warnings:
xhci_hcd 0000:03:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
We think his Etron xHCI host controller may have the same buggy behavior
as the Fresco Logic xHCI host. When a short transfer is received, the
host will mark the transfer as successfully completed when it should be
marking it with a short completion.
Fix this by turning on the XHCI_TRUST_TX_LENGTH quirk when the Etron
host is discovered. Note that Gary has revision 1, but if Etron fixes
this bug in future revisions, the quirk will have no effect.
This patch should be backported to kernels as old as 2.6.36, that
contain a backported version of commit
1530bbc627 "xhci: Add new short TX quirk
for Fresco Logic host."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Gary E. Miller <gem@rellim.com>
Cc: stable@vger.kernel.org
The NEC/Renesas 720201 xHCI host controller does not complete its reset
within 250 milliseconds. In fact, it takes about 9 seconds to reset the
host controller, and 1 second for the host to be ready for doorbell
rings. Extend the reset and CNR polling timeout to 10 seconds each.
This patch should be backported to kernels as old as 2.6.31, that
contain the commit 66d4eadd8d "USB: xhci:
BIOS handoff and HW initialization."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Edwin Klein Mentink <e.kleinmentink@zonnet.nl>
Cc: stable@vger.kernel.org
usb-dbgp - increase the controller wait time to come out of halt.
kdb - Remove unused KDB_FLAG_ONLY_DO_DUMP code and cpu in more prompt
debug core - pass NMI type on archs that provide NMI types
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LAWq
-----END PGP SIGNATURE-----
Merge tag 'for_linux-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB/usb-dbgp fixes and cleanups from Jason Wessel:
"There are no new features, those will be delayed to the 3.7 window.
There are only fixes/cleanup against the usual kernel churn and we are
removing more lines than we add:
- usb-dbgp - increase the controller wait time to come out of halt.
- kdb - Remove unused KDB_FLAG_ONLY_DO_DUMP code and cpu in more prompt
- debug core - pass NMI type on archs that provide NMI types"
* tag 'for_linux-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
USB: echi-dbgp: increase the controller wait time to come out of halt.
kernel/debug: Make use of KGDB_REASON_NMI
kdb: Remove cpu from the more prompt
kdb: Remove unused KDB_FLAG_ONLY_DO_DUMP
The clock need to be enabled before the musb_core platform device is
created and registered.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We are overwriting the resource->name to "mc" so that musb_core.c
can understand it but this is also changing the platform device's
resource->name as the "name" address remains same.
Fixing the same by changing the resource->name field of local
structure only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit "bb6abcf: ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to
SOC_AM33XX" and "3395955: ARM: OMAP2+: Kconfig: convert
SOC_OMAPTI81XX to SOC_TI81XX" has changed the SOC config for AM33XX
and TI81XX as shown below
CONFIG_SOC_OMAPAM33XX --> CONFIG_SOC_AM33XX
CONFIG_SOC_OMAPTI81XX --> CONFIG_SOC_TI81XX
So updating the same at musb driver for AM33XX and TI81XX platforms.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull second vfs pile from Al Viro:
"The stuff in there: fsfreeze deadlock fixes by Jan (essentially, the
deadlock reproduced by xfstests 068), symlink and hardlink restriction
patches, plus assorted cleanups and fixes.
Note that another fsfreeze deadlock (emergency thaw one) is *not*
dealt with - the series by Fernando conflicts a lot with Jan's, breaks
userland ABI (FIFREEZE semantics gets changed) and trades the deadlock
for massive vfsmount leak; this is going to be handled next cycle.
There probably will be another pull request, but that stuff won't be
in it."
Fix up trivial conflicts due to unrelated changes next to each other in
drivers/{staging/gdm72xx/usb_boot.c, usb/gadget/storage_common.c}
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
delousing target_core_file a bit
Documentation: Correct s_umount state for freeze_fs/unfreeze_fs
fs: Remove old freezing mechanism
ext2: Implement freezing
btrfs: Convert to new freezing mechanism
nilfs2: Convert to new freezing mechanism
ntfs: Convert to new freezing mechanism
fuse: Convert to new freezing mechanism
gfs2: Convert to new freezing mechanism
ocfs2: Convert to new freezing mechanism
xfs: Convert to new freezing code
ext4: Convert to new freezing mechanism
fs: Protect write paths by sb_start_write - sb_end_write
fs: Skip atime update on frozen filesystem
fs: Add freezing handling to mnt_want_write() / mnt_drop_write()
fs: Improve filesystem freezing handling
switch the protection of percpu_counter list to spinlock
nfsd: Push mnt_want_write() outside of i_mutex
btrfs: Push mnt_want_write() outside of i_mutex
fat: Push mnt_want_write() outside of i_mutex
...
Merge Andrew's second set of patches:
- MM
- a few random fixes
- a couple of RTC leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (120 commits)
rtc/rtc-88pm80x: remove unneed devm_kfree
rtc/rtc-88pm80x: assign ret only when rtc_register_driver fails
mm: hugetlbfs: close race during teardown of hugetlbfs shared page tables
tmpfs: distribute interleave better across nodes
mm: remove redundant initialization
mm: warn if pg_data_t isn't initialized with zero
mips: zero out pg_data_t when it's allocated
memcg: gix memory accounting scalability in shrink_page_list
mm/sparse: remove index_init_lock
mm/sparse: more checks on mem_section number
mm/sparse: optimize sparse_index_alloc
memcg: add mem_cgroup_from_css() helper
memcg: further prevent OOM with too many dirty pages
memcg: prevent OOM with too many dirty pages
mm: mmu_notifier: fix freed page still mapped in secondary MMU
mm: memcg: only check anon swapin page charges for swap cache
mm: memcg: only check swap cache pages for repeated charging
mm: memcg: split swapin charge function into private and public part
mm: memcg: remove needless !mm fixup to init_mm when charging
mm: memcg: remove unneeded shmem charge type
...
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
The skb->pfmemalloc flag gets set to true iff during the slab allocation
of data in __alloc_skb that the the PFMEMALLOC reserves were used. If
page splitting is used, it is possible that pages will be allocated from
the PFMEMALLOC reserve without propagating this information to the skb.
This patch propagates page->pfmemalloc from pages allocated for fragments
to the skb.
It works by reintroducing and expanding the skb_alloc_page() API to take
an skb. If the page was allocated from pfmemalloc reserves, it is
automatically copied. If the driver allocates the page before the skb, it
should call skb_propagate_pfmemalloc() after the skb is allocated to
ensure the flag is copied properly.
Failure to do so is not critical. The resulting driver may perform slower
if it is used for swap-over-NBD or swap-over-NFS but it should not result
in failure.
[davem@davemloft.net: API rename and consistency]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default 10 microsecond delay for the controller to come out of
halt in dbgp_ehci_startup is too short, so increase it to 1 millisecond.
This is based on emperical testing on various USB debug ports on
modern machines such as a Lenovo X220i and an Ivybridge development
platform that needed to wait ~450-950 microseconds.
Cc: <stable@vger.kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.
musb also has these dummy macros defined locally. Remove them as they
aren't required anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac9651: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
sigh...
* opened files have non-NULL dentries and non-NULL inodes
* close_filp() needs current->files only if the file had been
in descriptor table.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
A mixed bag of fixes, some for merge window fallout (tegra, MXS), and
a short series of fixes for marvell platforms that didn't make it in
before 3.5.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HZB3
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A mixed bag of fixes, some for merge window fallout (tegra, MXS), and
a short series of fixes for marvell platforms that didn't make it in
before 3.5."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: fix compile error caused by prom_update_property change
ARM: dt: tegra trimslice: enable USB2 port
ARM: dt: tegra trimslice: add vbus-gpio property
ARM: vt8500: Add maintainer for VT8500 architecture
ARM: Kirkwood: Replace mrvl with marvell
ARM: Orion: fix driver probe error handling with respect to clk
ARM: Dove: Fixup ge00 initialisation
ARM: Kirkwood: Fix PHY disable clk problems
ARM: Kirkwood: Ensure runit clock always ticks.
ARM: versatile: Don't use platform clock for Integrator & VE
ARM: tegra: harmony: add regulator supply name and its input supply
Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and drivers.
There's some scsi changes that I think also went in through the scsi tree, but
they merge just fine. All of these patches have been in the linux-next tree
for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAQhpcACgkQMUfUDdst+yms4wCgpMbfFYTZ8lHpDnXHYFv6qw8j
FIsAmwT4mbT7m8C0k+ELV/5T2e0eYJEQ
=QetG
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and
drivers. There's some scsi changes that I think also went in through
the scsi tree, but they merge just fine. All of these patches have
been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up trivial conflicts in include/scsi/scsi_device.h (same libata
conflict that Jeff had already encountered)
* tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams
usb: Add quirk detection based on interface information
usb: s3c-hsotg: Add header file protection macros in s3c-hsotg.h
USB: ehci-s5p: Add vbus setup function to the s5p ehci glue layer
USB: add USB_VENDOR_AND_INTERFACE_INFO() macro
USB: notify phy when root hub port connect change
USB: remove 8 bytes of padding from usb_host_interface on 64 bit builds
USB: option: add ZTE MF821D
USB: sierra: QMI mode MC7710 moved to qcserial
USB: qcserial: adding Sierra Wireless devices
USB: qcserial: support generic Qualcomm serial ports
USB: qcserial: make probe more flexible
USB: qcserial: centralize probe exit path
USB: qcserial: consolidate usb_set_interface calls
USB: ehci-s5p: Add support for device tree
USB: ohci-exynos: Add support for device tree
USB: ehci-omap: fix compile failure(v1)
usb: host: tegra: pass correct pointer in ehci_setup()
USB: ehci-fsl: Update ifdef check to work on 64-bit ppc
USB: serial: keyspan: Removed unrequired parentheses.
...
The clk patches added code to get and enable clocks in the
respective driver probe functions. If the probe function failed
for some reason after enabling the clock, the clock was not
disabled again in many cases.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lumm <andrew@lunn.ch>
The most important feature of this patch set is the new async infrastructure
that makes sure async_synchronize_full() synchronizes all domains and allows
us to remove all the hacks (like having scsi_complete_async_scans() in the
device base code) and means that the async infrastructure will "just work" in
future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
/uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
=y2sh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
Pull slave-dmaengine update from Vinod Koul:
"This time we have a new dmaengine driver from the tegra folks. Also
we have Guennadi's cleanup of sh drivers which incudes a library for
sh drivers. And the usual odd fixes in bunch of drivers and some nice
cleanup of dw_dmac from Andy."
Fix up conflicts in drivers/mmc/host/sh_mmcif.c
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Cleanup logging messages
mmc: sh_mmcif: switch to the new DMA channel allocation and configuration
dma: sh: provide a migration path for slave drivers to stop using .private
dma: sh: use an integer slave ID to improve API compatibility
dmaengine: shdma: prepare to stop using struct dma_chan::private
sh: remove unused DMA device pointer from SIU platform data
ASoC: siu: don't use DMA device for channel filtering
dmaengine: shdma: (cosmetic) simplify a static function
dmaengine: at_hdmac: add a few const qualifiers
dw_dmac: use 'u32' for LLI structure members, not dma_addr_t
dw_dmac: mark dwc_dump_lli inline
dma: mxs-dma: Export missing symbols from mxs-dma.c
dma: shdma: convert to the shdma base library
ASoC: fsi: prepare for conversion to the shdma base library
usb: renesas_usbhs: prepare for conversion to the shdma base library
ASoC: siu: prepare for conversion to the shdma base library
serial: sh-sci: prepare for conversion to the shdma base library
mmc: sh_mobile_sdhi: prepare for conversion to the shdma base library
mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
dma: shdma: prepare for conversion to the shdma base library
...
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
Pull networking changes from David S Miller:
1) Remove the ipv4 routing cache. Now lookups go directly into the FIB
trie and use prebuilt routes cached there.
No more garbage collection, no more rDOS attacks on the routing
cache. Instead we now get predictable and consistent performance,
no matter what the pattern of traffic we service.
This has been almost 2 years in the making. Special thanks to
Julian Anastasov, Eric Dumazet, Steffen Klassert, and others who
have helped along the way.
I'm sure that with a change of this magnitude there will be some
kind of fallout, but such things ought the be simple to fix at this
point. Luckily I'm not European so I'll be around all of August to
fix things :-)
The major stages of this work here are each fronted by a forced
merge commit whose commit message contains a top-level description
of the motivations and implementation issues.
2) Pre-demux of established ipv4 TCP sockets, saves a route demux on
input.
3) TCP SYN/ACK performance tweaks from Eric Dumazet.
4) Add namespace support for netfilter L4 conntrack helpers, from Gao
Feng.
5) Add config mechanism for Energy Efficient Ethernet to ethtool, from
Yuval Mintz.
6) Remove quadratic behavior from /proc/net/unix, from Eric Dumazet.
7) Support for connection tracker helpers in userspace, from Pablo
Neira Ayuso.
8) Allow userspace driven TX load balancing functions in TEAM driver,
from Jiri Pirko.
9) Kill off NLMSG_PUT and RTA_PUT macros, more gross stuff with
embedded gotos.
10) TCP Small Queues, essentially minimize the amount of TCP data queued
up in the packet scheduler layer. Whereas the existing BQL (Byte
Queue Limits) limits the pkt_sched --> netdevice queuing levels,
this controls the TCP --> pkt_sched queueing levels.
From Eric Dumazet.
11) Reduce the number of get_page/put_page ops done on SKB fragments,
from Alexander Duyck.
12) Implement protection against blind resets in TCP (RFC 5961), from
Eric Dumazet.
13) Support the client side of TCP Fast Open, basically the ability to
send data in the SYN exchange, from Yuchung Cheng.
Basically, the sender queues up data with a sendmsg() call using
MSG_FASTOPEN, then they do the connect() which emits the queued up
fastopen data.
14) Avoid all the problems we get into in TCP when timers or PMTU events
hit a locked socket. The TCP Small Queues changes added a
tcp_release_cb() that allows us to queue work up to the
release_sock() caller, and that's what we use here too. From Eric
Dumazet.
15) Zero copy on TX support for TUN driver, from Michael S. Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1870 commits)
genetlink: define lockdep_genl_is_held() when CONFIG_LOCKDEP
r8169: revert "add byte queue limit support".
ipv4: Change rt->rt_iif encoding.
net: Make skb->skb_iif always track skb->dev
ipv4: Prepare for change of rt->rt_iif encoding.
ipv4: Remove all RTCF_DIRECTSRC handliing.
ipv4: Really ignore ICMP address requests/replies.
decnet: Don't set RTCF_DIRECTSRC.
net/ipv4/ip_vti.c: Fix __rcu warnings detected by sparse.
ipv4: Remove redundant assignment
rds: set correct msg_namelen
openvswitch: potential NULL deref in sample()
tcp: dont drop MTU reduction indications
bnx2x: Add new 57840 device IDs
tcp: avoid oops in tcp_metrics and reset tcpm_stamp
niu: Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return value
niu: Fix to check for dma mapping errors.
net: Fix references to out-of-scope variables in put_cmsg_compat()
net: ethernet: davinci_emac: add pm_runtime support
net: ethernet: davinci_emac: Remove unnecessary #include
...
Pull arch/tile updates from Chris Metcalf:
"These changes provide support for PCIe root complex and USB host mode
for tilegx's on-chip I/Os.
In addition, this pull provides the required underpinning for the
on-chip networking support that was pulled into 3.5. The changes have
all been through LKML (with several rounds for PCIe RC) and on
linux-next."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: updates to pci root complex from community feedback
bounce: allow use of bounce pool via config option
usb: add host support for the tilegx architecture
arch/tile: provide kernel support for the tilegx USB shim
tile pci: enable IOMMU to support DMA for legacy devices
arch/tile: enable ZONE_DMA for tilegx
tilegx pci: support I/O to arbitrarily-cached pages
tile: remove unused header
arch/tile: tilegx PCI root complex support
arch/tile: provide kernel support for the tilegx TRIO shim
arch/tile: break out the "csum a long" function to <asm/checksum.h>
arch/tile: provide kernel support for the tilegx mPIPE shim
arch/tile: common DMA code for the GXIO IORPC subsystem
arch/tile: support MMIO-based readb/writeb etc.
arch/tile: introduce GXIO IORPC framework for tilegx
Clock support is moving to the clk subsystem. These tegra, omap and imx
changes are for code that is still platform specific and not (yet)
part of that subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Cvpa
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clk changes from Arnd Bergmann:
"Clock support is moving to the clk subsystem. These tegra, omap and
imx changes are for code that is still platform specific and not (yet)
part of that subsystem."
Fix up conflicts in arch/arm/mach-{imx/clk-imx51-imx53.c,omap2/Makefile}
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: imx: clk-imx31: Fix clock id for rnga driver
ARM: imx: add missing item to the list of clock event modes
ARM: i.MX5x CSPI: Fixed clock name for CSPI
ARM: i.MX5x clocks: Fix GPT clocks
ARM: i.MX5x clocks: Fix parent for PWM clocks
ARM: i.MX5x clocks: Add EPIT support
ARM: mx27: Reenable silicon version print
ARM: clk-imx27: Fix rtc clock id
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: OMAP3+: clock33xx: Add AM33XX clock tree data
ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
...
These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should
not be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4zvd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull general arm-soc cleanups from Arnd Bergmann:
"These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should not
be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra."
Resolve trivial conflict in arch/arm/mach-omap2/clockdomains3xxx_data.c
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
ARM: S3C24XX: Remove unused GPIO definitions for Openmoko GTA02 board
ARM: S3C24XX: Remove unused GPIO definitions for port J
ARM: S3C24XX: Remove unused GPA, GPE, GPH bank GPIO aliases
ARM: S3C24XX: Convert the touchscreen setup code to common GPIO API
ARM: S3C24XX: Convert the PM code to gpiolib API
ARM: S3C24XX: Convert QT2410 board file to the gpiolib API
ARM: S3C24XX: Convert SMDK board file to the gpiolib API
ARM: S3C24XX: Free the backlight gpio requested in Mini2440 board code
ARM: imx: remove unused pdata from device macros
ARM: imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX_SSI from MACH_MX25_3DS
ARM: at91: fix new build errors
ARM: at91: add AIC5 support
ARM: at91: remove mach/irqs.h
ARM: at91: sparse irq support
ARM: at91: at91 based machines specify their own irq handler at run time
ARM: at91: remove static irq priorities for sam9x5
ARM: at91: add of irq priorities support
...
Pull target updates from Nicholas Bellinger:
"There have been lots of work in a number of areas this past round.
The highlights include:
- Break out target_core_cdb.c emulation into SPC/SBC ops (hch)
- Add a parse_cdb method to target backend drivers (hch)
- Move sync_cache + write_same + unmap into spc_ops (hch)
- Use target_execute_cmd for WRITEs in iscsi_target + srpt (hch)
- Offload WRITE I/O backend submission in tcm_qla2xxx + tcm_fc (hch +
nab)
- Refactor core_update_device_list_for_node() into enable/disable
funcs (agrover)
- Replace the TCM processing thread with a TMR work queue (hch)
- Fix regression in transport_add_device_to_core_hba from TMR
conversion (DanC)
- Remove racy, now-redundant check of sess_tearing_down with qla2xxx
(roland)
- Add range checking, fix reading of data len + possible underflow in
UNMAP (roland)
- Allow for target_submit_cmd() returning errors + convert fabrics
(roland + nab)
- Drop bogus struct file usage for iSCSI/SCTP (viro)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (54 commits)
iscsi-target: Drop bogus struct file usage for iSCSI/SCTP
target: NULL dereference on error path
target: Allow for target_submit_cmd() returning errors
target: Check number of unmap descriptors against our limit
target: Fix possible integer underflow in UNMAP emulation
target: Fix reading of data length fields for UNMAP commands
target: Add range checking to UNMAP emulation
target: Add generation of LOGICAL BLOCK ADDRESS OUT OF RANGE
target: Make unnecessarily global se_dev_align_max_sectors() static
target: Remove se_session.sess_wait_list
qla2xxx: Remove racy, now-redundant check of sess_tearing_down
target: Check sess_tearing_down in target_get_sess_cmd()
sbp-target: Consolidate duplicated error path code in sbp_handle_command()
target: Un-export target_get_sess_cmd()
qla2xxx: Get rid of redundant qla_tgt_sess.tearing_down
target: Make core_disable_device_list_for_node use pre-refactoring lock ordering
target: refactor core_update_device_list_for_node()
target: Eliminate else using boolean logic
target: Misc retval cleanups
target: Remove hba param from core_dev_add_lun
...
Update information of Seagate Portable HDD and WD My Passport HDD in
quirk list.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support for write cache quirk on usb hdd. scsi driver will be set to wce
by detecting write cache quirk in quirk list when plugging usb hdd.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Most Logitech UVC webcams (both early models that don't advertise UVC
compatibility and newer UVC-advertised devices) require the RESET_RESUME
quirk. Instead of listing each and every model, match the devices based
on the UVC interface information.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a whole class of devices (possibly from a specific vendor, or
across multiple vendors) require a quirk, explictly listing all devices
in the class make the quirks table unnecessarily large. Fix this by
allowing matching devices based on interface information.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Felipe Balbi <balbi@ti.com>
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Felipe Balbi <balbi@ti.com>
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule.
The flag was only commented-out in the driver, but we should just
remove it altogether.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Felipe Balbi <balbi@ti.com>
We want it to be possible for target_submit_cmd() to return errors up
to its fabric module callers. For now just update the prototype to
return an int, and update all callers to handle non-zero return values
as an error.
This is immediately useful for tcm_qla2xxx to fix a long-standing active
I/O session shutdown race, but tcm_fc, usb-gadget, and sbp-target the
fabric maintainers need to check + ACK that handling a target_submit_cmd()
failure due to session shutdown does not introduce regressions
(nab: Respin against for-next after initial NACK + update docbook comment +
fix double se_cmd init in exception path for usb-gadget)
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch retrieves and configures the vbus control gpio via
the device tree. The suspend/resume callbacks will be later
modified for vbus control.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy may need to change settings when port connect change.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove this command submission path which is not used by any in-tree driver.
This also removes the now unused new_cmd_map fabtric method, which a few
drivers implemented despite never calling transport_generic_handle_cdb_map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Just call target_execute_cmd directly. Also, convert loopback, sbp,
usb-gadget to use the newly exported target_execute_cmd().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Sold by O2 (telefonica germany) under the name "LTE4G"
Tested-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MC7710 in QMI mode does not support the vendor
specific USB requests used by this driver. The most
noticable effect of this is a 5 second delay as each
serial port is probed, caused by the set_power_state
command timing out:
[ 17.434291] usbcore: registered new interface driver sierra
[ 17.434383] USB Serial support registered for Sierra USB modem
[ 17.434486] sierra 8-4:1.0: Sierra USB modem converter detected
[ 22.432413] usb 8-4: Sierra USB modem converter now attached to ttyUSB0
[ 22.432563] sierra 8-4:1.2: Sierra USB modem converter detected
[ 27.432410] usb 8-4: Sierra USB modem converter now attached to ttyUSB1
[ 27.432562] sierra 8-4:1.3: Sierra USB modem converter detected
[ 32.432463] usb 8-4: Sierra USB modem converter now attached to ttyUSB2
The MC7710 provide the same Qualcomm serial interfaces
as Gobi modules, and the qcserial driver has been extended
to support the module instead of this driver.
Cc: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QMI mode of the Sierra Wireless MC7710 is close to
a Gobi device, and also identified as one by the
Windows drivers provided by Sony. The serial interfaces
are the same as for any other Gobi module, but the USB
interface layout is different:
0: DM/DIAG (also present in bootloader mode)
2: NMEA
3: AT-capable modem port
8: QMI/net
19: QMI/net (not always present)
20: QMI/net (not always present)
Note in particular that the NMEA and AT ports are reversed
compared to a Gobi 2k+ device, and that the DM port appears
as a QDL port in bootloader mode using the same device ID.
The Sony driver also document two new devices with standard
Gobi 2k+ layout (1199:68a5, 1199:68a9) having a QDL mode
(1199:68a4, 1199:68a8). Adding these as well.
Lenovo Windows drivers document the USB interface layout
for a few additional Sierra Wireless devices. Adding these
while at it:
- MC7770 (1199:901b) with standard Gobi 2k+ layout
- MC7700 (0f3d:68a2) with the same layout as MC7710
- MC7750 (114f:68a2) with the same layout as MC7710
- EM7700 (1199:901c) with the same layout as MC7710
Cc: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to verify the interface layout when doing
interface number based matching. We can safely trust
the device ID table in this case.
This allows the driver to support any USB interface
layout for non-Gobi 1k/2k+ devices.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparing qcprobe support for more than just strict
Gobi 1k or 2k+ devices. Many newer Qualcomm based
devices provide the same serial ports, but using
varying USB interface layouts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Creating a common exit path from qcprobe to make it
easier to extend it.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to replicate the same code all over the place.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to parse probe data for
ehci driver for exynos using device tree
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to parse probe data for
ohci driver for exynos using device tree.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The omap_ehci_init() is introduced in the below commit:
commit 1a49e2ac9651df7349867a5cf44e2c83de1046af(EHCI:
centralize controller initialization)
the local variable of 'pdev' inside omap_ehci_init() is used
but not defined, so fix the compiling failure.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci_setup() require the pointer of usb_hcd.
Passing the correct pointer in place of ehci_hcd
pointer.
This is side effect of change:
commit 1a49e2ac96
Author: Alan Stern <stern@rowland.harvard.edu>
EHCI: centralize controller initialization
[Although I checked for this specifically, obviously I missed some of
the calls. In addition to the mistake in ehci-tegra.c that Laxman
fixed here, the same thing needs to be fixed in ehci-orion.c and
ehci-xls.c. -- Alan Stern]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to use CONFIG_FSL_SOC_BOOKE instead of CONFIG_PPC_85xx as
CONFIG_PPC_85xx isn't defined when we build support for 64-bit embedded
FSL PPC SoCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to conform with checkpatch.sh script. - return is not a
function, parentheses not required. Removed 1 checkpatch.sh error.
Signed-off-by: Ben Minerds <puzzleduck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to conform with checkpatch.sh script. - space near open
parenthesis '('. Removed 2 checkpatch.sh errors.
Signed-off-by: Ben Minerds <puzzleduck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to conform with checkpatch.sh script. - space around '='.
Removed 1 checkpatch.sh error.
Signed-off-by: Ben Minerds <puzzleduck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to conform with checkpatch.sh script. - spaces around '?' and
':'. Removed 14 checkpatch.sh errors.
Signed-off-by: Ben Minerds <puzzleduck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's four bug fix patches for Link PM (LPM), which are marked for
3.5-stable. There's also three patches that turn on Latency Tolerance
Messaging (LTM) for xHCI host controllers and USB 3.0 devices that support
this low power feature.
Please queue for 3.6.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=G1bL
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2012-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
USB: Link PM fixes and Latency Tolerance Messaging
Hi Greg,
Here's four bug fix patches for Link PM (LPM), which are marked for
3.5-stable. There's also three patches that turn on Latency Tolerance
Messaging (LTM) for xHCI host controllers and USB 3.0 devices that support
this low power feature.
Please queue for 3.6.
Sarah Sharp
This patch (as1589) resolves some unlikely races involving system
shutdown or controller death in ehci-hcd:
Shutdown races with both root-hub resume and controller
resume.
Controller death races with root-hub suspend.
A new bitflag is added to indicate that the controller has been shut
down (whether for system shutdown or because it died). Tests are
added in the suspend and resume pathways to avoid reactivating the
controller after any sort of shutdown.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1588) adjusts the locking in ehci-hcd's various halt,
shutdown, and suspend/resume pathways. We want to hold the spinlock
while writing device registers and accessing shared variables, but not
while polling in a loop.
In addition, there's no need to call ehci_work() at times when no URBs
can be active, i.e., in ehci_stop() and ehci_bus_suspend().
Finally, ehci_adjust_port_wakeup_flags() is called only in situations
where interrupts are enabled; therefore it can use spin_lock_irq
rather than spin_lock_irqsave.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1587) simplifies ehci-hcd's scan_isoc() routine by
eliminating some local variables, declaring boolean-valued values as
bool rather than unsigned, changing variable names to make more sense,
and so on.
The logic at the end of the routine is cut down significantly. The
scanning doesn't have to catch up all the way to where the hardware
is; it merely has to catch up to where the hardware was when the last
interrupt occurred. If the hardware has made more progress since then
and issued another interrupt, a rescan will catch up to it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1586) replaces the kernel timer used by ehci-hcd as an
I/O watchdog with an hrtimer event.
Unlike in the current code, the watchdog event is now always enabled
whenever any isochronous URBs are active. This will prevent bugs
caused by the periodic schedule wrapping around with no completion
interrupts; the watchdog handler is guaranteed to scan the isochronous
transfers at least once during each iteration of the schedule. The
extra overhead will be negligible: one timer interrupt every 100 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1585) fixes a bug in ehci-hcd's scheme for scanning
interrupt QHs.
Currently a single routine takes care of scanning everything on the
periodic schedule. Whenever an interrupt occurs, it scans all
isochronous and interrupt URBs scheduled for frames that have elapsed
since the last scan.
This has two disadvantages. The first is relatively minor: An
interrupt QH is likely to end up getting scanned multiple times,
particularly if the last scan was not fairly recent. (The current
code avoids this by maintaining a periodic_stamp in each interrupt
QH.)
The second is more serious. The periodic schedule wraps around. If
the last scan occurred during frame N, and the next scan occurs when
the schedule has gone through an entire cycle and is back at frame N,
the scanning code won't look at any frames other than N. Consequently
it won't see any QHs that completed during frame N-1 or earlier.
The patch replaces the entire frame-based approach for scanning
interrupt QHs with a new routine using a list-based approach, the same
as for async QHs. This has a slight disadvantage, because it means
that all interrupt QHs have to be scanned every time. But it is more
robust than the current approach.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1584) fixes a minor bug that has been present in
ehci-hcd since the beginning.
Scanning the schedules for URB completions is single-threaded. If a
completion interrupt occurs while an URB is being given back, the
interrupt handler realizes that a scan is in progress on another CPU
and avoids starting a new one.
This means that completion events can be lost. If an URB completes
after it has been scanned but while a scan is still in progress, the
driver won't notice and won't rescan the completed URB.
The patch fixes the problem by adding a new flag to indicate that
another scan is needed after the current scan is done. The flag gets
set whenever a completion interrupt occurs while a scan is in
progress. The rescan will see the completion, thus preventing it from
getting lost.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1583) changes ehci-hcd to use an hrtimer event for
unlinking empty (unused) async QHs instead of using a kernel timer.
The check for empty QHs is moved to a new routine, where it doesn't
require going through an entire scan of both the async and periodic
schedules. And it can unlink multiple QHs at once, unlike the current
code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1582) changes ehci-hcd's strategy for unlinking async
QHs. Currently the driver never unlinks more than one QH at a time.
This can be inefficient and cause unnecessary delays, since a QH
cannot be reused while it is waiting to be unlinked.
The new strategy unlinks all the waiting QHs at once. In practice the
improvement won't be very big, because it's somewhat uncommon to have
two or more QHs waiting to be unlinked at any time. But it does
happen, and in any case, doing things this way makes more sense IMO.
The change requires the async unlinking code to be refactored
slightly. Now in addition to the routines for starting and ending an
unlink, there are new routines for unlinking a single QH and starting
an IAA cycle. This approach is needed because there are two separate
paths for unlinking async QHs:
When a transfer error occurs or an URB is cancelled, the QH
must be unlinked right away;
When a QH has been idle sufficiently long, it is unlinked
to avoid consuming DMA bandwidth uselessly.
In the first case we want the unlink to proceed as quickly as
possible, whereas in the second case we can afford to batch several
QHs together and unlink them all at once. Hence the division of
labor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1581) replaces the iaa_watchdog kernel timer used by
ehci-hcd with an hrtimer event, in keeping with the general conversion
to high-res timers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1580) makes ehci_iso_stream structures behave more like
QHs, in that they will remain allocated until their isochronous
endpoint is disabled. This will come in useful in the future, when
periodic bandwidth gets allocated as an altsetting is installed rather
than on-the-fly.
For now, the change to the ehci_iso_stream lifetimes means that each
structure is always deallocated at exactly one spot in
ehci_endpoint_disable() and never used again. As a result, it is no
longer necessary to use reference counting on these things, and the
patch removes it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1579) adds an hrtimer event to handle deallocation of
iTDs and siTDs in ehci-hcd.
Because of the frame-oriented approach used by the EHCI periodic
schedule, the hardware can continue to access the Transfer Descriptor
for isochronous (or split-isochronous) transactions for up to a
millisecond after the transaction completes. The iTD (or siTD) must
not be reused before then.
The strategy currently used involves putting completed iTDs on a list
of cached entries and every so often returning them to the endpoint's
free list. The new strategy reduces overhead by putting completed
iTDs back on the free list immediately, although they are not reused
until it is safe to do so.
When the isochronous endpoint stops (its queue becomes empty), the
iTDs on its free list get moved to a global list, from which they will
be deallocated after a minimum of 2 ms. This delay is what the new
hrtimer event is for.
Overall this may not be a tremendous improvement over the current
code, but to me it seems a lot more clear and logical. In addition,
it removes the need for each iTD to keep a reference to the
ehci_iso_stream it belongs to, since the iTD never needs to be moved
back to the stream's free list from the global list.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1578) adds an hrtimer event to handle the death of an
EHCI controller. When a controller dies, it doesn't necessarily stop
running right away. The new event polls at 1-ms intervals to see when
all activity has safely stopped. This replaces a busy-wait polling
loop in the current code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1577) adds hrtimer support for unlinking interrupt QHs
in ehci-hcd. The current code relies on a fixed delay of either 2 or
55 us, which is not always adequate and in any case is totally bogus.
Thanks to internal caching, the EHCI hardware may continue to access
an interrupt QH for more than a millisecond after it has been unlinked.
In fact, the EHCI spec doesn't say how long to wait before using an
unlinked interrupt QH. The patch sets the delay to 9 microframes
minimum, which ought to be adequate.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1576) adds hrtimer support for managing ehci-hcd's
async schedule. Just as with the earlier change to the periodic
schedule management, two new hrtimer events take care of everything.
One event polls at 1-ms intervals to see when the Asynchronous
Schedule Status (ASS) flag matches the Asynchronous Schedule Enable
(ASE) value; the schedule's state must not be changed until it does.
The other event delays for 15 ms after the async schedule becomes
empty before turning it off.
The new events replace a busy-wait poll and a kernel timer usage.
They also replace the rather illogical method currently used for
indicating the async schedule should be turned off: attempting to
unlink the dedicated QH at the head of the async list.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1575) removes special code added for status polling of
the EHCI controller in PS3 systems. While the controller is running,
the polling is now carried out by an hrtimer handler. When the
controller is suspending or stopping, we use the same polling routine
as the old code -- but in neither case do we need to conclude that the
controller has died if the polling goes on for too long.
As a result the entire handshake_on_error_set_halt() routine is now
unused, so it is removed from the driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1574) changes the return type of multiple functions in
ehci-sched.c from int to void. The values they return are now always
0, so there's no reason for them to return any value at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1573) adds hrtimer support for managing ehci-hcd's
periodic schedule. There are two issues to deal with.
First, the schedule's state (on or off) must not be changed until the
hardware status has caught up with the current command. This is
handled by an hrtimer event that polls at 1-ms intervals to see when
the Periodic Schedule Status (PSS) flag matches the Periodic Schedule
Enable (PSE) value.
Second, the schedule should not be turned off as soon as it becomes
empty. Turning the schedule on and off takes time, so we want to wait
until the schedule has been empty for a suitable period before turning
it off. This is handled by an hrtimer event that gets set to expire
10 ms after the periodic schedule becomes empty.
The existing code polls (for up to 1125 us and with interrupts
disabled!) to check the status, and doesn't implement a delay before
turning off the schedule. Furthermore, if the polling fails then the
driver decides that the controller has died. This has caused problems
for several people; some controllers can take 10 ms or more to turn
off their periodic schedules.
This patch fixes these issues. It also makes the "broken_periodic"
workaround unnecessary; there is no longer any danger of turning off
the periodic schedule after it has been on for less than 1 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1572) begins the conversion of ehci-hcd over to using
high-resolution timers rather than old-fashioned low-resolution kernel
timers. This reduces overhead caused by timer roundoff on systems
where HZ is smaller than 1000. Also, the new timer framework
introduced here is much more logical and easily extended than the
ad-hoc approach ehci-hcd currently uses for timers.
An hrtimer structure is added to ehci_hcd, along with a bitflag array
and an array of ktime_t values, to keep track of which timing events
are pending and what their expiration times are.
Only the infrastructure for the timing operations is added in this
patch. Later patches will add routines for handling each of the
various timing events the driver needs. In some cases the new hrtimer
handlers will replace the existing handlers for ehci-hcd's kernel
timers; as this happens the old timers will be removed. In other
cases the new timing events will replace busy-wait loops.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1571) adds a new state for ehci-hcd's root hubs:
EHCI_RH_STOPPING. This value is used at times when the root hub is
being stopped and we don't know whether or not the hardware has
finished all its DMA yet.
Although the purpose may not be apparent, this distinction will come
in useful later on. Future patches will avoid actions that depend on
the root hub being operational (like turning on the async or periodic
schedules) when they see the state is EHCI_RH_STOPPING.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1570) adds a pointer for the end of ehci-hcd's
async-unlink list. The list (which is actually a queue) is singly
linked, so having a pointer to its end makes adding new entries easier
-- there's no longer any need to scan through the whole list.
In principle it could be changed to a standard doubly-linked list. It
turns out that doing so actually makes the code less clear, so I'm
leaving it as is.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kuninori Morimoto