Tested against a couple of different systems (with different pin
configs), but the others should also work. Also cleaned up some of the
9205 patch code.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added CONFIG_SND_HDA_POWER_SAVE kconfig. It's an experimental option
to achieve an aggressive power-saving. With this option, the driver
will turn on/off the power of each codec and controller chip dynamically
on demand.
The patch introduces a new module option 'power_save'. It specifies
the second of time-out for automatic power-down. As default, it's
10 seconds. Setting 0 means to suppress the power-saving feature.
The codec may have analog-input loopbacks, which are usually represented
by mixer elements such as 'Mic Playback Switch' or 'CD Playback Switch'.
When these are on, we cannot turn off the mixer and the codec chip has
to be kept on. For bookkeeping these states, a new codec-callback is
introduced.
For the bus-controller side, a new callback pm_notify is introduced,
which can be used to turn on/off the contoller appropriately.
Note that this power-saving might cause slight click-noise at
power-on/off. Also, it might take some time to wake up the codec, and
might even drop some tones at the very beginning. This seems to be the
side-effect of turning off the controller chip.
This turn-off of the controller can be disabled by undefining
HDA_POWER_SAVE_RESET_CONTOLLER in hda_intel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
We have already a generic bind-control helper, so let's clean up the codes
using it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added snd_hda_codec_amp_stereo() function that changes both of stereo
channels with the same mask and value bits. It simplifies most of
amp-handling codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
So far, the driver looked the table of snd_kcontrol_new used for creating
mixer elements and forces to call each of its put callbacks in PM resume
code. This is too ugly and hackish.
Now, the resume is simplified using the codec amp and command register
caches. The driver simply restores the values that have been written
in the cache table. With this simplification, most codec support codes
don't require any special resume callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for Dell E520 and a couple of other 965 based systems.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The recent fix for STAC92xx surround outputs broke the input pin
setting for shared line-in and mic jacks. This patch fixes the
breakage.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added support for some boards with SPDIF in/out, and cleaned up the GPIO
enable function.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added support for line out controls for STAC9202 cards, and fixed issue
where master mixer control was being created twice for headphone and
speaker outs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Use ARRAY_SIZE() to calculate the number of pin widgets for each codec
chip.
This also fixes a typo in STAC9205 code that gives a wrong number (14
instead of 12), which resulted in fatal communication errors.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the mismatch of init verb and capture mux with VAIO STAC9872.
Also, changed the item names to be more intuitive.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The STAC codec support code has the automatic recognition of
additional side-output pins, and this may result in an error when
the assigned pin has no corresponding DAC connection.
The patch fixes the problem -- it corrects the line_outs again
without such additional pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added support for EAPD on the 927x, and 9227-8 IDT HDA codecs.
Enabling EAPD powers the internal speaker amp otherwise there is no
sound on systems with an internal amp.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added a new model 'dell' for Dell XPS M1210 with STAC922x codec chip.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
STAC922x provides the capture boost level up to 4, but actually it
works only up to 2. Since the range of the mixer is automatically
defined from amp-capability bits, we need to override the value
beforehand. snd_hda_override_amp_caps() is introduced for this
purpose.
The function patch_stac922x() calls this for NID 0x12 (Mux Capture
Volume). This should fix another recording problem on Intel Macs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
* adds the pinconfigs for all 5 Apple boards and 14 Subsystem IDs
(support for possibly all iMac, Mac, MacMini etc etc)
* adds 'intel-mac-v1' to v5 models which replace the current
* reflects changes in Alsa-Configuration.txt
Signed-off-by: Ivan N. Zlatev <contact@i-nz.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the pin configs for newer version of Intel iMac.
The information provided by Ivan N. Zlatev <contact@i-nz.net>.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
STAC922x provides the capture boost level up to 4, but actually it
works only up to 2. Since the range of the mixer is automatically
defined from amp-capability bits, we need to override the value
beforehand. snd_hda_override_amp_caps() is introduced for this
purpose.
The function patch_stac922x() calls this for NID 0x12 (Mux Capture
Volume). This should fix another recording problem on Intel Macs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The recent fix for STAC92xx surround outputs broke the input pin
setting for shared line-in and mic jacks. This patch fixes the
breakage.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix pin default configs for speaker associations and sequence
for Gateway MX6453 machine with STAC925x codecs.
Signed-off-by: Steve Longerbeam <stevel@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds more Dell systems and a Panasonic laptop with
STAC9200 codecs.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for the Gateway NX860 system.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Included is a patch against current alsa-kernel hg tip adding
quirks that Ubuntu Dapper/Edgy/Feisty contains.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
* fixed surround playback on stac922x. Pin direction control bits were
not being set correctly in stac92xx_set_pinctl(). Specifically it
would refuse to set the port as an output if the port was already
configured as an input. Last hunk (#8).
* fixed an input mux bug on 92xx codecs. When there is more than one
possible input calculated for the muxes, the actual mux widget never
gets set from its reset default, which is index 0, in the stac9221
case that is port E. So alsamixer/amixer/gnome-mixer report the Mic
as being the selected input source, but in fact is something else
(line-in port E in stac9221 case). Another problem with this is that
if you actually try to set the mux input to 'Mic', nothing happens
because *cur_val == idx (see snd_hda_input_mux_put). You have to
actually toggle input source to line-in then back to mic to actually
set the mux widget. Hunk #7.
* fixed some typos in patch_sigmatel.c. Hunk #6.
* fix to stac92xx_add_dyn_out_pins() that fixes surround playback on
codecs with less that 4 DACs (stac9205 for example). It reads the widget
caps cache created by hda_codec to count the total number of analog DACs
found. It then uses that to determine whether there will be enough
independent DACs available for line/mic switch controls. Hunk #1, #2,
and #3.
* improvements to stac92xx_auto_fill_dac_nids() to make it more general.
This fixes surround playback on some codecs in combination with the
fix to stac92xx_add_dyn_out_pins() above. It reads the full connection
list now, instead of just the first entry, and then locates an analog
DAC in the list. If one is found and it's free, assign it to that line-out.
If no free DAC is found for the line-out, return -ENODEV. It also makes
sure to actually select the chosen DAC if more than one DAC is input to
the pin. Hunks #4, #5.
Signed-off-by: Steve Longerbeam <stevel@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added a missing call to resume mixer controls for STAC92xx codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add handling of Intel-iMac-specific pinconfig of the sound card.
Intel-iMac now handled as a separated subsystem.
Signed-off-by: Sylvain FORET <sylvain.foret@anu.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
First generation MacBooks were getting ignored by sigmatel drivers
and wrongly being identified as MACMINI. This patch makes them
identify as MACBOOK.
Signed-off-by: Abhijit Bhopatkar <bainonline@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix SPDIF output (at least on Realtek codecs). The DIGI_CONVERT verbs
have to be reset before the PCM stream is set up. Otherwise the digital
setup is screwed up.
Also, check the AMP capability before setting AMP of the digital out
widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Original idea from Nicolas Boichat <nicolas@boichat.ch>.
The pin configurations of Macmini and MacBook (1st generation, at least)
seem identical with MacBook Pro (1st generation).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Remove superfluous array member in stac9205_dmic_nids[]
- Use ARRAY_SIZE() instead of hard-coded numbers
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds the Sony Vaio VGC-LA1 to the stac9872_cfg_tbl.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix audio on Macbook Pro 1st generation.
Signed-off-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Initialize the first line-out widget as the output pin in stac92xx_init().
Some devices like MacPro seem to set this widget as INPUT as default,
and confuses the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Define pin configs for MacBook and MacBook Pro with STAC92xx codecs.
The latter is detected automatically by checking codec SSID now.
Also, fixed the documentation regarding available modeliof sigmatel
codec chips.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
When a device is unkown, the driver tries to set up the codec based on
the BIOS information. Then it may result in Oops if BIOS is broken.
The patch fixes the issue, falling back to a reference model in such a
case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Support port replicator headphone output on Dell Latitude D820 + D/Port.
Signed-off-by: Cory T. Tusar <ctusar@videon-central.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for Gateway laptops based on the
Sigmatel STAC9250 codecs, as well as basic support for
STAC9202/9250/9251 codecs. Some Gateway systems require
probe_mask=1 to work. More work to be done prior to alsa 1.0.14
final.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Adds support for handling EAPD on 9205 codecs
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Use snd_pci_quirk_lookup() for looking up a board config table.
The config table is sorted in numerical order of PCI SSIDs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch makes the needlessly global stac92xx_dmic_labels[] static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Adds support for digital microphone pin widgets on SigmaTel codecs.
Enables support only on the 9205 codecs for now.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixes Dell system detection on 9200 codecs. The support
to detect certain Dell machines was merged in the
9205 table where it will be unused on the various Dell
9200-based codec systems. This moves the subsystem IDs
to the correct 9200 table.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix/optimize the headphone auto-toggle function on sigmatel codecs.
The headphone pins are kept as output. When headhpones are unplugged,
you cannot hear anyway ;)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed mic input with STAC92xx codecs. The mic pin was sometimes set to
OUTPUT by the headphone jack detection.
Also, try to assign a secondary mic as front-mic (or vice versa)
in the auto-detection if possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Some machines have multiple headpohne pins (usually on the lpatop
and on the docking station) while the current hda-codec driver
assumes a single headphone pin. Now it supports multiple hp pins
(at least for detection).
The sigmatel 92xx code supports this new multiple hp pins.
It detects all hp pins for auto-muting, too.
Also, the driver checks speaker pins in addition. In some cases,
all line-out, speaker and hp-pins coexist.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Tobin Davis