If a VLAN tagged frame is received and the corresponding VLAN is not
configured on the soft interface, it will splat a WARN on every packet
received. This is a quite annoying behaviour for some scenarios, e.g. if
bat0 is bridged with eth0, and there are arbitrary VLAN tagged frames
from Ethernet coming in without having any VLAN configuration on bat0.
The code should probably create vlan objects on the fly and
transparently transport these VLAN-tagged Ethernet frames, but until
this is done, at least the WARN splat should be replaced by a rate
limited output.
Fixes: 354136bcc3 ("batman-adv: fix kernel crash due to missing NULL checks")
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a system which uses fixed PHY devices and calls
fixed_phy_register() then fixed_phy_unregister() we can exhaust the
number of fixed PHYs available after a while, since we keep incrementing
the variable phy_fixed_addr, but we never decrement it.
This patch fixes that by converting the fixed PHY allocation to using
IDA, which takes care of the allocation/dealloaction of the PHY
addresses for us.
Fixes: a759512174 ("net: phy: extend fixed driver with fixed_phy_register()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have 2 segments that are bolted for the kernel linear
mapping (ie 0xc000... addresses). This is 0 to 1TB and also the kernel
stacks. Anything accessed outside of these regions may need to be
faulted in. (In practice machines with TM always have 1T segments)
If a machine has < 2TB of memory we never fault on the kernel linear
mapping as these two segments cover all physical memory. If a machine
has > 2TB of memory, there may be structures outside of these two
segments that need to be faulted in. This faulting can occur when
running as a guest as the hypervisor may remove any SLB that's not
bolted.
When we treclaim and trecheckpoint we have a window where we need to
run with the userspace GPRs. This means that we no longer have a valid
stack pointer in r1. For this window we therefore clear MSR RI to
indicate that any exceptions taken at this point won't be able to be
handled. This means that we can't take segment misses in this RI=0
window.
In this RI=0 region, we currently access the thread_struct for the
process being context switched to or from. This thread_struct access
may cause a segment fault since it's not guaranteed to be covered by
the two bolted segment entries described above.
We've seen this with a crash when running as a guest with > 2TB of
memory on PowerVM:
Unrecoverable exception 4100 at c00000000004f138
Oops: Unrecoverable exception, sig: 6 [#1]
SMP NR_CPUS=2048 NUMA pSeries
CPU: 1280 PID: 7755 Comm: kworker/1280:1 Tainted: G X 4.4.13-46-default #1
task: c000189001df4210 ti: c000189001d5c000 task.ti: c000189001d5c000
NIP: c00000000004f138 LR: 0000000010003a24 CTR: 0000000010001b20
REGS: c000189001d5f730 TRAP: 4100 Tainted: G X (4.4.13-46-default)
MSR: 8000000100001031 <SF,ME,IR,DR,LE> CR: 24000048 XER: 00000000
CFAR: c00000000004ed18 SOFTE: 0
GPR00: ffffffffc58d7b60 c000189001d5f9b0 00000000100d7d00 000000003a738288
GPR04: 0000000000002781 0000000000000006 0000000000000000 c0000d1f4d889620
GPR08: 000000000000c350 00000000000008ab 00000000000008ab 00000000100d7af0
GPR12: 00000000100d7ae8 00003ffe787e67a0 0000000000000000 0000000000000211
GPR16: 0000000010001b20 0000000000000000 0000000000800000 00003ffe787df110
GPR20: 0000000000000001 00000000100d1e10 0000000000000000 00003ffe787df050
GPR24: 0000000000000003 0000000000010000 0000000000000000 00003fffe79e2e30
GPR28: 00003fffe79e2e68 00000000003d0f00 00003ffe787e67a0 00003ffe787de680
NIP [c00000000004f138] restore_gprs+0xd0/0x16c
LR [0000000010003a24] 0x10003a24
Call Trace:
[c000189001d5f9b0] [c000189001d5f9f0] 0xc000189001d5f9f0 (unreliable)
[c000189001d5fb90] [c00000000001583c] tm_recheckpoint+0x6c/0xa0
[c000189001d5fbd0] [c000000000015c40] __switch_to+0x2c0/0x350
[c000189001d5fc30] [c0000000007e647c] __schedule+0x32c/0x9c0
[c000189001d5fcb0] [c0000000007e6b58] schedule+0x48/0xc0
[c000189001d5fce0] [c0000000000deabc] worker_thread+0x22c/0x5b0
[c000189001d5fd80] [c0000000000e7000] kthread+0x110/0x130
[c000189001d5fe30] [c000000000009538] ret_from_kernel_thread+0x5c/0xa4
Instruction dump:
7cb103a6 7cc0e3a6 7ca222a6 78a58402 38c00800 7cc62838 08860000 7cc000a6
38a00006 78c60022 7cc62838 0b060000 <e8c701a0> 7ccff120 e8270078 e8a70098
---[ end trace 602126d0a1dedd54 ]---
This fixes this by copying the required data from the thread_struct to
the stack before we clear MSR RI. Then once we clear RI, we only access
the stack, guaranteeing there's no segment miss.
We also tighten the region over which we set RI=0 on the treclaim()
path. This may have a slight performance impact since we're adding an
mtmsr instruction.
Fixes: 090b9284d7 ("powerpc/tm: Clear MSR RI in non-recoverable TM code")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Olga Kornievskaia reports that the following test fails to trigger
an OPEN_DOWNGRADE on the wire, and only triggers the final CLOSE.
fd0 = open(foo, RDRW) -- should be open on the wire for "both"
fd1 = open(foo, RDONLY) -- should be open on the wire for "read"
close(fd0) -- should trigger an open_downgrade
read(fd1)
close(fd1)
The issue is that we're missing a check for whether or not the current
state transitioned from an O_RDWR state as opposed to having transitioned
from a combination of O_RDONLY and O_WRONLY.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes: cd9288ffae ("NFSv4: Fix another bug in the close/open_downgrade code")
Cc: stable@vger.kernel.org # 2.6.33+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The only users of audit_get_tty and audit_put_tty are internal to
audit, so move it out of include/linux/audit.h to kernel.h and create
a proper function rather than inlining it. This also reduces kABI
changes.
Suggested-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: line wrapped description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Move the calculations of values after the allocation in case the
allocation fails. This avoids wasting effort in the rare case that it
fails, but more importantly saves us extra logic to release the tty
ref.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Pull libata fixes from Tejun Heo:
"Two trivial fixes - one for a bug in the allocation failure path and
the other a compiler warning fix"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: sata_mv: fix mis-conversion in mv_write_cached_reg()
ata: fix return value check in ahci_seattle_get_port_info()
Pull HID fix from Jiri Kosina:
"Regression fix for multitouch palm rejection from Allen Hung"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: multitouch: enable palm rejection for Windows Precision Touchpad
Revert "HID: multitouch: enable palm rejection if device implements confidence usage"
If 'all' is selected, convert comm event to output CTF stream.
setup_non_sample_events() is called if non_sample is selected. It
creates a comm_class for comm event.
Use macros to generate and process_comm_event and add_comm_event. These
macros can be reused for other non-sample events.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1466767332-114472-6-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Following commits are going to allow 'perf data convert' to collect not
only samples, but also non-sample events like comm and fork. In this
patch we count non-sample events using c.non_sample_count, and prepare
to print number of both type of events like:
# ~/perf data convert --all --to-ctf ./out.ctf
[ perf data convert: Converted 'perf.data' into CTF data './out.ctf' ]
[ perf data convert: Converted and wrote 0.846 MB (6508 samples, 686 non-samples) ]
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1466767332-114472-5-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If 'all' option is selected, 'perf data convert' should convert not only
samples, but non-sample events such as comm and fork. Add this option in
perf_data_convert_opts. Following commits will add cmdline option to
select it.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1466767332-114472-4-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Following commits will add new option to 'perf data convert'. All options
should be grouped into a structure and passed to low level converter
(currently there's only one converter).
Introduce data-convert.h and define 'struct perf_data_convert_opts' in
it. Pass 'force' through opts.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1466767332-114472-3-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There are many value_set_##x helper for integer, but only for integer.
This patch adds value_set_string() helper to help following commits
create string fields.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1466767332-114472-2-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Marc reported use of uninitialized memory:
> In commit "403567217d3f perf symbols: Do not read symbols/data from
> device files" a check to uninitialzied memory was added. This leads to
> the following valgrind output:
>
> ==24515== Syscall param stat(file_name) points to uninitialised byte(s)
> ==24515== at 0x75B26D5: _xstat (in /lib/x86_64-linux-gnu/libc-2.22.so)
> ==24515== by 0x4E548D: stat (stat.h:454)
> ==24515== by 0x4E548D: is_regular_file (util.c:687)
> ==24515== by 0x4A5BEE: dso__load (symbol.c:1435)
> ==24515== by 0x4BB1AE: map__load (map.c:289)
> ==24515== by 0x4BB1AE: map__find_symbol (map.c:333)
> ==24515== by 0x4835B3: thread__find_addr_location (event.c:1300)
> ==24515== by 0x4B5342: add_callchain_ip (machine.c:1652)
> ==24515== by 0x4B5342: thread__resolve_callchain_sample (machine.c:1906)
> ==24515== by 0x4B9E7D: thread__resolve_callchain (machine.c:1958)
> ==24515== by 0x441B3E: process_event (builtin-script.c:795)
> ==24515== by 0x441B3E: process_sample_event (builtin-script.c:920)
> ==24515== by 0x4BEE29: perf_evlist__deliver_sample (session.c:1192)
> ==24515== by 0x4BEE29: machines__deliver_event (session.c:1229)
> ==24515== by 0x4BF770: perf_session__deliver_event (session.c:1286)
> ==24515== by 0x4BF770: ordered_events__deliver_event (session.c:114)
> ==24515== by 0x4C1D17: __ordered_events__flush (ordered-events.c:207)
> ==24515== by 0x4C1D17: ordered_events__flush.part.3 (ordered-events.c:274)
> ==24515== by 0x4BF44C: perf_session__process_user_event (session.c:1325)
> ==24515== by 0x4BF44C: perf_session__process_event (session.c:1451)
> ==24515== Address 0x807c6a0 is 0 bytes inside a block of size 4,096 alloc'd
> ==24515== at 0x4C29C0F: malloc (in /usr/lib/valgrind/vgpreload_memcheck-amd64-linux.so)
> ==24515== by 0x4A5BCB: dso__load (symbol.c:1421)
> ==24515== by 0x4BB1AE: map__load (map.c:289)
> ==24515== by 0x4BB1AE: map__find_symbol (map.c:333)
> ==24515== by 0x4835B3: thread__find_addr_location (event.c:1300)
> ==24515== by 0x4B5342: add_callchain_ip (machine.c:1652)
> ==24515== by 0x4B5342: thread__resolve_callchain_sample (machine.c:1906)
> ==24515== by 0x4B9E7D: thread__resolve_callchain (machine.c:1958)
> ==24515== by 0x441B3E: process_event (builtin-script.c:795)
> ==24515== by 0x441B3E: process_sample_event (builtin-script.c:920)
> ==24515== by 0x4BEE29: perf_evlist__deliver_sample (session.c:1192)
> ==24515== by 0x4BEE29: machines__deliver_event (session.c:1229)
> ==24515== by 0x4BF770: perf_session__deliver_event (session.c:1286)
> ==24515== by 0x4BF770: ordered_events__deliver_event (session.c:114)
> ==24515== by 0x4C1D17: __ordered_events__flush (ordered-events.c:207)
> ==24515== by 0x4C1D17: ordered_events__flush.part.3 (ordered-events.c:274)
> ==24515== by 0x4BF44C: perf_session__process_user_event (session.c:1325)
> ==24515== by 0x4BF44C: perf_session__process_event (session.c:1451)
> ==24515== by 0x4C0EAC: __perf_session__process_events (session.c:1804)
> ==24515== by 0x4C0EAC: perf_session__process_events (session.c:1858)
The reason was a typo that passed global 'name' variable as the
is_regular_file argument instead dso->long_name.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 403567217d ("perf symbols: Do not read symbols/data from device files")
Link: http://lkml.kernel.org/r/1466772025-17471-2-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Following commits introduce new evlists to record. This patch adjusts
record__pick_pc() and introduces perf_evlist__pick_pc() to read control
page from one specific evlist. record__pick_pc() will be improved to
search control page from multiple evlists.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1467023052-146749-4-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Following commits introduce new evlists to record. This patch adjusts
record__mmap_read_all() and record__mmap_read(): converting original
record__mmap_read_all() to record__mmap_read_evlist(), read from one
evlist; makes record__mmap_read() reading from specific evlist.
record__mmap_read_all() will be improved to read from multiple evlists.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1467023052-146749-3-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Following commits introduce multiple evlists to record. This patch
extracts perf_evlist__mmap_ex() processing to a new function, creates
record__mmap() and record__mmap_evlist() to wrap perf_evlist__mmap_ex()
and its error processing. They will be improvemented to create mmap for
all evlists.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1467023052-146749-2-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Otherwise some compiler might scream:
$ make LIBBABELTRACE_DIR=/opt/libbabeltrace/ LIBBABELTRACE=1
BUILD: Doing 'make -j4' parallel build
CC util/data-convert-bt.o
util/data-convert-bt.c: In function ‘convert__config’:
util/data-convert-bt.c:1299:19: error: implicit declaration of function ‘perf_config_u64’ [-Werror=implicit-function-declaration]
c->queue_size = perf_config_u64(var, value);
...
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 41840d211c ("perf config: Move config declarations from util/cache.h to util/config.h")
Link: http://lkml.kernel.org/r/1466772025-17471-1-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
'make build-test' doesn't test LIBBABELTRACE=1. It misses a building
failure caused by commit 41840d211c ("perf config: Move config
declarations from util/cache.h to util/config.h"), breaks bisect.
Add LIBBABELTRACE=1 to build-test.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1466818918-131281-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Diag intends to broadcast tcp_sk and udp_sk socket destruction.
Testing sk->sk_protocol for IPPROTO_TCP/IPPROTO_UDP alone is not
sufficient for this. Raw sockets can have the same type.
Add a test for sk->sk_type.
Fixes: eb4cb00852 ("sock_diag: define destruction multicast groups")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Fixes: d1d81d4c3d ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage Confidence is mandary to Windows Precision Touchpad devices. If
it is examined in input_mapping on a WIndows Precision Touchpad, a new add
quirk MT_QUIRK_CONFIDENCE desgned for such devices will be applied to the
device. A touch with the confidence bit is not set is determined as
invalid.
Tested on Dell XPS13 9343
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 25a84db15b ("HID: multitouch: enable palm rejection
if device implements confidence usage")
The commit enables palm rejection for Win8 Precision Touchpad devices but
the quirk MT_QUIRK_VALID_IS_CONFIDENCE it is using is not working very
properly. This quirk is originally designed for some WIn7 touchscreens. Use
of this for a Win8 Precision Touchpad will cause unexpected pointer jumping
problem.
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When calling eeh_rmv_device() in eeh_reset_device() for partial hotplug
case, @rmv_data instead of its address is the proper argument.
Otherwise, the stack frame is corrupted when writing to
@rmv_data (actually its address) in eeh_rmv_device(). It results in
kernel crash as observed.
This fixes the issue by passing @rmv_data, not its address to
eeh_rmv_device() in eeh_reset_device().
Fixes: 67086e32b5 ("powerpc/eeh: powerpc/eeh: Support error recovery for VF PE")
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Commit 311c7c71c9 ("net/mlx5e: Allocate DMA coherent memory on
reader NUMA node") introduced mlx5_*_alloc_node() but missed changing
some calling and warn messages. This patch introduces 2 changes:
* Use mlx5_buf_alloc_node() instead of mlx5_buf_alloc() in
mlx5_wq_ll_create()
* Update the failure warn messages with _node postfix for
mlx5_*_alloc function names
Fixes: 311c7c71c9 ("net/mlx5e: Allocate DMA coherent memory on reader NUMA node")
Signed-off-by: Wang Sheng-Hui <shhuiw@foxmail.com>
Acked-By: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: bgmac: Random fixes
This patch series fixes a few issues spotted by code inspection and
actual testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bgmac_open() calls phy_start() to initialize the PHY state machine,
which will set the interface's carrier state accordingly, no need to
force that as this could be conflicting with the PHY state determined by
PHYLIB.
Fixes: dd4544f054 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not start the transmit queue in bgmac_open(). If the
queue was stopped prior to closing then re-opening the interface, we
would never be able to wake-up again.
Fixes: dd4544f054 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are checking for the Start of Frame bit in the ctl1 word, while this
bit is set in the ctl0 word instead. Read the ctl0 word and update the
check to verify that.
Fixes: 9cde94506e ("bgmac: implement scatter/gather support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 7bb11dc9f5 ("bonding: unify all places where
actor-oper key needs to be updated."), the logic in bonding to handle
selection between multiple aggregators has not functioned.
This affects only configurations wherein the bonding slaves
connect to two discrete aggregators (e.g., two independent switches, each
with LACP enabled), thus creating two separate aggregation groups within a
single bond.
The cause is a change in 7bb11dc9f5 to no longer set
AD_PORT_BEGIN on a port after a link state change, which would cause the
port to be reselected for attachment to an aggregator as if were newly
added to the bond. We cannot restore the prior behavior, as it
contradicts IEEE 802.1AX 5.4.12, which requires ports that "become
inoperable" (lose carrier, setting port_enabled=false as per 802.1AX
5.4.7) to remain selected (i.e., assigned to the aggregator). As the port
now remains selected, the aggregator selection logic is not invoked.
A side effect of this change is that aggregators in bonding will
now contain ports that are link down. The aggregator selection logic
does not currently handle this situation correctly, causing incorrect
aggregator selection.
This patch makes two changes to repair the aggregator selection
logic in bonding to function as documented and within the confines of the
standard:
First, the aggregator selection and related logic now utilizes the
number of active ports per aggregator, not the number of selected ports
(as some selected ports may be down). The ad_select "bandwidth" and
"count" options only consider ports that are link up.
Second, on any carrier state change of any slave, the aggregator
selection logic is explicitly called to insure the correct aggregator is
active.
Reported-by: Veli-Matti Lintu <veli-matti.lintu@opinsys.fi>
Fixes: 7bb11dc9f5 ("bonding: unify all places where actor-oper key needs to be updated.")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes wrong-interface signaling on 32-bit platforms for entries
created when jiffies > 2^31 + MFC_ASSERT_THRESH.
Signed-off-by: Tom Goff <thomas.goff@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test_fp_ctl function is used to test if a given value is a valid
floating-point control. The inline assembly in test_fp_ctl uses an
incorrect constraint for the 'orig_fpc' variable. If the compiler
chooses the same register for 'fpc' and 'orig_fpc' the test_fp_ctl()
function always returns true. This allows user space to trigger
kernel oopses with invalid floating-point control values on the
signal stack.
This problem has been introduced with git commit 4725c86055
"s390: fix save and restore of the floating-point-control register"
Cc: stable@vger.kernel.org # v3.13+
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This reverts commit 852ffd0f4e.
There are use cases where an intermediate boot kernel (1) uses kexec
to boot the final production kernel (2). For this scenario we should
provide the original boot information to the production kernel (2).
Therefore clearing the boot information during kexec() should not
be done.
Cc: stable@vger.kernel.org # v3.17+
Reported-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core()
gets called following message gets printed in debug console:
----------------->8---------------
CONFIG_ARC_DW2_UNWIND needs to be enabled
----------------->8---------------
That message makes sense if user indeed wants to see a backtrace or
get nice function call-graphs in perf but what if user disabled
unwinder for the purpose? Why pollute his debug console?
So instead we'll warn user about possibly missing feature once and
let him decide if that was what he or she really wanted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With recent binutils update to support dwarf CFI pseudo-ops in gas, we
now get .eh_frame vs. .debug_frame. Although the call frame info is
exactly the same in both, the CIE differs, which the current kernel
unwinder can't cope with.
This broke both the kernel unwinder as well as loadable modules (latter
because of a new unhandled relo R_ARC_32_PCREL from .rela.eh_frame in
the module loader)
The ideal solution would be to switch unwinder to .eh_frame.
For now however we can make do by just ensureing .debug_frame is
generated by removing -fasynchronous-unwind-tables
.eh_frame generated with -gdwarf-2 -fasynchronous-unwind-tables
.debug_frame generated with -gdwarf-2
Fixes STAR 9001058196
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull input fixes from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: vmmouse - remove port reservation
Input: elantech - add more IC body types to the list
Input: wacom_w8001 - ignore invalid pen data packets
Input: wacom_w8001 - w8001_MAX_LENGTH should be 13
Input: xpad - fix oops when attaching an unknown Xbox One gamepad
MAINTAINERS: add Pali Rohár as reviewer of ALPS PS/2 touchpad driver
Input: add HDMI CEC specific keycodes
Input: add BUS_CEC type
Input: xpad - fix rumble on Xbox One controllers with 2015 firmware
CPU notifications from the firmware coming in when cpufreq is
suspended cause cpufreq_update_current_freq() to return 0 which
triggers the WARN_ON() in cpufreq_update_policy() for no reason.
Avoid that by checking cpufreq_suspended before calling
cpufreq_update_current_freq().
Fixes: c9d9c929e6 (cpufreq: Abort cpufreq_update_current_freq() for cpufreq_suspended set)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
If of_match_node() fails, this init function bails out without
calling of_node_put().
Also change of_node_put(of_root) to of_node_put(np); both of them
hold the same pointer, but it seems better to call of_node_put()
against the node returned by of_find_node_by_path().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
intel_pstate_set_policy() is invoked by the cpufreq core during
driver initialization, on changes of policy attributes (minimim and
maximum frequency, for example) via sysfs and via CPU notifications
from the platform firmware. On some platforms the latter may occur
relatively often.
Commit bb6ab52f2b (intel_pstate: Do not set utilization update hook
too early) made intel_pstate_set_policy() clear the CPU's utilization
update hook before updating the policy attributes for it (and set the
hook again after doind that), but that involves invoking
synchronize_sched() and adds overhead to the CPU notifications
mentioned above and to the sched-RCU handling in general.
That extra overhead is arguably not necessary, because updating
policy attributes when the CPU's utilization update hook is active
should not lead to any adverse effects, so drop the clearing of
the hook from intel_pstate_set_policy() and make it check if
the hook has been set already when attempting to set it.
Fixes: bb6ab52f2b (intel_pstate: Do not set utilization update hook too early)
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull kbuild regression fix from Michal Marek:
"The problem is that commit 9c8fa9bc08 ("kbuild: fix if_change and
friends to consider argument order") fixed a potential missed rebuild,
but this results in unnnecessary rebuilds with the packaging targets.
Which is still more correct than the previous logic, but also very
annoying"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Initialize exported variables
This isn't functionally apparent for some reason, but
when we test io at extreme offsets at the end of the loff_t
rang, such as in fstests xfs/071, the calculation of
"max" in dax_io() can be wrong due to pos + size overflowing.
For example,
# xfs_io -c "pwrite 9223372036854771712 512" /mnt/test/file
enters dax_io with:
start 0x7ffffffffffff000
end 0x7ffffffffffff200
and the rounded up "size" variable is 0x1000. This yields:
pos + size 0x8000000000000000 (overflows loff_t)
end 0x7ffffffffffff200
Due to the overflow, the min() function picks the wrong
value for the "max" variable, and when we send (max - pos)
into i.e. copy_from_iter_pmem() it is also the wrong value.
This somehow(tm) gets magically absorbed without incident,
probably because iter->count is correct. But it seems best
to fix it up properly by comparing the two values as
unsigned.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull cifs fixes from Steve French:
"Various small cifs/smb3 fixes, include some for stable, and some from
the recent SMB3 test event"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
File names with trailing period or space need special case conversion
Fix reconnect to not defer smb3 session reconnect long after socket reconnect
cifs: check hash calculating succeeded
cifs: dynamic allocation of ntlmssp blob
cifs: use CIFS_MAX_DOMAINNAME_LEN when converting the domain name
cifs: stuff the fl_owner into "pid" field in the lock request
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Missing length check for user-space GETALG request
- Bogus memmove length in ux500 driver
- Incorrect priority setting for vmx driver
- Incorrect ABI selection for vmx driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: user - re-add size check for CRYPTO_MSG_GETALG
crypto: ux500 - memmove the right size
crypto: vmx - Increase priority of aes-cbc cipher
crypto: vmx - Fix ABI detection
Add few more triplets based on Fedora and Ubuntu binutils (cross tools).
Before applying patch on x86:
( Install binutils-powerpc64-linux-gnu.x86_64 )
$ perf report -i perf.data.powerpc --vmlinux vmlinux.powerpc \
--objdump powerpc64-linux-gnu-objdump
After applying patch on x86:
$ perf report -i perf.data.powerpc --vmlinux vmlinux.powerpc
I.e. it will find the right objdump from the environment data recorded
in the perf.data file + these triplets.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Link: http://lkml.kernel.org/r/1466769240-12376-7-git-send-email-ravi.bangoria@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Introduce helper to detect 'ret' instructions and use the same in the TUI.
A helper is needed since some architectures such as powerpc have more
than one return instruction.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Link: http://lkml.kernel.org/r/1466769240-12376-5-git-send-email-ravi.bangoria@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Simon Wunderlich