Allows overriding default methods serial_in/serial_out.
In such platform specific replacement it is possible to use
other regshift, biased register offset, any other manipulation
that is not covered with common default methods.
Overriding default methods may be useful for platforms which got
serial peripheral with registers represented in big endian.
In this situation and assuming that 32 bit operations / alignment
is required then it may be useful to swab words before/after
accessing the serial registers.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the differences between the original 8250 patch, the revised 8250 patch
and the independant clean up of the octeon driver (to use platform devices properly yay!)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old interface just copies bits over and calls the newer one.
In addition we can now pass more information.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull the MCA deletion branch from Paul Gortmaker:
"It was good that we could support MCA machines back in the day, but
realistically, nobody is using them anymore. They were mostly limited
to 386-sx 16MHz CPU and some 486 class machines and never more than
64MB of RAM. Even the enthusiast hobbyist community seems to have
dried up close to ten years ago, based on what you can find searching
various websites dedicated to the relatively short lived hardware.
So lets remove the support relating to CONFIG_MCA. There is no point
carrying this forward, wasting cycles doing routine maintenance on it;
wasting allyesconfig build time on validating it, wasting I/O on git
grep'ping over it, and so on."
Let's see if anybody screams. It generally has compiled, and James
Bottomley pointed out that there was a MCA extension from NCR that
allowed for up to 4GB of memory and PPro-class machines. So in *theory*
there may be users out there.
But even James (technically listed as a maintainer) doesn't actually
have a system, and while Alan Cox claims to have a machine in his cellar
that he offered to anybody who wants to take it off his hands, he didn't
argue for keeping MCA support either.
So we could bring it back. But somebody had better speak up and talk
about how they have actually been using said MCA hardware with modern
kernels for us to do that. And David already took the patch to delete
all the networking driver code (commit a5e371f61ad3: "drivers/net:
delete all code/drivers depending on CONFIG_MCA").
* 'delete-mca' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MCA: delete all remaining traces of microchannel bus support.
scsi: delete the MCA specific drivers and driver code
serial: delete the MCA specific 8250 support.
arm: remove ability to select CONFIG_MCA
The support for CONFIG_MCA is being removed, since the 20
year old hardware simply isn't capable of meeting today's
software demands on CPU and memory resources.
This commit removes the MCA specific 8250 UART code.
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Introduce yet another 8250 registration function.
This time it is serial8250_register_8250_port() and it
allows us to register 8250 hardware instances using struct
uart_8250_port. The new function makes it possible to
register 8250 hardware that makes use of 8250 specific
callbacks such as ->dl_read() and ->dl_write().
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "KT" serial port has another use case for a "received break" quirk,
so before adding another special case to the 8250 core take this
opportunity to push such quirks out of the core and into a uart_port op.
Stephen says:
"If the callback function is to no longer live in 8250.c itself,
arch/arm/mach-tegra/devices.c isn't logically a good place to put it,
and that file will be going away once we get rid of all the board files
and move solely to device tree."
...so since 8250_pci.c houses all the quirks for pci serial devices this
quirk is similarly housed in of_serial.c. Once the open firmware
conversion completes the infrastructure details
(include/linux/of_serial.h, and the export) can all be removed to make
this self contained to of_serial.c.
Cc: Nhan H Mai <nhan.h.mai@intel.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
[stephen: kill CONFIG_SERIAL_TEGRA in favor just using CONFIG_ARCH_TEGRA]
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sending a break on the SOC UARTs found in some MPC83xx/85xx/86xx
chips seems to cause a short lived IRQ storm (/proc/interrupts
typically shows somewhere between 300 and 1500 events). Unfortunately
this renders SysRQ over the serial console completely inoperable.
The suggested workaround in the errata is to read the Rx register,
wait one character period, and then read the Rx register again.
We achieve this by tracking the old LSR value, and on the subsequent
interrupt event after a break, we don't read LSR, instead we just
read the RBR again and return immediately.
The "fsl,ns16550" is used in the compatible field of the serial
device to mark UARTs known to have this issue.
Thanks to Scott Wood for providing the errata data which led to
a much cleaner fix.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For drivers that need to construct their own IRQ handler, the
three components are seen in the current handle_port -- i.e.
Rx, Tx and modem_status.
Make these exported symbols so that "almost" 8250 UARTs can
construct their own IRQ handler with these shared components,
while working around their own unique errata issues.
The function names are given a serial8250 prefix, since they
are now entering the global namespace.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 6b1a98d1c4.
It causes a build error that needs to be resolved differently.
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Synopsys DesignWare 8250 is an 8250 that has an extra interrupt that
gets raised when writing to the LCR when busy. To handle this we need
special serial_out, serial_in and handle_irq methods. Add a new
function serial8250_use_designware_io() that configures a uart_port with
these accessors.
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some ports (e.g. Synopsys DesignWare 8250) have special requirements for
handling the interrupts. Allow these platforms to specify their own
interrupt handler that will override the default.
serial8250_handle_irq() is provided so that platforms can extend the IRQ
handler rather than completely replacing it.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Not every platform that has generic legacy 8250 ports manages to have them
clocked the right way or without errata. Provide a generic interface to
allow platforms to override the default behaviour in a manner that dumps
the complexity in *their* code not the 8250 driver.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a hook for platforms to specify custom pm methods.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UART Features extract from STEricsson U6715 data-sheet (arm926 SoC for mobile phone):
* Fully compatible with industry standard 16C550 and 16C450 from various
manufacturers
* RX and TX 64 byte FIFO reduces CPU interrupts
* Full double buffering
* Modem control signals include CTS, RTS, (and DSR, DTR on UART1 only)
* Automatic baud rate selection
* Manual or automatic RTS/CTS smart hardware flow control
* Programmable serial characteristics:
– Baud rate generation (50 to 3.25M baud)
– 5, 6, 7 or 8-bit characters
– Even, odd or no-parity bit generation and detection
– 1, 1.5 or 2 stop bit generation
* Independent control of transmit, receive, line status, data set interrupts and FIFOs
* Full status-reporting capabilities
* Separate DMA signaling for RX and TX
* Timed interrupt to spread receive interrupt on known duration
* DMA time-out interrupt to allow detection of end of reception
* Carkit pulse coding and decoding compliant with USB carkit control interface [40]
In 16550A auto-configuration, if the fifo size is 64 then it's an U6 16550A port
Add set_termios hook & export serial8250_do_set_termios to change uart
clock following baudrate
Signed-off-by: Philippe Langlais <philippe.langlais@stericsson.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is currently no provision for passing IRQ trigger flags for
serial IRQs with triggering requirements (such as GPIO IRQs)
This patch adds irqflags to plat_serial8250_port that can be passed
from board file to reqest_irq() of 8250 driver
Changes are backward compatible with boards passing UPF_SHARE_IRQ flag
Tested on Zoom2 board that has IRQF_TRIGGER_RISING requirement for 8250 irq
[Moved new flag to end to fix bugs in the original with the old_serial array
-- Alan]
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add flag value UPF_FIXED_TYPE which specifies that the UART type is
known and should not be probed. For this case the UARTs properties
are just copied out of the uart_config entry.
This allows us to keep SOC specific 8250 probe code out of 8250.c. In
this case we know the serial hardware will not be changing as it is on
the same silicon as the CPU, and we can specify it with certainty in
the board/cpu setup code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
special cases in the probing code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to use Cavium OCTEON specific serial i/o drivers, we first
patch the 8250 driver to use replaceable I/O functions. Compatible
I/O functions are added for existing iotypeS.
An added benefit of this change is that it makes it easy to factor
some of the existing special cases out to board/SOC specific support
code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
iotype code and bug work-arounds.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch extends the sm501 mfd with 8250 uart support. We're currently
doing this in the board specific r2d-1 code already, but it would be nice to
do move things into the mfd since it's more chip specific than board specific.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the private_data field to be specified in platform_data for the
standard 8250/16550 UART. This field is used by DW APB type UARTs and
without this patch it's only possible to set this field when registering
the port by hand. If private_data is not set then the driver will
potentially oops with a NULL pointer dereference.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At present, various parts of the serial code use unsigned long to define
resource addresses. This is a problem, because some 32-bit platforms have
physical addresses larger than 32-bits, and have mmio serial uarts located
above the 4GB point.
This patch changes the type of mapbase in both struct uart_port and struct
plat_serial8250_port to resource_size_t, which can be configured to be 64
bits on such platforms. The mapbase in serial_struct can't safely be
changed, because that structure is user visible.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
early_serial_setup was removed from serial.h, but forgot to put in
serial_8250.h
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Beacuse SERIAL_PORT_DFNS is removed from include/asm-i386/serial.h and
include/asm-x86_64/serial.h. the serial8250_ports need to be probed late in
serial initializing stage. the console_init=>serial8250_console_init=>
register_console=>serial8250_console_setup will return -ENDEV, and console
ttyS0 can not be enabled at that time. need to wait till uart_add_one_port in
drivers/serial/serial_core.c to call register_console to get console ttyS0.
that is too late.
Make early_uart to use early_param, so uart console can be used earlier. Make
it to be bootconsole with CON_BOOT flag, so can use console handover feature.
and it will switch to corresponding normal serial console automatically.
new command line will be:
console=uart8250,io,0x3f8,9600n8
console=uart8250,mmio,0xff5e0000,115200n8
or
earlycon=uart8250,io,0x3f8,9600n8
earlycon=uart8250,mmio,0xff5e0000,115200n8
it will print in very early stage:
Early serial console at I/O port 0x3f8 (options '9600n8')
console [uart0] enabled
later for console it will print:
console handover: boot [uart0] -> real [ttyS0]
Signed-off-by: <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is on our "Envoy" boxes which we have, according to the documentation, an
"Exar ST16C554/554D Quad UART with 16-byte Fifo's". The box also has two
other "on-board" serial ports and a modem chip.
The two on-board serial UARTs were being detected along with the first two
Exar UARTs. The last two Exar UARTs were not showing up and neither was the
modem.
This patch was the only way I could the kernel to see beyond the standard four
serial ports and get all four of the Exar UARTs to show up.
[akpm@osdl.org: build fix]
Signed-off-by: Paul B Schroeder <pschroeder@uplogix.com>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lennert Buytenhek
Add a PLAT8250_DEV_PLATFORM2, and convert the two ixdp2x01 CPLD serial
ports to use platform serial devices with ids PLAT8250_DEV_PLATFORM[12].
(The on-chip xscale UART is PLAT8250_DEV_PLATFORM, id #0.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Same reasoning as commit 747c8a5594
but this time we're making uart_port flags a bitwise type - not
all of these flags correspond with the old ASYNC_ flags, so there
is the possibility for bugs if the wrong ASYNC_* constants are
used. Always use UPF_* constants for uart_port->flags.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.
Signed-off-by: Pantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add separate files for the different 8250 ISA-based serial boards.
Looking across all the various architectures, it seems reasonable that
we can key the availability of the configuration options for these
beasts to the bus-related symbols (iow, CONFIG_ISA). We also standardise
the base baud/uart clock rate for these boards - I'm sure that isn't
architecture specific, but is solely dependent on the crystal fitted
on the board (which should be the same no matter what type of machine
its fitted into.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Noam Camus