Probably due to copy&paste, some stuff was simply forgotten.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We hit an hang issue when removing a mmc device on Medfield Android phone by sysfs interface.
device_pm_remove will call pm_runtime_remove which would disable
runtime PM of the device. After that pm_runtime_get* or
pm_runtime_put* will be ignored. So if we disable the runtime PM
before device really be removed, drivers' _remove callback may
access HW even pm_runtime_get* fails. That is bad.
Consider below call sequence when removing a device:
device_del => device_pm_remove
=> class_intf->remove_dev(dev, class_intf) => pm_runtime_get_sync/put_sync
=> bus_remove_device => device_release_driver => pm_runtime_get_sync/put_sync
remove_dev might call pm_runtime_get_sync/put_sync.
Then, generic device_release_driver also calls pm_runtime_get_sync/put_sync.
Since device_del => device_pm_remove firstly, later _get_sync wouldn't really wake up the device.
I git log -p to find the patch which moves the calling to device_pm_remove ahead.
It's below patch:
commit 775b64d2b6
Author: Rafael J. Wysocki <rjw@sisk.pl>
Date: Sat Jan 12 20:40:46 2008 +0100
PM: Acquire device locks on suspend
This patch reorganizes the way suspend and resume notifications are
sent to drivers. The major changes are that now the PM core acquires
every device semaphore before calling the methods, and calls to
device_add() during suspends will fail, while calls to device_del()
during suspends will block.
It also provides a way to safely remove a suspended device with the
help of the PM core, by using the device_pm_schedule_removal() callback
introduced specifically for this purpose, and updates two drivers (msr
and cpuid) that need to use it.
As device_pm_schedule_removal is deleted by another patch, we need also revert other parts of the patch,
i.e. move the calling of device_pm_remove after the calling to bus_remove_device.
Signed-off-by: LongX Zhang <longx.zhang@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When PM runtime is enabled in DaVinci and the machine migrates to
common clk framework, the clk_enable() gets called without
clk_prepare(). This patch is to fix this issue so that PM run
time can inter work with common clk framework.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the opp_find* functions return -ENODEV when:
a) it cant find a device (e.g. request for an OPP search on device
which was not registered)
b) When it cant find a match for the search strategy used
This makes life a little in-efficient for users such as devfreq
to make reasonable judgement before switching search strategies.
So, standardize the return results as following:
-EINVAL for bad pointer parameters
-ENODEV when device cannot be found
-ERANGE when search fails
This has the following benefit for devfreq implementation:
The search fails when an unregistered device pointer is provided.
This is a trigger to change the search direction and search for
a better fit, however, if we cannot differentiate between a valid
search range failure Vs an unregistered device, second search goes
through the same fail return condition. This can be avoided by
appropriate handling of error return code.
With this change, we also fix devfreq for the improved search
strategy with updated error code.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export the OPP functions for use by driver modules.
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@ti.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
[nm@ti.com: expansion of functions exported]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
synchronize_rcu() blocks the caller of opp_enable/disbale
for a complete grace period. This blocking duration prevents
any intensive use of the functions. Replace synchronize_rcu()
by call_rcu() which will call our function for freeing the old
opp element.
The duration of opp_enable() and opp_disable() will be no more
dependant of the grace period.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With ACPI 5 it is now possible to enumerate traditional SoC
peripherals, like serial bus controllers and slave devices behind
them. These devices are typically based on IP-blocks used in many
existing SoC platforms and platform drivers for them may already
be present in the kernel tree.
To make driver "porting" more straightforward, add ACPI support to
the platform bus type. Instead of writing ACPI "glue" drivers for
the existing platform drivers, register the platform bus type with
ACPI to create platform device objects for the drivers and bind the
corresponding ACPI handles to those platform devices.
This should allow us to reuse the existing platform drivers for the
devices in question with the minimum amount of modifications.
This changeset is based on Mika Westerberg's and Mathias Nyman's
work.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch documents the firmware cache mechanism so that
users of request_firmware() know that it can be called
safely inside device's suspend and resume callback, and
the device's firmware needn't be cached any more by individual
driver itself to deal with firmware loss during system resume.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces one module parameter of 'path' in firmware_class
to support customizing firmware image search path, so that people can
use its own firmware path if the default built-in paths can't meet their
demand[1], and the typical usage is passing the below from kernel command
parameter when 'firmware_class' is built in kernel:
firmware_class.path=$CUSTOMIZED_PATH
[1], https://lkml.org/lkml/2012/10/11/337
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment above fw_file_size() suggests it is noinline for stack size
reasons. Use noinline_for_stack to make this more clear.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is one race that both request_firmware() with the same
firmware name.
The race scenerio is as below:
CPU1 CPU2
request_firmware() -->
_request_firmware_load() return err another request_firmware() is coming -->
_request_firmware_cleanup is called --> _request_firmware_prepare -->
release_firmware ---> fw_lookup_and_allocate_buf -->
spin_lock(&fwc->lock)
... __fw_lookup_buf() return true
fw_free_buf() will be called --> ...
kref_put -->
decrease the refcount to 0
kref_get(&tmp->ref) ==> it will trigger warning
due to refcount == 0
__fw_free_buf() -->
... spin_unlock(&fwc->lock)
spin_lock(&fwc->lock)
list_del(&buf->list)
spin_unlock(&fwc->lock)
kfree(buf)
After that, the freed buf will be used.
The key race is decreasing refcount to 0 and list_del is not protected together by
fwc->lock, and it is possible another thread try to get it between refcount==0
and list_del.
Fix it here to protect it together.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race as below when calling request_firmware():
CPU1 CPU2
write 0 > loading
mutex_lock(&fw_lock)
...
set_bit FW_STATUS_DONE class_timeout is coming
set_bit FW_STATUS_ABORT
complete_all &completion
...
mutex_unlock(&fw_lock)
In this time, the bit FW_STATUS_DONE and FW_STATUS_ABORT are set,
and request_firmware() will return failure due to condition in
_request_firmware_load():
if (!buf->size || test_bit(FW_STATUS_ABORT, &buf->status))
retval = -ENOENT;
But from the above scenerio, it should be a successful requesting.
So we need judge if the bit FW_STATUS_DONE is already set before
calling fw_load_abort() in timeout function.
As Ming's proposal, we need change the timer into sched_work to
benefit from using &fw_lock mutex also.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Ming Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since dev_pm_qos_add_request(), dev_pm_qos_update_request() and
dev_pm_qos_remove_request() for PM QoS flags should not be invoked
when device in RPM_SUSPENDED, add pm_runtime_get_sync() and pm_runtime_put()
around these functions in dev_pm_qos_expose_flags() and
dev_pm_qos_hide_flags().
[rjw: Modified the subject and changelog to better reflect the code
changes made.]
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull sparc fixes from David Miller:
"Several build/bug fixes for sparc, including:
1) Configuring a mix of static vs. modular sparc64 crypto modules
didn't work, remove an ill-conceived attempt to only have to build
the device match table for these drivers once to fix the problem.
Reported by Meelis Roos.
2) Make the montgomery multiple/square and mpmul instructions actually
usable in 32-bit tasks. Essentially this involves providing 32-bit
userspace with a way to use a 64-bit stack when it needs to.
3) Our sparc64 atomic backoffs don't yield cpu strands properly on
Niagara chips. Use pause instruction when available to achieve
this, otherwise use a benign instruction we know blocks the strand
for some time.
4) Wire up kcmp
5) Fix the build of various drivers by removing the unnecessary
blocking of OF_GPIO when SPARC.
6) Fix unintended regression wherein of_address_to_resource stopped
being provided. Fix from Andreas Larsson.
7) Fix NULL dereference in leon_handle_ext_irq(), also from Andreas
Larsson."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix build with mix of modular vs. non-modular crypto drivers.
sparc: Support atomic64_dec_if_positive properly.
of/address: sparc: Declare of_address_to_resource() as an extern function for sparc again
sparc32, leon: Check for existent irq_map entry in leon_handle_ext_irq
sparc: Add sparc support for platform_get_irq()
sparc: Allow OF_GPIO on sparc.
qlogicpti: Fix build warning.
sparc: Wire up sys_kcmp.
sparc64: Improvde documentation and readability of atomic backoff code.
sparc64: Use pause instruction when available.
sparc64: Fix cpu strand yielding.
sparc64: Make montmul/montsqr/mpmul usable in 32-bit threads.
This adds sparc support for platform_get_irq that in the normal case use
platform_get_resource() to get an irq. This standard approach fails for sparc as
there are no resources of type IORESOURCE_IRQ for irqs for sparc.
Cross platform drivers can then use this standard platform function and work on
sparc instead of having to have a special case for sparc.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fact, the callers of dev_pm_qos_add_request(),
dev_pm_qos_update_request() and dev_pm_qos_remove_request() for
requests of type DEV_PM_QOS_FLAGS need to ensure that the target
device is not RPM_SUSPENDED before using any of these functions (or
be prepared for the new PM QoS flags to take effect after the device
has been resumed). Document this in their kerneldoc comments.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Free a wrong point to struct dev_pm_qos->latency which suppose to
be the point to struct dev_pm_qos. The patch is to fix the issue.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e39473d (PM / QoS: Make it possible to expose PM QoS device
flags to user space) introduced __dev_pm_qos_update_request() to be
called internally by dev_pm_qos_update_request(), but forgot to make
the latter actually use the return value of the former. Fix this
mistake.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This seems to be the most common way of reporting register numbers, it's
certainly what we do for trace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This pulls in the various driver core changes that were in 3.7-rc3 into the
driver-core-next branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
* Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
* Fix for smp_processor_id() usage in preemptible code in powernow-k8 from
Andreas Herrmann.
* Fix for a suspend-related memory leak in cpufreq stats from Xiaobing Tu.
* Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD
in flush_old_exec() from Oleg Nesterov.
* acpi_processor_notify() fix from Alan Cox.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQivlUAAoJEKhOf7ml8uNsPHMP/jGv0umbDl0CrJBjd9eF+Tdt
52DpJ/c2HjghsmSG26MCsFVO026DcPoO/t7faUVpWiUy/I38TwyjTFMKrxouY5AC
8p929Gt5yjf/pB7w/P5C3exhv9zSWdVzCZ4rmlt7knBn7vN7jfI5Lv4kaEwAcu4o
mnGbUVzaFLaiHsKFa8iBOpkdr01Fn9FRINddMQ/+PdiFR+wkqOKMZBExjRoQgS31
aH90LL5Nfv5pSH126TH5S6GDdAXw0g4eHEfxGjNodEXdmAS+GXrD6QoGabab99ZD
SaZA41kTv3+ls4Z9uhhpNBgqEDQEWiNVBVfTs0PWTUpemYKlx85Ihdl8PbH1H0TM
QeHsM3dfHJsfhK/EjUFwx31oWrvfM0Qqw8CxOc/ASm2rpPOZVBgqRzKsqSMQE805
y3lteaoT9nObnKdy871QmIhAk3fN25u1txCtmNFc0S5VZyiAnD2RVS/a8y93gMse
5lxSMjOfUqvq3APlz4HIn3YovswjiAOOw0PlD3nK2qLj7tyEVOl5CMyL/05v58wJ
SeOic10v1oOEDYT3uM+aVERmK9APAsMbcecj7Xd5yqPu8NPx7zrj+z30wr0znS5x
KWnyZR83F4ZCb00geSZW0LliXuazjj+lWX/TFri9XY6ZdMvmTJOUVKBD8JwhHN0j
WH9iMOOBTMnJdbnf88sM
=8Tcc
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael J Wysocki:
- Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
- Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
- Fix for smp_processor_id() usage in preemptible code in powernow-k8
from Andreas Herrmann.
- Fix for a suspend-related memory leak in cpufreq stats from Xiaobing
Tu.
- Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD in
flush_old_exec() from Oleg Nesterov.
- acpi_processor_notify() fix from Alan Cox.
* tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: missing break
freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD
Fix memory leak in cpufreq stats.
cpufreq / powernow-k8: Remove usage of smp_processor_id() in preemptible code
PM / Domains: Fix memory leak on error path in pm_genpd_attach_cpuidle
ACPI: Fix memory leak in acpi_bind_one()
Here are a number of firmware core fixes for 3.7, and some other minor fixes.
And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCKwkIACgkQMUfUDdst+ynzUgCfQDwxUw1PVqQyWy7SakpsjFJJ
8kwAoITyjppn39v1WuZbg0+FZ6JpocyY
=2mDG
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are a number of firmware core fixes for 3.7, and some other minor
fixes. And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation:Chinese translation of Documentation/arm64/memory.txt
Documentation:Chinese translation of Documentation/arm64/booting.txt
Documentation:Chinese translation of Documentation/IRQ.txt
firmware loader: document kernel direct loading
sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()
dynamic_debug: Remove unnecessary __used
firmware loader: sync firmware cache by async_synchronize_full_domain
firmware loader: let direct loading back on 'firmware_buf'
firmware loader: fix one reqeust_firmware race
firmware loader: cancel uncache work before caching firmware
them together into a mca_config struct. This keeps them tightly and
neatly packed together instead of spilled all over the place.
Then, convert those which are used as booleans into real booleans and
save some space.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=EOHq
-----END PGP SIGNATURE-----
Merge tag 'mca_cfg' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull x86 RAS changes from Borislav Petkov:
"Rework all config variables used throughout the MCA code and collect
them together into a mca_config struct. This keeps them tightly and
neatly packed together instead of spilled all over the place.
Then, convert those which are used as booleans into real booleans and
save some space."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... which, analogous to DEVICE_INT_ATTR provides functionality to
set/clear bools. Its purpose is to be used where values need to be used
as booleans in configuration context.
Next patch uses this.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"This consists mainly of a set of one-liner fixes and cleanups for a
few minor issues identified in both Contiguous Memory Allocator code
and ARM DMA-mapping subsystem."
* 'fixes_for_linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: mm: Remove unused arm_vmregion priv field
ARM: dma-mapping: fix build warning in __dma_alloc()
ARM: dma-mapping: support debug_dma_mapping_error
mm: cma: alloc_contig_range: return early for err path
drivers: cma: Fix wrong CMA selected region size default value
drivers: dma-coherent: Fix typo in dma_mmap_from_coherent documentation
drivers: dma-contiguous: Don't redefine SZ_1M
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
val_bytes is of 'size_t', so it should be printed as '%zu'.
Fixes the following build warning on x86:
drivers/base/regmap/regmap.c:872:4: warning: format '%d' expects argument of type 'int', but argument 5 has type 'size_t' [-Wformat]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make the generic PM domains pm_genpd_poweroff() function take
device PM QoS flags into account when deciding whether or not to
remove power from the domain.
After this change the routine will return -EBUSY without executing
the domain's .power_off() callback if there is at least one PM QoS
flags request for at least one device in the domain and at least of
those request has at least one of the NO_POWER_OFF and REMOTE_WAKEUP
flags set.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: mark gross <markgross@thegnar.org>
Define two device PM QoS flags, PM_QOS_FLAG_NO_POWER_OFF
and PM_QOS_FLAG_REMOTE_WAKEUP, and introduce routines
dev_pm_qos_expose_flags() and dev_pm_qos_hide_flags() allowing the
caller to expose those two flags to user space or to hide them
from it, respectively.
After the flags have been exposed, user space will see two
additional sysfs attributes, pm_qos_no_power_off and
pm_qos_remote_wakeup, under the device's /sys/devices/.../power/
directory. Then, writing 1 to one of them will update the
PM QoS flags request owned by user space so that the corresponding
flag is requested to be set. In turn, writing 0 to one of them
will cause the corresponding flag in the user space's request to
be cleared (however, the owners of the other PM QoS flags requests
for the same device may still request the flag to be set and it
may be effectively set even if user space doesn't request that).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Acked-by: mark gross <markgross@thegnar.org>
Kconfig lists CMA_SIZE_SEL_ABSOLUTE as the default value fo the CMA
selected region size, but that option isn't available in the defined
choices. Set the default to CMA_SIZE_SEL_MBYTES instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
The function documentation incorrectly references dma_release_coherent.
Fix it. Don't mention a specific function name as dma_mmap_from_coherent
as multiple callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Use the definition from linux/sizes.h instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Modify the device PM QoS core code to support PM QoS flags requests.
First, add a new field of type struct pm_qos_flags called "flags"
to struct dev_pm_qos for representing the list of PM QoS flags
requests for the given device. Accordingly, add a new "type" field
to struct dev_pm_qos_request (along with an enum for representing
request types) and a new member called "flr" to its data union for
representig flags requests.
Second, modify dev_pm_qos_add_request(), dev_pm_qos_update_request(),
the internal routine apply_constraint() used by them and their
existing callers to cover flags requests as well as latency
requests. In particular, dev_pm_qos_add_request() gets a new
argument called "type" for specifying the type of a request to be
added.
Finally, introduce two routines, __dev_pm_qos_flags() and
dev_pm_qos_flags(), allowing their callers to check which PM QoS
flags have been requested for the given device (the caller is
supposed to pass the mask of flags to check as the routine's
second argument and examine its return value for the result).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: mark gross <markgross@thegnar.org>
The subsequent patches will use struct dev_pm_qos_request for
representing both latency requests and flags requests. To make that
easier, put the node member of struct dev_pm_qos_request (under the
name "pnode") into a union called "data" that will represent the
request's value and list node depending on its type.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: mark gross <markgross@thegnar.org>
Currently struct dev_pm_info contains only one PM QoS constraints
pointer reserved for latency requirements. Since one more device
constraints type (i.e. flags) will be necessary, introduce a new
structure, struct dev_pm_qos, that eventually will contain all of
the available device PM QoS constraints and replace the "constraints"
pointer in struct dev_pm_info with a pointer to the new structure
called "qos".
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
If pm_genpd_attach_cpudidle failed we leak memory stored in 'cpu_data'.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
async.c has provided synchronization mechanism on async_schedule_*,
so use async_synchronize_full_domain to sync caching firmware instead
of reinventing the wheel.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly 'firmware_buf' is introduced to make all loading requests
to share one firmware kernel buffer, so firmware_buf should
be used in direct loading for saving memory and speedup firmware
loading.
Secondly, the commit below
abb139e75c2cdbb955e840d6331cb5863e409d0e(firmware:teach
the kernel to load firmware files directly from the filesystem)
introduces direct loading for fixing udev regression, but it
bypasses the firmware cache meachnism, so this patch enables
caching firmware for direct loading case since it is still needed
to solve drivers' dependency during system resume.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several loading requests may be pending on one same
firmware buf, and this patch moves fw_map_pages_buf()
before complete_all(&fw_buf->completion) and let all
requests see the mapped 'buf->data' once the loading
is completed.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under 'Opportunistic sleep' situation, system sleep might be
triggered very frequently, so the uncahce work may not be completed
before caching firmware during next suspend.
This patch cancels the uncache work before caching firmware to
fix the problem above.
Also this patch optimizes the cacheing firmware mechanism a bit by
only storing one firmware cache entry for one firmware image.
So if the firmware is still cached during suspend, it doesn't need
to be loaded from user space any more.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap_mmio and regmap_irq depend on regmap core, if not select,
we may not compile regmap core and meet compiling errors as follows
if REGMAP_MMIO is selected by client drivers:
drivers/mfd/syscon.c:94:15: error: variable 'syscon_regmap_config' has initializer but incomplete type
drivers/mfd/syscon.c:95:2: error: unknown field 'reg_bits' specified in initializer
drivers/mfd/syscon.c:95:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:95:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c:96:2: error: unknown field 'val_bits' specified in initializer
drivers/mfd/syscon.c:96:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:96:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c:97:2: error: unknown field 'reg_stride' specified in initializer
drivers/mfd/syscon.c:97:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:97:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c: In function 'syscon_probe':
drivers/mfd/syscon.c:124:2: error: invalid use of undefined type 'struct regmap_config'
drivers/mfd/syscon.c:125:2: error: implicit declaration of function 'devm_regmap_init_mmio' [-Werror=implicit-function-declaration]
drivers/mfd/syscon.c:125:17: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
drivers/mfd/Kconfig:
config MFD_SYSCON
bool "System Controller Register R/W Based on Regmap"
depends on OF
select REGMAP_MMIO
help
Select this option to enable accessing system control registers
via regmap.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is sometimes convenient for a regmap user to override the standard
regmap lock/unlock functions with custom functions.
For instance this can be useful in case an already existing spinlock
or mutex has to be used for locking a set of registers instead of the
internal regmap spinlock/mutex.
Note that the fast_io field of struct regmap_bus is ignored in case
custom locking functions are used.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Building regmap.o triggers this GCC warning:
drivers/base/regmap/regmap.c: In function ‘regmap_raw_read’:
drivers/base/regmap/regmap.c:1172:6: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Long story short: Jakub Jelinek pointed out that there is a type
mismatch between 'num' in regmap_volatile_range() and 'val_count' in
regmap_raw_read(). And indeed, converting 'num' to the type of
'val_count' (ie, size_t) makes this warning go away.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a block write covers a paged memory region and crosses a window
boundary then rather than failing the write split the transfer up
into multiple writes, making the whole process more transparent for
drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The range code was written to check for return codes less than zero as
errors but throughout the rest of the API return codes not equal to zero
are errors. Change all these checks to match the house style.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a register range is named then provide a debugfs file showing the
contents of the range separately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than just returning a single error code for every possible thing we
can notice print an error message saying what the problem was. This makes
it very much easier to figure out what's wrong and fix it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This makes things consistent with the rest of the API and is actually what
the documentation says. We don't currently have any in tree users so low
cost.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is useful for integration with other subsystems, especially MFD,
and provides an alternative API for users that request their own IRQs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
remove_memory() will be called when hot removing a memory device. But
even if offlining memory, we cannot notice it. So the patch updates the
memory block's state and sends notification to userspace.
Additionally, the memory device may contain more than one memory block.
If the memory block has been offlined, __offline_pages() will fail. So we
should try to offline one memory block at a time.
Thus remove_memory() also check each memory block's state. So there is no
need to check the memory block's state before calling remove_memory().
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove_memory() is called in two cases:
1. echo offline >/sys/devices/system/memory/memoryXX/state
2. hot remove a memory device
In the 1st case, the memory block's state is changed and the notification
that memory block's state changed is sent to userland after calling
remove_memory(). So user can notice memory block is changed.
But in the 2nd case, the memory block's state is not changed and the
notification is not also sent to userspcae even if calling
remove_memory(). So user cannot notice memory block is changed.
For adding the notification at memory hot remove, the patch just prepare
as follows:
1st case uses offline_pages() for offlining memory.
2nd case uses remove_memory() for offlining memory and changing memory block's
state and notifing the information.
The patch does not implement notification to remove_memory().
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fengguang correctly points out that the firmware reading should not use
vfs_read(), since the buffer is in kernel space.
The vfs_read() just happened to work for kernel threads, but sparse
warns about the incorrect address spaces, and it's definitely incorrect
and could fail for other users of the firmware loading.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a first step in allowing people to by-pass udev for loading
device firmware. Current versions of udev will deadlock (causing us to
block for the 30 second timeout) under some circumstances if the
firmware is loaded as part of the module initialization path, and this
is causing problems for media drivers in particular.
The current patch hardcodes the firmware path that udev uses by default,
and will fall back to the legacy udev mode if the firmware cannot be
found there. We'd like to add support for both configuring the paths
and the fallback behaviour, but in the meantime this hopefully fixes the
immediate problem, while also giving us a way forward.
[ v2: Some VFS layer interface cleanups suggested by Al Viro ]
[ v3: use the default udev paths suggested by Kay Sievers ]
Suggested-by: Ivan Kalvachev <ikalvachev@gmail.com>
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kay Sievers <kay@redhat.com>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs update from Al Viro:
- big one - consolidation of descriptor-related logics; almost all of
that is moved to fs/file.c
(BTW, I'm seriously tempted to rename the result to fd.c. As it is,
we have a situation when file_table.c is about handling of struct
file and file.c is about handling of descriptor tables; the reasons
are historical - file_table.c used to be about a static array of
struct file we used to have way back).
A lot of stray ends got cleaned up and converted to saner primitives,
disgusting mess in android/binder.c is still disgusting, but at least
doesn't poke so much in descriptor table guts anymore. A bunch of
relatively minor races got fixed in process, plus an ext4 struct file
leak.
- related thing - fget_light() partially unuglified; see fdget() in
there (and yes, it generates the code as good as we used to have).
- also related - bits of Cyrill's procfs stuff that got entangled into
that work; _not_ all of it, just the initial move to fs/proc/fd.c and
switch of fdinfo to seq_file.
- Alex's fs/coredump.c spiltoff - the same story, had been easier to
take that commit than mess with conflicts. The rest is a separate
pile, this was just a mechanical code movement.
- a few misc patches all over the place. Not all for this cycle,
there'll be more (and quite a few currently sit in akpm's tree)."
Fix up trivial conflicts in the android binder driver, and some fairly
simple conflicts due to two different changes to the sock_alloc_file()
interface ("take descriptor handling from sock_alloc_file() to callers"
vs "net: Providing protocol type via system.sockprotoname xattr of
/proc/PID/fd entries" adding a dentry name to the socket)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (72 commits)
MAX_LFS_FILESIZE should be a loff_t
compat: fs: Generic compat_sys_sendfile implementation
fs: push rcu_barrier() from deactivate_locked_super() to filesystems
btrfs: reada_extent doesn't need kref for refcount
coredump: move core dump functionality into its own file
coredump: prevent double-free on an error path in core dumper
usb/gadget: fix misannotations
fcntl: fix misannotations
ceph: don't abuse d_delete() on failure exits
hypfs: ->d_parent is never NULL or negative
vfs: delete surplus inode NULL check
switch simple cases of fget_light to fdget
new helpers: fdget()/fdput()
switch o2hb_region_dev_write() to fget_light()
proc_map_files_readdir(): don't bother with grabbing files
make get_file() return its argument
vhost_set_vring(): turn pollstart/pollstop into bool
switch prctl_set_mm_exe_file() to fget_light()
switch xfs_find_handle() to fget_light()
switch xfs_swapext() to fget_light()
...
Pull CMA and DMA-mapping updates from Marek Szyprowski:
"This time the pull request is rather small, because the further
redesign patches were not ready on time.
This pull request consists of the patches which extend ARM DMA-mapping
subsystem with support for CPU coherent (ACP) DMA busses. The first
client of the new version is HighBank SATA driver. The second part of
the pull request includes various cleanup for both CMA common code and
ARM DMA-mapping subsystem."
Fix up trivial add-add conflict due to the "dma-coherent" DT property
being added next to the "calxeda,port-phys" property for the Calxeda
AHCI controller.
* 'for-v3.7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: Remove unsed var at arm_coherent_iommu_unmap_page
ARM: highbank: add coherent DMA setup
ARM: kill off arch_is_coherent
ARM: add coherent iommu dma ops
ARM: add coherent dma ops
ARM: dma-mapping: Refrain noisy console message
ARM: dma-mapping: Small logical clean up
drivers: dma-contiguous: refactor dma_alloc_from_contiguous()
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
The dma_alloc_from_contiguous() function returns either a valid pointer
to a page structure or NULL, the error code set when pageno >= cma->count
is not used at all and can be safely removed.
This commit also changes the function to avoid goto and have only one exit
path and one place where mutex is unlocked.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
[fixed compilation break caused by missing semicolon]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago), and
some hyper-v updates and some printk fixes as well. All patches that
are outside of the drivers/base area have been acked by the respective
maintainers, and have all been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3vkACgkQMUfUDdst+ylQoACgldktGFgkCLzH+rGYthrXOC5P
9hUAnjmOhdoHlMTL81vWTlH+BrGernym
=khrr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core merge from Greg Kroah-Hartman:
"Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago),
and some hyper-v updates and some printk fixes as well. All patches
that are outside of the drivers/base area have been acked by the
respective maintainers, and have all been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
memory: tegra{20,30}-mc: Fix reading incorrect register in mc_readl()
device.h: Add missing inline to #ifndef CONFIG_PRINTK dev_vprintk_emit
memory: emif: Add ifdef CONFIG_DEBUG_FS guard for emif_debugfs_[init|exit]
Documentation: Fixes some translation error in Documentation/zh_CN/gpio.txt
Documentation: Remove 3 byte redundant code at the head of the Documentation/zh_CN/arm/booting
Documentation: Chinese translation of Documentation/video4linux/omap3isp.txt
device and dynamic_debug: Use dev_vprintk_emit and dev_printk_emit
dev: Add dev_vprintk_emit and dev_printk_emit
netdev_printk/netif_printk: Remove a superfluous logging colon
netdev_printk/dynamic_netdev_dbg: Directly call printk_emit
dev_dbg/dynamic_debug: Update to use printk_emit, optimize stack
driver-core: Shut up dev_dbg_reatelimited() without DEBUG
tools/hv: Parse /etc/os-release
tools/hv: Check for read/write errors
tools/hv: Fix exit() error code
tools/hv: Fix file handle leak
Tools: hv: Implement the KVP verb - KVP_OP_GET_IP_INFO
Tools: hv: Rename the function kvp_get_ip_address()
Tools: hv: Implement the KVP verb - KVP_OP_SET_IP_INFO
Tools: hv: Add an example script to configure an interface
...
This reverts commit fc2fb3a075.
The problem with the above commit is that it makes the device PM QoS
core code hold a spinlock around blocking_notifier_call_chain()
invocations.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There are several drivers where the return value of
pm_runtime_get_sync() is used to decide whether or not it is safe to
access hardware and that don't provide .suspend() callbacks for system
suspend (but may use late/noirq callbacks.) If such a driver happens
to call pm_runtime_get_sync() during system suspend, after the core
has disabled runtime PM, it will get the error code and will decide
that the hardware should not be accessed, although this may be a wrong
conclusion, depending on the state of the device when runtime PM was
disabled.
Drivers might work around this problem by using a test like:
ret = pm_runtime_get_sync(dev);
if (!ret || (ret == -EACCES && driver_private_data(dev)->suspended)) {
/* access hardware */
}
where driver_private_data(dev)->suspended is a flag set by the
driver's .suspend() method (that would have to be added for this
purpose). However, that potentially would need to be done by multiple
drivers which means quite a lot of duplicated code and bloat.
To avoid that we can use the observation that the core sets
dev->power.is_suspended before disabling runtime PM and use that
instead of the driver's private flag. Still, potentially many drivers
would need to repeat that same check in quite a few places, so it's
better to let the core do it.
Then we can be a bit smarter and check whether or not runtime PM was
disabled by the core only (disable_depth == 1) or by someone else in
addition to the core (disable_depth > 1). In the former case
rpm_resume() can return 1 if the runtime PM status is RPM_ACTIVE,
because it means the device was active when the core disabled runtime
PM. In the latter case it should still return -EACCES, because it
isn't clear why runtime PM has been disabled.
Tested on AM3730/Beagle-xM where a wakeup IRQ firing during the late
suspend phase triggers runtime PM activity in the I2C driver since the
wakeup IRQ is on an I2C-connected PMIC.
[rjw: Modified whitespace to follow the file's convention.]
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1591) moves the pm_runtime_get_noresume() and
pm_runtime_put_sync() calls from __device_suspend() and
device_resume() to device_prepare() and device_complete() in the PM
core.
The reason for doing this is to make sure that parent devices remain
at full power (i.e., don't go into runtime suspend) while their
children are being resumed from a system sleep.
The PCI core already contained equivalent code to serve the same
purpose. The patch removes the duplicated code, since it is no longer
needed. One of the comments from the PCI core gets moved into the PM
core, and a second comment is added to explain whe the _get_noresume
and _put_sync calls are present.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The per-device PM QoS locking requires a spinlock to be used. The reasons
are:
- an alignement with the PM QoS core code, which is used by the per-device
PM QoS code for the constraints lists management. The PM QoS core code
uses spinlocks to protect the constraints lists,
- some drivers need to use the per-device PM QoS functionality from
interrupt context or spinlock protected context.
An example of such a driver is the OMAP HSI (high-speed synchronous serial
interface) driver which needs to control the IP block idle state
depending on the FIFO empty state, from interrupt context.
Reported-by: Djamil Elaidi <d-elaidi@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When dpm_suspend_noirq fail, state is PMSG_SUSPEND,
should change to PMSG_RESUME when dpm_resume_early is called
Signed-off-by: Feng Hong <hongfeng@marvell.com>
Signed-off-by: Raul Xiong <xjian@marvell.com>
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* pm-cpufreq:
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
acpi-cpufreq: Add compatibility for legacy AMD cpb sysfs knob
acpi-cpufreq: Add support for disabling dynamic overclocking
ACPI: Add fixups for AMD P-state figures
powernow-k8: delay info messages until initialization has succeeded
cpufreq: Add warning message to powernow-k8
acpi-cpufreq: Add quirk to disable _PSD usage on all AMD CPUs
acpi-cpufreq: Add support for modern AMD CPUs
cpufreq / powernow-k8: Fixup missing _PSS objects message
PM / cpufreq: Initialise the cpu field during conservative governor start
* pm-sleep:
properly __init-annotate pm_sysrq_init()
PM / wakeup: Use irqsave/irqrestore for events_lock
PM / Freezer: Fix small typo "regrigerator"
PM / Sleep: Print name of wakeup source that aborts suspend
* pm-domains:
PM / Domains: Fix compilation warning related to genpd_start_dev_no_timing()
PM / Domains: Operations related to cpuidle using domain names
PM / Domains: Document cpuidle-related functions and change their names
PM / Domains: Add power-on function using names to identify domains
PM / Domains: Make it possible to use names when adding subdomains
PM / Domains: Make it possible to use domain names when adding devices
* pm-timers:
PM: Do not use the syscore flag for runtime PM
sh: MTU2: Basic runtime PM support
sh: CMT: Basic runtime PM support
sh: TMU: Basic runtime PM support
PM / Domains: Do not measure start time for "irq safe" devices
PM / Domains: Move syscore flag from subsys data to struct device
PM / Domains: Rename the always_on device flag to syscore
PM / Runtime: Allow helpers to be called by early platform drivers
PM: Reorganize device PM initialization
sh: MTU2: Introduce clock events suspend/resume routines
sh: CMT: Introduce clocksource/clock events suspend/resume routines
sh: TMU: Introduce clocksource/clock events suspend/resume routines
timekeeping: Add suspend and resume of clock event devices
PM / Domains: Add power off/on function for system core suspend stage
PM / Domains: Introduce simplified power on routine for system resume
Convert direct calls of vprintk_emit and printk_emit to the
dev_ equivalents.
Make create_syslog_header static.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add utility functions to consolidate the use of
create_syslog_header and vprintk_emit.
This allows conversion of logging functions that
call create_syslog_header and then call vprintk_emit
or printk_emit to the dev_ equivalents.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4e00daaa9
("driver-core: extend dev_printk() to pass structured data")
changed __dev_printk and broke dynamic-debug's ability to control the
dynamic prefix of dev_dbg(dev,..).
commit af7f2158fd
("drivers-core: make structured logging play nice with dynamic-debug")
made a minimal correction.
The current dynamic debug code uses up to 3 recursion levels via %pV.
This can consume quite a bit of stack. Directly call printk_emit to
reduce the recursion depth.
These changes include:
dev_dbg:
o Create and use function create_syslog_header to format the syslog
header for printk_emit uses.
o Call create_syslog_header and neaten __dev_printk
o Make __dev_printk static not global
o Remove include header declaration of __dev_printk
o Remove now unused EXPORT_SYMBOL() of __dev_printk
o Whitespace neatening
dynamic_dev_dbg:
o Remove KERN_DEBUG from dynamic_emit_prefix
o Call create_syslog_header and printk_emit
o Whitespace neatening
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the previous macro of CONFIG_PM with
CONFIG_PM_SLEEP becasue firmware cache is only used in
system sleep situations.
Also this patch fixes the below compile warning when
CONFIG_PM=n:
drivers/base/firmware_class.c:1147: warning: 'device_cache_fw_images'
defined but not used
drivers/base/firmware_class.c:1212: warning:
'device_uncache_fw_images_delay' defined but not used
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a lot of devices booting from device tree nowadays, it requires
that OPP table can be initialized from device tree. The patch adds
a helper function of_init_opp_table together with a binding doc for
that purpose.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The primary handler will NOT be called if the interrupt nests into
another interrupt thread. Remove it to avoid confusing.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After starting caching firmware, there is still some time left
before devices are suspended, during the period, request_firmware
or its nowait version may still be triggered by the below situations
to load firmware images which can't be cached during suspend/resume
cycle.
- new devices added
- driver bind
- or device open kind of things
This patch utilizes the piggyback trick to cache firmware for
this kind of situation: just increase the firmware buf's reference
count and add the fw name entry into cache entry list after starting
caching firmware and before syscore_suspend() is called.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the requested firmware image doesn't exist, firmware->priv
should be set for the later concurrent requests, otherwise
warning and oops will be triggered inside firmware_free_data().
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jon Medhurst (Tixy) recently noticed a problem with the
events_lock usage. One of the Android patches that uses
wakeup_sources calls wakeup_source_add() with irqs disabled.
However, the event_lock usage in wakeup_source_add() uses
spin_lock_irq()/spin_unlock_irq(), which reenables interrupts.
This results in lockdep warnings.
The fix is to use spin_lock_irqsave()/spin_lock_irqrestore()
instead for the events_lock.
References: https://bugs.launchpad.net/linaro-landing-team-arm/+bug/1037565
Reported-and-debugged-by: Jon Medhurst (Tixy) <tixy@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Function genpd_start_dev_no_timing was accessed inside CONFIG_PM_RUNTIME
macro but defined outside it. When the above macro was not defined the
compiler gave the following warning:
drivers/base/power/domain.c:96:12: warning:
‘genpd_start_dev_no_timing’ defined but not used [-Wunused-function]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Safety check for the validity of the resource name before calling strcmp().
If the resource name is NULL do not compare it, just skip it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it possible to use domain names in operations connecting cpuidle
to and disconnecting it from a PM domain. This is useful on
platforms where PM domain objects are organized in such a way that
the names of the domains are easier to use than the addresses of
those objects.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The names of the cpuidle-related functions in
drivers/base/power/domain.c are inconsistent with the names of the
other exported functions in that file (the "pm_" prefix is missing
from them) and they are missing kerneldoc comments.
Fix that by adding the missing "pm_" prefix to the names of those
functions and add kerneldoc comments documenting them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It sometimes is necessary to turn on a given PM domain when only
the name of it is known and the domain pointer is not readily
available. For this reason, add a new helper function,
pm_genpd_name_poweron(), allowing the caller to turn on a PM domain
using its name for identification. To avoid code duplication,
move the domain lookup code to a separate function.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a new helper function, pm_genpd_add_subdomain_names(), allowing
the caller to add a subdomain to a generic PM domain using names for
domain identification (both domains have to be initialized before).
This function is useful for adding subdomains to PM domains whose
representations are stored in tables, when the caller doesn't know
the indices of the domain to add the subdomain to and of the
subdomain itself, but it knows the domains' names.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a new helper function __pm_genpd_name_add_device() allowing
a device to be added to a (registered) generic PM domain identified
by name. Add a wrapper around it, pm_genpd_name_add_device(),
passing NULL as the last argument and reorganize pm_domains.h for the
new functions to be defined consistently with the existing ones.
These functions are useful for adding devices to PM domains whose
representations are stored in tables, when the caller doesn't know
the index of the domain to add the device to, but it knows the
domain's name.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The syscore device PM flag used to mark the devices (belonging to
PM domains) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages, need not be
accessed by the runtime PM core functions, because all of the devices
it is set for need to be marked as "irq safe" anyway and are
protected from being turned off by runtime PM by ensuring that their
usage counters are always set.
For this reason, make the syscore flag system-wide PM-specific
and simplify the code used for manipulating it, because it need not
acquire the device's power.lock any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The genpd_start_dev() routine used by pm_genpd_runtime_resume()
to put "irq safe" devices into the full power state measures the
time necessary to "start" the device and updates its PM QoS timing
data if necessary. This may lead to a deadlock if the given device
is a clock source and genpd_start_dev() is invoked from within the
clock source's .enable() routine, which will happen if that routine
uses pm_runtime_get_sync(), for example, to ensure that the device
is operational.
For this reason, introduce a special routine analogous to
genpd_start_dev(), called genpd_start_dev_no_timing(), that doesn't
carry out the time measurement, and make pm_genpd_runtime_resume()
use it instead of genpd_start_dev() to power up "irq safe" devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The syscore device PM flag is used to mark the devices (belonging to
a PM domain) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages. That flag is
stored in the device's struct pm_subsys_data object whose address is
available from struct device. However, in some situations it may be
convenient to set that flag before the device is added to a PM
domain, so it is better to move it directly to the "power" member of
struct device. Then, it can be checked by the routines in
drivers/base/power/runtime.c and drivers/base/power/main.c, which is
more straightforward.
This also reduces the number of dev_gpd_data() invocations in the
generic PM domains framework, so the overhead related to the syscore
flag is slightly smaller.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The always_on device flag is used to mark the devices (belonging to
a PM domain) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages. Change name
of that flag to "syscore" to better reflect its purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Runtime PM helper functions, like pm_runtime_get_sync(), cannot be
called by early platform device drivers, because the devices' power
management locks are not initialized at that time. This is quite
inconvenient, so modify early_platform_add_devices() to initialize
the devices power management locks as appropriate and make sure that
they won't be initialized more than once if an early platform
device is going to be used as a regular one later.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Make the device power management initialization more straightforward
by moving the initialization of common (i.e. used by both runtime PM
and system suspend) fields to a separate routine.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce function pm_genpd_syscore_switch() and two wrappers around
it, pm_genpd_syscore_poweroff() and pm_genpd_syscore_poweron(),
allowing the callers to let the generic PM domains framework know
that the given device is not necessary any more and its PM domain
can be turned off (the former) or that the given device will be
required immediately, so its PM domain has to be turned on (the
latter) during the system core (syscore) stage of system suspend
(or hibernation) and resume.
These functions will be used for handling devices registered as
clock sources and clock event devices that belong to PM domains.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce function pm_genpd_sync_poweron() for restoring domain power
during resume from system suspend and hibernation. It can be much
simpler than pm_genpd_poweron(), because it doesn't have to care
about locking and it can skip many checks done by the latter.
Modify pm_genpd_resume_noirq() and pm_genpd_restore_noirq() to use
the new function.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, regmap will write 1 to mask_base to mask
an interrupt and write 0 to unmask it.
But some chips do not have an interrupt mask register,
and only have interrupt enable register.
Then we should write 0 to disable interrupt and 1 to enable.
So add an mask_invert flag to handle this.
If it is not set, behavior is same as previous.
If set it to 1, the mask value will be inverted
before written to mask_base
Signed-off-by: Xiaofan Tian <tianxf@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Contiguous Memory Allocator requires each of its regions to be aligned
in such a way that it is possible to change migration type for all
pageblocks holding it and then isolate page of largest possible order from
the buddy allocator (which is MAX_ORDER-1). This patch relaxes alignment
requirements by one order, because MAX_ORDER alignment is not really
needed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Here is one fix for the dmesg line corruption problem that the previous
set of patches caused.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAyh14ACgkQMUfUDdst+yn2RQCbBissjdBqDhaX9schGTKyrxPM
UOUAn3o3KZpUzFWSGYXQGaSI7HtcyElz
=GWkA
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull one more driver core fix from Greg Kroah-Hartman:
"Here is one fix for the dmesg line corruption problem that the
previous set of patches caused.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
dyndbg: fix for SOH in logging messages
commit af7f2158fd was done against master, and clashed with structured
logging's change of KERN_LEVEL to SOH.
Bisected and fixed by Markus Trippelsdorf.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Baron <jbaron@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Fixes for three obscure problems in the runtime PM core code found recently.
* Two fixes for the new "coupled" cpuidle code from Colin Cross and
Jon Medhurst.
* intel_idle driver fix from Konrad Rzeszutek Wilk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJQMAOWAAoJEKhOf7ml8uNswp0QAK2pHmZMU8Pg3mY0Qlovvcmn
KordhSahzwodvdKMpzGqjk/TO3kJ0dk8YGBY1qIzSySmE6S9qsJKQaaoiNR0Se83
5ZpGVNfJpFBwzrHQkOMkaZzirC5gegKVykM6jlvh3oZqgqGWDawnzOsGCJvYv0lI
fSAgIc0CDB2dK5V9zFduXp3Cjv2cGEgW/Dd3ggPYns9JZJTAcHuD6cPdSQVml0JG
vk2VA1IjqRYyn9eSIOerezwh7iVCrAF5miiADXkaTD1fQ9ZyHYfxuqwM1jpijlkz
PEuICp4FJ4MTPjKYcJgJct0vdc0uD60dvHz9k7PxDIQ35eFiYJYeSU70oNCqULVh
lhN0VWqUZI1m7U/jH3f/pCc5x4jVhwQvuEE7yIz8d7nclhWqpBElZgyZ8B3yQiR0
JSChvGtLgYdXYnk6epw4sL6EZpqQW9Xk/JPJpyEy6KAIY45p8q/a972OmGU35ltN
qAkeBVcAW836NzgnHPJs17R6VzhxFFegd38NbqRvRsVL0Og9+RoT8P9gt2ZPoQ7O
jBGT/iKn1GzMSTpDGbgj9Nf3tm1zs+pvZ2fc/niBZH/72eyLQVs8zgm0TJVrTA26
uKeE7l+R3UrsMhBO28kFsX37q3gOYBjtf2K7u2W1q71aNE6YcXdfJfd2aGDZ1LTQ
1d9MuFjbR6hKQE2Mb7YH
=fO1w
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
- Fixes for three obscure problems in the runtime PM core code found
recently.
- Two fixes for the new "coupled" cpuidle code from Colin Cross and Jon
Medhurst.
- intel_idle driver fix from Konrad Rzeszutek Wilk.
* tag 'pm-for-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: Check cpu_idle_get_driver() for NULL before dereferencing it.
cpuidle: Prevent null pointer dereference in cpuidle_coupled_cpu_notify
cpuidle: coupled: fix sleeping while atomic in cpu notifier
PM / Runtime: Check device PM QoS setting before "no callbacks" check
PM / Runtime: Clear power.deferred_resume on success in rpm_suspend()
PM / Runtime: Fix rpm_resume() return value for power.no_callbacks set
A driver or app may repeatedly request a wakeup source while the system
is attempting to enter suspend, which may indicate a bug or at least
point out a highly active system component that is responsible for
decreased battery life on a mobile device. Even when the incidence
of suspend abort is not severe, identifying wakeup sources that
frequently abort suspend can be a useful clue for power management
analysis.
In some cases the existing stats can point out the offender where there is
an unexpectedly high activation count that stands out from the others, but
in other cases the wakeup source frequently taken just after the rest of
the system thinks its time to suspend might not stand out in the overall
stats.
It is also often useful to have information about what's been happening
recently, rather than totals of all activity for the system boot.
It's suggested to dump a line about which wakeup source
aborted suspend to aid analysis of these situations.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If __dev_pm_qos_read_value(dev) returns a negative value,
rpm_suspend() should return -EPERM for dev even if its
power.no_callbacks flag is set. For this to happen, the device's
power.no_callbacks flag has to be checked after the PM QoS check,
so move the PM QoS check to rpm_check_suspend_allowed() (this will
make it cover idle notifications as well as runtime suspend too).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
The power.deferred_resume can only be set if the runtime PM status
of device is RPM_SUSPENDING and it should be cleared after its
status has been changed, regardless of whether or not the runtime
suspend has been successful. However, it only is cleared on
suspend failure, while it may remain set on successful suspend and
is happily leaked to rpm_resume() executed in that case.
That shouldn't happen, so if power.deferred_resume is set in
rpm_suspend() after the status has been changed to RPM_SUSPENDED,
clear it before calling rpm_resume(). Then, it doesn't need to be
cleared before changing the status to RPM_SUSPENDING any more,
because it's always cleared after the status has been changed to
either RPM_SUSPENDED (on success) or RPM_ACTIVE (on failure).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
For devices whose power.no_callbacks flag is set, rpm_resume()
should return 1 if the device's parent is already active, so that
the callers of pm_runtime_get() don't think that they have to wait
for the device to resume (asynchronously) in that case (the core
won't queue up an asynchronous resume in that case, so there's
nothing to wait for anyway).
Modify the code accordingly (and make sure that an idle notification
will be queued up on success, even if 1 is to be returned).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Here are two tiny patches, one fixing a dynamic debug problem that the printk
rework turned up, and the other one fixing an extcon problem that people
reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAueMIACgkQMUfUDdst+ymSRACgsoRAFYZMSG2bSCkM3LBHVpo6
w1wAoMrN+5ooCJfnWrRftn/s0M7Tpocc
=o7Cx
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are two tiny patches, one fixing a dynamic debug problem that the
printk rework turned up, and the other one fixing an extcon problem
that people reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: extcon_gpio: Replace gpio_request_one by devm_gpio_request_one
drivers-core: make structured logging play nice with dynamic-debug
device_cache_fw_images need to iterate devices in system,
so this patch applies the introduced dpm_for_each_dev to
avoid link failure if CONFIG_FW_LOADER is m.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dpm_list and its pm lock provide a good way to iterate all
devices in system. Except this way, there is no other easy
way to iterate devices in system.
firmware loader need to cache firmware images for devices
before system sleep, so introduce the function to meet its
demand.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'return 0' should be added to fw_pm_notify if !PM because
return value of the funcion is defined as 'int'.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implements caching devices' firmware automatically
during system syspend/resume cycle, so any device drivers can
call request_firmware or request_firmware_nowait inside resume
path to get the cached firmware if they have loaded firmwares
successfully at least once before entering suspend.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because device_cache_fw_images only cache the firmware which has been
loaded sucessfully at leat once, using a small loading timeout should
be reasonable.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the three helpers below:
void device_cache_fw_images(void)
void device_uncache_fw_images(void)
void device_uncache_fw_images_delay(unsigned long)
so we can use device_cache_fw_images() to cache firmware for
all devices which need firmware to work, and the device driver
can get the firmware easily from kernel memory when system isn't
ready for completing requests of loading firmware.
After system is ready for completing firmware loading, driver core
will call device_uncache_fw_images() or its delay version to free
the cached firmware.
The above helpers will be used to cache device firmware during
system suspend/resume cycle in the following patches.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces one devres API of devres_for_each_res
so that the device's driver can iterate each resource it has
interest in.
The firmware loader will use the API to get each firmware name
from the device instance.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch will store firmware name into devres list of the device
which is requesting firmware loading, so that we can implement
auto cache and uncache firmware for devices in need.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
request_firmware_nowait is allowed to be called in atomic
context now if @gfp is GFP_ATOMIC, so fix the obsolete
comments and states which situations are suitable for using
it.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Callers of request_firmware* must hold the reference count of
@device, otherwise it is easy to trigger oops since the firmware
loader device is the child of @device.
This patch adds comments about the usage. In fact, most of drivers
call request_firmware* in its probe() or open(), so the constraint
should be reasonable and can be satisfied.
Also this patch holds the reference count of @device before
schedule_work() in request_firmware_nowait() to avoid that
the @device is released after request_firmware_nowait returns
and before the worker function is scheduled.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches introduce two kernel APIs of cache_firmware and
uncache_firmware, both of which take the firmware file name
as the only parameter.
So any drivers can call cache_firmware to cache the specified
firmware file into kernel memory, and can use the cached firmware
in situations which can't request firmware from user space.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch always let firmware_buf own the pages buffer allocated
inside firmware_data_write, and add all instances of firmware_buf
into the firmware cache global list. Also introduce one private field
in 'struct firmware', so release_firmware will see the instance of
firmware_buf associated with the current firmware instance, then just
'free' the instance of firmware_buf.
The firmware_buf instance represents one pages buffer for one
firmware image, so lots of firmware loading requests can share
the same firmware_buf instance if they request the same firmware
image file.
This patch will make implementation of the following cache_firmware/
uncache_firmware very easy and simple.
In fact, the patch improves request_formware/release_firmware:
- only request userspace to write firmware image once if
several devices share one same firmware image and its drivers
call request_firmware concurrently.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces struct firmware_buf to describe the buffer
which holds the firmware data, which will make the following
cache_firmware/uncache_firmware implemented easily.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If one device driver calls request_firmware_nowait() to request
several different firmwares' loading, device_add() will return
failure since all firmware loader device use same name of the
device who is requesting firmware.
This patch always use the name of firmware image as the firmware
loader device name to fix the problem since the following patches
for caching firmware will make sure only one loading for same
firmware is alllowd at the same time.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wmb() inside fw_load_abort is not necessary, since
complete() and wait_on_completion() has implied one pair
of memory barrier.
Also wmb() isn't a correct usage, so just remove it.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes two races in loading firmware:
1, FW_STATUS_DONE should be set before waking up the task waitting
on _request_firmware_load, otherwise FW_STATUS_ABORT may be
thought as DONE mistakenly.
2, Inside _request_firmware_load(), there is a small window between
wait_for_completion() and mutex_lock(&fw_lock), and 'echo 1 > loading'
still may happen during the period, so this patch checks FW_STATUS_DONE
to prevent pages' buffer completed from being freed in firmware_loading_store.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch doesn't transfer ownership of pages' buffer to the
instance of firmware until the firmware loading is completed,
which will simplify firmware_loading_store a lot, so help
to introduce the following cache_firmware and uncache_firmware
mechanism during system suspend-resume cycle.
In fact, this patch fixes one bug: if writing data into
firmware loader device is bypassed between writting 1 and 0 to
'loading', OOPS will be triggered without the patch.
Also handle the vmap failure case, and add some comments to make
code more readable.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we have support for explicit platform device IDs, as well as
ID-less platform devices when a given device type can only have one
instance. However there are cases where multiple instances of a device
type can exist, and their IDs aren't (and can't be) known in advance
and do not matter. In that case we need automatic device IDs to avoid
device name collisions.
I am using magic ID value -2 (PLATFORM_DEVID_AUTO) for this, similar
to -1 for ID-less devices. The automatically allocated device IDs are
global (to avoid an additional per-driver cost.) We keep note that the
ID was automatically allocated so that it can be freed later.
Note that we also restore the ID to PLATFORM_DEVID_AUTO on error and
device deletion, to avoid avoid unexpected behavior on retry. I don't
really expect retries on platform device addition, but better safe
than sorry.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_del can happen anytime, so once it happens,
the devres of the device will be freed inside device_del, but
drivers can't know it has been deleted and may still add
resources into the device, so memory leak is caused.
This patch moves the devres_release_all to fix the problem.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4e00daaa9 changed __dev_printk
in a way that broke dynamic-debug's ability to control the dynamic
prefix of dev_dbg(dev,..), but not dev_dbg(NULL,..) or pr_debug(..),
which is why it wasnt noticed sooner.
When dev==NULL, __dev_printk() just calls printk(), which just works.
But otherwise, it assumed that level was always a string like "<L>"
and just plucked out the 'L', ignoring the rest. However,
dynamic_emit_prefix() adds "[tid] module:func:line:" to the string,
those additions all got lost.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Cc: stable <stable@vger.kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commits 1d5fcfec22 (PM / Domains: Add device domain data reference
counter) and 62d4490294 (PM / Domains: Allow device callbacks to be
added at any time) added checks for the return value of
dev_pm_get_subsys_data(), but those checks were incorrect, because
that function returned 1 on success in some cases.
Since all of the existing users of dev_pm_get_subsys_data() don't use
the positive value returned by it on success, change its definition
so that it always returns 0 when successful.
Reported-by: Heiko Stübner <heiko@sntech.de>
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some devices need to have a runtime PM reference while handling interrupts
to ensure that the register I/O is available. Support this with a flag in
the chip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The kerneldoc for irq_set_irq_wake() says:
Enable/disable power management wakeup mode, which is
disabled by default.
regmap_irq_set_wake() clears bits to enable wake for an interrupt,
and sets bits to disable wake. Hence, we should set all bits in
wake_buf initially, to mirror the expected disabled state.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regmap-irq chip has no wake base:
* There's no point calling .irq_set_wake, hence IRQCHIP_SKIP_SET_WAKE.
* If some IRQs in the chip are enabled for wake and some aren't, we
should mask those interrupts that are not wake enabled, so that if
they occur during suspend, the system is not awoken. Hence,
IRQCHIP_MASK_ON_SUSPEND.
Note that IRQCHIP_MASK_ON_SUSPEND is handled by check_wakeup_irqs(),
which always iterates over every single interrupt in the system,
irrespective of whether an interrupt is a child of a controller whose
output interrupt has no wake-enabled inputs and hence is presumably
masked itself. Hence this change might cause interrupt unnecessary
masking operations and associated register I/O.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is intended to give each irq_chip a useful name, rather than hard-
coding them all as "regmap".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow later patches to adjust portions of the irq_chip
individually for each regmap_irq_chip that is created.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't write the full register, it's possible there's bits other than the
masks in the same register which we shouldn't be changing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
A number of places in the code were printing error messages that included
the address of a register, but were not calculating the register address
in the same way as the access to the register. Use a temporary to solve
this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When bus->fast_io is set, the locking here is done with spinlocks.
This is currently true for the regmap-mmio bus implementation.
While holding a spinlock we can't go to sleep, various operations
like removing the debugfs entries or re-initializing the cache will
sleep, therefore, shift the locking up to the user.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull second vfs pile from Al Viro:
"The stuff in there: fsfreeze deadlock fixes by Jan (essentially, the
deadlock reproduced by xfstests 068), symlink and hardlink restriction
patches, plus assorted cleanups and fixes.
Note that another fsfreeze deadlock (emergency thaw one) is *not*
dealt with - the series by Fernando conflicts a lot with Jan's, breaks
userland ABI (FIFREEZE semantics gets changed) and trades the deadlock
for massive vfsmount leak; this is going to be handled next cycle.
There probably will be another pull request, but that stuff won't be
in it."
Fix up trivial conflicts due to unrelated changes next to each other in
drivers/{staging/gdm72xx/usb_boot.c, usb/gadget/storage_common.c}
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
delousing target_core_file a bit
Documentation: Correct s_umount state for freeze_fs/unfreeze_fs
fs: Remove old freezing mechanism
ext2: Implement freezing
btrfs: Convert to new freezing mechanism
nilfs2: Convert to new freezing mechanism
ntfs: Convert to new freezing mechanism
fuse: Convert to new freezing mechanism
gfs2: Convert to new freezing mechanism
ocfs2: Convert to new freezing mechanism
xfs: Convert to new freezing code
ext4: Convert to new freezing mechanism
fs: Protect write paths by sb_start_write - sb_end_write
fs: Skip atime update on frozen filesystem
fs: Add freezing handling to mnt_want_write() / mnt_drop_write()
fs: Improve filesystem freezing handling
switch the protection of percpu_counter list to spinlock
nfsd: Push mnt_want_write() outside of i_mutex
btrfs: Push mnt_want_write() outside of i_mutex
fat: Push mnt_want_write() outside of i_mutex
...
mm/page_alloc.c has some memory isolation functions but they are used only
when we enable CONFIG_{CMA|MEMORY_HOTPLUG|MEMORY_FAILURE}. So let's make
it configurable by new CONFIG_MEMORY_ISOLATION so that it can reduce
binary size and we can check it simple by CONFIG_MEMORY_ISOLATION, not if
defined CONFIG_{CMA|MEMORY_HOTPLUG|MEMORY_FAILURE}.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull DMA-mapping updates from Marek Szyprowski:
"Those patches are continuation of my earlier work.
They contains extensions to DMA-mapping framework to remove limitation
of the current ARM implementation (like limited total size of DMA
coherent/write combine buffers), improve performance of buffer sharing
between devices (attributes to skip cpu cache operations or creation
of additional kernel mapping for some specific use cases) as well as
some unification of the common code for dma_mmap_attrs() and
dma_mmap_coherent() functions. All extensions have been implemented
and tested for ARM architecture."
* 'for-linus-for-3.6-rc1' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: add support for DMA_ATTR_SKIP_CPU_SYNC attribute
common: DMA-mapping: add DMA_ATTR_SKIP_CPU_SYNC attribute
ARM: dma-mapping: add support for dma_get_sgtable()
common: dma-mapping: introduce dma_get_sgtable() function
ARM: dma-mapping: add support for DMA_ATTR_NO_KERNEL_MAPPING attribute
common: DMA-mapping: add DMA_ATTR_NO_KERNEL_MAPPING attribute
common: dma-mapping: add support for generic dma_mmap_* calls
ARM: dma-mapping: fix error path for memory allocation failure
ARM: dma-mapping: add more sanity checks in arm_dma_mmap()
ARM: dma-mapping: remove custom consistent dma region
mm: vmalloc: use const void * for caller argument
scatterlist: add sg_alloc_table_from_pages function
This patch adds dma_get_sgtable() function which is required to let
drivers to share the buffers allocated by DMA-mapping subsystem. Right
now the driver gets a dma address of the allocated buffer and the kernel
virtual mapping for it. If it wants to share it with other device (= map
into its dma address space) it usually hacks around kernel virtual
addresses to get pointers to pages or assumes that both devices share
the DMA address space. Both solutions are just hacks for the special
cases, which should be avoided in the final version of buffer sharing.
To solve this issue in a generic way, a new call to DMA mapping has been
introduced - dma_get_sgtable(). It allocates a scatter-list which
describes the allocated buffer and lets the driver(s) to use it with
other device(s) by calling dma_map_sg() on it.
This patch provides a generic implementation based on virt_to_page()
call. Architectures which require more sophisticated translation might
provide their own get_sgtable() methods.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 9adc5374 ('common: dma-mapping: introduce mmap method') added a
generic method for implementing mmap user call to dma_map_ops structure.
This patch converts ARM and PowerPC architectures (the only providers of
dma_mmap_coherent/dma_mmap_writecombine calls) to use this generic
dma_map_ops based call and adds a generic cross architecture
definition for dma_mmap_attrs, dma_mmap_coherent, dma_mmap_writecombine
functions.
The generic mmap virt_to_page-based fallback implementation is provided for
architectures which don't provide their own implementation for mmap method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes now
settled down. All we have here is some extcon driver updates, w1 driver
updates, a few printk cleanups that weren't needed for 3.5, but are good to
have now, and some other minor fixes/changes in the driver core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlARgIUACgkQMUfUDdst+ynDHgCfRNwIB9L+zZvjcKE5e1BhDbUl
wVUAn398DFgbJ1+PjGkd1EMR2uVTh7Ou
=MIFu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg Kroah-Hartman:
"Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes
now settled down. All we have here is some extcon driver updates, w1
driver updates, a few printk cleanups that weren't needed for 3.5, but
are good to have now, and some other minor fixes/changes in the driver
core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
printk: Export struct log size and member offsets through vmcoreinfo
Drivers: hv: Change the hex constant to a decimal constant
driver core: don't trigger uevent after failure
extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device
sysfs: fail dentry revalidation after namespace change fix
sysfs: fail dentry revalidation after namespace change
extcon: spelling of detach in function doc
extcon: arizona: Stop microphone detection if we give up on it
extcon: arizona: Update cable reporting calls and split headset
PM / Runtime: Do not increment device usage counts before probing
kmsg - do not flush partial lines when the console is busy
kmsg - export "continuation record" flag to /dev/kmsg
kmsg - avoid warning for CONFIG_PRINTK=n compilations
kmsg - properly print over-long continuation lines
driver-core: Use kobj_to_dev instead of re-implementing it
driver-core: Move kobj_to_dev from genhd.h to device.h
driver core: Move deferred devices to the end of dpm_list before probing
driver core: move uevent call to driver_register
driver core: fix shutdown races with probe/remove(v3)
Extcon: Arizona: Add driver for Wolfson Arizona class devices
...
The most important feature of this patch set is the new async infrastructure
that makes sure async_synchronize_full() synchronizes all domains and allows
us to remove all the hacks (like having scsi_complete_async_scans() in the
device base code) and means that the async infrastructure will "just work" in
future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
/uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
=y2sh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
Pull the big VFS changes from Al Viro:
"This one is *big* and changes quite a few things around VFS. What's in there:
- the first of two really major architecture changes - death to open
intents.
The former is finally there; it was very long in making, but with
Miklos getting through really hard and messy final push in
fs/namei.c, we finally have it. Unlike his variant, this one
doesn't introduce struct opendata; what we have instead is
->atomic_open() taking preallocated struct file * and passing
everything via its fields.
Instead of returning struct file *, it returns -E... on error, 0
on success and 1 in "deal with it yourself" case (e.g. symlink
found on server, etc.).
See comments before fs/namei.c:atomic_open(). That made a lot of
goodies finally possible and quite a few are in that pile:
->lookup(), ->d_revalidate() and ->create() do not get struct
nameidata * anymore; ->lookup() and ->d_revalidate() get lookup
flags instead, ->create() gets "do we want it exclusive" flag.
With the introduction of new helper (kern_path_locked()) we are rid
of all struct nameidata instances outside of fs/namei.c; it's still
visible in namei.h, but not for long. Come the next cycle,
declaration will move either to fs/internal.h or to fs/namei.c
itself. [me, miklos, hch]
- The second major change: behaviour of final fput(). Now we have
__fput() done without any locks held by caller *and* not from deep
in call stack.
That obviously lifts a lot of constraints on the locking in there.
Moreover, it's legal now to call fput() from atomic contexts (which
has immediately simplified life for aio.c). We also don't need
anti-recursion logics in __scm_destroy() anymore.
There is a price, though - the damn thing has become partially
asynchronous. For fput() from normal process we are guaranteed
that pending __fput() will be done before the caller returns to
userland, exits or gets stopped for ptrace.
For kernel threads and atomic contexts it's done via
schedule_work(), so theoretically we might need a way to make sure
it's finished; so far only one such place had been found, but there
might be more.
There's flush_delayed_fput() (do all pending __fput()) and there's
__fput_sync() (fput() analog doing __fput() immediately). I hope
we won't need them often; see warnings in fs/file_table.c for
details. [me, based on task_work series from Oleg merged last
cycle]
- sync series from Jan
- large part of "death to sync_supers()" work from Artem; the only
bits missing here are exofs and ext4 ones. As far as I understand,
those are going via the exofs and ext4 trees resp.; once they are
in, we can put ->write_super() to the rest, along with the thread
calling it.
- preparatory bits from unionmount series (from dhowells).
- assorted cleanups and fixes all over the place, as usual.
This is not the last pile for this cycle; there's at least jlayton's
ESTALE work and fsfreeze series (the latter - in dire need of fixes,
so I'm not sure it'll make the cut this cycle). I'll probably throw
symlink/hardlink restrictions stuff from Kees into the next pile, too.
Plus there's a lot of misc patches I hadn't thrown into that one -
it's large enough as it is..."
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (127 commits)
ext4: switch EXT4_IOC_RESIZE_FS to mnt_want_write_file()
btrfs: switch btrfs_ioctl_balance() to mnt_want_write_file()
switch dentry_open() to struct path, make it grab references itself
spufs: shift dget/mntget towards dentry_open()
zoran: don't bother with struct file * in zoran_map
ecryptfs: don't reinvent the wheels, please - use struct completion
don't expose I_NEW inodes via dentry->d_inode
tidy up namei.c a bit
unobfuscate follow_up() a bit
ext3: pass custom EOF to generic_file_llseek_size()
ext4: use core vfs llseek code for dir seeks
vfs: allow custom EOF in generic_file_llseek code
vfs: Avoid unnecessary WB_SYNC_NONE writeback during sys_sync and reorder sync passes
vfs: Remove unnecessary flushing of block devices
vfs: Make sys_sync writeout also block device inodes
vfs: Create function for iterating over block devices
vfs: Reorder operations during sys_sync
quota: Move quota syncing to ->sync_fs method
quota: Split dquot_quota_sync() to writeback and cache flushing part
vfs: Move noop_backing_dev_info check from sync into writeback
...
* ACPI conversion to PM handling based on struct dev_pm_ops.
* Conversion of a number of platform drivers to PM handling based on struct
dev_pm_ops and removal of empty legacy PM callbacks from a couple of PCI
drivers.
* Suspend-to-both for in-kernel hibernation from Bojan Smojver.
* cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti U Murthy.
* cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
* Suspend and hibernate fixes from Srivatsa S. Bhat and Colin Cross.
* Generic PM domains framework updates.
* RTC CMOS wakeup signaling update from Paul Fox.
* sparse warnings fixes from Sachin Kamat.
* Build warnings fixes for the generic PM domains framework and PM sysfs code.
* sysfs switch for printing device suspend times from Sameer Nanda.
* Documentation fix from Oskar Schirmer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=vC4/
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
- ACPI conversion to PM handling based on struct dev_pm_ops.
- Conversion of a number of platform drivers to PM handling based on
struct dev_pm_ops and removal of empty legacy PM callbacks from a
couple of PCI drivers.
- Suspend-to-both for in-kernel hibernation from Bojan Smojver.
- cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti
Murthy.
- cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
- Suspend and hibernate fixes from Srivatsa Bhat and Colin Cross.
- Generic PM domains framework updates.
- RTC CMOS wakeup signaling update from Paul Fox.
- sparse warnings fixes from Sachin Kamat.
- Build warnings fixes for the generic PM domains framework and PM
sysfs code.
- sysfs switch for printing device suspend times from Sameer Nanda.
- Documentation fix from Oskar Schirmer.
* tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (70 commits)
cpufreq: Fix sysfs deadlock with concurrent hotplug/frequency switch
EXYNOS: bugfix on retrieving old_index from freqs.old
PM / Sleep: call early resume handlers when suspend_noirq fails
PM / QoS: Use NULL pointer instead of plain integer in qos.c
PM / QoS: Use NULL pointer instead of plain integer in pm_qos.h
PM / Sleep: Require CAP_BLOCK_SUSPEND to use wake_lock/wake_unlock
PM / Sleep: Add missing static storage class specifiers in main.c
cpuilde / ACPI: remove time from acpi_processor_cx structure
cpuidle / ACPI: remove usage from acpi_processor_cx structure
cpuidle / ACPI : remove latency_ticks from acpi_processor_cx structure
rtc-cmos: report wakeups from interrupt handler
PM / Sleep: Fix build warning in sysfs.c for CONFIG_PM_SLEEP unset
PM / Domains: Fix build warning for CONFIG_PM_RUNTIME unset
olpc-xo15-sci: Use struct dev_pm_ops for power management
PM / Domains: Replace plain integer with NULL pointer in domain.c file
PM / Domains: Add missing static storage class specifier in domain.c file
PM / crypto / ux500: Use struct dev_pm_ops for power management
PM / IPMI: Remove empty legacy PCI PM callbacks
tpm_nsc: Use struct dev_pm_ops for power management
tpm_tis: Use struct dev_pm_ops for power management
...
A few fixes plus a few features, the most generally useful thing being
the register paging support which can be used by quite a few devices:
- Support for wake IRQs in regmap-irq
- Support for register paging
- Support for explicitly specified endianness, mostly for MMIO.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=uSSe
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A few fixes plus a few features, the most generally useful thing being
the register paging support which can be used by quite a few devices:
- Support for wake IRQs in regmap-irq
- Support for register paging
- Support for explicitly specified endianness, mostly for MMIO."
* tag 'regmap-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix incorrect arguments to kzalloc() call
regmap: Add hook for printk logging for debugging during early init
regmap: Fix work_buf switching for page update during virtual range access.
regmap: Add support for register indirect addressing.
regmap: Move lock out from internal function _regmap_update_bits().
regmap: mmio: Staticize regmap_mmio_gen_context()
regmap: Remove warning on stubbed dev_get_regmap()
regmap: Implement support for wake IRQs
regmap: Don't try to map non-existant IRQs
regmap: Constify regmap_irq_chip
regmap: mmio: request native endian formatting
regmap: allow busses to request formatting with specific endianness
Now that scsi registers its async scan work with the async subsystem,
wait_for_device_probe() is sufficient for ensuring all scanning is
complete.
[jejb: fix merge problems with eea03c20ae Make wait_for_device_probe() also do scsi_complete_async_scans()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit cf579dfb82 (PM / Sleep: Introduce
"late suspend" and "early resume" of devices) introduced a bug where
suspend_late handlers would be called, but if dpm_suspend_noirq returned
an error the early_resume handlers would never be called. All devices
would end up on the dpm_late_early_list, and would never be resumed
again.
Fix it by calling dpm_resume_early when dpm_suspend_noirq returns
an error.
Signed-off-by: Colin Cross <ccross@android.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit a7a20d1039 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d01 ("fix async probe
regression"), so that same commit a7a20d1039 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: linux-scsi <linux-scsi@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pm-sleep:
PM / Sleep: Require CAP_BLOCK_SUSPEND to use wake_lock/wake_unlock
PM / Sleep: Add missing static storage class specifiers in main.c
PM / Sleep: Fix build warning in sysfs.c for CONFIG_PM_SLEEP unset
PM / Hibernate: Print hibernation/thaw progress indicator one line at a time.
PM / Sleep: Separate printing suspend times from initcall_debug
PM / Sleep: add knob for printing device resume times
ftrace: Disable function tracing during suspend/resume and hibernation, again
PM / Hibernate: Enable suspend to both for in-kernel hibernation.
* pm-domains:
PM / Domains: Fix build warning for CONFIG_PM_RUNTIME unset
PM / Domains: Replace plain integer with NULL pointer in domain.c file
PM / Domains: Add missing static storage class specifier in domain.c file
PM / Domains: Allow device callbacks to be added at any time
PM / Domains: Add device domain data reference counter
PM / Domains: Add preliminary support for cpuidle, v2
PM / Domains: Do not stop devices after restoring their states
PM / Domains: Use subsystem runtime suspend/resume callbacks by default
Fix the following sparse warning:
drivers/base/power/qos.c:465:29: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix the following sparse warnings:
drivers/base/power/main.c:48:1: warning: symbol 'dpm_prepared_list' was not declared. Should it be static?
drivers/base/power/main.c:49:1: warning: symbol 'dpm_suspended_list' was not declared. Should it be static?
drivers/base/power/main.c:50:1: warning: symbol 'dpm_late_early_list' was not declared. Should it be static?
drivers/base/power/main.c:51:1: warning: symbol 'dpm_noirq_list' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Do not send the uevent if driver_add_groups failed.
Reported-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime_get_noresume() calls before really_probe() and
before executing __device_attach() for each driver on the
device's bus cause problems to happen if probing fails and if the
driver has enabled runtime PM for the device in its .probe()
callback. Namely, in that case, if the device has been resumed
by the driver after enabling its runtime PM and if it turns out that
.probe() should return an error, the driver is supposed to suspend
the device and disable its runtime PM before exiting .probe().
However, because the device's runtime PM usage counter was
incremented by the core before calling .probe(), the driver's attempt
to suspend the device will not succeed and the device will remain in
the full-power state after the failing .probe() has returned.
To fix this issue, remove the pm_runtime_get_noresume() calls from
driver_probe_device() and from device_attach() and replace the
corresponding pm_runtime_put_sync() calls with pm_runtime_idle()
to preserve the existing behavior (which is to check if the device
is idle and to suspend it eventually in that case after probing).
Reported-and-tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When deferred probe was originally added the idea was that devices which
defer their probes would move themselves to the end of dpm_list in order
to try to keep the assumptions that we're making about the list being in
roughly the order things should be suspended correct. However this hasn't
been what's been happening and doing it requires a lot of duplicated code
to do the moves.
Instead take a simple, brute force solution and have the deferred probe
code push devices to the end of dpm_list before it retries the probe. This
does mean we lock the dpm_list a bit more often but it's very simple and
the code shouldn't be a fast path. We do the move with the deferred mutex
dropped since doing things with fewer locks held simultaneously seems like
a good idea.
This approach was most recently suggested by Grant Likely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Grant Likely <grant.likely@secretlab.ca>,
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device driver attribute groups are created after userspace is notified
via an add event. Fix this by moving the kobject_uevent call to
driver_register after the attribute groups are added.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly, .shutdown callback may touch a uninitialized hardware
if dev->driver is set and .probe is not completed.
Secondly, device_shutdown() may dereference a null pointer to cause
oops when dev->driver is cleared after it has been checked in
device_shutdown().
So just hold device lock and its parent lock(if it has) to
fix the races.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
all callers want the same thing, actually - a kinda-sorta analog of
kern_path_create(). I.e. they want parent vfsmount/dentry (with
->i_mutex held, to make sure the child dentry is still their child)
+ the child dentry.
Signed-off-by Al Viro <viro@zeniv.linux.org.uk>
The power/async device sysfs attribute is only used if both
CONFIG_PM_ADVANCED_DEBUG and CONFIG_PM_SLEEP are set, but the code
implementing it doesn't depend on CONFIG_PM_SLEEP. As a result, a
build warning appears if CONFIG_PM_ADVANCED_DEBUG is set and
CONFIG_PM_SLEEP is not set.
Fix it by adding a #ifdef CONFIG_PM_SLEEP around the code in
question.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The functions genpd_save_dev() and genpd_restore_dev() are not used
for CONFIG_PM_RUNTIME unset, so move them under an appropriate
#ifdef.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fixes the following sparse warning:
drivers/base/power/domain.c:1679:55: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fixes the folloiwng sparse warning:
drivers/base/power/domain.c:149:5:
warning: symbol '__pm_genpd_poweron' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
On certain bios, resume hangs if cpus are allowed to enter idle states
during suspend [1].
This was fixed in apci idle driver [2].But intel_idle driver does not
have this fix. Thus instead of replicating the fix in both the idle
drivers, or in more platform specific idle drivers if needed, the
more general cpuidle infrastructure could handle this.
A suspend callback in cpuidle_driver could handle this fix. But
a cpuidle_driver provides only basic functionalities like platform idle
state detection capability and mechanisms to support entry and exit
into CPU idle states. All other cpuidle functions are found in the
cpuidle generic infrastructure for good reason that all cpuidle
drivers, irrepective of their platforms will support these functions.
One option therefore would be to register a suspend callback in cpuidle
which handles this fix. This could be called through a PM_SUSPEND_PREPARE
notifier. But this is too generic a notfier for a driver to handle.
Also, ideally the job of cpuidle is not to handle side effects of suspend.
It should expose the interfaces which "handle cpuidle 'during' suspend"
or any other operation, which the subsystems call during that respective
operation.
The fix demands that during suspend, no cpus should be allowed to enter
deep C-states. The interface cpuidle_uninstall_idle_handler() in cpuidle
ensures that. Not just that it also kicks all the cpus which are already
in idle out of their idle states which was being done during cpu hotplug
through a CPU_DYING_FROZEN callbacks.
Now the question arises about when during suspend should
cpuidle_uninstall_idle_handler() be called. Since we are dealing with
drivers it seems best to call this function during dpm_suspend().
Delaying the call till dpm_suspend_noirq() does no harm, as long as it is
before cpu_hotplug_begin() to avoid race conditions with cpu hotpulg
operations. In dpm_suspend_noirq(), it would be wise to place this call
before suspend_device_irqs() to avoid ugly interactions with the same.
Ananlogously, during resume.
References:
[1] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/674075.
[2] http://marc.info/?l=linux-pm&m=133958534231884&w=2
Reported-and-tested-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Sometimes for failures during very early init the trace infrastructure
isn't available early enough to be used. For this sort of problem
defining LOG_DEVICE will add printks for basic register I/O on a specific
device, allowing trace to be extracted when the trace system doesn't come
up early enough to work with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make it possible to modify device callbacks used by the generic PM
domains core code at any time, not only after the device has been
added to a domain. This will allow device drivers to provide their
own device PM domain callbacks even if they are registered before
adding the devices to PM domains.
For this purpose, use the observation that the struct
generic_pm_domain_data object containing the relevant callback
pointers may be allocated by pm_genpd_add_callbacks() and the
callbacks may be set before __pm_genpd_add_device() is run for
the given device. This object will then be used by
__pm_genpd_add_device(), but it has to be protected from
premature removal by reference counting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a mechanism for counting references to the
struct generic_pm_domain_data object pointed to by
dev->power.subsys_data->domain_data if the device in question
belongs to a generic PM domain.
This change is necessary for a subsequent patch making it possible to
allocate that object from within pm_genpd_add_callbacks(), so that
drivers can attach their PM domain device callbacks to devices before
those devices are added to PM domains.
This patch has been tested on the SH7372 Mackerel board.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This picks up the big printk fixes, and resolves a merge issue with:
drivers/extcon/extcon_gpio.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems there are CPU cores located in the same power
domains as I/O devices. Then, power can only be removed from the
domain if all I/O devices in it are not in use and the CPU core
is idle. Add preliminary support for that to the generic PM domains
framework.
First, the platform is expected to provide a cpuidle driver with one
extra state designated for use with the generic PM domains code.
This state should be initially disabled and its exit_latency value
should be set to whatever time is needed to bring up the CPU core
itself after restoring power to it, not including the domain's
power on latency. Its .enter() callback should point to a procedure
that will remove power from the domain containing the CPU core at
the end of the CPU power transition.
The remaining characteristics of the extra cpuidle state, referred to
as the "domain" cpuidle state below, (e.g. power usage, target
residency) should be populated in accordance with the properties of
the hardware.
Next, the platform should execute genpd_attach_cpuidle() on the PM
domain containing the CPU core. That will cause the generic PM
domains framework to treat that domain in a special way such that:
* When all devices in the domain have been suspended and it is about
to be turned off, the states of the devices will be saved, but
power will not be removed from the domain. Instead, the "domain"
cpuidle state will be enabled so that power can be removed from
the domain when the CPU core is idle and the state has been chosen
as the target by the cpuidle governor.
* When the first I/O device in the domain is resumed and
__pm_genpd_poweron(() is called for the first time after
power has been removed from the domain, the "domain" cpuidle
state will be disabled to avoid subsequent surprise power removals
via cpuidle.
The effective exit_latency value of the "domain" cpuidle state
depends on the time needed to bring up the CPU core itself after
restoring power to it as well as on the power on latency of the
domain containing the CPU core. Thus the "domain" cpuidle state's
exit_latency has to be recomputed every time the domain's power on
latency is updated, which may happen every time power is restored
to the domain, if the measured power on latency is greater than
the latency stored in the corresponding generic_pm_domain structure.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
While resuming a device belonging to a PM domain,
pm_genpd_runtime_resume() calls __pm_genpd_restore_device() to
restore its state, if necessary. The latter starts the device,
using genpd_start_dev(), restores its state, using
genpd_restore_dev(), and then stops it, using genpd_stop_dev().
However, this last operation is not necessary, because the
device is supposed to be operational after pm_genpd_runtime_resume()
has returned and because of it pm_genpd_runtime_resume() has to
call genpd_start_dev() once again for the "restored" device, which
is inefficient.
To make things more efficient, remove the call to genpd_stop_dev()
from __pm_genpd_restore_device() and the direct call to
genpd_start_dev() from pm_genpd_runtime_resume(). [Of course,
genpd_start_dev() still has to be called by it for devices with the
power.irq_safe flag set, because __pm_genpd_restore_device() is not
executed for them.]
This change has been tested on the SH7372 Mackerel board.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, the default "save state" and "restore state" routines
for generic PM domains, pm_genpd_default_save_state() and
pm_genpd_default_restore_state(), respectively, only use runtime PM
callbacks provided by device drivers, but in general those callbacks
need not provide the entire necessary functionality. Namely, in
general it may be necessary to execute subsystem (i.e. device type,
device class or bus type) callbacks that will carry out all of the
necessary operations.
For this reason, modify pm_genpd_default_save_state() and
pm_genpd_default_restore_state() to execute subsystem callbacks,
if they are provided, and fall back to driver callbacks otherwise.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the behavior of the newly introduced
/sys/power/pm_print_times attribute so that its initial value
depends on initcall_debug, but setting it to 0 will cause device
suspend/resume times not to be printed, even if initcall_debug has
been set. This way, the people who use initcall_debug for reasons
other than PM debugging will be able to switch the suspend/resume
times printing off, if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a new knob called /sys/power/pm_print_times. Setting it to 1
enables printing of time taken by devices to suspend and resume.
Setting it to 0 disables this printing (unless overridden by
initcall_debug kernel command line option).
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
__device_suspend() must always send a completion. Otherwise, parent
devices will wait forever.
Commit 1e2ef05b, "PM: Limit race conditions between runtime PM and
system sleep (v2)", introduced a regression by short-circuiting the
complete_all() for certain error cases.
This patch fixes the bug by always signalling a completion.
Addresses http://crosbug.com/31972
Tested by injecting an abort.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNQcACgkQMUfUDdst+yklTQCfZCXFlhA43bZo/8Joqd2pLIIW
2uoAoMze0SlfJeN6Qu7yY0P+qV/f/pc3
=UNFY
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and printk fixes from Greg Kroah-Hartman:
"Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: max8997: Add missing kfree for info->edev in max8997_muic_remove()
extcon: Set platform drvdata in gpio_extcon_probe() and fix irq leak
extcon: Fix wrong index in max8997_extcon_cable[]
kmsg - kmsg_dump() fix CONFIG_PRINTK=n compilation
printk: return -EINVAL if the message len is bigger than the buf size
printk: use mutex lock to stop syslog_seq from going wild
kmsg - kmsg_dump() use iterator to receive log buffer content
vme: change maintainer e-mail address
Extcon: Don't try to create duplicate link names
driver core: fixup reversed deferred probe order
printk: Fix alignment of buf causing crash on ARM EABI
Tools: hv: verify origin of netlink connector message
After page update, orginal work_buf has to be restored regardless of
the result.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Devices with register paging or indirectly accessed registers can configure
register mapping to map those on virtual address range. During access to
virtually mapped register range, indirect addressing is processed
automatically, in following steps:
1. selector for page or indirect register is updated (when needed);
2. register in data window is accessed.
Configuration should provide minimum and maximum register for virtual range,
details of selector field for page selection, minimum and maximum register of
data window for indirect access.
Virtual range registers are managed by cache as well as direct access
registers. In order to make indirect access more efficient, selector register
should be declared as non-volatile, if possible.
struct regmap_config is extended with the following:
struct regmap_range_cfg *ranges;
unsigned int n_ranges;
[Also reordered debugfs init to later on since the cleanup code was
conflicting with the new cleanup code for ranges anyway -- broonie]
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Locks are moved to regmap_update_bits(), which allows to reenter internal
function _regmap_update_bits() from inside of regmap read/write routines.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix kernel-doc warnings in drivers/base/dma*.c:
Warning(drivers/base/dma-buf.c:498): No description found for parameter 'vaddr'
Warning(drivers/base/dma-coherent.c:199): No description found for parameter 'ret'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) drvdata is for a driver to store a pointer to driver specific data
2) If no driver is bound, there is no driver specific data associated with
the device
3) Thus logically drvdata should be NULL if no driver is bound.
But many drivers don't clear drvdata on device_release, or set drvdata
early on in probe and leave it set on probe error. Both of which results
in a dangling pointer in drvdata.
This patch enforce for drvdata to be NULL after device_release or on probe
failure.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If driver requests probe deferral,
it will be added to deferred_probe_pending_list
by driver_deferred_probe_add(), but, it used list_add().
Because of that, deferred probe will be run as reversed order.
This patch uses list_add_tail(), and solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regmap_mmio_gen_context() is only used in regmap-mmio.c. Thus make it static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Wolfram Sang