Cleanup net/sched code to current CodingStyle and practices.
Reduce inline abuse
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a mqprio queueing discipline that by default creates
a pfifo_fast qdisc per tx queue and provides the needed configuration
interface.
Using the mqprio qdisc the number of tcs currently in use along
with the range of queues alloted to each class can be configured. By
default skbs are mapped to traffic classes using the skb priority.
This mapping is configurable.
Configurable parameters,
struct tc_mqprio_qopt {
__u8 num_tc;
__u8 prio_tc_map[TC_BITMASK + 1];
__u8 hw;
__u16 count[TC_MAX_QUEUE];
__u16 offset[TC_MAX_QUEUE];
};
Here the count/offset pairing give the queue alignment and the
prio_tc_map gives the mapping from skb->priority to tc.
The hw bit determines if the hardware should configure the count
and offset values. If the hardware bit is set then the operation
will fail if the hardware does not implement the ndo_setup_tc
operation. This is to avoid undetermined states where the hardware
may or may not control the queue mapping. Also minimal bounds
checking is done on the count/offset to verify a queue does not
exceed num_tx_queues and that queue ranges do not overlap. Otherwise
it is left to user policy or hardware configuration to create
useful mappings.
It is expected that hardware QOS schemes can be implemented by
creating appropriate mappings of queues in ndo_tc_setup().
One expected use case is drivers will use the ndo_setup_tc to map
queue ranges onto 802.1Q traffic classes. This provides a generic
mechanism to map network traffic onto these traffic classes and
removes the need for lower layer drivers to know specifics about
traffic types.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
Fix dependencies of netfilter realm match: it depends on NET_CLS_ROUTE,
which itself depends on NET_SCHED; this dependency is missing from netfilter.
Since matching on realms is also useful without having NET_SCHED enabled and
the option really only controls whether the tclassid member is included in
route and dst entries, rename the config option to IP_ROUTE_CLASSID and move
it outside of traffic scheduling context to get rid of the NET_SCHED dependeny.
Reported-by: Vladis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
After recent changes, (percpu stats on vlan/tunnels...), we dont need
anymore per struct netdev_queue tx_bytes/tx_packets/tx_dropped counters.
Only remaining users are ixgbe, sch_teql, gianfar & macvlan :
1) ixgbe can be converted to use existing tx_ring counters.
2) macvlan incremented txq->tx_dropped, it can use the
dev->stats.tx_dropped counter.
3) sch_teql : almost revert ab35cd4b8f (Use net_device internal stats)
Now we have ndo_get_stats64(), use it, even for "unsigned long"
fields (No need to bring back a struct net_device_stats)
4) gianfar adds a stats structure per tx queue to hold
tx_bytes/tx_packets
This removes a lockdep warning (and possible lockup) in rndis gadget,
calling dev_get_stats() from hard IRQ context.
Ref: http://www.spinics.net/lists/netdev/msg149202.html
Reported-by: Neil Jones <neiljay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HTB takes into account skb is segmented in stats updates.
Generalize this to all schedulers.
They should use qdisc_bstats_update() helper instead of manipulating
bstats.bytes and bstats.packets
Add bstats_update() helper too for classes that use
gnet_stats_basic_packed fields.
Note : Right now, TCQ_F_CAN_BYPASS shortcurt can be taken only if no
stab is setup on qdisc.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 57dbb2d83d (sched: add head drop fifo queue)
introduced pfifo_head_drop, and broke the invariant that
sch->bstats.bytes and sch->bstats.packets are COUNTER (increasing
counters only)
This can break estimators because est_timer() handles unsigned deltas
only. A decreasing counter can then give a huge unsigned delta.
My mid term suggestion would be to change things so that
sch->bstats.bytes and sch->bstats.packets are incremented in dequeue()
only, not at enqueue() time. We also could add drop_bytes/drop_packets
and provide estimations of drop rates.
It would be more sensible anyway for very low speeds, and big bursts.
Right now, if we drop packets, they still are accounted in byte/packets
abolute counters and rate estimators.
Before this mid term change, this patch makes pfifo_head_drop behavior
similar to other qdiscs in case of drops :
Dont decrement sch->bstats.bytes and sch->bstats.packets
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide child qdisc backlog (byte count) information so that "tc -s
qdisc" can report it to user.
packet count is already correctly provided.
qdisc red 11: parent 1:11 limit 60Kb min 15Kb max 45Kb ecn
Sent 3116427684 bytes 1415782 pkt (dropped 8, overlimits 7866 requeues 0)
rate 242385Kbit 13630pps backlog 13560b 8p requeues 0
marked 7865 early 1 pdrop 7 other 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slot_dequeue_head() should make sure slot skb chain is correct in both
ways, or we can crash if all possible flows are in use.
Jarek pointed out slot_queue_init() can now be done in sfq_init() once,
instead each time a flow is setup.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFQ is currently 'limited' to small packets, because it uses a 15bit
allotment number per flow. Introduce a scale by 8, so that we can handle
full size TSO/GRO packets.
Use appropriate handling to make sure allot is positive before a new
packet is dequeued, so that fairness is respected.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfq_walk() runs without qdisc lock. By the time it selects a non empty
hash slot and sfq_dump_class_stats() is run (with lock held), slot might
have been freed : We then access q->slots[SFQ_EMPTY_SLOT], out of
bounds, and crash in slot_queue_walk()
On previous kernels, bug is here but out of bounds qs[SFQ_DEPTH] and
allot[SFQ_DEPTH] are located in struct sfq_sched_data, so no illegal
memory access happens, only possibly wrong data reported to user.
Also, slot_dequeue_tail() should make sure slot skb chain is correctly
terminated, or sfq_dump_class_stats() can access freed skbs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Here is a respin of patch.
I'll send a short patch to make SFQ more fair in presence of large
packets as well.
Thanks
[PATCH v3 net-next-2.6] net_sched: sch_sfq: better struct layouts
This patch shrinks sizeof(struct sfq_sched_data)
from 0x14f8 (or more if spinlocks are bigger) to 0x1180 bytes, and
reduce text size as well.
text data bss dec hex filename
4821 152 0 4973 136d old/net/sched/sch_sfq.o
4627 136 0 4763 129b new/net/sched/sch_sfq.o
All data for a slot/flow is now grouped in a compact and cache friendly
structure, instead of being spreaded in many different points.
struct sfq_slot {
struct sk_buff *skblist_next;
struct sk_buff *skblist_prev;
sfq_index qlen; /* number of skbs in skblist */
sfq_index next; /* next slot in sfq chain */
struct sfq_head dep; /* anchor in dep[] chains */
unsigned short hash; /* hash value (index in ht[]) */
short allot; /* credit for this slot */
};
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jarek Poplawski <jarkao2@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deploying SFQ/IFB here at work, I found the allot management was
pretty wrong in sfq, even changing allot from short to int...
We should init allot for each new flow, not using a previous value found
in slot.
Before patch, I saw bursts of several packets per flow, apparently
denying the default "quantum 1514" limit I had on my SFQ class.
class sfq 11:1 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 7p requeues 0
allot 11546
class sfq 11:46 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 1p requeues 0
allot -23873
class sfq 11:78 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 5p requeues 0
allot 11393
After patch, better fairness among each flow, allot limit being
respected, allot is positive :
class sfq 11:e parent 11:
(dropped 0, overlimits 0 requeues 86)
backlog 0b 3p requeues 86
allot 596
class sfq 11:94 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 3p requeues 0
allot 1468
class sfq 11:a4 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 4p requeues 0
allot 650
class sfq 11:bb parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 3p requeues 0
allot 596
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently return for each active SFQ slot the number of packets in
queue. We can also give number of bytes accounted for these packets.
tc -s class show dev ifb0
Before patch :
class sfq 11:3d9 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 3p requeues 0
allot 1266
After patch :
class sfq 11:3e4 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 4380b 3p requeues 0
allot 1212
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dev_close_many and dev_deactivate_many to factorize another
sync-rcu operation on the netdevice unregister path.
$ modprobe dummy numdummies=10000
$ ip link set dev dummy* up
$ time rmmod dummy
Without the patch With the patch
real 0m 24.63s real 0m 5.15s
user 0m 0.00s user 0m 0.00s
sys 0m 6.05s sys 0m 5.14s
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate qdisc memory according to NUMA properties of cpus included in
xps map.
To be effective, qdisc should be (re)setup after changes
of /sys/class/net/eth<n>/queues/tx-<n>/xps_cpus
I added a numa_node field in struct netdev_queue, containing NUMA node
if all cpus included in xps_cpus share same node, else -1.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing struct netdev_queue state against FROZEN bit, we also test
XOFF bit. We can test both bits at once and save some cycles.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the documentation refers to web pages under
the domain `osdl.org'. However, `osdl.org' now
redirects to `linuxfoundation.org'.
Rather than rely on redirections, this patch updates
the addresses appropriately; for the most part, only
documentation that is meant to be current has been
updated.
The patch should be pretty quick to scan and check;
each new web-page url was gotten by trying out the
original URL in a browser and then simply copying the
the redirected URL (formatting as necessary).
There is some conflict as to which one of these domain
names is preferred:
linuxfoundation.org
linux-foundation.org
So, I wrote:
info@linuxfoundation.org
and got this reply:
Message-ID: <4CE17EE6.9040807@linuxfoundation.org>
Date: Mon, 15 Nov 2010 10:41:42 -0800
From: David Ames <david@linuxfoundation.org>
...
linuxfoundation.org is preferred. The canonical name for our web site is
www.linuxfoundation.org. Our list site is actually
lists.linux-foundation.org.
Regarding email linuxfoundation.org is preferred there are a few people
who choose to use linux-foundation.org for their own reasons.
Consequently, I used `linuxfoundation.org' for web pages and
`lists.linux-foundation.org' for mailing-list web pages and email addresses;
the only personal email address I updated from `@osdl.org' was that of
Andrew Morton, who prefers `linux-foundation.org' according `git log'.
Signed-off-by: Michael Witten <mfwitten@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The basic classifier keeps statistics but does not report it to user space.
This showed up when using basic classifier (with police) as a default catch
all on ingress; no statistics were reported.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somewhere along the lines net_cls_subsys_id became a macro when
cls_cgroup is built as a module. Not only did it make cls_cgroup
completely useless, it also causes it to crash on module unload.
This patch fixes this by removing that macro.
Thanks to Eric Dumazet for diagnosing this problem.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While validating the configuration em_ops is already set, thus the
individual destroy functions are called, but the ematch data has
not been allocated and associated with the ematch yet.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
The first parameter dev isn't in use in qdisc_create_dflt().
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Zijlstra found a bug in the way softirq time is accounted in
VIRT_CPU_ACCOUNTING on this thread:
http://lkml.indiana.edu/hypermail//linux/kernel/1009.2/01366.html
The problem is, softirq processing uses local_bh_disable internally. There
is no way, later in the flow, to differentiate between whether softirq is
being processed or is it just that bh has been disabled. So, a hardirq when bh
is disabled results in time being wrongly accounted as softirq.
Looking at the code a bit more, the problem exists in !VIRT_CPU_ACCOUNTING
as well. As account_system_time() in normal tick based accouting also uses
softirq_count, which will be set even when not in softirq with bh disabled.
Peter also suggested solution of using 2*SOFTIRQ_OFFSET as irq count
for local_bh_{disable,enable} and using just SOFTIRQ_OFFSET while softirq
processing. The patch below does that and adds API in_serving_softirq() which
returns whether we are currently processing softirq or not.
Also changes one of the usages of softirq_count in net/sched/cls_cgroup.c
to in_serving_softirq.
Looks like many usages of in_softirq really want in_serving_softirq. Those
changes can be made individually on a case by case basis.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-2-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a seqlock in struct neighbour to protect neigh->ha[], and avoid
dirtying neighbour in stress situation (many different flows / dsts)
Dirtying takes place because of read_lock(&n->lock) and n->used writes.
Switching to a seqlock, and writing n->used only on jiffies changes
permits less dirtying.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_headroom() is unsigned so "skb_headroom(skb) + toff" is also
unsigned and can't be less than zero. This test was added in 66d50d25:
"u32: negative offset fix" It was supposed to fix a regression.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ingress being not used very much, and net_device->ingress_queue being
quite a big object (128 or 256 bytes), use a dynamic allocation if
needed (tc qdisc add dev eth0 ingress ...)
dev_ingress_queue(dev) helper should be used only with RTNL taken.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is some confusion with rx_queue name after RPS, and net drivers
private rx_queue fields.
I suggest to rename "struct net_device"->rx_queue to ingress_queue.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list_head conversion unearther an unnecessary flow
check. Since flow is always NULL here we don't need to
see if a matching flow exists already.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes init_vf() function, so on each new backlog period parent's
cl_cfmin is properly updated (including further propgation towards the root),
even if the activated leaf has no upperlimit curve defined.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reviewing commit 1c40be12f7, I
audited other users of tc_action_ops->dump for information leaks.
That commit covered almost all of them but act_police still had a leak.
opt.limit and opt.capab aren't zeroed out before the structure is
passed out.
This patch uses the C99 initializers to zero everything unused out.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial extension to existing meta data match rules to allow
matching on skb receive hash value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for the declararion of csum_ipv6_magic.
Fixes this build error on PowerPC (at least):
net/sched/act_csum.c: In function 'tcf_csum_ipv6_icmp':
net/sched/act_csum.c:178: error: implicit declaration of function 'csum_ipv6_magic'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use rxhash to classify the traffic into flows. As rxhash maybe
supplied by NIC or RPS, it is cheaper.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller