MC13783 can be programmed to wait some clock cycles between the
touchscreen polarization and the resistance conversion. This is
needed to adjust for touchscreens with high capacitance between
plates.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implement suspend and resume methods to set up devices as wakeup source.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This fixes reference-before-check problem; there is no reason to check
if caller passed NULL dev or bus_ops as it is done only by bus-specific
drivers which already do the right thing.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Data Modul TP 72037 EasyTouch controller is derived from EGALAX
controller and is capable of detecting dual contacts. Packets can be 5
bytes or 10 bytes long, depending whether one or two contacts are
detected. Format is same as EGALAX touch controller, but with x and y
coordinates inverted.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for TI's touchscreen
controller for a 4/5/8 wire resistive panel
that is directly fed to the ADC.
This touchscreen controller will be part of
AM335x TI SoC. The TRM can be found at:
http://www.ti.com/lit/ug/spruh73a/spruh73a.pdf
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The main purpose of this patch is to fix several section mismatch
warnings from the board file and a few board specific drivers,
introduced with recent Amstrad Delta patch series, some of them rising
up only when building with CONFIG_MODULES not set.
While being at it, section tagging of all init data found in the board
file have been revised and hopefully corrected and/or optimized.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Thaw and poweroff routines are missing for spear-keyboard. They are
required for:
- Error case scenarios during freeze
- Using test features, of hibernate.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Let platform pass mode information to keyboard driver according to which
it configures itself. The mode can be
- KEYPAD_9x9 0
- KEYPAD_6x6 1
- KEYPAD_2x2 2
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make use of psmouse_activate() and psmouse_deactivate() from psmouse-base.c
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Other drivers duplicate this code; no sense in having it be private
to psmouse-base.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On m68k:
drivers/input/misc/twl4030-vibra.c:175:5: warning: "CONFIG_PM" is not
defined
We should use #ifdef instead of #if and also check CONFIG_PM_SLEEP
instead of CONFIG_PM.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 509f87c5f5 (evdev - do not block waiting for an event if fd
is nonblock) created a code path were it was possible to use retval
uninitialized.
This could lead to the xorg evdev input driver getting corrupt data
and refusing to work with log messages like
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
(for drivers auo-pixcir-ts and gpio-keys).
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ALPS touchpad detection fails if some buttons of ALPS are pressed.
The reason is that the "E6" query response byte is different from
what is expected.
This was tested on a Toshiba Portege R500.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enable the input system to be used with a compat ABI with 64-bit time.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To simplify detection as a touchpad, inform userspace of the physical
properties of the device.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
[rydberg@euromail.se: conflict resolution]
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Add platform hooks to be called when individual sa1111 devices are
enabled and disabled. This will allow us to move some platform
specifics out of the individual drivers.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a .owner initializer to the sa1111 driver structures to allow
allow the modules to be associated with their driver structures.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the ability to extract MT slot data via a new ioctl,
EVIOCGMTSLOTS. The function returns an array of slot values for the
specified ABS_MT event type.
Example of user space usage:
struct { unsigned code; int values[64]; } req;
req.code = ABS_MT_POSITION_X;
if (ioctl(fd, EVIOCGMTSLOTS(sizeof(req)), &req) < 0)
return -1;
for (i = 0; i < 64; i++)
printf("slot %d: %d\n", i, req.values[i]);
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Allow marking some of GPIO pins as ignored to to avoid continuously
generating KBC input events.
Signed-off-by: Shridhar Rasal <srasal@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a driver for Synaptics USB touchpad or pointing stick
devices. These USB devices emulate an USB mouse by default, so one can
also use the usbhid driver. However, in combination with special user
space drivers this kernel driver allows one to customize the behaviour
of the device.
An extended version of this driver with support for the cPad background
display can be found at
<http://jan-steinhoff.de/linux/synaptics-usb.html>.
Signed-off-by: Jan Steinhoff <mail@jan-steinhoff.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As noted by Arve and others, since wall time can jump backwards, it is
difficult to use for input because one cannot determine if one event
occurred before another or for how long a key was pressed.
However, the timestamp field is part of the kernel ABI, and cannot be
changed without possibly breaking existing users.
This patch adds a new IOCTL that allows a clockid to be set in the
evdev_client struct that will specify which time base to use for event
timestamps (ie: CLOCK_MONOTONIC instead of CLOCK_REALTIME).
For now we only support CLOCK_MONOTONIC and CLOCK_REALTIME, but
in the future we could support other clockids if appropriate.
The default remains CLOCK_REALTIME, so we don't change the ABI.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
From 2d5a38a56453421e82428155f4b00303f3fb19b2 Mon Sep 17 00:00:00 2001
From: Igor Murzov <e-mail@date.by>
Date: Wed, 1 Feb 2012 03:11:53 +0400
Subject: [PATCH] Input: i8042 - add Lenovo Ideapad U455 to 'reset' blacklist
Lenovo Ideapad U455 needs to be in the reset quirk list for its
touchpad's proper function.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=40672
Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The current MT accessor function does not distinguish between the MT
values and the slot specification event. Add an accessor function for
the values only, and use it where appropriate.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
serio_raw_read now returns (sometimes partially) successful number of
bytes transferred to the caller, and only returns error code to the
caller on completely failed transfers.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 509f87c5f5 (evdev - do not block waiting for an event if fd
is nonblock) created a code path were it was possible to use retval
uninitialized.
This could lead to the xorg evdev input driver getting corrupt data
and refusing to work with log messages like
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
(for drivers auo-pixcir-ts and gpio-keys).
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cypress TrueTouch(tm) Standard Product controllers are found in
a wide range of embedded devices. This driver add support for a
variety of TTSP controllers.
Since the hardware is capable of tracking identifiable contacts, multi-touch
protocol type B (stateful) is used to report contact information.
The driver is composed of a core driver that process the data sent by
the contacts and a set of bus specific interface modules. This patch
adds the base core TTSP driver.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
And add two new data formats.
Tested-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As part of the removal of get_driver()/put_driver(), this patch
(as1510) changes driver_find(); it now drops the reference it acquires
before returning. The patch also adjusts all the callers of
driver_find() to remove the now unnecessary calls to put_driver().
In addition, the patch adds a warning to driver_find(): Callers must
make sure the driver they are searching for does not get unloaded
while they are using it. This has always been the case; driver_find()
has never prevented a driver from being unregistered or unloaded.
Hence the patch will not introduce any new bugs. The existing callers
all seem to be okay in this respect, however I don't understand the
video drivers well enough to be certain about them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Kyungmin Park <kyungmin.park@samsung.com>
CC: Andy Walls <awalls@md.metrocast.net>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enable keypress interrupt to support wakeup from low power state.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We don't actually care if the device has been runtime suspended immediately
so we can just drop the reference without waiting for any state change to
be implemented. This may allow us to avoid some suspend/resume cycles and
is a bit more friendly to the rest of the system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Convert the driver to standard spilt model arch-specific code registers
platform device to which driver code can bind later.
Also request IRQ immediately upon binding to the device instead of doing
this when serio port is being opened.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Convert driver to use dev_pm_ops instead of legacy PM infrastructure.
Also make 'open' a bool since it is really a boolean.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also proper guard for system suspend/resume methods is CONFIG_PM_SLEEP,
not CONFIG_PM.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Because we are using platform_device_probe() to register the driver
we do not need to assign driver's probe method. We also can mark
ske_keypad_probe(), together with ske_keypad_chip_init(), as __init
instead of __devinit.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HHrh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: bcm5974 - set BUTTONPAD property
Input: serio_raw - return proper result when serio_raw_write fails
Input: serio_raw - really signal HUP upon disconnect
Input: serio_raw - remove stray semicolon
Input: revert some over-zealous conversions to module_platform_driver()
Some bcm5974 trackpads have a physical button beneath the physical surface.
This patch sets the property bit so user space applications can detect the
trackpad type and act accordingly.
Signed-off-by: Jussi Pakkanen <jussi.pakkanen@canonical.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If serio_raw_write was always returning number of bytes successfully
sent to serio port and never signalled error condition to the caller.
Change it so that for completely failed transfers appropriate error
code returned to the caller (partially successful writes still return
number of bytes transferred).
Reported-by: Che-liang Chiou <clchiou@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 8c1c10d570 attempted to signal
POLLHUP | POLLERR condition when polling disconnected device,
unfortunately it did not do it quite correctly.
Reported-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Recent conversion to module_platform_driver() went a bit too far and
converted not only drivers that used platform_driver_register() but
also ones using platform_driver_probe(), breaking them in process.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Wire-up new system calls
microblaze: Remove NO_IRQ from architecture
input: xilinx_ps2: Don't use NO_IRQ
block: xsysace: Don't use NO_IRQ
microblaze: Trivial asm fix
microblaze: Fix debug message in module
microblaze: Remove eprintk macro
microblaze: Send CR before LF for early console
microblaze: Change NO_IRQ to 0
microblaze: Use irq_of_parse_and_map for timer
microblaze: intc: Change variable name
microblaze: Use of_find_compatible_node for timer and intc
microblaze: Add __cmpdi2
microblaze: Synchronize __pa __va macros
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
* 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (37 commits)
xen/pciback: Expand the warning message to include domain id.
xen/pciback: Fix "device has been assigned to X domain!" warning
xen/pciback: Move the PCI_DEV_FLAGS_ASSIGNED ops to the "[un|]bind"
xen/xenbus: don't reimplement kvasprintf via a fixed size buffer
xenbus: maximum buffer size is XENSTORE_PAYLOAD_MAX
xen/xenbus: Reject replies with payload > XENSTORE_PAYLOAD_MAX.
Xen: consolidate and simplify struct xenbus_driver instantiation
xen-gntalloc: introduce missing kfree
xen/xenbus: Fix compile error - missing header for xen_initial_domain()
xen/netback: Enable netback on HVM guests
xen/grant-table: Support mappings required by blkback
xenbus: Use grant-table wrapper functions
xenbus: Support HVM backends
xen/xenbus-frontend: Fix compile error with randconfig
xen/xenbus-frontend: Make error message more clear
xen/privcmd: Remove unused support for arch specific privcmp mmap
xen: Add xenbus_backend device
xen: Add xenbus device driver
xen: Add privcmd device driver
xen/gntalloc: fix reference counts on multi-page mappings
...
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
This is where the really nasty conflicts in the samsung platform
start, due to some files getting moved around and combined in the
'restart' branch that has already gone into mainline through
Russell's tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XY2N
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
Conflicts:
arch/arm/mach-exynos/Makefile
arch/arm/mach-exynos/cpu.c -> common.c
arch/arm/mach-exynos/include/mach/entry-macro.S
arch/arm/mach-exynos/init.c -> common.c
arch/arm/mach-s5p64x0/init.c -> common.c
arch/arm/mach-s5pv210/init.c -> common.c
Multiple files were moved into common.c files in the rmk/for-linus
branch, so this moves over the samsung/dt changes to the new
files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers shouldn't use NO_IRQ. Microblaze and PPC
define NO_IRQ as 0 and this reference will be removed
in near future.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
CC: Rob Herring <rob.herring@calxeda.com>
Instead of manually create and handler kernel thread switch to threaded
IRQ and let kernel IRQ core manage thread for us.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Let compiler figure out which ones makes most sense to inline.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add __devinit/__devexit sections annotations so parts of code could be
discarded after completing driver initialization.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
So that it has proper symlink to the containing module in sysfs.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of using legacy PM interfaces switch to using dev_pm_ops.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The 'name', 'owner', and 'mod_name' members are redundant with the
identically named fields in the 'driver' sub-structure. Rather than
switching each instance to specify these fields explicitly, introduce
a macro to simplify this.
Eliminate further redundancy by allowing the drvname argument to
DEFINE_XENBUS_DRIVER() to be blank (in which case the first entry from
the ID table will be used for .driver.name).
Also eliminate the questionable xenbus_register_{back,front}end()
wrappers - their sole remaining purpose was the checking of the
'owner' field, proper setting of which shouldn't be an issue anymore
when the macro gets used.
v2: Restore DRV_NAME for the driver name in xen-pciback.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
both callers of device_get_devnode() are only interested in lower 16bits
and nobody tries to return anything wider than 16bit anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Several protocol initialization routines can fail after they set up
psmouse methods, such as reconnect and disconnect. This may lead to
these stale methods used with different protocol that they were
intended to be used for and may cause unpredictavle behavior and/or
crashes.
Make sure we start with a clean slate before executing each and every
protocol detection and/or initialization routine.
Reported-by: Paul Fox <pgf@laptop.org>
Acked-by: Tai-hwa Liang <avatar@sentelic.com>
Acked-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If there is a full packet in the buffer, and we overflow that buffer
right after checking for that condition, it would have been possible
for us to block indefinitely (rather, until the next full packet) even if
the file was marked as O_NONBLOCK.
Cc: Jeff Brown <jeffbrown@android.com>
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Without this, it was possible for the reader to get ahead of packet_head.
If the input device generated a partial packet *right* after the reader
got ahead, then we can get into a situation where the device is marked
readable, but read always returns 0 until the next packet is finished
(i.e a SYN is generated by the input driver).
This situation can also happen if we overflow the buffer while a reader
is trying to read an event out.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When runtime power management is enabled put the Samsung keypad driver
into suspend mode with wakeups disabled whenever the device is open but
a key is not actually been pressed. As well as saving a trivial amount of
power this will support the use of SoC wide idle modes which put the entire
device into a retention mode and use explicit wakeup sources to exit.
Since not all of the interrupt controllers used with the driver support
set_irq_wake() (though they all do the right thing) and there's a nasty
WARN() when we disable wake after failing to enable it keep track of the
current wake status from runtime PM and only disable wake if we managed
to enable it; I'm not entirely sure why this doesn't affect the existing
uses of the API in the driver.
System suspend is unaffected as the driver core will runtime resume any
suspended devices prior to system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Conflicts:
drivers/input/keyboard/samsung-keypad.c
This adds a simple device tree binding to the tegra keyboard controller.
Also, mark the default keymap as __devinitdata since it is not referenced
after boot.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fixing wrong register offset which is used to retrieve the number of buttons
attached to the hardware.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since commit 6384fd "ARM: pxa: rename IRQ_GPIO to PXA_GPIO_TO_IRQ",
I got below buid errors due to implicit declaration of function 'IRQ_GPIO'.
Use common gpio_to_irq() to replace machine dependant macro IRQ_GPIO().
CC drivers/input/touchscreen/zylonite-wm97xx.o
drivers/input/touchscreen/zylonite-wm97xx.c: In function 'zylonite_wm97xx_probe':
drivers/input/touchscreen/zylonite-wm97xx.c:195: error: implicit declaration of function 'IRQ_GPIO'
make[3]: *** [drivers/input/touchscreen/zylonite-wm97xx.o] Error 1
make[2]: *** [drivers/input/touchscreen] Error 2
make[1]: *** [drivers/input] Error 2
make: *** [drivers] Error 2
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some displays from AUO have a so called in-cell touchscreen, meaning it
is built directly into the display unit.
Touchdata is gathered through PIXCIR Tango-ICs and processed in an
Atmel ATmega168P with custom firmware. Communication between the host
system and ATmega is done via I2C.
Devices using this touch solution include the Dell Streak5 and the family
of Qisda ebook readers.
The driver reports single- and multi-touch events including touch area
values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* pm-domains:
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
PM / Domains: Provide an always on power domain governor
PM / Domains: Fix default system suspend/resume operations
PM / Domains: Make it possible to assign names to generic PM domains
PM / Domains: fix compilation failure for CONFIG_PM_GENERIC_DOMAINS unset
PM / Domains: Automatically update overoptimistic latency information
PM / Domains: Add default power off governor function (v4)
PM / Domains: Add device stop governor function (v4)
PM / Domains: Rework system suspend callback routines (v2)
PM / Domains: Introduce "save/restore state" device callbacks
PM / Domains: Make it possible to use per-device domain callbacks
Make the st1232 driver use dev_pm_qos_add_ancestor_request() to
add a device PM QoS latency constraint for the controller it
depends on, so that the controller won't go into an overly deep
low-power state when the touchscreen has to be particularly
responsive (e.g. when the user moves his or her finger on it).
This change is based on a prototype patch from Guennadi Liakhovetski.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This will improve the output of the sensor.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This also changes the devname parameter delivered to
request_threaded_irq() from "mpu_int" to "mpu3050".
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make sure that mutex is released upon register writing failure.
This fixes boot freezing observed on ARM based OLPC
(http://dev.laptop.org/ticket/11357).
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add device tree based discovery support for Samsung's keypad controller.
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Don't use Amstrad Delta custom I/O functions once GPIO interface is
available for the underlying hardware.
While requesting and initializing GPIO pins used, also take care of one
extra pin KEYBRD_DATAOUT which, even if not used by the driver, belongs
to the device and affects its functioning.
Once done, move the driver initialization back to the device_initcall
level, reverting the temporary chane introduced with patch 1/7 "ARM:
OMAP1: ams-delta: register latch dependent devices later". That change
is no longer required once the driver takes care of registering used
GPIO pins, and it's better to initialize the device before others using
the latch2 based GPIO pins, otherwise a garbage is reported on boot,
perhaps due to random data already captured by the FIQ handler while the
keyboard related latch bits are written with random values during
initialization of those other latch2 dependent devices.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[tony@atomide.com: renamed _gpios to ams_delta_gpios]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation to converting Amstrad Delta on-board latches to
basic_mmio_gpio devices, registration of platform devices which depend
on latches and will require initialization of their GPIO pins first,
should be moved out of .machine_init down to late_initcall level, as the
gpio-generic driver is not available until device_initcall time. The
latch reset operation, which will be replaced with GPIO initialization,
must also be moved to late_initcall for the same reason.
Since there was already another, separate arch_initcall function for
setting up one of those latch dependent devices, the on-board modem
device, reuse that function, i.e., rename it to a name that matches the
new purpose, extend with other device setup relocated from
.machine_init, and move down to the late_initcall level.
While being at it, add missing gpio_free() in case the modem platform
device registration fails.
Thanks to Tony Lindgren <tony@atomide.com> who suggested this approach
instead of shifting up the gpio-generic driver initialization.
In addition, defer registration of the Amstrad Delta ASoC and serio
devices, done from their device driver files, until late_initcall time,
as those drivers will depend on their GPIO pins already requested from
the board late_init() function until updated to register their GPIO pins
themselves.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - fix touchpad not working after S2R on Vostro V13
Input: cma3000_d0x - fix signedness bug in cma3000_thread_irq()
Input: wacom - add product id used by Samsung Slate 7
The Cintiq 24HD has three LEDs on the left side of the tablet and
three LEDs on the right side of the tablet. Switching to LED 0,
1, or 2 will enable the top, middle, or bottom LED for the respective
side. Switching to LED 3 turns off the LEDs on the respective side.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds support for the Cintiq 24HD. There are two quirks about this
model that haven't been seen in prior tablets. First, a second
touch ring is present on this display; it is being exposed via the
ABS_THROTTLE axis. Second, three capacitive buttons at the top of
the unit are available; though physically a touch strip, we report
the use of these buttons with generic KEY_ events.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics touchpads on several Dell laptops, particularly Vostro V13
systems, may not respond properly to PS/2 commands and queries immediately
after resuming from suspend to RAM. This leads to unresponsive touchpad
after suspend/resume cycle.
Adding a 1-second delay after resetting the device allows touchpad to
finish initializing (calibrating?) and start reacting properly.
Reported-by: Daniel Manrique <daniel.manrique@canonical.com>
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver adds support for Sharp's GP2AP002A00F proximity sensor. The
proximity is measured as a binary switch, i.e. an object is either
detected or not detected. Hence, this driver is implemented as a switch
that reports SW_FRONT_PROXIMITY.
Reviewed-by: Datta Shubhrajyoti <shubhrajyoti@ti.com>
Signed-off-by: Courtney Cavin <courtney.cavin@sonyericsson.com>
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These symbols are not used outside it's driver so no need to
make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch converts mc13783-pwrbutton to use the module_platform_driver()
macro which makes the code smaller and a bit simpler.
Also staticise mc13783_pwrbutton_driver which is not used outside
this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Register input device last so that we do not have to reset
input device pointer after calling input_unregister_device().
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The error check (intr_status < 0) didn't work because intr_status is
a u8. Change its type to signed int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New product ID reported by Harvey Braun on linuxwacom mailing list
and also tested this patch with new hardware.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Having module device table based on PNP id produces the following warning:
CC drivers/input/touchscreen/htcpen.o
drivers/input/touchscreen/htcpen.c:50: warning: 'pnp_ids' defined but not used
This happens because it is not a PNP driver, bit rather ISA driver and
pnp_ids table is not used anywhere. To fix this issue let's switch to
DMI-based module table instead,
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This variant was introduced in
i2c: boilerplate function for byte swapped smbus_write/read_word_data
This also has the side effect of ensuring any errors from the i2c
read and no longer mangled.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There exist tilt switches that simply report their tilt-state via
some gpios. The number and orientation of their axes can vary
depending on the switch used and the build of the device. Also two
or more one-axis switches could be combined to provide multi-dimensional
orientation.
One example of a device using such a switch is the family of Qisda
ebook readers, where the switch provides information about the
landscape / portrait orientation of the device. The example in
Documentation/input/gpio-tilt.txt documents exactly this one-axis
device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It turns out that v4's firmware provides a command so we can query
the resolution. Let's use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Starting with v3 hardware, the firmware supports this shorter
elantech_send_cmd. Teach the driver to use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This converts the drivers in drivers/input/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Henk Vergonet <Henk.Vergonet@gmail.com>
Cc: Alessandro Rubini <rubini@ipvvis.unipv.it>
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: "Magnus Hörlin" <magnus@alefors.se>
Cc: Chris Moeller <kode54@gmail.c>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Edwin van Vliet <edwin@cheatah.nl>
Cc: Ping Cheng <pingc@wacom.com>
Cc: Eduard Hasenleithner <eduard@hasenleithner.at>
Cc: Alexander Strakh <strakh@ispras.ru>
Cc: Glenn Sommer <gsommer@datanordisk.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PM methods are basically the same for SPI and I2C busses, so let's
use the same dev_pm_ops for both of them.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the EETI eGalax serial multi touch controller driver.
EETI eGalax serial touch screen controller is a I2C based multiple
capacitive touch screen controller, it can support 5 touch events maximum.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We have determined that the jumpiness previously seen when using
the synaptics kernel mouse driver on OLPC XO was due to not using
the synaptics X11 userspace driver - the xf86-input-evdev driver was
interpreting 'finger near pad' signals as movements. Newer versions
of xf86-input-evdev fix this issue.
Additionally, the synaptics kernel driver is now usable on this
platform, but only when run in relative mode.
Update the comment and refine the check to allow the synaptics driver
to run on OLPC XO in relative mode.
We will continue investigating the EC issue as time becomes available.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is nothing in keypad platform definitions that requires
the driver be complied on Samsung platform only, so let's move them
out of the platform subdirectory and relax the dependencies.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, the synaptics driver puts the device into Absolute mode.
As explained in the synaptics documentation section 3.2, in this mode,
the device sends a continuous stream of packets at the maximum rate
to the host when the user's fingers are near or on the pad or
pressing buttons, and continues streaming for 1 second afterwards.
These packets are even sent when there is no new information to report,
even when they are duplicates of the previous packet.
For embedded systems this is a bit much - it results in a huge
and uninterrupted stream of interrupts at high rate.
This patch adds support for Relative mode, which can be selected as
a new psmouse protocol. In this mode, the device does not send duplicate
packets and acts like a standard PS/2 mouse. However, synaptics-specific
functionality is still available, such as the ability to set the packet
rate, and rather than disabling gestures and taps at the hardware level
unconditionally, a 'synaptics_disable_gesture' sysfs attribute has
been added to allow control of this functionality.
This solves a long standing OLPC issue: synaptics hardware enables
tap to click by default (even in the default relative mode), but we
have found this to be inappropriate for young children and first
time computer users. Enabling the synaptics driver disables tap-to-click,
but we have previously been unable to use this because it also enables
Absolute mode, which is too "spammy" for our desires and actually
overloads our EC with its continuous stream of packets. Now we can enable
the synaptics driver, disabling tap to click while retaining the less
noisy Relative mode.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With commit 67d0a07544 we mark strict_strtox
as obsolete. Convert all remaining such uses in drivers/input/.
Also change long to appropriate types, and return error conditions
from kstrtox separately, as Dmitry sugguests.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix the following compilation failure with v3.2-rc1 by including module.h:
CC drivers/input/serio/ams_delta_serio.o
drivers/input/serio/ams_delta_serio.c:33:15: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c:34:20: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c:35:16: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c: In function 'ams_delta_serio_init':
drivers/input/serio/ams_delta_serio.c:155:2: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/input/serio/ams_delta_serio.c:155:2: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes some v3 hardware (fw_version: 0x150500) wrongly detected
as v2 hardware.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Tested-By: Marc Dietrich <marvin24@gmx.de>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for two ALPS touchpad protocols not
supported currently by the driver, which I am arbitrarily naming
version 3 and version 4. Support is single-touch only at this time,
although both protocols are capable of limited multitouch support.
Thanks to Andrew Skalski, who did the initial reverse-engineering
of the v3 protocol.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for version 4 protocol support, which has 8-byte
data packets, remove all hard-coded assumptions about packet size
and use psmouse->pktsize instead.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for adding support for more ALPS protocol versions,
add a field for the protocol version to the model info instead of
using a field in the flags. OLDPROTO and !OLDPROTO are now called
version 1 and version 2, repsectively.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for new protocol support, move the protocol
information currently documented in alps.c to
Documentation/input/alps.txt, where it can be expanded without
cluttering up the driver.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo's Pen and Touch packets always start with a value
of 0x02 in first byte. In 3rd gen Bamboo's, the hw is now
periodically sending some additional packets with unrelated data
and uses a value other than 0x02 to inform driver this.
Ignore those packets now.
This was reported by users as bad behavior in Gimp. The
invalid packets being processed made the stylus report
out of proximity for the 1 packet and this triggered some
secondary bug which caused Gimp to stop drawing until
user really took pen out of proximity of tablet.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Touchpad input doesn't work with newer HP Pavilion dv4 laptops due to bad i8042
timeout data. Booting with i8042.notimeout and i8042.nomux successfully works
around the problem.
This patch adds the devices to the i8042 notimeout and nomux blacklists.
Signed-off-by: Tomas Miljenovic <TomasM@tomasm.tk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In addition to some laptops needing i8042 reset after resuming from S2R to
get their touchpads working there is another class of laptops - ones that
need i8042 reset before going to S2R, otherwise they will simply reboot
instead of resuming.
See https://bugzilla.kernel.org/show_bug.cgi?id=15612
This change forces reset of i8042 before doing S2R.
Reported-by: Stefan Koch <stefan_koch@gmx.net>
Tested-by: Alexander van Loon <a.vanloon@alexandervanloon.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
These files are not modules but are exporting symbols and/or
making use of THIS_MODULE macro.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in input dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (348 commits)
[media] pctv452e: Remove bogus code
[media] adv7175: Make use of media bus pixel codes
[media] media: vb2: fix incorrect return value
[media] em28xx: implement VIDIOC_ENUM_FRAMESIZES
[media] cx23885: Stop the risc video fifo before reconfiguring it
[media] cx23885: Avoid incorrect error handling and reporting
[media] cx23885: Avoid stopping the risc engine during buffer timeout
[media] cx23885: Removed a spurious function cx23885_set_scale()
[media] cx23885: v4l2 api compliance, set the audioset field correctly
[media] cx23885: hook the audio selection functions into the main driver
[media] cx23885: add generic functions for dealing with audio input selection
[media] cx23885: fixes related to maximum number of inputs and range checking
[media] cx23885: Initial support for the MPX-885 mini-card
[media] cx25840: Ensure AUDIO6 and AUDIO7 trigger line-in baseband use
[media] cx23885: Enable audio line in support from the back panel
[media] cx23885: Allow the audio mux config to be specified on a per input basis
[media] cx25840: Enable support for non-tuner LR1/LR2 audio inputs
[media] cx23885: Name an internal i2c part and declare a bitfield by name
[media] cx23885: Ensure VBI buffers timeout quickly - bugfix for vbi hangs during streaming
[media] cx23885: remove channel dump diagnostics when a vbi buffer times out
...
Fix up trivial conflicts in drivers/misc/altera-stapl/altera.c (header
file rename vs add)
This driver has been tested with hardware and works as expected. To use
it add the platform data as appropriate and register it with the
corresponding I2C bus.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (68 commits)
Input: adp5589-keys - add support for the ADP5585 derivatives
Input: imx_keypad - add pm suspend and resume support
Input: force feedback - potential integer wrap in input_ff_create()
Input: tsc2007 - make sure that X plate resistance is specified
Input: serio_raw - fix memory leak when closing char device
Input: serio_raw - kick clients when disconnecting port
Input: serio_raw - explicitly mark disconnected ports as dead
Input: serio_raw - fix coding style issues
Input: serio_raw - use dev_*() for messages
Input: serio_raw - use bool for boolean data
Input: serio_raw - perform proper locking when adding clients to list
Input: serio_raw - rename serio_raw_list to serio_raw_client
Input: serio_raw - use kref instead of rolling out its own refcounting
Input: psmouse - switch to using dev_*() for messages
Input: wacom - correct max Y value on medium bamboos
Input: wacom - add ABS_DISTANCE to Bamboo Pen reports
Input: wacom - remove unneeded touch pressure initialization
Input: lm8323 - wrap suspend and resume in CONFIG_PM_SLEEP
Input: ad7879-i2c - wrap suspend and resume in CONFIG_PM_SLEEP
Input: synaptics_i2c - wrap suspend and resume in CONFIG_PM_SLEEP
...
3rd generation Bamboo Pen and Touch tablets reuse the older
stylus packet but add an extra fixed zero pad byte to end.
The touch packets are quite different since it supports tracking
of up to 16 touches. The packet is 64-byte fixed size but contains
up to 15 smaller messages indicating data for a single touch or
for tablet button presses.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Override invalid pen based pktlen and x/y_max with touch
values from HID report.
Since active area of pen and touch are same on these
devices, set physical x/y size while pen x/y_max and
resolution are still valid.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bit 0x02 always means tip versus eraser. Bit 0x01 is something related
to version of stylus and different values are starting to be used.
Relaxing proximity check is required to be used with 3rd generation
Bamboo Pen and Touch tablets.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo's do not declared a Digitizer-Stylus so the if() was
never executed. wacom_features already contains correct stylus
packet length.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Only the stylus interface on Bamboo's has a feature report that can
be used to set to wacom mode. The touch interface only has 1 report mode
and will return errors for those get/sets requests.
The get request was always erroring out because it was not marked as
an input request. Only down side of error was needlessly resending the
set request 5 times.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
This adds support for the power-on buttons of MC13783 PMIC.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the first step to also support the touch interface of the mc13892
pmic chip.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The ADP5585 family keypad decoder and IO expander is similar to the ADP5589,
however it features less IO pins, and lacks hardware assisted key-lock
functionality. Unfortunately the register addresses are different, as well as
the event codes and bit organization within the port related registers.
Move ADP5589 Register defines from the header file into the main source file.
Add new defines while making sure we don't break existing platform_data.
Add register address translation, and turn device specific defines into variables.
Introduce some helper functions and disable functions that doesn't
exist on the added devices.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The imx_keypad driver was indicating that it was wakeup capable in
imx_keypad_probe(), but it didn't implement suspend or resume methods.
According to the i.MX series MCU Reference Manual, the kpp (keypad
port) is a major wake up source which can detect any key press even
in low power mode and even when there is no clock.
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The problem here is that max_effects can wrap on 32 bits systems.
We'd allocate a smaller amount of data than sizeof(struct ff_device).
The call to kcalloc() on the next line would fail but it would write
the NULL return outside of the memory we just allocated causing data
corruption.
The call path is that uinput_setup_device() get ->ff_effects_max from
the user and sets the value in the ->private_data struct. From there
it is:
-> uinput_ioctl_handler()
-> uinput_create_device()
-> input_ff_create(dev, udev->ff_effects_max);
I've also changed ff_effects_max so it's an unsigned int instead of
a signed int as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The VIBSELL/R bit in the VIBCTLL/R register tells the source of the data,
which is going to be used to drive the attached motor(s).
Do not allow effect execution if any of the channels are set to receive
audio data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bits within the two control registers (for left and right channel)
are identical.
Use common names for the bits acros the two register.
Also add the missing definition for the path selection bit.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Abort driver initialization if X plate resistance was not specified in
platform data as it will cause pressure to be always calculated as 0,
and making userspace ignore touch coordinates.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently we never freed memory allocated when users open our char
devices nor removed old users from the list of connected clients.
Also unregister misc device immediately upon disconnecting the port
instead of waiting until last user drops off (refcounting in misc
device code will make sure needed pieces stay around while they
are needed) and make sure we are not holing holding serio_raw_mutex
when registering/unregistering misc device. This should fix potential
deadlock between serio_raw and misc device code uncovered by lockdep
and reported by Thomas Tuttle.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Send SIGIO/POLL_HUP and otherwise wake up waiters when corresponding serio
port is being disconnected. Also check if port is dead in serio_raw_poll
and signal POLLHUP|POLLERR.
This should speed up process of releasing dead devices by userspace
applications.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of relying on setting serio_raw->serio to NULL upon disconnecting
ports mark them explicitly as "dead". Also take and carry reference to
underlying serio port to make sure it does not go away until we are done
with it.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will ensure our reporting is consistent with the rest of the system.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make sure we hold serio lock when adding clients to client list so that
we do not race with serio_raw_release() removing clients from the same
list.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
'serio_raw_list' and 'list' names do not accurately represent their objects
and are extremely confusing when reading the code. Let's use better suited
names.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will ensure our reporting is consistent with the rest of the system
and we do not refer to obsolete source file names.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: JJ Ding <dgdunix@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Medium size Bamboo P&T driver reused max X/Y form older Bamboo 1
medium size tablets and never updated to real value. Actual
active area of tablet is slightly larger in Y direction.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tablet reports a distance of 0 right at highest point possible
to be in proximity and distance_max when touching tablet. Inverse
the distance since user land has no way of knowing ABS_DISTANCE
is not distance from tablet.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These were left in during removal of touch pressure reports but not
needed now.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
lm8323.c: warning: 'lm8323_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
ad7879-i2c.c: warning: 'ad7879_i2c_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
synaptics_i2c.c: warning: 'synaptics_i2c_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes GCC is not smart enough to recognize that x, y and z are
always used properly initialized in mma8450_poll(). Let's rearrange
the code a bit to help GCC.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysfs attribute show methods are always passed a buffer of length
PAGE_SIZE. To keep from overwriting this buffer and causing havoc, use
snprintf() to guarantee we never write more than the buffer can hold.
In addition, at least for my touchscreen, the number and size of objects
was far too big to fit in a single 4K page. Therefore, this patch also
trims some redundant framing text to leave more room for actual data.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cintiq 21ux2 has two sets of four LEDs on right and left side of
the tablet, respectively.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The LED also indicates the status of the tablet. Don't turn it off.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The LED luminance level is normally lower when no button is pressed.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 71c86ce597.
The 21UX2 does have touchstrips, but they are in a somewhat-
hidden location.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the TSC-40 serial touchscreen driver and should be
compatible with TSC-10 and TSC-25.
The driver was written by Linutronix on behalf of Bachmann electronic GmbH.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver will be migrated to the RC driver API in a following
commit.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the of_property_read_u32() helper function to retrieve u32 values
from the device tree. Also do not pass the len parameter to
of_get_property if it isn't checked afterwards.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since touchscreen driver does not handle any events to be sent to the
device we can close serio port first and then unregister the input device.
Tested-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of having one large switch based on product ID use pointer to
function actually doing protocol decoding.
Tested-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add multi touch support for PenMount 6250 touch controller.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MSB and LSB of the XY axis value are switched according to the PenMount 9000 protocol. The driver name is also changed from penmountlpc, since it is not for LPC interface at all.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This essentially reverts commit f81bc788ff.
With recent work on elantech driver, I believe we now have complete support
for all elantech touchpads. So remove this hack.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
V2 hardware has many variants. This patch adddresses two issues:
- some model also has debounce packets, but with a different signature
than v3. Now we just check debounce for all v2 hardware.
- due to different scanning methods the hardware uses, x and y ranges have
to be calculated differently. And for some specific versions, we can just
see them as custom-made, so set {x, y} the same values as Windows driver
does.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Tested-by: Richard Schütz <r.schtz@t-online.de>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboos with Product ID's > 0xD4 return values unrelated to pressure
in touch 1 pressure field. They also report 2nd touch X/Y values
shifted down 1 byte (where pressure was). This results in jumpy
1 finger touch and totally invalid 2nd finger data.
For touch detection, switch to a Touch Present single bit that
all versions of Bamboo support.
For touch 2 offset, calculate offset based on a bit that is set
different between the two packet layouts.
Since touch pressure reports were removed from driver, there was
no need to be reading pressure any more.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds trackpad support for the MacBookAir4,1, released in July 2011.
It is very similar to the MacBookAir4,2 patch submitted by Joshua Dillon and
Chase Douglas.
Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
v4 hardware is a true multitouch capable touchpad (up to 5 fingers).
The packet format is quite complex, please see protocol document for
reference.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
v3 hardware's packet format is almost identical to v2 (one/three finger touch),
except when sensing two finger touch, the hardware sends 12 bytes of data.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For v2 hardware, there is no real parity check, but we can still check
some constant bits for data integrity.
Also rename elantech_check_parity_v1 to elantech_packet_check_v1 to make
these packet checking function names consistent.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Don't try to be too clever and remove ETP_EDGE_FUZZ_V2. X, Y ranges
should be just the raw resolution of the device. Otherwise, they can
cause underflow on the Y axis.
Suggested-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With newer hardware, the touchpad provides range info.
Let's use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For two finger touches the coordinate of each finger gets reported
separately but with reduced resolution.
With this change, we now have the same range for ST and MT data and
scale MT data because it has lower resolution to match ST.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix warning from Geert's build summary emails by changing "if" to
"ifdef". Thsi should fix the following:
drivers/input/misc/twl6040-vibra.c:231:5: warning: "CONFIG_PM_SLEEP" is not defined
Builds cleanly with CONFIG_PM_SLEEP enabled or disabled.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Take spinlock when entering ISR and timer routine to ensure that we do not
race while enabling/disabling FIFO interrupts.
Also we do not need to take teh spinlock in tegra_kbc_startremove() since
interrupt is completely disabled.
Tested-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For wakeup to be reliable, kbc needs to be in interrupt mode before suspend.
Created common routine to control the FIFO interrupt.
Added synchronization to ensure orderly suspend.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
WARNING: drivers/input/keyboard/built-in.o(.text+0xb55b): Section mismatch in reference from the function tc3589x_keypad_open() to the function .devinit.text:tc3589x_keypad_init_key_hardware()
The function tc3589x_keypad_open() references
the function __devinit tc3589x_keypad_init_key_hardware().
This is often because tc3589x_keypad_open lacks a __devinit
annotation or the annotation of tc3589x_keypad_init_key_hardware is wrong.
Signed-off-by: Harvey Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds INPUT_PROP_POINTER or INPUT_PROP_DIRECT as necessary to the
hardware supported by the Wacom driver. The DIRECT property is
assigned to devices with an embedded screen (i.e. touchscreens
and display tablets). The POINTER property is assigned to those
without embedded screens.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This commit enables control of the LEDs and OLED displays found on the
Wacom Intuos4 M, L, and XL. For this purpose, a new "wacom_led" attribute
group is added to the sysfs entry of the USB device.
This "wacom_led" group only shows up when the correct device (M, L, or XL)
is detected. The attributes are described in
Documentation/ABI/testing/sysfs-wacom
Signed-off-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For i2c drivers, we should use "i2c:" prefix for modalias.
MODULE_DEVICE_TABLE will setup the modulalias for us, thus adding
a MODULE_ALIAS is redundant (in addition to being incorrect).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will ensure that the device delivers input events only when there
are users.
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of using hard IRQ and workqueue solution switch to using threaded
interrupt handler to simplify the code and locking rules.
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If successful, usb_control_msg returns the number of bytes transferred,
otherwise a negative error number.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Wacom PenPartner should advertise its stylus tip and button
in addition to the eraser tool. These are both physically
present on the hardware, and emitted from 'wacom_penpartner_irq'.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad714x - read the interrupt status registers in a row
Input: ad714x - use DMA-safe buffers for spi_write()
Input: ad714x - fix endianness issues
Input: ad714xx-spi - force SPI bus into the default 8-bit mode
Input: ep93xx_keypad - add missing include of linux/module.h
Input: tnetv107x-ts - add missing include of linux/module.h
Input: max11801_ts - correct license statement
Input: atmel_mxt_ts - report pressure information from the driver
Input: bcm5974 - Add support for newer MacBookPro8,2
Input: wacom - report id 3 returns 4 bytes of data
Input: wacom - add WAC_MSG_RETRIES define
Input: wacom - add support for the Wacom Bamboo Pen (CTL-660/K)
Input: tegra-kbc - correct call to input_free_device
Input: mpu3050 - correct call to input_free_device
Input: bcm5974 - add support for touchpads found in MacBookAir4,2
Input: mma8450 - fix module device table type
Input: remove CLOCK_TICK_RATE from analog joystick driver
Change the placement of __init and __exit annotations to be consistent
with the rest of the drivers.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics image sensor touchpads track up to 5 fingers, but only report 2.
They use a special "TYPE=2" (AGM-CONTACT) packet type that reports
the number of tracked fingers and which finger is reported in the SGM
and AGM packets.
With this new packet type, it is possible to tell userspace when 4 or 5
fingers are touching.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
"4-finger scroll" is a gesture supported by some applications and
operating systems.
"Resting thumb" is when a clickpad user rests a finger (e.g., a
thumb), in a "click zone" (typically the bottom of the touchpad) in
anticipation of click+move=select gestures.
Thus, "4-finger scroll + resting thumb" is a 5-finger gesture.
To allow userspace to detect this gesture, we send BTN_TOOL_QUINTTAP.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics image sensor touchpads track 5 fingers, but only report 2.
This patch attempts to deal with some idiosyncrasies of these touchpads:
* When there are 3 or more fingers, only two are reported.
* The touchpad tracks the 5 fingers in slot[0] through slot[4].
* It always reports the lowest and highest valid slots in SGM and AGM
packets, respectively.
* The number of fingers is only reported in the SGM packet. However,
the number of fingers can change either before or after an AGM
packet.
* Thus, if an SGM reports a different number of fingers than the last
SGM, it is impossible to tell whether the intervening AGM corresponds
to the old number of fingers or the new number of fingers.
* For example, when going from 2->3 fingers, it is not possible to tell
whether tell AGM contains slot[1] (old 2nd finger) or slot[2] (new
3rd finger).
* When fingers are added one at at time, from 1->2->3, it is possible to
track which slots are contained in the SGM and AGM packets:
1 finger: SGM = slot[0], no AGM
2 fingers: SGM = slot[0], AGM = slot[1]
3 fingers: SGM = slot[0], AGM = slot[2]
* It is also possible to track which slot is contained in the SGM when 1
of 2 fingers is removed. This is because the touchpad sends a special
(0,0,0) AGM packet whenever all fingers are removed except slot[0]:
Last AGM == (0,0,0): SGM contains slot[1]
Else: SGM contains slot[0]
* However, once there are 3 fingers, if exactly 1 finger is removed, it
is impossible to tell which 2 slots are contained in SGM and AGM.
The (SGM,AGM) could be (0,1), (0,2), or (1,2). There is no way to know.
* Similarly, if two fingers are simultaneously removed (3->1), then it
is only possible to know if SGM still contains slot[0].
* Since it is not possible to reliably track which slot is being
reported, we invalidate the tracking_id every time the number of
fingers changes until this ambiguity is resolved when:
a) All fingers are removed.
b) 4 or 5 fingers are touched, generates an AGM-CONTACT packet.
c) All fingers are removed except slot[0]. In this special case, the
ambiguity is resolved since by the (0,0,0) AGM packet.
Behavior of the driver:
When 2 or more fingers are present on the touchpad, the kernel reports
up to two MT-B slots containing the position data for two of the fingers
reported by the touchpad. If the identity of a finger cannot be tracked
when the number-of-fingers changes, the corresponding MT-B slot will be
invalidated (track_id set to -1), and a new track_id will be assigned in
a subsequent input event report.
The driver always reports the total number of fingers using one of the
EV_KEY/BTN_TOOL_*TAP events. This could differ from the number of valid
MT-B slots for two reasons:
a) There are more than 2 fingers on the pad.
b) During ambiguous number-of-fingers transitions, the correct track_id
for one or both of the slots cannot be determined, so the slots are
invalidated.
Thus, this is a hybrid singletouch/MT-B scheme. Userspace can detect
this behavior by noting that the driver supports more EV_KEY/BTN_TOOL_*TAP
events than its maximum EV_ABS/ABS_MT_SLOT.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A Synaptics image sensor tracks 5 fingers, but can only report 2.
The algorithm for choosing which 2 fingers to report and in which packet:
Touchpad maintains 5 slots, numbered 0 to 4
Initially all slots are empty
As new fingers are detected, assign them to the lowest available slots
The touchpad always reports:
SGM: lowest numbered non-empty slot
AGM: highest numbered non-empty slot, if there is one
In addition, these touchpads have a special AGM packet type which reports
the number of fingers currently being tracked, and which finger is in
each of the two slots. Unfortunately, these "TYPE=2" packets are only used
when more than 3 fingers are being tracked. When less than 4 fingers
are present, the 'w' value must be used to track how many fingers are
present, and knowing which fingers are being reported is much more
difficult, if not impossible.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics makes (at least) two kinds of touchpad sensors:
* Older pads use a profile sensor that could only infer the location
of individual fingers based on the projection of their profiles
onto row and column sensors.
* Newer pads use an image sensor that can track true finger position
using a two-dimensional sensor grid.
Both sensor types support an "Advanced Gesture Mode":
When multiple fingers are detected, the touchpad sends alternating
"Advanced Gesture Mode" (AGM) and "Simple Gesture Mode" (SGM)
packets.
The AGM packets have w=2, and contain reduced resolution finger data
The SGM packets have w={0,1} and contain full resolution finger data
Profile sensors try to report the "upper" (larger y value) finger in
the SGM packet, and the lower (smaller y value) in the AGM packet.
However, due to the nature of the profile sensor, they easily get
confused when fingers cross, and can start reporting the x-coordinate
of one with the y-coordinate of the other. Thus, for profile
sensors, "semi-mt" was created, which reports a "bounding box"
created by pairing min and max coordinates of the two pairs of
reported fingers.
Image sensors can report the actual coordinates of two of the fingers
present. This patch detects if the touchpad is an image sensor and
reports finger data using the MT-B protocol.
NOTE: This patch only adds partial support for 2-finger gestures.
The proper interpretation of the slot contents when more than
two fingers are present is left to later patches. Also,
handling of 'number of fingers' transitions is incomplete.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When a Synaptics touchpad is in "AGM" mode, and multiple fingers are
detected, the touchpad sends alternating "Advanced Gesture Mode" (AGM) and
"Simple Gesture Mode" (SGM) packets.
The AGM packets have w=2, and contain reduced resolution finger data.
The SGM packets have w={0,1} and contain full resolution finger data.
Refactor the parsing of agm packets to its own function, and rename the
synaptics_data.mt field to .agm to indicate that it contains the contents of
the last agm packet.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics touchpads report increasing y from bottom to top.
This is inverted from normal userspace "top of screen is 0" coordinates.
Thus, the kernel driver reports inverted y coordinates to userspace.
This patch refactors this inversion.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since touchscreen driver does not handle any events to be sent to the
device we can close serio port first and then unregister the input device.
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Implement open() and close() methods for the input device so that we
do not start the device unless there are users listening to the events.
Acked-by: Chris Bagwell <chris@cnpbagwell.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The interrupt status registers should be read in row to avoid invalid data.
Alter "read" method for both bus options to allow reading several registers
in a row and make sure we read interrupt status registers properly.
Read sequence saves 50% of bus transactions compared to single register
reads. So use it also for the result registers, which are also located
in a row.
Also update copyright notice.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Michael Thalmeier