NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TPC support has been observed to cause some tx power fluctuations on
some devices with at least AR934x and AR938x chips.
Disable it for now until the bugs have been found and fixed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sc->nbcnvifs tracks assigned beacon slots, not enabled beacons.
Therefore, it cannot be used to decide if cur_conf->enable_beacon (bool)
should be updated, or if beacons have been enabled already.
With the current code (depending on the order of calls), beacons often
do not get enabled in an AP+STA setup.
To fix tracking of enabled beacons, convert cur_conf->enable_beacon to a
bitmask of enabled beacon slots.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
atomic_inc(&tx_urbs);
if (atomic_read(&tx_urbs) >= 16) {
-->
atomic_dec(&tx_urbs);
netif_wake_queue();
return;
<--
netif_stop_queue();
}
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable the xilinx driver for ARM64.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This reverts commit 2b995f6398.
Панов Андрей reported the following regression:
"Commit 2b995f6398 in 4.0.0-rc3 introduces a
nasty bug in transmit, corrupting packets.
To reproduce:
$ dd if=/dev/zero of=zeros bs=1M count=20
$ md5sum -b zeros
8f4e33f3dc3e414ff94e5fb6905cba8c *zeros
This checksum is correct.
Copy file "zeros" to another host with NFS, and it gets corrupted, checksum is
changed.
File should be big, small amounts of transmit isn't affected.
I use an i.MX6 Quad board.
If this commit is reverted, all works fine."
Reported-by: Панов Андрей <rockford@yandex.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit dfd8645ea1 wrongly assumes that VXLAN_VDI_MASK includes
eight lower order reserved bits of VNI field that are using for remote
checksum offload.
Right now, when VNI number greater then 0xffff, vxlan_udp_encap_recv()
will always return with 'bad_flag' error, reducing the usable vni range
from 0..16777215 to 0..65535. Also, it doesn't really check whether RCO
bits processed or not.
Fix it by adding new VNI mask which has all 32 bits of VNI field:
24 bits for id and 8 bits for other usage.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array index 'j' is used before limits check.
Suggest put limit check before index use.
Signed-off-by : <Ameenali023@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't delete napi from hash list during module exit. This will
cause the following panic when doing module load and unload:
BUG: unable to handle kernel paging request at 0000004e00000075
IP: [<ffffffff816bd01b>] napi_hash_add+0x6b/0xf0
PGD 3c5d5067 PUD 0
Oops: 0000 [#1] SMP
...
Call Trace:
[<ffffffffa0a5bfb7>] init_vqs+0x107/0x490 [virtio_net]
[<ffffffffa0a5c9f2>] virtnet_probe+0x562/0x791815639d880be [virtio_net]
[<ffffffff8139e667>] virtio_dev_probe+0x137/0x200
[<ffffffff814c7f2a>] driver_probe_device+0x7a/0x250
[<ffffffff814c81d3>] __driver_attach+0x93/0xa0
[<ffffffff814c8140>] ? __device_attach+0x40/0x40
[<ffffffff814c6053>] bus_for_each_dev+0x63/0xa0
[<ffffffff814c7a79>] driver_attach+0x19/0x20
[<ffffffff814c76f0>] bus_add_driver+0x170/0x220
[<ffffffffa0a60000>] ? 0xffffffffa0a60000
[<ffffffff814c894f>] driver_register+0x5f/0xf0
[<ffffffff8139e41b>] register_virtio_driver+0x1b/0x30
[<ffffffffa0a60010>] virtio_net_driver_init+0x10/0x12 [virtio_net]
This patch fixes this by doing this in virtnet_free_queues(). And also
don't delete napi in virtnet_freeze() since it will call
virtnet_free_queues() which has already did this.
Fixes 91815639d8 ("virtio-net: rx busy polling support")
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this situation ever happens, the mac80211 state machine gets
confused because it never clears csa_active. There was a separate
bug that lead to this happening with a working connection, but it
isn't very robust to try to keep the connection up in this case.
When removing the time event the CSA essentially procedure stops,
so the safest thing to do is to disconnect in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
mac80211 now informs the driver when to drop the packets
upon flush(). This will happen before disconnecting, or
before we shut down the interface. We can now rely on this
to drop all the packets including the VO queues.
When mac80211 sets drop to false, wait for all the queues
to be empty.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This fixes a performance regression introduced by
7fbb9d8415 (xen-netback: release pending
index before pushing Tx responses)
Moving the notify outside of the spin locks means it can be delayed a
long time (if the dealloc thread is descheduled or there is an
interrupt or softirq).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix ROC removal - avoids a firmware crash
* fix throughput regression on iwldvm devices
* fix panic in BT Coex
* fixes in rate control
* fixes in scan
b43:
* fix support for 5 GHz only BCM43228 model
rtlwifi:
* improve handling of IPv6 packets
brcmfmac:
* perform bound checking on vendor command buffer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU/vcnAAoJEG4XJFUm622bBbMIAJAmmITit1LFbm5L5zguIkVq
b9ppfEkgz6JYb4KMe6jWnvrc9yM3ywslH2Evo09ChA53A2sUhORKxlolreGTZxtQ
je3twmUCyzkbvss+aKFS4BzEDDOGwW9A/wk3LT4TZJ7Jp626k1wPXN5WZHaDh0YC
pE7fH6jnNg2Qoe68tG8WmTqrYlzU6mLpI0NNxsW+h2tK2Gqm7jSoMy96RPiwS0ZV
BFnxrJJZViMyPit48pZf338pdndkxOIlDBIJCY8qUwQIt4HxQ8DnmsLWqg9xjnfT
mSO9xgSJxfR02ZDIBYqaK41KlcharjwrF5lDi+JHkoHB2SQQM9A/noxpWu4/JGI=
=pOSK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
iwlwifi:
* fix ROC removal - avoids a firmware crash
* fix throughput regression on iwldvm devices
* fix panic in BT Coex
* fixes in rate control
* fixes in scan
b43:
* fix support for 5 GHz only BCM43228 model
rtlwifi:
* improve handling of IPv6 packets
brcmfmac:
* perform bound checking on vendor command buffer
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver support receive VLAN CTAG HW acceleration feature
(NETIF_F_HW_VLAN_CTAG_RX) through software simulation. There calls the
api .skb_copy_to_linear_data_offset() to skip the VLAN tag, but there
have overlap between the two memory data point range. The patch just fix
the issue.
V2:
Michael Grzeschik suggest to use memmove() instead of skb_copy_to_linear_data_offset().
Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Fixes: 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurations are not modified by the driver. Make them 'const' so
that they may be placed in a read-only section.
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes a missing initialization of ctrlmode and ctrlmode_supported fields,
for all other CAN devices than the first one. This fix only concerns
the PCAN-USB Pro FD dual-channels CAN-FD device made by PEAK-System.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com>
Reported-by: Daniel Steer <daniel.steer@mclaren.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A short or malformed vendor command buffer could cause reads outside
the command buffer.
Cc: stable@vger.kernel.org # v3.19
Signed-off-by: Pontus Fuchs <pontusf@broadcom.com>
[arend@broadcom.com: slightly modified debug trace output]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver is removed (e.g. using unbind through sysfs), the
clocks get disabled twice, once on fec_enet_close and once on
fec_drv_remove. Since the clocks are enabled only once, this leads
to a warning:
WARNING: CPU: 0 PID: 402 at drivers/clk/clk.c:992 clk_core_disable+0x64/0x68()
Remove the call to fec_enet_clk_enable in fec_drv_remove to balance
the clock enable/disable calls again. This has been introduce by
e8fcfcd568 ("net: fec: optimize the clock management to save power").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest spec "I-IPA01-0266-USR Rev 10" limit the MID field length to 12 bit
value. For previous versions it is 16 bit value.
This change will not break the backward compatibility as the latest ID value is
7 and with in the 12 bit value limit.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC of-nodes may have children which are not queue-group nodes. For
example new-style fixed-phy declarations. These where incorrectly
assumed to be additional queue-groups.
Change the search to filter out any nodes which are not queue-groups,
or have been disabled.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_set_wol() correctly sets MPD_PW_EN when a password is specified
to match magic packets against, however, when we switch from a
password-matching to a matching without password we would leave this bit
turned on, and GENET would only match magic packets with passwords.
This can be reproduced using the following sequence:
ethtool -s eth0 wol g
ethtool -s eth0 wol s sopass 00:11:22:33:44:55
ethtool -s eth0 wol g
The simple fix is to clear the MPD_PWD_EN bit when WAKE_MAGICSECURE is
not set.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de7b5b3d79 ("net: eth: xgene: change APM X-Gene SoC platform
ethernet to support ACPI") breaks booting with devicetree with UEFI
firmware. In that case, I get:
Unhandled fault: synchronous external abort (0x96000010) at 0xfffffc0000620010
Internal error: : 96000010 [#1] SMP
Modules linked in: vfat fat xfs libcrc32c ahci_xgene libahci_platform libahci
CPU: 7 PID: 634 Comm: NetworkManager Not tainted 4.0.0-rc1+ #4
Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0-rh-0.14 Mar 1 2015
task: fffffe03d4c7e100 ti: fffffe03d4e24000 task.ti: fffffe03d4e24000
PC is at xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
LR is at xgene_gmac_tx_enable+0x2c/0x50
pc : [<fffffe000069d6fc>] lr : [<fffffe000069dcc4>] pstate: 80000145
sp : fffffe03d4e27590
x29: fffffe03d4e27590 x28: 0000000000000000
x27: fffffe03d4e277c0 x26: fffffe03da8fda10
x25: fffffe03d4e2760c x24: fffffe03d49e28c0
x23: fffffc0000620004 x22: 0000000000000000
x21: fffffc0000620000 x20: fffffc0000620010
x19: 000000000000000b x18: 000003ffd4a96020
x17: 000003ff7fc1f7a0 x16: fffffe000079b9cc
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: fffffe03d4e24000
x11: fffffe03d4e27da0 x10: 0000000000000001
x9 : 0000000000000000 x8 : fffffe03d4e27a20
x7 : 0000000000000000 x6 : 00000000ffffffef
x5 : fffffe000105f7d0 x4 : fffffe00007ca8c8
x3 : fffffe03d4e2760c x2 : 0000000000000000
x1 : fffffc0000620000 x0 : 0000000040000000
Process NetworkManager (pid: 634, stack limit = 0xfffffe03d4e24028)
Stack: (0xfffffe03d4e27590 to 0xfffffe03d4e28000)
...
Call trace:
[<fffffe000069d6fc>] xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
[<fffffe000069dcc0>] xgene_gmac_tx_enable+0x28/0x50
[<fffffe00006a112c>] xgene_enet_open+0x2c/0x130
[<fffffe00007b9254>] __dev_open+0xc8/0x148
[<fffffe00007b956c>] __dev_change_flags+0x90/0x158
[<fffffe00007b9664>] dev_change_flags+0x30/0x70
[<fffffe00007c8ab8>] do_setlink+0x278/0x870
[<fffffe00007c95bc>] rtnl_newlink+0x404/0x6a8
[<fffffe00007c8040>] rtnetlink_rcv_msg+0x98/0x218
[<fffffe00007e78e4>] netlink_rcv_skb+0xe0/0xf8
[<fffffe00007c7f94>] rtnetlink_rcv+0x30/0x44
[<fffffe00007e6f2c>] netlink_unicast+0xfc/0x210
[<fffffe00007e75b8>] netlink_sendmsg+0x498/0x5ac
[<fffffe00007990b8>] do_sock_sendmsg+0xa4/0xcc
[<fffffe000079a958>] ___sys_sendmsg+0x1fc/0x208
[<fffffe000079b984>] __sys_sendmsg+0x4c/0x94
[<fffffe000079b9f8>] SyS_sendmsg+0x2c/0x3c
The problem here is that the enet hw clocks are not getting
initialized because of a test to avoid the initialization if
UEFI is used to boot. This is an incorrect test. When booting
with UEFI and devicetree, the kernel must still initialize
the enet hw clocks. If booting with ACPI, the clock hw is
not exposed to the kernel and it is that case where we want
to avoid initializing clocks.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Feng Kan <fkan@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Cc: stable<stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling a from-guest frag list, xenvif_handle_frag_list()
replaces the frags before calling the destructor to clean up the
original (foreign) frags. Whilst this is safe (the destructor doesn't
actually use the frags), it looks odd.
Reorder the function to be less confusing.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time a VIF is destroyed up to 256 pages may be leaked if packets
with more than MAX_SKB_FRAGS frags were transmitted from the guest.
Even worse, if another user of ballooned pages allocated one of these
ballooned pages it would not handle the unexpectedly >1 page count
(e.g., gntdev would deadlock when unmapping a grant because the page
count would never reach 1).
When handling a from-guest skb with a frag list, unref the frags
before releasing them so they are freed correctly when the VIF is
destroyed.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct pointer arithmetic to get the pointer to each stat.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit below introduced an unsafe dereference of
mvmvif->phy_ctxt. It can be NULL even if we hold the mutex.
We can be handling a BT Coex notification while the vif has
already been unassigned. This can happen since the BT Coex
notification is hanled asynchronuously: we can have started
to handle the BT Coex notification trying to acquire the
mutex while the unassign flow already got it. The BT Coex
notification handling will wait for the mutext. I'll get it
later, but then mvmvif->phy_ctxt will be NULL.
Panic log:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<f985180d>] iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm]
*pdpt = 0000000000000000 *pde = f000eef300000007
Oops: 0000 [#1] SMP
Workqueue: events iwl_mvm_async_handlers_wk [iwlmvm]
task: ed719b20 ti: ec03e000 task.ti: ec03e000
EIP: 0060:[<f985180d>] EFLAGS: 00010202 CPU: 2
EIP is at iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm]
EAX: 00000000 EBX: f6d3cb70 ECX: f6d3cb70 EDX: 00000000
ESI: ec03fe40 EDI: efeb8810 EBP: ec03fdf0 ESP: ec03fdac
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000000 CR3: 01a1a000 CR4: 001407f0
Stack:
f743ca80 f744a404 ec03fdcc c10e3952 00003aba f743ca80 00000246 f743ca80
00000246 00000000 00000001 00000000 ebd45ff6 ebd458a4 f6d3c500 ebd45578
ebd44b01 ec03fe18 f99e1bc2 00000002 ebd44bc0 f9851770 00000000 f6d3c500
Call Trace:
[<c10e3952>] ? ring_buffer_unlock_commit+0xa2/0xd0
[<f99e1bc2>] __iterate_interfaces+0x82/0x110 [mac80211]
[<f9851770>] ? iwl_mvm_bt_coex_reduced_txp+0x140/0x140 [iwlmvm]
[<f99e1c6a>] ieee80211_iterate_active_interfaces_atomic+0x1a/0x20 [mac80211]
[<f9851427>] iwl_mvm_bt_coex_notif_handle+0x77/0x280 [iwlmvm]
[<f9852161>] iwl_mvm_rx_bt_coex_notif_old+0x211/0x220 [iwlmvm]
[<f9850b8b>] iwl_mvm_rx_bt_coex_notif+0x19b/0x1b0 [iwlmvm]
[<f983944f>] iwl_mvm_async_handlers_wk+0x7f/0xe0 [iwlmvm]
CC: <stable@vger.kernel.org> [3.19+]
Fixes: 123f515635 ("iwlwifi: mvm: BT Coex - add support for TTC / RRC")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I recently did a rework of the smc91x driver and did some build-testing
by compiling hundreds of randconfig kernels. Unfortunately, my script
was wrong and did not actually test the configurations that mattered,
so I introduced stupid typos in almost every file I touched.
I fixed my script now, built all configurations that actually matter
and fixed all the typos, this is the result.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b70661c708 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the backward compatibile of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.
Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're getting IRQs after lots of resources are already
allocated:
* netdev
* clocks
* MDIO bus
Also HW gets initialized by the time when checking IRQs as well.
Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.
But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.
For example this is what happens for me:
--->8---
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
platform e0018000.ethernet: Driver stmmaceth requests probe deferral
...
...
...
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
sysfs_warn_dup+0x4e/0x68
sysfs_create_dir_ns+0x98/0xa0
kobject_add_internal+0x8c/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W
4.0.0-rc1-next-20150303+ #8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
kobject_add_internal+0x218/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be2 ]---
libphy: mii_bus stmmac-0 failed to register
: Cannot register as MDIO bus
stmmac_pltfr_probe: main driver probe failed
stmmaceth: probe of e0018000.ethernet failed with error -22
--->8---
Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Commit 6ce29b0e2a ("gianfar: Avoid unnecessary reg accesses in adjust_link()")
eliminates unnecessary calls to adjust_link for phy devices which don't support
interrupts and need polling. As part of that work, the 'new_state' local flag,
which was used to reduce logging noise on the console, was eliminated.
Unfortunately, that means that a 'Link is Down' log message will now be
issued continuously if a link is configured as UP, the link state is down,
and the associated phy requires polling. This occurs because priv->oldduplex
is -1 in this case, which always differs from phydev->duplex. In addition,
phydev->speed may also differ from priv->oldspeed. gfar_update_link_state()
is therefore called each time a phy is polled, even if the link state did not
change.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function that will enable changing the MAC address
of an ibmveth interface while it is still running.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routine rtl_is_special_data() is supposed to identify packets that need to
use a low bit rate so that the probability of successful transmission is
high. The current version has a bug that causes all IPv6 packets to be
labelled as special, with a corresponding low rate of transmission. A
complete fix will be quite intrusive, but until that is available, all
IPv6 packets are identified as regular.
This patch also removes a magic number.
Reported-and-tested-by: Alan Fisher <acf@unixcube.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Cc: Alan Fisher <acf@unixcube.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was incorrectly detected as 2 GHz device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding. That isn't the case; we need to use skb_put_padto() instead.
(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2. We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)
Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fd9af07c34.
The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16. I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).
Also adjust a comment to agree with this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor. This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips. This will result in unpredictable behaviour on those chips
after an RDE.
Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips. This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.
Fixes: 79fba9f517 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.
Add memory barriers to ensure that this ordering is maintained.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets which are sent from the selftest (ethtool) flow,
should not be passed to GRO stack but rather dropped by
the driver after validation. To achieve that, we disable
GRO for the duration of the selftest.
Fixes: dd65beac48 ("net/mlx4_en: Extend usage of napi_gro_frags")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS)
of the update-qp command was defined twice (using enum value and pre-processor
define directive) and wrong.
The return value of the call to mlx4_update_qp() from within the SRIOV
resource-tracker was wrongly voided down.
Fix both issues.
issue: none
Fixes: 09e05c3f78 ('net/mlx4: Set vlan stripping policy by the right command')
Fixes: ce8d9e0d67 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 60b4ea1781 ("net: systemport: log RX buffer allocation and RX/TX DMA
failures") added a few software maintained statistics using
BCM_SYSPORT_STAT_MIB_RX and BCM_SYSPORT_STAT_MIB_TX. These statistics are read
from the hardware MIB counters, such that bcm_sysport_update_mib_counters() was
trying to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCM_SYSPORT_STAT_SOFT, similar to
BCM_SYSPORT_STAT_NETDEV, such that bcm_sysport_get_ethtool_stats will read from
the software mib.
Fixes: 60b4ea1781 ("net: systemport: log RX buffer allocation and RX/TX DMA failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 44c8bc3ce3 ("net: bcmgenet: log RX buffer allocation and RX/TX dma
failures") added a few software maintained statistics using
BCMGENET_STAT_MIB_RX and BCMGENET_STAT_MIB_TX. These statistics are read from
the hardware MIB counters, such that bcmgenet_update_mib_counters() was trying
to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCMGENET_STAT_SOFT, similar to
BCMGENET_STAT_NETDEV, such that bcmgenet_get_ethtool_stats will read from the
software mib.
Fixes: 44c8bc3ce3 ("net: bcmgenet: log RX buffer allocation and RX/TX dma failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'mutliple' to 'multiple'
Change 'Firmare' to 'Firmware'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
cpsw_suspend/resume calbacks under CONFIG_PM_SLEEP
to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a dev_pm_ops suspend_late/resume_early pair but not a
set of hibernation functions means those pm functions will
not be called upon hibernation.
Fix this by using SET_LATE_SYSTEM_SLEEP_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
davinci_mdio_x callbacks under CONFIG_PM_SLEEP to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 740c7f31c0 ("sh_eth: Ensure DMA engines are stopped before
freeing buffers") added a call to sh_eth_reset() to the
sh_eth_set_ringparam() and sh_eth_close() paths.
However, setting the software reset bit(s) in the EDMR register resets
the MAC Address Registers to zero. Hence after kexec, the new kernel
doesn't detect a valid MAC address and assigns a random MAC address,
breaking DHCP.
Set the MAC address again after the reset in sh_eth_dev_exit() to fix
this.
Tested on r8a7740/armadillo (GETHER) and r8a7791/koelsch (FAST_RCAR).
Fixes: 740c7f31c0 ("sh_eth: Ensure DMA engines are stopped before freeing buffers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the
interrupt load and send xmit in network stack on time. This also
separated for the completion of tx_ring16 from bcmgenet_poll.
The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt
is to be not more than a certain number TxBDs. It is caused by too
slowly reclaiming the transmitted skb. Therefore, performance
degradation of xmit after 605ad7f ("tcp: refine TSO autosizing").
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian reported crashes using IPv6 traffic with macvtap/veth combo.
I tracked the crashes in neigh_hh_output()
-> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD);
Neighbour code assumes headroom to push Ethernet header is
at least 16 bytes.
It appears macvtap has only 14 bytes available on arches
where NET_IP_ALIGN is 0 (like x86)
Effect is a corruption of 2 bytes right before skb->head,
and possible crashes if accessing non existing memory.
This fix should also increase IPv4 performance, as paranoid code
in ip_finish_output2() wont have to call skb_realloc_headroom()
Reported-by: Brian Rak <brak@vultr.com>
Tested-by: Brian Rak <brak@vultr.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
four-way-handshake problem. The others are various small fixes
for problems all over, nothing really stands out.
-----BEGIN PGP SIGNATURE-----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=H3+7
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few patches have accumulated, among them the fix for Linus's
four-way-handshake problem. The others are various small fixes
for problems all over, nothing really stands out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, sending a packet with the source MAC address of one
of the CPSW interfaces to one of the CPSW slave ports while it's configured in
dual_emac mode would update the port_num field of the VLAN/Unicast Address
Table Entry. This would cause it to discard all incoming traffic addressed to
that MAC address, essentially rendering the port useless until the ALE table is
cleared (by starting and stopping the interface or rebooting.)
For example, if eth0 has a MAC address of 90:59:af:8f:43:e9 it will have
an ALE table entry:
00 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=0 addr=90:59:af:8f:43:e9)
If you configure another device with the same MAC address and connect it
to the first CPSW slave port and send some traffic the ALE table entry
becomes:
04 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=1 addr=90:59:af:8f:43:e9)
>From this point forward all incoming traffic addressed to
90:59:af:8f:43:e9 will be dropped.
Setting the SECURE bit for the VLAN/Unicast address table entry for each
interface's MAC address corrects the problem.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a discrepancy here because the niu_class_to_ethflow() returns
zero on failure and one on success but the caller expected zero on
success and negative on failure.
The problem means that we allow the user to pass classes and flow_types
which we don't want. I've looked at it a bit and I don't see it as a
very serious bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver traditionally gets configured at compile-time
for whichever hardware it runs on. This no longer works on
ARM as we continue to move to building all-in-one kernels.
Most ARM configurations with this driver already use run-time
configuration through DT or through platform_data, but a
few have not been converted yet.
I've checked all ARM boards that use this driver in their
legacy board files, and converted the ones that were using
compile-time configuration in smc91x.h to behave like the
other ones and provide the interrupt polarity along with
the MMIO configuration (width, stride) at platform device
creation time.
In particular, these combinations were previously selectable
in Kconfig but in fact broken:
- sa1100 assabet plus pleb
- msm combined with any other armv6/v7 platform
- pxa-idp combined with any non-DMA pxa variant
- LogicPD PXA270 combined with any other pxa
- nomadik combined with any other armv4/v5 platform,
e.g. versatile.
None of these seem critical enough to warrant a backport
to stable, but it would be nice to clean this up for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
----
I would like the patch to get merged through netdev, after
Robert and/or Linus have verified it on at least some hardware.
There are a few other non-ARM platforms using this driver,
I could do the same patch for those if we want to take
it further.
arch/arm/mach-msm/board-halibut.c | 8 ++++-
arch/arm/mach-msm/board-qsd8x50.c | 8 ++++-
arch/arm/mach-pxa/idp.c | 5 +++
arch/arm/mach-pxa/lpd270.c | 8 ++++-
arch/arm/mach-realview/core.c | 7 ++++
arch/arm/mach-realview/realview_eb.c | 2 +-
arch/arm/mach-sa1100/neponset.c | 6 ++++
arch/arm/mach-sa1100/pleb.c | 7 ++++
drivers/net/ethernet/smsc/smc91x.c | 9 +++--
drivers/net/ethernet/smsc/smc91x.h | 114 ++----------------------------------------------------------
10 files changed, 57 insertions(+), 117 deletions(-)
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-26
This series contains fixes for i40e and i40evf only.
Alexey Khoroshilov found a possible leak of 'cmd_buf' when copy_from_user()
failed in i40e_dbg_command_write(), so resolved by calling kfree().
Shannon provides a fix to ensure the shift and bitwise precedences do not
work backwards for us by adding parans. Fixed the driver by preventing
the driver from allowing stray interrupts or causing system logs from
un-handled interrupts by combining the ICR0 shutdown with the standard
interrupt shutdown and add the interrupt clearing to the PCI shutdown
path. Fixed an issue where a NVM write times out before a transaction
can complete, so Shannon added logic to make another attempt by
reacquiring the semaphore, then retry the write, if the one retry fails,
we will then give up. Adds checks to pointers before their use to ensure
we do not try to dereference NULL pointers when returning values from the
AdminQ calls.
Akeem adds a check to bail out if the device is already down when checking
for Tx hang subtask.
Anjali fixes TSO with more than 8 frags per segment issue. The hardware
has some limitations which the driver needs to adhere to:
1) no more than 8 descriptors per packet on the wire
2) no header can span more than 3 descriptors
If one of these events happens, the hardware will generate an internal
error and freeze the Tx queue, so Anjali fixes this by linearizes the skb
to avoid these situations. Fixed an issue where the per Traffic Class
queue count was higher than queues enabled, which will fix a warning
with multiple function mode where systems regularly have more cores than
vectors. Fixed TCP/IPv6 over VXLAN Tx checksum offload, where we were
checking the outer protocol flags and deciding the flow for the inner
header.
Jesse fixes a race condition in the transmit hang detection. Before we
were having issues of false Tx hang detection, no the driver makes more
direct with the checks for progress forward by directly checking the head
write back address and tail register when determining progress. This
avoids Tx hangs where the software gets behind, because we are directly
checking hardware state when determining a hang state.
Neerav fixes the transmit ring Qset handle when DCB reconfigures. The issue
was when DCB is reconfigured to a single traffic class (TC) and the driver
did not reset the Tx ring Qset handle to correct the mapping, which caused
the Tx queue to disable timeouts. Also as part of DCB reconfiguration flow
if the Tx queue disable times out, then issue a PF reset to do some level
of recovery.
Mitch stops flow director on shutdown because, in some cases, the hardware
would continue to try to access the FDIR ring after entering D3Hot state,
which would cause either PCIe errors or NMIs, depending upon the system
configuration.
* NOTE * I have verified that this series of patches for net will not cause
any merge issues when you sync up your net tree with your net-next tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the hardware may not have been properly shutdown
before this driver gets control, through use by firmware, for example.
Until the driver is loaded, interrupts associated with the hardware
could go pending. When the IRQs are requested napi support has not
been initialized yet, but the ISR will get control and schedule napi
processing resulting in a kernel panic because the poll routine has not
been set.
Adjust the code so that the driver is fully ready to handle and process
interrupts as soon as the IRQs are requested. This involves requesting
and freeing IRQs during start and stop processing and ordering the napi
add and delete calls appropriately.
Also adjust the powerup and powerdown routines to match the start and
stop routines in regards to the ordering of tasks, including napi
related calls.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "Sitecom Europe B.V. LN-028 Network USB 2.0 Adapter".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
"val" is declared as a u64 so static checkers complain that this shift
can wrap. I don't have the hardware but probably it's doesn't have over
31 ports. Still we may as well silence the warning even if it's not a
real bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure kmalloc() succeeds.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reads and writes to adapter memory via the PCI-E Memory Window
interface, data gets swizzled on 4-byte boundaries on Big-Endian systems
because we need to account for the register read/write interface which
incorporates a swizzle onto the Little-Endian PCI-E Bus.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should complete notify_check before returning the credits. Once we return the
credits, adaptor may access the notify data.
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we don't try to dereference NULL pointers when returning values
from the AdminQ calls.
Change-ID: Ia6694f2f415d50acf0aba063c863568742799aff
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, a multi-write transaction takes longer than the
default 3 minute timeout on the write semaphore. If the write failed with
an EBUSY status, this is likely the problem, so here we try to reacquire
the semaphore then retry the write. We only do one retry, then give up.
Change-ID: I1c8be60688acc2f39573839579baf601207c4a36
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some cases, the hardware would continue to try to access the FDIR
ring after entering D3Hot state, which would cause either PCIe errors or
NMIs, depending upon system configuration.
Explicitly stop FDIR in our shutdown routine to eliminate this
possibility.
Change-ID: I1bd9fc7fd8f151fe24cad132ac9adddab923e3af
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Combine the ICR0 shutdown with the standard interrupt shutdown, and
add the interrupt clearing to the PCI shutdown path.
This prevents the driver from allowing stray interrupts or causing
system logs from un-handled interrupts.
Change-ID: I48f6ab95cad7f8ca77c1f26c92a51cc1034ced43
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were checking the outer Protocol flags and deciding the flow for
inner header. This patch fixes that.
This fixes the Tx checksum offload for TCP/IPv6 over vxlan.
Change-ID: I837aaea921d34f71b24c2bc32aaadea5001ddf78
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of DCB reconfiguration flow if the Tx queue disable times out
then issue a PF reset to do some level of recovery.
Change-ID: I7550021c55bff355351c0365e61e1f05fcaff46d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When DCB is reconfigured to single TC the driver did not reset the
Tx ring Qset handle to the correct mapping; which caused Tx queue
disable timeouts.
Change-ID: I4da5915ec92a83c281b478d653fae6ef1b72edfe
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver or hardware gets less interrupt vectors than the actual
number of CPU cores, limit the queue count for the priority queue
traffic class (TC) queues.
This will fix a warning with multiple function mode where systems
regularly have more cores than vectors.
Also add extra comment for readability.
Change-ID: I4f02226263aa3995e1f5ee5503eac0cd6ee12fbd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was having some issues with false Tx hang detection. This
makes the driver a little more direct with the checks for progress
forward by directly checking the head write back address and tail register
when determining progress. This avoids Tx hangs where the software
gets behind, because we are directly checking hardware state when
determining hang state.
Change-ID: I774f0e861c9e8ab5ccb213634100fe15440ae24a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware has some limitations the driver needs to adhere to,
that we found in extended testing.
1) no more than 8 descriptors per packet on the wire
2) no header can span more than 3 descriptors
If one of these events occurs, the hardware will generate an internal
error and freeze the Tx queue.
This patch linearizes the skb to avoid these situations.
Change-ID: I37dab7d3966e14895a9663ec4d0aaa8eb0d9e115
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds check to bail out if device is already down when checking
for Tx hang subtask.
Change-ID: I3853fb7a6d11cb9a4c349b687cb25c15b19977a0
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add parens to make sure the shift and bitwise precedences don't work backwards
for us.
Change-ID: I60c10ef4fad6bc654522b9d8a53da2e270a0f268
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes a leak of 'cmd_buf' when copy_from_user() failed
in i40e_dbg_command_write().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY requires different settings for the Decision Feedback Analyzer
(DFE) when running in KX mode vs. KR mode. Update the code to change
these settings when changing modes in order to provide a more stable
link.
Additionally, adjust the 10GbE PQ skew default setting to a more sane
value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit below didn't update the max_ht_ampdu_exponent
for the devices listed in iwl-[1-6]000.c which, in result,
became 0 instead of 8K. This reduced the size of the Rx
AMPDU from 64K to 8K which had an impact in the Rx
throughput. One user reported that because of this, his
downstream throughput droppped by a half.
CC: <stable@vger.kernel.org> [3.19]
Fixes: c064ddf318 ("iwlwifi: change max HT and VHT A-MPDU exponent")
Reported-and-tested-by: Valentin Manea <linux-wireless@mrs.ro>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the pending indexes are released /after/ pushing the Tx response
then a stale pending index may be used if a new Tx request is
immediately pushed by the frontend. The may cause various WARNINGs or
BUGs if the stale pending index is actually still in use.
Fix this by releasing the pending index before pushing the Tx
response.
The full barrier for the pending ring update is not required since the
the Tx response push already has a suitable write barrier.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct two problems with the error handling when using the netlink
forwarding API: first, the netlink skb is never freed if nla_put()
fails; and second, genlmsg_unicast() can fail if the netlink socket
is full. In the latter case, the corresponding data skb is not counted
as a drop and userspace programs like wmediumd will see TCP stalls
due to lost packets.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Incorrect NAPI polling caused WARNING at net/core/dev.c net_rx_action.
Some stability issues were also seen at high throughput and system
load before this patch.
This patch contains several changes in altera_tse_main.c:
- tse_rx() is fixed to not process more than `limit` frames
- tse_poll() is refactored to match NAPI logic
- only received frames are counted for return value
- removed bogus condition `(rxcomplete >= budget || txcomplete > 0)`
- replace by: if (rxcomplete < budget) -> call __napi_complete and enable irq
- altera_isr()
- replace spin_lock_irqsave() by spin_lock() - we are in isr
- use spinlocks just over irq manipulation, not over __napi_schedule
- reset IRQ first, then disable and schedule napi
This is a cleaned up resubmission from Vlastimil's recent submission.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Roman Pisl <rpisl@kky.zcu.cz>
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a typo in the way tx_fifo_depth is read from the
devicetree. This patch was submitted by Vlastimil about a week ago,
and is now cleaned up and resubmitted.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current FW is declaring support for BFER in ucode_capa.capa
but it doesn't really support it unless the new LQ_SS_PARAMS API
is supported as well. Avoid publishing BFER in our VHT caps
if FW doesn't support.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eran Ben Elisha