Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).
Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).
This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.
Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.
Also disable link (reset SIA) before sleep (de4x5 does this too).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).
de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets. This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subject workaround was causing CRC errors due to writing the wrong
register with updates of the RCTL register. It was also found that the
workaround function which modifies the RCTL register was being called in
the middle of a read-modify-write operation of the RCTL register, so the
function call has been moved appropriately. Lastly, jumbo frames must not
be allowed when CRC stripping is disabled by a module parameter because the
workaround requires the CRC be stripped.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82579, there is a hardware bug that can cause received packets to not
get transferred from the PHY to the MAC due to K1 (a power saving feature
of the PHY-MAC interconnect similar to ASPM L1). Since the MAC controls
the accounting of missed packets, these will go unnoticed. Workaround the
issue by setting the K1 beacon duration according to the link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two recent patches to cleanup the reset[1] and initial PHY configuration[2]
code paths for ICH/PCH devices inadvertently left out a 10msec delay and
device ID check respectively which are necessary for the 82566DC (device id
0x104b) to be configured properly, otherwise it will not get link.
[1] commit e98cac447c
[2] commit 3f0c16e844
CC: stable@kernel.org
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware is prevented from performing automatic PHY configuration
(the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL
register will not get cleared preventing the SMBus address and the LED
configuration to be written to the PHY registers. On 82579, do not check
the OEM_WRITE_ENABLE bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan)
in addition to the MAC before configuring PHY wakeup otherwise the PHY
configuration writes might be missed. Also write the LED configuration
and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and
e1000_write_smbus_addr, respectively). The reset is no longer needed
since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and
leaving it in causes issues with auto-negotiating the link.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are allocated in atl1_setup_ring_resources, zero out the pointers
in atl1_free_ring_resources (like the other resources).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).
Cc: stable@kernel.org
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is set in core network.
Dont change it unless dealing with fragments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is set in core network.
Dont change it unless dealing with fragments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic driver allocates rx skbs and gives to hardware too bytes of extra
storage, allowing for corruption of kernel data.
NET_IP_ALIGN being 0 on some platforms (including x86), drivers should
not assume it's 2.
rds_ring->skb_size = rds_ring->dma_size + NET_IP_ALIGN;
...
skb = dev_alloc_skb(rds_ring->skb_size);
skb_reserve(skb, 2);
pci_map_single(pdev, skb->data, rds_ring->dma_size, PCI_DMA_FROMDEVICE);
(and rds_ring->skb_size == rds_ring->dma_size) -> bug
Because of extra alignment (1500 + 32) -> four extra bytes are available
before the struct skb_shared_info, so corruption is not noticed.
Note: this driver could use netdev_alloc_skb_ip_align()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Direct Cache Access is not supported on IOAT ver.3.0 multiple-IOH platforms.
This patch blocks registering of dca providers when multiple IOH detected with IOAT ver.3.0.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed formatting (tabs and line breaks).
The CHELSIO_GET_QSET_NUM device ioctl allows unprivileged users to read
4 bytes of uninitialized stack memory, because the "addr" member of the
ch_reg struct declared on the stack in cxgb_extension_ioctl() is not
altered or zeroed before being copied back to the user. This patch
takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed formatting (tabs and line breaks).
The EQL_GETMASTRCFG device ioctl allows unprivileged users to read 16
bytes of uninitialized stack memory, because the "master_name" member of
the master_config_t struct declared on the stack in eql_g_master_cfg()
is not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed formatting (tabs and line breaks).
The TIOCGICOUNT device ioctl allows unprivileged users to read
uninitialized stack memory, because the "reserved" member of the
serial_icounter_struct struct declared on the stack in hso_get_count()
is not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Thinkpad X100e seems to have some odd behaviour when the display is
powered off - the onboard r8169 starts generating rxfifo overflow errors.
The root cause of this has not yet been identified and may well be a
hardware design bug on the platform, but r8169 should be more resiliant to
this. This patch enables the rxfifo interrupt on 8168 devices and removes
the MAC version check in the interrupt handler, and the machine no longer
crashes when under network load while the screen turns off.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On resume, before starting the PAL state machine, check if the
adjust_link() method is well supplied. If not, this would lead to a
NULL pointer dereference in the phy_state_machine() function.
This scenario can happen if the Ethernet driver call manually the PHY
functions instead of using the PAL state machine. The mv643xx_eth driver
is a such example.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently brought to my attention that 802.3ad mode bonds would no
longer form when using some network hardware after a driver update.
After snooping around I realized that the particular hardware was using
page-based skbs and found that skb->data did not contain a valid LACPDU
as it was not stored there. That explained the inability to form an
802.3ad-based bond. For balance-alb mode bonds this was also an issue
as ARPs would not be properly processed.
This patch fixes the issue in my tests and should be applied to 2.6.36
and as far back as anyone cares to add it to stable.
Thanks to Alexander Duyck <alexander.h.duyck@intel.com> and Jesse
Brandeburg <jesse.brandeburg@intel.com> for the suggestions on this one.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: stable@kerne.org
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mergeable buffer case, we use headcount, log_num
and seg as indexes in same-size arrays, and
we know that headcount <= seg and
log_num equals either 0 or seg.
Therefore, the right thing to do is range-check seg,
not headcount as we do now: these will be different
if guest chains s/g descriptors (this does not
happen now, but we can not trust the guest).
Long term, we should add BUG_ON checks to verify
two other indexes are what we think they should be.
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Smatch complains because we check whether "pch->chan" is NULL and then
dereference it unconditionally on the next line. Partly the reason this
bug was introduced is because code was too complicated. I've simplified
it a little.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'wwan' devtype is meant for devices that require preconfiguration
and *every* time setup before the ethernet interface can be used, like
cellular modems which require a series of setup commands on serial ports
or other mechanisms before the ethernet interface will handle packets.
As ipheth only requires one-per-hotplug pairing setup with no
preconfiguration (like APN, phone #, etc) and the network interface is
usable at any time after that initial setup, remove the incorrect
devtype wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_alloc_skb_ip_align() helper and do correct allocation
Tested-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
niu_get_ethtool_tcam_all() assumes that its output buffer is the right
size, and warns before returning if it is not. However, the output
buffer size is under user control and ETHTOOL_GRXCLSRLALL is an
unprivileged ethtool command. Therefore this is at least a local
denial-of-service vulnerability.
Change it to check before writing each entry and to return an error if
the buffer is already full.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
* 'for-linus' of git://neil.brown.name/md:
md: resolve confusion of MD_CHANGE_CLEAN
md: don't clear MD_CHANGE_CLEAN in md_update_sb() for external arrays
Move .gitignore from drivers/md to lib/raid6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
pkt_sched: Fix lockdep warning on est_tree_lock in gen_estimator
ipvs: avoid oops for passive FTP
Revert "sky2: don't do GRO on second port"
gro: fix different skb headrooms
bridge: Clear INET control block of SKBs passed into ip_fragment().
3c59x: Remove incorrect locking; correct documented lock hierarchy
sky2: don't do GRO on second port
ipv4: minor fix about RPF in help of Kconfig
xfrm_user: avoid a warning with some compiler
net/sched/sch_hfsc.c: initialize parent's cl_cfmin properly in init_vf()
pxa168_eth: fix a mdiobus leak
net sched: fix kernel leak in act_police
vhost: stop worker only if created
MAINTAINERS: Add ehea driver as Supported
ath9k_hw: fix parsing of HT40 5 GHz CTLs
ath9k_hw: Fix EEPROM uncompress block reading on AR9003
wireless: register wiphy rfkill w/o holding cfg80211_mutex
netlink: Make NETLINK_USERSOCK work again.
irda: Correctly clean up self->ias_obj on irda_bind() failure.
wireless extensions: fix kernel heap content leak
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: wlan-ng: Explicitly set some fields in cfg80211 interface
Staging: octeon: depends on NETDEVICES
Staging: spectra: depend on X86_MRST
Staging: zram: free device memory when init fails
Staging: rt2870sta: Add more device IDs from vendor drivers
staging: comedi das08_cs.c: Fix io_req_t conversion
staging: spectra needs <linux/slab.h>
staging: hv: Fixed lockup problem with bounce_buffer scatter list
staging: hv: Increased storvsc ringbuffer and max_io_requests
staging: hv: Fixed the value of the 64bit-hole inside ring buffer
staging: hv: Fixed bounce kmap problem by using correct index
staging: hv: Fix missing functions for net_device_ops
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ftdi_sio: Added custom PIDs for ChamSys products
USB: cdc-acm: Fixing crash when ACM probing interfaces with no endpoint descriptors.
USB: cdc-acm: Add pseudo modem without AT command capabilities
USB: cxacru: Use a bulk/int URB to access the command endpoint
usb: serial: mos7840: Add USB IDs to support more B&B USB/RS485 converters.
USB: cdc-acm: Adding second ACM channel support for various Nokia and one Samsung phones
usb: serial: mos7840: Add USB ID to support the B&B Electronics USOPTL4-2P.
USB: ssu100: turn off debug flag
usb: allow drivers to use allocated bandwidth until unbound
USB: cp210x usb driver: add USB_DEVICE for Pirelli DP-L10 mobile.
USB: cp210x: Add B&G H3000 link cable ID
USB: CP210x Add new device ID
USB: option: fix incorrect novatel entries
USB: Fix kernel oops with g_ether and Windows
USB: rndis: section mismatch fix
USB: ehci-ppc-of: problems in unwind
USB: s3c-hsotg: Remove DEBUG define
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix tty_line must not be equal to number of allocated tty pointers in tty driver
serial: bfin_sport_uart: restore transmit frame sync fix
serial: fix port type conflict between NS16550A & U6_16550A
MAINTAINERS: orphan isicom
vt: Fix console corruption on driver hand-over.
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not oops when erroneous PEB is scheduled for scrubbing
UBI: fix kconfig unmet dependency
UBI: fix forward compatibility
UBI: eliminate update of list_for_each_entry loop cursor
* 'drm-intel-fixes' of git://anongit.freedesktop.org/~ickle/drm-intel: (25 commits)
intel_agp,i915: Add more sandybridge graphics device ids
drm/i915: Enable MI_FLUSH on Sandybridge
agp/intel: Fix cache control for Sandybridge
agp/intel: use #ifdef idiom for intel-agp.h
agp/intel: fix physical address mask bits for sandybridge
drm/i915: Prevent double dpms on
drm/i915: Avoid use of uninitialised values when disabling panel-fitter
drm/i915: Avoid pageflipping freeze when we miss the flip prepare interrupt
drm/i915: Tightly scope intel_encoder to prevent invalid use
drm/i915: Allocate the PCI resource for the MCHBAR
drm/i915/dp: Really try 5 times before giving up.
drm/i915/sdvo: Restore guess of the DDC bus in absence of VBIOS
drm/i915/dp: Boost timeout for enabling transcoder to 100ms
drm/i915: Re-use set_base_atomic to share setting of the display registers
drm/i915: Fix offset page-flips on i965+
drm/i915: Include a generation number in the device info
i915: return -EFAULT if copy_to_user fails
i915: return -EFAULT if copy_to_user fails
agp/intel: Promote warning about failure to setup flush to error.
drm/i915: overlay on gen2 can't address above 1G
...
It causes all kinds of DMA API debugging assertions and
all straight-forward attempts to fix it have failed.
So turn off SG, and we'll tackle making this work
properly in net-next-2.6
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a simplified version of the original patch from James Courtier-Dutton.
>From: James Courtier-Dutton
>Subject: [PATCH] Fix b44 RX FIFO overflow recovery.
>Date: Wednesday, June 30, 2010 - 1:11 pm
>
>This patch improves the recovery after a RX FIFO overflow on the b44
>Ethernet NIC.
>Before it would do a complete chip reset, resulting is loss of link
>for a few seconds.
>This patch improves this to do recovery in about 20ms without loss of link.
>
>Signed off by: James@superbug.co.uk
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug introduced in commit
de84727214
"3c59x: Use fine-grained locks for MII and windowed register access".
vortex_interrupt() holds vp->window_lock over multiple register
accesses to reduce locking overhead. However it also needs to call
vortex_error() sometimes, and that uses the regular functions for
access to windowed registers, which will try to acquire window_lock
again.
Therefore, drop window_lock around the call to vortex_error() and set
the window afterward reacquiring the lock. Since vortex_error() may
call vortex_rx(), which *does* require its caller to hold window_lock,
lift that call up into vortex_interrupt(). This also removes the
potential for calling vortex_rx() on a later-generation NIC.
Reported-and-tested-by: Jens Schüßler <jgs@trash.net> [in Debian's 2.6.32]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time_before_eq()/time_after_eq() functions operate on unsigned
long and only work if the difference between the two compared values
is smaller than half the range of unsigned long (31 bits on i386).
Some of the variables (slave->jiffies, dev->trans_start, dev->last_rx)
used by bonding store a copy of jiffies and may not be updated for a
long time. With HZ=1000, time_before_eq()/time_after_eq() will start
giving bad results after ~25 days.
jiffies will never be before slave->jiffies, dev->trans_start,
dev->last_rx by more than possibly a couple ticks caused by preemption
of this code. This allows us to detect/prevent these overflows by
replacing time_before_eq()/time_after_eq() with time_in_range().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot use spinlock when kmalloc is invoked with
GFP_KERNEL flag because it can sleep.
So this patch reviews the usage of spinlock within the
stmmac_resume function avoing this bug.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New pci ids for GT2 and GT2+ on desktop and mobile sandybridge,
and graphics device ids for server sandybridge. Also rename original
ids string to reflect GT1 version.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
MI_FLUSH is being deprecated, but still available on Sandybridge.
Make sure it's enabled as userspace still uses MI_FLUSH.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Sandybridge GTT has new cache control bits in PTE, which controls
graphics page cache in LLC or LLC/MLC, so we need to extend the mask
function to respect the new bits.
And set cache control to always LLC only by default on Gen6.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Ondrej Zary