The probe function at the moment only frees the netdev but does not disconnect
the phy or removes the mdio bus it registered.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a newline character appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook the Broadcom SYSTEMPORT driver into the build system under the
SYSTEMPORT Kconfig symbol.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT is the latest Ethernet MAC hardware block used on newer
BCM7xxx Set Top Box SoCs in conjunction with an internal Ethernet
switch. This patch adds support for this hardware block along with the
following hardware features:
- support for hardware checksum offload (transmit and receive)
- support for the 32 transmit queues
- MIB counters reading
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the PTP Tx timestamp interrupt handler. The original
code misinterpreted the interrupt handler design. We were clearing the
ena_mask bit for the Timesync interrupts. This is done to indicate that
the interrupt will be handled in a scheduled work item (instead of
immediately) and that work item is responsible for re-enabling the
interrupts. However, the Tx timestamp was being handled immediately and
nothing was ever re-enabling it. This resulted in a single interrupt
working for the life of the driver.
This patch fixes the issue by instead clearing the bit from icr0 which
is used to indicate that the interrupt was immediately handled and can
be re-enabled right away. This patch also clears up a related issue due
to writing the PRTTSYN_STAT_0 register, which was unintentionally
clearing the cause bits for Timesync interrupts.
Change-ID: I057bd70d53c302f60fab78246989cbdfa469d83b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb only.
Carolyn provides a number of cleanups to fix checkpatch warnings/errors
and two minor issues found by coccicheck.
v2: update patch indentation for patch 07 of the series based on feedback
from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlNZi6kACgkQjTAFq1RaXHO1YACfXTdM/OBitnFB8Jy2EiCj87tb
Z2cAn3rrgz7LBLq2WoypQLc9JxeJUwqu
=pdU3
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.16-20140425' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
this is a pull request of 10 patches for net-next/master.
It consists of three patches by Alexander Shiyan, which improve the
mcp251x driver. Stefano Babic's patch move the SPI driver into a sub
folder. The three patches by Olivier Sobrie add support for the Kvaser
Leaf v2 and usb mini PCIe hardware to the existing driver. Alexander
Stein contributes eg20t support to the c_can pci driver. Together with
the patches on the net-tree, we'll be able to remove the pch_can driver
soon. Kurt Van Dijck's two patches clean up the sysfs attributes of the
softing driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlNZf5EACgkQjTAFq1RaXHPFhACghgdQaxG++36VEhtToY+H8o2x
3UUAniZ+DbwtSapriPekjVKRC7VuQFsD
=N5FA
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.15-20140424' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
this is a pull request for net/master, for the v3.15 release cycle, consisting
of 26 patches.
Thomas Gleixner contributes 21 patches for the c_can driver, which address
several shortcomings in the driver like hardware initialisation, concurrency,
message ordering and poor performance. Two patches Oliver Hartkopp, one adds a
missing lock to the sja1000_isa driver, the other one fixes the return value in
the generic bit time configuration function. And finally a patch by Alexander
Stein, that fixes the slcan driver to use the correct spinlock variant.
To make it 26 patches, Wolfgang Grandegger patch for the c_can_pci
driver, which enables the bus master only for MSI and a patch by
Wolfram Sang, which converts the 'instance' in the c_can driver to the
proper type.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the name used by Ethtool to something more
conventional in preparation for TSE Ethtool register dump
support to be added in the near future.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a fault in the error recovery path of the probe
routine where the netdev structure was not being unregistered properly
leading to a panic only when the phy probe failed.
Abbreviated panic stack seen is as follows:
(free_netdev+0xXX) from (altera_tse_probe+0xXX)
(altera_tse_probe+0xXX) from (platform_drv_probe+0xXX)
(platform_drv_probe+0xXX) from (driver_probe_device+0xXX)
(driver_probe_device+0xXX) from (__driver_attach+0xXX)
(__driver_attach+0xXX) from (bus_for_each_dev+0xXX)
(bus_for_each_dev+0xXX) from (driver_attach+0xXX)
(driver_attach+0xXX) from (bus_add_driver+0xXX)
(bus_add_driver+0xXX) from (driver_register+0xXX)
(driver_register+0xXX) from (__platform_driver_register+0xXX)
(__platform_driver_register+0xXX) from (altera_tse_driver_init+0xXX)
(altera_tse_driver_init+0xXX) from (do_one_initcall+0xXX)
(do_one_initcall+0xXX) from (kernel_init_freeable+0xXX)
(kernel_init_freeable+0xXX) from (kernel_init+0xXX)
(kernel_init+0xXX) from (ret_from_fork+0xXX)
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch initializes the pause quanta set for transmitted pause frames
to the IEEE specified default of 0xffff.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch works around a recently discovered unaligned receive dma problem
with the Altera SGMDA. The Altera SGDMA component cannot be configured to
DMA data to unaligned addresses for receive packet operations from the
Triple Speed Ethernet component because of a potential data transfer
corruption that can occur. This patch addresses this issue by
utilizing the shift 16 bits feature of the Altera Triple Speed Ethernet
component and modifying the receive buffer physical addresses accordingly
such that the target receive DMA address is always aligned on a 32-bit
boundary.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Tested-by: Matthew Gerlach <mgerlach@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is small enough, we don't need a extra function for this.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a unnecessary state read. The status value is never
evaluate after reading the state.
Also rename the status variable to dvdd, because this variable will be
used later.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resets the irq line before we are requesting the irq. This
avoids pending interrupts before requesting.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is already handled by the of_match_ptr macro.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a at86rf230_device_id table to offers various module
aliases.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace the gpio_request functions with devm_gpio_request_one
functions. Then we don't need to take care about freeing gpios.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace request_irq with devm_request_irq. With
devm_request_irq we don't need to care about freeing the irq.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to set these values at request_irq. The interrupt line is
already configured to same value like irq_get_trigger_type returned.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the platform data for the irq_type. We use instead
the irq_get_trigger_type function to get these flags which should
already configured by the interrupt controller.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 2dc33bbc "bnx2x: Remove the sriov VFOP mechanism",
the bnx2x started enforcing vlan credits for all vlan configurations.
This exposed 2 issues:
- Vlan credits are not returned once a VF is removed; this causes a leak
of credits, and eventually will lead to VFs with no vlan credits.
- A vlan credit must be set aside for the Hypervisor to use, and should
not be visible to the VF.
Although linux VFs at the moment do not support vlan configuration [from the
VF side] which causes them to be resilient to this sort of issue, Windows VF
over linux hypervisors might fail to load as the vlan credits become depleted.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VF interface, the driver fails to release that VF's mailbox
and bulletin board allocated memory.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
brcmfmac has been broken on my cubietruck with a BCM43362:
brcmfmac: brcmf_chip_recognition: found AXI chip: BCM43362, rev=1
brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0:
Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
since commit 53036261033: "brcmfmac: update core reset and disable routines".
The problem is that since this commit brcmf_chip_ai_resetcore no longer sets
BCMA_IOCTL itself before bringing the core out of reset, instead relying on
brcmf_chip_ai_coredisable to do so. But brcmf_chip_ai_coredisable is a nop
of the chip is already in reset. This patch modifies brcmf_chip_ai_coredisable
to always set BCMA_IOCTL even if the core is already in reset.
This fixes brcmfmac hanging in firmware loading on my board.
Cc: stable@vger.kernel.org # v3.14
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: move sc_flags to ath_common" moved setting
ATH_OP_INVALID flag below ieee80211_register_hw. This is causing
the flag never being cleared randomly as the drv_start is called
prior to setting flag. Fix this by setting the flag prior to
register_hw.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit e050c76fcf.
I'm not sure what crack pipe I was using when I merged this...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes issue found by updated coccicheck.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes issues found by updated coccicheck.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:AVOID_EXTERNS found by checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes implementation to remove use of DEFINE_PCI_DEVICE_TABLE.
This patch fixes WARNING:DEFINE_PCI_DEVICE_TABLE
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes ERROR:INITIALISED_STATIC from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:MSLEEP found by checkpatch check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:LONG_LINE found with checkpatch check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes ERROR:RETURN_PARENTHESES from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:MISSING_BREAK found with checkpatch check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes ERROR:ASSIGN_IN_IF found with checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:NETWORKING_BLOCK_COMMENT_STYLE from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:TRAILING_STATEMENT from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes ERROR:POINTER_LOCATION from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'frequency' indicates the embedded cpu's frequency, but that
should not be necessary for any purpose.
'txpending' is an attribute for debugging.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
netdev->dev_id obsoletes this property.
None of the remaining properties contribute to udev detection methods.
The regular calls for the sysfs group can thus safely be restored.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add two new USB devices supported by the driver and fix bad
english.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the Kvaser Leaf v2 and Leaf usb mini
PCIe card.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On some Kvaser hardware, the firmware returns extra messages after the
request for card info. For instance on a Leaf Light v2:
--> CMD_GET_CARD_INFO
<-- CMD_USB_THROTTLE
<-- CMD_GET_CARD_INFO2
<-- CMD_GET_CARD_INFO_REQ
When it happens, the probing function fails because we only read
the first usb message.
To overcome this issue, we add a mechanism of retries to the
kvaser_usb_wait_msg() function.
I tested this patch with the following hardware:
- Kvaser Leaf Light
- Kvaser Leaf Light v2
- Kvaser USBCan R
This patch is necessary for the Leaf Light v2 hardware.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Create a directory for all CAN drivers using SPI and move mcp251x driver there.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds check for mcp251x_hw_reset() result on startup and
removes unnecessary checking for CANSTAT register since this value
is being checked in mcp251x_hw_reset().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The MCP251x utilizes an oscillator startup timer (OST), which holds the
chip in reset, to insure that the oscillator has stabilized before the
internal state machine begins to operate. The OST maintains reset for
the first 128 OSC clock cycles after power up or reset.
So, this patch removes unnecessary loops and reduce delay for power on
and reset to the safe value.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves setup of SPI bus a bit earlier and adds check for spi_setup()
result to be sure SPI bus is communicating with the device properly.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
slc_xmit is called within softirq context and locks sl->lock, but
slcan_write_wakeup is not softirq context, so we need to use
spin_[un]lock_bh!
Detected using kernel lock debugging mechanism.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When trying to set a data bitrate on non CAN FD devices the 'ip' tool
answers with:
RTNETLINK answers: Unknown error 524
Rename '-ENOTSUPP' to '-EOPNOTSUPP' so that 'ip' answers correctly:
RTNETLINK answers: Operation not supported
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When accessing the SJA1000 controller registers in the indirect access mode,
writing the register number and reading/writing the data has to be an atomic
attempt.
As the sja1000_isa driver is an old style driver with a fixed number of
instances the locking variable depends on the same index like all the other
configuration elements given on the module command line.
As a positive side effect dev->dev_id is populated by the instance index,
which was missing in 3e66d0138c ("can: populate netdev::dev_id for udev
discrimination").
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Coverity complains that c_can_pci_probe() calls pci_enable_msi() without
checking the result:
CID 712278 (#1 of 1): Unchecked return value (CHECKED_RETURN) 3. check_return:
Calling pci_enable_msi_block without checking return value (as is done
elsewhere 88 out of 105 times).
88 pci_enable_msi(pdev);
This is CID 712278.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch allows to switch the netns when packet is encapsulated or
decapsulated.
The vxlan socket is openned into the i/o netns, ie into the netns where
encapsulated packets are received. The socket lookup is done into this netns to
find the corresponding vxlan tunnel. After decapsulation, the packet is
injecting into the corresponding interface which may stand to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Configuration example:
ip netns add netns1
ip netns exec netns1 ip link set lo up
ip link add vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
ip link set vxlan10 netns netns1
ip netns exec netns1 ip addr add 192.168.0.249/24 broadcast 192.168.0.255 dev vxlan10
ip netns exec netns1 ip link set vxlan10 up
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6439fbce10 (can: c_can: fix error checking of priv->instance in
probe()) found the warning but applied a suboptimal solution. Since, both
pdev->id and of_alias_get_id() return integers, it makes sense to convert the
variable to an integer and avoid the cast.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's suffcient to kill the TXIE bit in the message control register
even if the documentation of C and D CAN says that it's not allowed to
do that while MSGVAL is set. Reality tells a different story and this
change gives us another 2% of CPU back for not waiting on I/O.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mark suggested to use one IF for the softirq and the other for the
xmit function to avoid the xmit lock.
That requires to write the frame into the interface first, then handle
the echo skb and store the dlc before committing the TX request to the
message ram.
We use an atomic to handle the active buffers instead of reading the
MSGVAL register as thats way faster especially on PCH/x86.
Suggested-by: Mark <mark5@del-llc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of obfuscating the code by artificial 16 bit splits use the
proper 32 bit assignments and split the result when writing to the
interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove the MASK from the TX transfer side.
Make the code readable and get rid of the annoying IFX_WRITE_XXX_16BIT
macros which are just obfuscating the code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sigh!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Alexander reported that the new optimized handling of the RX fifo
causes random packet loss on Intel PCH C_CAN hardware.
After a few fruitless debugging sessions I got hold of a PCH (eg20t)
afflicted system. That machine does not have the CAN interface wired
up, but it was possible to reproduce the issue with the HW loopback
mode.
As Alexander observed correctly, clearing the NewDat flag along with
reading out the message buffer causes that issue on C_CAN, while D_CAN
handles that correctly.
Instead of restoring the original message buffer handling horror the
following workaround solves the issue:
transfer buffer to IF without clearing the NewDat
handle the message
clear NewDat bit
That's similar to the original code but conditional for C_CAN.
I really wonder why all user manuals (C_CAN, Intel PCH and some more)
recommend to clear the NewDat bit right away. The knows it all Oracle
operated by Gurgle does not unearth any useful information either. I
simply cannot believe that we are the first to uncover that HW issue.
Reported-and-tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The RX buffer split causes packet loss in the hardware:
What happens is:
RX Packet 1 --> message buffer 1 (newdat bit is not cleared)
RX Packet 2 --> message buffer 2 (newdat bit is not cleared)
RX Packet 3 --> message buffer 3 (newdat bit is not cleared)
RX Packet 4 --> message buffer 4 (newdat bit is not cleared)
RX Packet 5 --> message buffer 5 (newdat bit is not cleared)
RX Packet 6 --> message buffer 6 (newdat bit is not cleared)
RX Packet 7 --> message buffer 7 (newdat bit is not cleared)
RX Packet 8 --> message buffer 8 (newdat bit is not cleared)
Clear newdat bit in message buffer 1
Clear newdat bit in message buffer 2
Clear newdat bit in message buffer 3
Clear newdat bit in message buffer 4
Clear newdat bit in message buffer 5
Clear newdat bit in message buffer 6
Clear newdat bit in message buffer 7
Clear newdat bit in message buffer 8
Now if during that clearing of newdat bits, a new message comes in,
the HW gets confused and drops it.
It does not matter how many of them you clear. I put a delay between
clear of buffer 1 and buffer 2 which was long enough that the message
should have been queued either in buffer 1 or buffer 9. But it did not
show up anywhere. The next message ended up in buffer 1. So the
hardware lost a packet of course without telling it via one of the
error handlers.
That does not happen on all clear newdat bit events. I see one of 10k
packets dropped in the scenario which allows us to reproduce. But the
trace looks always the same.
Not splitting the RX Buffer avoids the packet loss but can cause
reordering. It's hard to trigger, but it CAN happen.
With that mode we use the HW as it was probably designed for. We read
from the buffer 1 upwards and clear the buffer as we get the
message. That's how all microcontrollers use it. So I assume that the
way we handle the buffers was never really tested. According to the
public documentation it should just work :)
Let the user decide which evil is the lesser one.
[ Oliver Hartkopp: Provided a sane config option and help text and
made me switch to favour potential and unlikely reordering over
packet loss ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver handles pointlessly TWO interrupts per packet. The reason
is that it enables the status interrupt which fires for each rx and tx
packet and it enables the per message object interrupts as well.
The status interrupt merily acks or in case of D_CAN ignores the TX/RX
state and then the message object interrupt fires.
The message objects interrupts are only useful if all message objects
have hardware filters activated.
But we don't have that and its not simple to implement in that driver
without rewriting it completely.
So we can ditch the message object interrupts and handle the RX/TX
right away from the status interrupt. Instead of TWO we handle ONE.
Note: We must keep the TXIE/RXIE bits in the message buffers because
the status interrupt alone is not reliable enough in corner cases.
If we ever have the need for HW filtering, then this code needs a
complete overhaul and we can think about it then. For now we prefer a
lower interrupt load.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On D_CAN the RXOK, TXOK and LEC bits are cleared/set on read of the
status register. No need to update them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of writing to the message object we can simply clear the
NewDat bit with the get method.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the allocation of the error skb fails, we still want to see the
error statistics.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reading the LEC type with
return (mode & ENABLED) && (status & LEC_MASK);
is not guaranteed to return (status & LEC_MASK) if the enabled bit in
mode is set. It's guaranteed to return 0 or !=0.
Remove the inline function and call unconditionally into the
berr_handling code and return early when the reporting is disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the allocation of an error skb fails, the state change handling
returns w/o doing any work. That leaves the interface in a wreckaged
state as the internal status is wrong.
Split the interface handling and the skb handling.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb(). It might be freed or reused. Not really harmful as
its a read access, except you turn on the proper debugging options
which catch a use after free.
The whole can subsystem is full of this. Copy and paste ....
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The state change handler is called with device interrupts disabled
already. So no point in disabling them again when we enter bus off
state.
But what's worse is that we reenable the interrupts at the end of NAPI
poll unconditionally. So c_can_start() which is called from the
restart timer can trigger interrupts which confuse the hell out of the
half reinitialized driver/hw.
Remove the pointless device interrupt disable in the BUS_OFF handler
and prevent reenabling the device interrupts at the end of the poll
routine when the current state is BUS_OFF.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
c_can_start() enables interrupts way too early. The first enabling
happens when setting the control mode in c_can_chip_config() and then
again at the end of the function.
But that happens before napi_enable() and that means that an interrupt
which comes in will disable interrupts again and call napi_schedule,
which ignores the request and the later napi_enable() is not making
thinks work either. So the interface is up with all device interrupts
disabled.
Move the device interrupt after napi_enable() and add it to the other
callsites of c_can_start() in c_can_set_mode() and c_can_power_up()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
All type checks in c_can.c are != BOSCH_D_CAN so nobody noticed so far
that the pci code does not update the type information.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the ARRAY_SIZE macro to determine the number of entries in
bcm_enet_gstrings_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a seg fault on 'ethtool -A' entry if the
interface is down. Obviously we need to have the
phy device initialized / "connected" (see of_phy_connect())
to be able to advertise pause frame capabilities.
Fixes: 23402bddf9
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In case QLC_83XX_MBX_CMD_NO_WAIT command type the calling
function does not free the memory as it does not wait for
response. So free it when get a response from adapter after
sending the command.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware versions fails to reset the lock during
initialization. Force reset firmware API lock during driver
probe to ensure lock availability.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two breaks missing there. The result is that userspace
receives multiple messages which might be confusing.
Introduced-by: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was told that the Cadence macb driver is also useful on Microblaze.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/igb/e1000_mac.c
net/core/filter.c
Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine some macros that were conditioned upon SMC_DEBUG level.
By allowing compiler to verify parameters used by these macros
unconditionally, we can flag compilation failures.
Compiler will still optimize out the unused code path depending on
SMC_DEBUG, so this is a net gain.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aggresive load balancing causes packet re-ordering as active
flows are moved from a slave to another within the group. Sometime
this aggresive lb is not necessary if the preference is for less
re-ordering. This parameter if used with value "0" disables
this dynamic flow shuffling minimizing packet re-ordering. Of course
the side effect is that it has to live with the static load balancing
that the hashing distribution provides. This impact is less severe if
the correct xmit-hashing-policy is used for the tlb setup.
The default value of the parameter is set to "1" mimicing the earlier
behavior.
Ran the netperf test with 200 stream for 1 min between two hosts with
4x1G trunk (xmit-lb mode with xmit-policy L3+4) before and after these
changes. Following was the command used for those 200 instances -
netperf -t TCP_RR -l 60 -s 5 -H <host> -- -r81920,81920
Transactions per second:
Before change: 1,367.11
After change: 1,470.65
Change-Id: Ie3f75c77282cf602e83a6e833c6eb164e72a0990
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-organized the xmit function for the lb mode separating tlb xmit
from the alb mode. This will enable use of the hashing policies
like 802.3ad mode. Also extended use of xmit-hash-policy to tlb mode.
Now the tlb-mode defaults to BOND_XMIT_POLICY_LAYER2 if the xmit policy
module parameter is not set (just like 802.3ad, or Xor mode).
Change-Id: I140257403d272df75f477b380207338d0f04963e
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separating the actual xmit part from the function in a separate
function that can be used in the tlb_xmit in the next patch. Also
there is no reason do_tx_balance to be an int so changing it to
bool type.
Change-Id: I9c48ff30487810f68587e621a191db616f49bd3b
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modified the hash function to return just hash separating from the
modulo operation that can be performed by the caller. This is to
make way for the tlb mode to use the same hashing policies that
are used in the 802.3ad and Xor mode.
Change-Id: I276609e87e0ca213c4d1b17b79c5e0b0f3d0dd6f
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to ixgbe, ixgbevf, e1000e, igb and i40e.
Jacob converts the ixgbe low_water into an array which allows the
algorithm to output different values for different TCs and we can
distinguish between them. Removes vlan_filter_disable() and
vlan_filter_enable() in ixgbe so that we can do the work directly in
set_rx_mode(). Changes the setting of multicast filters only when
the interface is not in promiscuous mode for multicast packets in
ixgbe. Improves MAC filter handling by adding mac_table API based
on work done for igb, which includes functions to add/delete MAC
filters.
Mark changes register reads in ixgbe to an out-of-line function since
register reads are slow.
Emil provides a ixgbevf patch to update the driver description since
it supports more than just 82599 parts now.
David provides several cleanup patches for e1000e which resolve some
checkpatch issues as well as changing occurrences of returning 0 or 1 in
bool functions to returning true false or true.
Carolyn provides several cleanup patches for igb which fix checkpatch
warnings.
Mitch provides a fix for i40evf where the driver would correctly allow
the virtual function link state to be controlled by 'ip set link', but
would not report it correctly back. This is fixed by filling out
the appropriate field in the VF info struct.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This was caught when using a spatch (aka. coccinelle) script
written by Joe Perches.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should make the driver usable with VIA/WonderMedia ARM-based
Systems-on-Chip integrated Rhine III adapters. Note that these
are always in MMIO mode, and don't have any known EEPROM.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more generic data structures instead of struct pci_dev wherever
possible in preparation for OF bus binding
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove legacy PCI DMA wrappers and instead use generic DMA functions
directly in preparation for OF bus binding
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to fix rtnelink notification. The main problem was
about notification for fdb entry with more than one remote. Before the patch,
when a remote was added to an existing fdb entry, the kernel advertised the
first remote instead of the added one. Also when a remote was removed from a fdb
entry with several remotes, the deleted remote was not advertised.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz9021_load_values_from_of() val2 to val4 aren't tested against their
initialization value.
This causes the test to always succeed, and this value to be used as if it
was loaded from the devicetree instead of being ignored, in case of a
missing/invalid property in the ethernet OF device node.
As a result, the value "0" is written to the relevant registers.
Change the conditions to test against the right initialization value.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch that moved broadcasts to process context added
a couple of bugs on the error path where we may dereference NULL
or leak an skb. This patch fixes them.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The union contains only one member now, so we use the variables in it directly.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed recv_pkt_list and lock, and updated related code, so that
the locking overhead is reduced especially when multiple channels
are in use.
The recv_pkt_list isn't actually necessary because the packets are
processed sequentially in each channel. It has been replaced by a
local variable, and the related lock for this list is also removed.
The is_data_pkt field is not used in receive path, so its assignment
is cleaned up.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the driver would correctly allow the VF link state to be
controlled by 'ip set link', it would not report it correctly back.
Fix this by filling out the appropriate field in the vf info struct.
Change-ID: I58d8e356438190e1ee9660b424301af6f416cdbe
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:LEADING_SPACE, WARNING:SPACING, ERROR:SPACING,
WARNING:SPACE_BEFORE_TAB and ERROR_CODE_INDENT from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:BRACES and ERROR:OPEN_BRACE from
checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:PREFER_PR_LEVEL and WARNING:SPLIT_STRING
from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixing "WARNING:SPACING: Unnecessary space before function pointer arguments"
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixing "WARNING:SPACING: networking uses a blank line after declarations"
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing occurrences of returning 0 and 1 from bool functions to false and
true, respectively
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes 82599 from the description of the ixgbevf module
since the VF driver is supported on other parts as well.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add mac_table API based on work done for igb, which includes functions
to add and delete mac filters. This simplifies code for various entities
that use MAC filters such as VMDQ, SR-IOV, MACVLAN, and such.
Reported-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In line with changes done by Alex Duyck regarding unicast filters, we
now only set multicast filters when the interface is not in promiscuous
mode for multicast packets. This also has an impact on the RAR usage
such that SR-IOV has some RARs reserved for its own usage.
Reported-by: Alex Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously these functions handled stripping setup as well, but this has
already been removed from these functions. Rather than encapsulating
this into a function, we can just do the work directly in set_rx_mode.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Register reads are slow, so don't inline them.
Size before:
text data bss dec hex filename
226337 8280 552 235169 396a1 ixgbe.ko
Size after:
text data bss dec hex filename
194578 8280 552 203410 31a92 ixgbe.ko
for about a 14% reduction in text size.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since fc.high_water is an array, we should treat low_water as an array
also. This allows the algorithm to output different values for different
TCs, and then we can distinguish between them. In addition, this patch
changes one path that didn't honor the return value from ixgbe_setup_fc.
Reported-by: Aaron Salter <aaron.k.salter@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and i40evf.
Greg provides two patches for i40e, the first adds the netdev ops to support
the addition of static FDB entries in the physical function (PF) MAC/VLAN
filter table so that the virtual functions (VFs) can communicate with
bridged virtual Ethernet ports such as those provided by the virtio
driver. The second is to fix an issue where the assignment of a port
VLAN after it is already up and running requires the VF driver to be
reloaded, so print a message warning the host administrator about the
need to reload the VF driver. In addition, knock the VF offline so that
it does not continue to receive traffic not on the port VLAN assigned to
it.
Jesse provides a patch for i40e and i40evf to unhide and enable the
PREFENA field in the receive host memory cache (RX-HMC) for best
performance.
Mitch provides a i40e patch to implement the net device op for Tx
bandwidth setting.
Catherine removes a firmware workaround that is no longer needed with
the latest firmware for i40e. She also provides some minor cleanups
as well bumps the driver versions.
Anjali provides a fix for i40e displaying IPv4 flow director filters
which needed additional information to be communicated up above in
order for it to be displayed correctly.
Shannon adds tracking of the NVM busy state so that the driver won't
allow a new NVM update command until a completion event is received
from the current update. Updates the admin queue API to reflect
recent changes in the firmware. Also rearranges the "if netdev" logic
to prepare for handling non-netdev VSIs. Lastly rework the fdir
setup and tear down to use the newly created i40e_vsi_open() and
i40e_vsi_close(), which also fixes a memory leak of the FDIR queue
buffer info structs across a reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This be2net patch implements the get/set_rxfh() ethtool hooks.
RSS_CONFIG device command is invoked to set hashkey and indirection table.
It also uses an initial random value for RSS hash key instead of a
hard-coded value as hard-coded values for a hash-key are usually
considered a security risk.
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SMC_DEBUG >= 2, we hit the following compilation error:
drivers/net/ethernet/smsc/smc91x.c:85:0:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_findirq’:
drivers/net/ethernet/smsc/smc91x.c:1784:9: error: ‘dev’ undeclared (first use in this function)
DBG(2, dev, "%s: %s\n", CARDNAME, __func__);
^
Fix it by passing in the appropriate netdev pointer.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds phy_found error path when there is no phy device
and changes bus_name.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves cksum_ctl to tx_rd_des23 from cksum_pktlen for correct checksum
offloading and modifies size for Tx/Rx descriptor.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Execute "ethtool -L eth0 combined 0" in guest, if multiqueue
is enabled, virtnet_send_command() will return -EINVAL error,
there is a validation in QEMU.
But if multiqueue is disabled, virtnet_set_queues() will just
return zero (success). We should return error for this situation.
Signed-off-by: Amos Kong <akong@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC address retrieved from dt was not actually written to the
hardware. This meant proper communication was only possible after
changing the MAC address.
Fix that by always writing the mac address during probing.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first step to remove leftover code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've implemented table calculation, but forgot to enable writing it in
power setup function.
By the way document table layout.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Logic in specs and our code was wrong. Init and calibration values for
newer cards depend on radio revision, not PHY revision.
To make code clearer, change tables names to include "radio" or "phy".
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They were extracted from MMIO dumps of 14e4:4353 and wl 6.30.223.141.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 0x200 has been noticed in the following log:
radio_read(0x02ca) -> 0x0000
radio_write(0x00ca) <- 0x0080
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New Broadcom drivers don't upload it anymore. It was probably a copy & paste
mistake in early N-PHY rev 3+ days.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently AMSDU and AMPDU aggregation is enabled for TID 0 to
TID 5 streams. Lets enable it for remaining two streams also.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results for 11ac chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware dump feature is added for PCIe based chipsets.
Separate file will be created at /var/log/fw_dump_*
for each memory segment.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option be useful to dump firmware memory for debugging
purpose. Actual code to dump firmware momory for SDIO and PCIe
chipsets will be added later.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After changing local per interface beacon setting restore original
global beaconing state.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When command timeout occurs due to a firmware/hardware bug,
there is no chance of next command being successful. We will
keep cmd_sent flag on so that next command won't be sent to
firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IE's are parsed from beacon buffer and stored locally using
mwifiex_update_bss_desc_with_ie() function.
Sometimes the local pointers point to the data inside IE, but
while using them it is assumed that they are pointing to the IE
itself.
These issues are fixed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'add_remove_card_sem' semaphore already takes care of
synchronization for driver load and unload threads.
Hence there won't be a case when unload thread is waiting on
'wait_for_completion(fw_load)'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option allows driver to finish pending operations in
disconnect handler by not killing URBs after usb_deregister
call.
We will get rid of global pointer 'usb_card' by moving code
from cleanup_module() to disconnect(). This will help to match
with our handling for SDIO and PCIe interfaces.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New skbs are allocated at the time of AMSDU aggregation. Setting
up in timestamps for such skbs was missing which would result
into wrong queue delays passed to FW. Fix this by setting
timestamp of skbs created for AMSDU aggregation.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Command nodes are increased from 20 to 50. Now we can always
scan 1 channel per scan command to avoid traffic delay/loss in
connected state. We will get rid of *CHANNEL_PER_SCAN_CMD macros
used due to command node constraints.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PCIe, aggregate more AMSDU packets till PCIe TXBD is full.
For SDIO, aggregation was disabled for AMSDU packets because
AMSDU aggregated packet size is already 4K or 8K, SDIO Multiport
Aggregation feature didn't use to gain much previously.
Now with increased multiport aggregation buffer, we can enable
it for AMSDU packets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently Tx and Rx buffer sizes are 8K and 16K respectively for
all chipsets. We will change them to 32K for SD8897 and 16K for
older chipsets. SD8897 chipset has more SDIO data ports than
older chipsets.
This patch will help to improve throughput numbers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: single byte memset is suspicious.
Swapped 2nd/3rd argument?
This code happens to work because rx_mcs is the first variable
in mcs structure. We should use 'mcs.rx_mcs' here anyway.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using scatter-gather, more descriptor entries get used.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes, due to the race between Rx path and WMI_BA_STATUS_EVENTID WMI event,
few frames may be passed to the stack before reorder buffer allocated.
Then, after BACK establishment, it start getting frames with sequence number ahead of
SSN, and it get interpreted as missing frames. Then, BACK mechanism will wait
for missing frames; data traffic will be stopped. In case of interface configured
for DHCP, this data delay causes DHCP failure.
Relax checking for sequence number; use sequence of 1-st frame handled by the buffer
as SSN for this buffer.
This is work-around, real fix should be done when proper BACK mechanism implemented.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- add pcp_max_assoc_sta to the struct wmi_pcp_start_cmd
- enum for the scan ststus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reshuffle prints to consolidate firmware/hardware information
report upon card init
Convert print for unhandled MISC ISR bits to "debug" - it is
normal situation and not an "error"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use generic TSF timers to trigger powersave state changes based
information from the P2P NoA attribute.
Opportunistic Powersave is not handled, because the driver does not
support powersave at the moment.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation for adding P2P powersave and multi-channel support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use del_timer_sync to ensure that the timer is stopped on all CPUs before
the driver exits.
This change was suggested by Thomas Gleixner.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier i,t,ex;
@@
struct t i = { .remove = ex, };
@@
identifier r.ex;
@@
ex(...) {
<...
- del_timer
+ del_timer_sync
(...)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW should never attempt to perform DMA for unused queues.
For rtl8187se this is ensured by setting a dedicated register at
init time, before enabling TX.
In rtl8180/5 the register is only written at the first TX (because
in rtl8180/5 it serves also to kick DMA for used queues).
This should be enough, but it's worth to add a register write at
init time, before enabling TX.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parentheses are missing around the macro argument, causing the
macro possibly not to work passing certain expressions as
arguments.
This should not cause any issues with current code, however it's
worth to add them, as a good practice, and to eventually avoid
future bugs.
Suggested-by: Dave Kilroy <kilroyd@googlemail.com>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When preparing the bitfield to write to HW register, the high-priority
queue error interrupt bit is set two times, and the beacon queue
TX-OK interrupt is not enabled.
Currently this have no functional impact because the high-priority
queue is not used at all, and the beacon queue is not used yet.
This patch removes high-priority queue bits and it adds the
beacon queue missing bit.
It removes also the management queue bits because it is not used.
This was found by static code analyzer.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8180 driver can handle also rtl8185 and rtl8187SE cards,
however in userspace tools (network manager) it still appares
as "rtl8180".
This might lead the user to think the wrong driver is in use.
This patch changes module name to "rtl818x_pci" that should be
more explanatory.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> [ original patch ]
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement a recv budget so that in cases of high traffic we still allow other
taskets to get processed.
Without this, we can encounter a host of issues during high wireless traffic
reception depending on system load including rcu stall's detected (ARM),
soft lockups, failure to service critical tasks such as watchdog resets,
and triggering of the tx stuck tasklet.
The same thing was proposed previously by Ben:
http://www.spinics.net/lists/linux-wireless/msg112891.html
The only difference here is that I make sure only processed packets are counted
in the budget by checking at the end of the rx loop.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a flush is requested, make sure to clear the descriptor once we've
processed it.
This resolves a hang that will occur if all RX descriptors are full when a
flush is requested.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
static code analysis from cppcheck reports:
[drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:322]:
(error) Uninitialized variable: packet_beacon
packet_beacon is not initialized and hence packet_beacon
contains garbage from the stack, so set it to false.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Stable <stable@vger.kernel.org> [3.10+]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disable beaconing we clear register with beacon and newer set it
back, what make we stop send beacons infinitely.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bump i40e to version 0.3.43 and i40evf to version 0.9.21.
Change-ID: Ice4c715731bfa1dfc12dd45418675a3ba6e08d57
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tweak a for-loop to make it easier to add conditional stats in the future.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the newer i40e_vsi_open() and i40e_vsi_close() in the FDIR VSI
lifetime. This makes sure we're using standard methods for all the
VSI open and close paths. This also fixes a memory leak of the
FDIR queue buffer info structs across a reset.
Change-ID: I1b60a1b08ab923afe4f49810c2c7844d850e19b9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new i40e_vsi_open() for waking VSIs back up in order to
be sure all the standard actions happen.
Change-ID: Ic3479410dd3079733f4951dcea69f101e69e77df
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Abstract out the vsi close actions into a single function so they
can be used correctly for both netdev and non-netdev based VSIs.
Change-ID: I59e3d115fcb20e614a09477281b7787dd340d276
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM updates take some time and are asynchronous actions that signal
their completion with an AdminQ event. This code tracks when there is
an NVM update outstanding and won't allow a new update command until a
completion event is received from the current update.
Change-ID: Ic132fe16bd9dc09b002ed38297a877c1a01553ce
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The flow spec coming in for IPv4 filters is IP_USER_FLOW, which
needed some more info to be communicated up above in order for it
to be displayed correctly.
Change-ID: Ia968238e0d7c4c4df12908ba81f0c4501280f3ec
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the FW workaround to increment the number of msix vectors.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement the net device op for Tx bandwidth setting. Setting the Tx
bandwidth is done by 'ip link set <PF device> vf <VF num> rate <Tx
rate>', with the rate specified in Mbit/sec. The rate setting is
displayed with 'ip link show'.
Change-ID: I4d45dda8320632fdb6ec92c87d083e51070b46ab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a host VMM administrator hoses his VF by assigning a port VLAN after
it is already up and running with implicit permission to set local
VLANs then we print a message warning the host administrator that the
VF driver needs to be reloaded.
In addition we need to knock the VF offline so that it does not continue
to receive traffic not on the port VLAN assigned to it. So we reset the
VF. The VF will cease operation and the administrator will be forced to
unload and reload the VF driver to make it work again.
Change-ID: Iae1ae006b244e74e30a4ee546b3c5fca5cfb40aa
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PREFENA field in the receive host memory cache (RX-HMC)
must be visible in order to be set to 1 at driver init for
best performance.
Change-ID: I16b0bcd84cf56f4b6c938201ff5e954bee5a1992
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the netdev ops to support addition of static FDB entries in the
physical function (PF) MAC/VLAN filter table so that virtual functions
(VFs) can communicate with bridged virtual Ethernet ports such as those
provided by the virtio driver.
Change-ID: Ifbd6817a75074e3b5cdf945a5635f26440bf15df
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
stmmac_config() denies changing the base address and interrupt
parameters, and ignores any other settings from the ifmap parameters,
thus making stmmac_config() useless, remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sxgbe_config() denies changing the base address and interrupt, and
ignores all other 'struct ifmap' members, which means that it is useless
as is, so let's remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpmac_config() refuses changing the base address parameter, and ignores
all other parameters, which means that it is pretty useless as it is, so
let's remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethoc_config() returns -ENOSYS and does not implement anything useful,
let's remove it such that net/core/dev_ioctl.c::dev_ifsioc can return
something meaningful like -EOPNOTSUPP.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature allows multiple channels to be used by each virtual NIC.
It is available on Hyper-V host 2012 R2.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make local functions static, because these are used only in this
file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently broadcasts are handled in network RX context, where
the packets are sent through netif_rx. This means that the number
of macvlans will be constrained by the capacity of netif_rx.
For example, setting up 4096 macvlans practically causes all
broadcast packets to be dropped as the default netif_rx queue
size simply can't handle 4096 skbs being stuffed into it all
at once.
Fundamentally, we need to ensure that the amount of work handled
in each netif_rx backlog run is constrained. As broadcasts are
anything but constrained, it either needs to be limited per run
or moved to process context.
This patch picks the second option and moves all broadcast handling
bar the trivial case of packets going to a single interface into
a work queue. Obviously there also needs to be a limit on how
many broadcast packets we postpone in this way. I've arbitrarily
chosen tx_queue_len of the master device as the limit (act_mirred
also happens to use this parameter in a similar way).
In order to ensure we don't exceed the backlog queue we will use
netif_rx_ni instead of netif_rx for broadcast packets.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic bits from genphy_config_init() instead of implementing
the same functionality again.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables other drivers to call this generic implementation, and then
only do specific details on top of it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add \n at the end of messages where missing, remove all \r.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Time stamping resources are per-interface so there is no need
to keep separate last_rx_timestamp for each Rx ring, move
last_rx_timestamp to the adapter structure.
With last_rx_timestamp inside adapter, ixgbe_ptp_rx_hwtstamp()
inline function is reduced to a single if statement so it is
no longer necessary. If statement is placed directly in
ixgbe_process_skb_fields() fixing likely/unlikely marking.
Checks for q_vector or adapter to be NULL are superfluous.
Comment about taking I/O hit is a leftover from previous design.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RQDPC on i210/i211 is R/W not ReadClear. Clear after reading.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix following compilation warning:
drivers/net/ethernet/intel/e1000e/netdev.c:6238:12: warning
‘e1000e_pm_thaw’ defined but not used [-Wunused-function]
static int e1000e_pm_thaw(struct device *dev)
^
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When changing the interface mtu, the driver starts with a value
that doesn't include VLAN_HLEN. Later tests in the driver
set the rx_buffer_len based on the mtu. As a result, when
the user increases the mtu to 1504 (to support 802.1AD for example),
the driver rx_buffer_len does not change and frames longer
the 1522 bytes are rejected as too long.
Include VLAN_HLEN from the start so that an user mtu greater then
1500 bytes is correctly reflected in the driver rx_buffer_len.
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As reported by Eric Dumazet, the i40e driver was allowing the hardware
to replicate the PSH flag on all segments of a TSO operation.
This patch fixes the first/middle/last TCP flags settings which
makes the TSO operations work correctly.
With this change we are now configuring the CWR bit to only be set
in the first packet of a TSO, so this patch also enables TSO_ECN,
in order to advertise to the stack that we do the right thing
on the wire.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John W. Linville says:
====================
pull request: wireless 2014-04-17
Please pull this batch of fixes intended for the 3.15 stream...
For the mac80211 bits, Johannes says:
"We have a fix from Chun-Yeow to not look at management frame bitrates
that are typically really low, two fixes from Felix for AP_VLAN
interfaces, a fix from Ido to disable SMPS settings when a monitor
interface is enabled, a radar detection fix from Michał and a fix from
myself for a very old remain-on-channel bug."
For the iwlwifi bits, Emmanuel says:
"I have new device IDs and a new firmware API. These are the trivial
ones. The less trivial ones are Johannes's fix that delays the
enablement of an interrupt coalescing hardware until after association
- this fixes a few connection problems seen in the field. Eyal has a
bunch of rate control fixes. I decided to add these for 3.15 because
they fix some disconnection and packet loss scenarios which were
reported by the field. I also have a fix for a memory leak that
happens only with a very new NIC."
Along with those...
Amitkumar Karwar fixes a couple of problems relating to driver/firmware
interactions in mwifiex.
Christian Engelmayer avoids a couple of potential memory leaks in
the new rsi driver.
Eliad Peller provides a wl18xx mailbox alignment fix for problems
when using new firmware.
Frederic Danis adds a couple of missing debugging strings to the
cw1200 driver.
Geert Uytterhoeven adds a variable initialization inside of the
rsi driver.
Luciano Coelho patches the wlcore code to ignore dummy packet events
in PLT mode in order to work around a firmware bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes a problem with dropped jumbo frames after usage of
'ethtool -G ... rx'.
Scenario:
1. ip link set eth0 up
2. ethtool -G eth0 rx N # <- This zeroes rx-jumbo
3. ip link set mtu 9000 dev eth0
The ethtool command set rx_jumbo_pending to zero so any received jumbo
packets are dropped and you need to use 'ethtool -G eth0 rx-jumbo N'
to workaround the issue.
The patch changes the logic so rx_jumbo_pending value is changed only if
jumbo frames are enabled (MTU > 1500).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is for a system with fixed assignments of input and output pins
(various variants of Kontron COMe).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems using mdio-gpio may use active-low gpio pins
(eg with inverters or FETs connected to all or some of the
gpio pins).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies error path and deinit/removal functions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4 driver is triggering schedules while atomic inside
mlx4_en_netpoll:
spin_lock_irqsave(&cq->lock, flags);
napi_synchronize(&cq->napi);
^^^^^ msleep here
mlx4_en_process_rx_cq(dev, cq, 0);
spin_unlock_irqrestore(&cq->lock, flags);
This was part of a patch by Alexander Guller from Mellanox in 2011,
but it still isn't upstream.
Signed-off-by: Chris Mason <clm@fb.com>
cc: stable@vger.kernel.org
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5445eaf309 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, some other platforms, namely the Armada XP GP don't use
SGMII, but a QSGMII connection between the MAC and the PHY, and this
case was not supported by the mvneta driver, which was relying on
configuration put in place by the bootloader. While this works when
the mvneta driver is built-in (because clocks are not gated), it
breaks when mvneta is built as a module, because the clock is gated
(all configuration is lost) and then re-enabled when the mvneta driver
is loaded.
In order to support all of RGMII, SGMII and QSGMII, this commit
reworks how the PHY interface configuration is done, and simplifies
it: it removes the mvneta_port_sgmii_config() and
mvneta_gmac_rgmii_set() functions, which were strange because
mvneta_gmac_rgmii_set() was called in all cases, even for SGMII
configurations. Also, the mvneta_gmac_rgmii_set() function was taking
a boolean as argument, which was always true.
Instead, all the PHY interface configuration logic is moved into the
mvneta_port_power_up() function, in a much simpler 'switch' construct,
with four cases:
- QSGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured in QSGMII. Technically speaking,
configuring the SERDES of the first port would be sufficient, but
it is simpler to do it on all ports.
- SGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured as SGMII.
- RGMII: the RGMIIEn bit in GMAC_CTRL_2 is set. The PCSEn bit is kept
cleared, and no SERDES configuration is done, because RGMII is not
using SERDES lanes.
- other: an error is returned. For this reason, the
mvneta_port_power_up() now returns an int instead of nothing, and
the return value is checked by mvneta_probe().
This has been successfully tested on:
* Armada XP DB, which has two RGMII and two SGMII connections
* Armada XP GP, which uses QSGMII for its four interfaces
* Armada 370 Mirabox, which has two RGMII connections
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCDI command times out (whether or not we find it
completed when we poll), call efx_mcdi_abandon(), which tells
all subsequent MCDI calls to fail-fast, and queues up an FLR.
Because an FLR doesn't lead to receiving any reboot even from
the MC (unlike most other types of reset), we have to call
efx_ef10_reset_mc_allocations.
In efx_start_all(), if a reset (of any kind) is pending, we
bail out.
Without this, attempts to reconfigure (e.g. change mtu) can
cause driver/mc state inconsistency if the first MCDI call
triggers an FLR.
For similar reasons, on EF10, in
efx_reset_down(method=RESET_TYPE_MCDI_TIMEOUT), set the number
of active queues to zero before calling efx_stop_all().
And, on farch, in efx_reset_up(method=RESET_TYPE_MCDI_TIMEOUT),
set active_queues and flushes pending & outstanding to zero.
efx_mcdi_mode_{poll,event}() should not take us out of fail-fast
mode. Instead, this is done by efx_mcdi_reset() after the FLR
completes.
The new FLR reset_type RESET_TYPE_MCDI_TIMEOUT doesn't really
fit into the hierarchy of reset 'scopes' whereby efx_reset()
decides some resets subsume others. Thus, it uses separate logic.
Also, fixed up some inconsistency around RESET_TYPE_MC_BIST,
which was in the wrong place in that hierarchy.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong max fw size was being used and causing false
"too big" errors running ethtool -f.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qlcnic_setup_tss_rss_intr() might enter endless
loop in case pci_enable_msix() contiguously returns a
positive number of MSI-Xs that could have been allocated.
Besides, the function contains 'err = -EIO;' assignment
that never could be reached. This update fixes the
aforementioned issues.
Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.
The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.
Fixes: 8f646c922d ("vxlan: keep original skb ownership")
Reported-by: lucien xin <lucien.xin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes when command timeout occurs due to a firmware or
hardware bug, there may be some synchronous commands in command
queue. These commands are never downloaded to firmware causing
hung task warnings. This patch replaces wait_event_interruptible
call with wait_event_interruptible_timeout to fix the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During extended scan, SCAN report event is always followed by
command response. Sometimes It is observed that command response
is processed before SCAN report which leads to a crash, because
current command node is cleared while handling the response.
This patch makes sure that driver's main thread gives priority
to events over command responses.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In cosa driver, udelay with more than 20000 may cause __bad_udelay.
Use msleep for instead.
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __at86rf230_read_subreg function don't mask and shift register
contents which it should do. This patch adds the necessary masks and
shift operations in this function.
Since we have csma support this can make some trouble on state changes.
Since CSMA support turned on some bits in the TRX_STATUS register that
used to be zero, not masking broke checking of the TRX_STATUS field
after commanding a state change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVDD regulator is only enabled when the RF section is active TX_ON
(PLL_ON) state. Since commit 7dcbd22a97
("ieee802154: ensure that first RF212 state comes from TRX_OFF").
We are in TRX_OFF state at the time at86rf230_hw_init is run.
Note that this test would only fail in case of a severe hardware
malfunction (faulty/shorted power supply, etc.) so it wasn't all that
useful in the first place.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cadence ethernet chipsets are only used on specific ARM
architectures. Add Kconfig dependencies so that drivers for these
chipsets are only buildable on the relevant architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware needs the local device mac address to support hw loopback for
rdma loopback connections.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fields are missing from the event mailbox
struct definitions, which cause issues when
trying to handle some events.
Add the missing fields in order to align the
struct size (without adding actual support
for the new fields).
Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: stable@vger.kernel.org # 3.14+
Fixes: 028e724 ("wl18xx: move to new firmware (wl18xx-fw-3.bin)")
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a potential memory leak in the error path of function
rsi_send_auto_rate_request(). In case memory allocation for array
'selected_rates' fails, the error path exits and leaves the previously
allocated skb in place. Detected by Coverity: CID 1195575.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This array is used in debug string to display cw1200_link_status
defined in drivers/net/wireless/cw1200/cw1200.h.
Add missing strings for CW1200_LINK_RESET and CW1200_LINK_RESET_REMAP.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes the firmware sends a dummy packet event while we are in PLT
mode. This doesn't make sense, it's a firmware bug. Fix this by
ignoring dummy packet events when we're PLT mode.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a potential memory leak in function rsi_set_channel() that is used to
program channel changes. The channel check block for the frequency bands
directly exits the function in case of an error, thus leaving an already
allocated skb unreferenced. Move the checks above allocating the skb.
Detected by Coverity: CID 1195576.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/rsi/rsi_91x_core.c: In function ‘rsi_core_determine_hal_queue’:
drivers/net/wireless/rsi/rsi_91x_core.c:91: warning: ‘ii’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
o While disabling SR-IOV when VFs are assigned to VMs causes host crash
so return -EPERM when user request to disable SR-IOV using pci sysfs in
case of VFs are assigned to VMs.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Application expect vNIC number as the array index but driver interface
return configuration in array index form.
o Pack the vNIC information array in the buffer such that application can
access it using vNIC number as the array index.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear older PVID before adding a newer PVID to the eSwicth port
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not read max rings count from qlcnic_get_nic_info(). Use driver defined
values for 82xx adapters. In case of 83xx adapters, use minimum of firmware
provided and driver defined values.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o INIT_NIC_FUNC should be first mailbox sent. Sending DCB capability and
parameter query commands after that command.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o AEN event was being received before initializing delayed_work struct
and handlers for it. This was resulting in crash. This patch fixes it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the EEH error recovery path, when a permanent failure occurs,
we clean up adapter structure (i.e. destroy queues etc) by calling
be_clear() and return PCI_ERS_RESULT_DISCONNECT.
After this the stack tries to remove device from bus and calls
be_remove() which invokes netdev_unregister()->be_close().
be_close() operating on destroyed queues results in a
NULL dereference.
This patch fixes this problem by introducing a flag to keep track
of the setup state.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_close() currently waits for a max of 200ms to receive all pending
TX compls. This timeout value was roughly calculated based on 10G
transmission speeds and the TX queue depth. This timeout may not be
enough when the link is operating at lower speeds or in multi-channel/SR-IOV
configs with TX-rate limiting setting.
It is hard to calculate a "proper timeout value" that works in all
configurations. This patch solves this problem by continuing to reap
TX completions till the HW is completely silent for a period of 10ms or
a HW error is detected.
v2: implements the new scheme (as suggested by David Laight) instead of
just waiting longer than 200ms for reaping all completions.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix in commit [1] is not sufficient since a deferred VF initialization
could happen after pci_enable_sriov() is finished, but before the PF is
fully initialized.
Need to prevent VFs from initializing till the PF is fully ready and
comm channel is operational.
[1] - 9798935 "net/mlx4_core: mlx4_init_slave() shouldn't access comm
channel before PF is ready"
CC: Stuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP isn't enabled, bnx2_suspend/resume are unused; don't
build them when they aren't used.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e3a8786c10. While
this commit allows to use the mvneta driver as a module on some
configurations, it breaks other configurations even if mvneta is used
built-in.
This breakage is due to the fact that on some RGMII platforms, the PCS
bit has to be set, and on some other platforms, it has to be
cleared. At the moment, we lack informations to know exactly the
significance of this bit (the datasheet only says "enables PCS"), and
so we can't produce a patch that will work on all platforms at this
point. And since this change is breaking the network completely for
many users, it's much better to revert it for now. We'll come back
later with a proper fix that takes into account all platforms.
Basically:
* Armada XP GP is configured as RGMII-ID, and needs the PCS bit to be
set.
* Armada 370 Mirabox is configured as RGMII-ID, and needs the PCS bit
to be cleared.
And at the moment, we don't know how to make the distinction between
those two cases. One hint is that the Armada XP GP appears in fact to
be using a QSGMII connection with the PHY (Quad-SGMII), but
configuring it as SGMII doesn't work, while RGMII-ID works. This needs
more investigation, but in the mean time, let's unbreak the network
for all those users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Alexander Reuter <Alexander.Reuter@gmx.net>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=73401
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_match_id() just match the static pci_device_id, which may return NULL if
someone binds the driver to a device manually using
/sys/bus/pci/drivers/.../new_id.
This patch wrap up a helper function __mlx4_remove_one() which does the tear
down function but preserve the drv_data. Functions like
mlx4_pci_err_detected() and mlx4_restart_one() will call this one with out
releasing drvdata.
Fixes: 97a5221 "net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset".
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Amir Vadai <amirv@mellanox.com>
CC: Jack Morgenstein <jackm@dev.mellanox.co.il>
CC: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
7000 device series have a fix for this hardware feature.
Stop disabling it, and get an improvement in Tx throughput.
This feature allows the scheduler to fetch more frames on
the fly while an A-MPDU is being built - which means that
we can get larger A-MPDU. This, of course, give an
improvement in the Tx throughput.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver can enable uAPSD and specify some of its related parameters.
This patch organizes this logic in a separate function.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
bail out from the suspend/resume callbacks if
d0i3 is used.
declare support for ANY wowlan trigger (i.e.
normal operation).
On resume, we shouldn't execute the d0i3 exit
flow (which might disconnect stations, etc.)
until mac80211 was resumed.
Add new flags to indicate we are in suspend,
and call the pending exit work on resume.
Since the resume flow can take some time, add
a new EXIT_WORK reference type to prevent going
back to d0i3 at this stage.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch enables Energy Based Scan (EBS) - intended to detect energy
on 5 GHz band channels. Passive scan on this band takes up to 2.64 sec
assuming 110mSec per-channel * 24 channels. EBS is designed to detect
energy on channels with intensive Wifi activity as well as those where
only beacons are transmitted. EBS completes sampling all channels within
shortest beacon frame transmission time. Total EBS duration is about 100
msec (typical beacon interval).
Detecting Wifi activity on 5 GHz band channels can significantly reduce
scan duration thus saving time and power. EBS failure reported by FW
disables EBS for current connection. It is re-enabled upon new
connection attempt on any WLAN interface.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Calling iwl_send_bt_init_conf for INIT firmware is not a
problem, and calling iwl_send_bt_prio_tbl from
iwl_send_bt_init_conf allows us to prepare for new API.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The BT Coex API underwent a minor backward compatible API
change.
We now need to set an invalid value in the override fields.
While at it, add kerneldoc comments on the fields in the
command.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is really not needed. This is a remainder from a C99
initialiser.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares have this flag set.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares have this flag set.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares have this flag set.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares have this flag set.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A few entries were wrong and this caused throughput issues.
Cc: <stable@vger.kernel.org> [3.13+]
Fixes: dac94da8db ("iwlwifi: mvm: new BT Coex API")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The per rate stats should be cleared when aggregation state changes
to avoid making rate scale decisions based on throughput figures which
were collected prior to the aggregation state change and are now stale.
While at it make sure any clearing of the per rate stats will get logged.
Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't search columns which are unlikely to succeed as previous
columns searched with less aggressive modulation failed.
Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow switching back to legacy Tx columns so we'll stop doing
HT/VHT in case we're far from the AP. Stop active aggregation when
making a deciding to stay in a legacy column.
Despite having low legacy rates in the LQ table lower entries
it doesn't help much in case we're doing aggregations as the
aggregation was being transmitted in the initial rate of the table.
This should help traffic stalls when far from the AP.
Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After being idle for a long time (>5sec) the rs statistics
will be stale so we prefer to reset rs and start from legacy
rates again. This gives better results when the attenuation
increased signficantly (e.g. we got further from the AP) and
after a while we start Tx
Note that the first Tx after the idle period will still go out
in the old modulation and rate but this seemed a simpler approach
compared to adding a timer or modifying mac80211 for this.
The negative impact is negligble as we'll recover quickly.
Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change the down/upscale decision logic a bit to be based
on different success ratio thresholds. This fixes the implementation
compared to the rate scale algorithm which was planned to yield
optimal results. Also fix a case where a lower rate wasn't explored
despite being a potential for better throughput.
While at it rewrite rs_get_rate_action to be more clear and clean.
Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The selection of the max expected throughput for a column
didn't take into account the maximal allowed rate for the current
peer. This can cause unnecessary switches during the search cycle
to columns which have no chance of beating the current throughput.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This firmware is not supported any more.
A few code paths specific to old firmware can be removed.
We can now assume that a few TLV flags are always set since
we won't load firmware that didn't support the corresponding
features. This will be done in a separate patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
While the scan_cmd should really be allocated in init (and
we do fail init in case the allocation failed), it doesn't
mean we should lock up the machine if something really bad
happened.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Collect accumulated stats of tx attempts and successes
per rate and column for debugging purposes.
These stats can be read via debugfs file drv_tx_stats
and can also be reset by writing to this file.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
rcu_assign_pointer() ensures that the initialization of a structure is
carried out before storing a pointer to that structure. However, in the
case that NULL is assigned there's no structure to initialize so using
RCU_INIT_POINTER instead is safe and more efficient.
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
[rewrite commit log]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware doesn't support broadcast filtering on P2P
client. Trying to enable it makes the firmware assert.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When NIC is exiting from thermal throttling state (i.e. after
heating and then cooling down), tx-backoff values are assigned
to be zero, instead of being restored to the minimal value. Fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When NIC exit thermal throttling while having minimal tx-backoff
restriction, the warning message that indicate about that state
won't show up. Fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The Rx FIFO includes valuable data - dump it when the FW
asserts. Also - free the SRAM and Rx FIFO when we create
the file, and don't collect new SRAM / Rx FIFO if the
previous file hasn't been collected through debugfs yet.
Also - add a comment to saying that the ASSERT output should
not be modified since we have automatic scripts that monitor
this output.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This must not happen - otherwise we might keep flushing
forever.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will be used later to flush / wait for queues that are
related to a specific vif.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Now that mac80211 calls pre_rcu_remove and we set the
fw_id_to_mac_id pointer to -ENOENT before the station is
removed, we don't need to set fw_id_to_mac_id to -EINVAL
when the station is really removed.
Leave fw_id_to_mac_id to be -ENOENT which will let the
drain worker (iwl_mvm_sta_drained_wk) know that this station
is not to be drained.
We don't need to drain this station since it is our AP in
managed mode and we flush all its frames synchronously
anyway.
Setting the AP station to -EINVAL could lead to confusion
since internal stations are also reserved with -EINVAL,
this confusion showed up in the logs as:
Drained sta 0, but it is internal?
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware tells us if an Rx packet was beamformed or not.
Propagate this data to mac80211's rx_status.vht_flags.
The main user of this data is the radiotap header.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This define is related to the firmware packaging and is
needed by more than one transport.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Besides the different allocation flags, they are really
the same. Pass the gfp_t flags as a parameter, and unify
them.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Similar to the recent RX queue patch, this changes the need_update
handling for the TX queues to be clearer and only done when needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When updating the write pointer, the TX queue should be locked
to get consistent state, fix that in the interrupt handler.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of using u8 to hold logic values, use bool.
Also fix a comment, the return value is no longer relevant.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When shadow registers are enabled, then need_update never needs
to be set, so move the need_update handling into the function
that really needs to do it (iwl_pcie_rxq_inc_wr_ptr) and also
separate the check when it woke up. While at it, convert it to
bool.
This also clarifies the locking and means the irq_lock needs to
no longer be held for any such updates.
The irq_lock also doesn't have to be held for restocking since
everything else locks the RX queue properly, so remove that and
finally disentangle the two locks entirely so there aren't any
dependencies between the two left.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use the new NAPI infrastructure added to mac80211 to get
GRO. We don't really implement NAPI since we don't have
a real poll function and we never schedule a NAPI poll.
Instead of this, we collect all the packets we got from a
single interrupt and then call napi_gro_flush().
This allows us to benefit from GRO. In half duplex medium
like WiFi, its main advantage is that it reduces the number
of TCP Acks, hence improving the TCP Rx performance.
Since we call the Rx path with a spinlock held, remove
the might_sleep mention from the op_mode's API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ido Yariv <ido@wizery.com>
[Squash different patches and rewrite the commit message]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow fixing the tx power reduction through debugfs
file.
The change doesn't take affect immediately, but
will be considered the next time tpc is evaluated.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Implement Adaptive Tx Power Control algorithm.
ATPC basically tries to decrease the tx power
as much as possible while the throughput is
not being hurt.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I forgot to send the new Look Up Table to the firmware and
I also forgot to free the command which is kzalloc'ed.
This code is relevant for 7265 device only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
mimo_delim was always set to 0 instead of pointing to
the first SISO entry after MIMO rates.
This can cause keep transmitting in MIMO even when we shouldn't.
For example when the peer is requesting static SMPS.
Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we have no beacon data before association, delay smart FIFO
enablement until after we have this data.
Not doing so can cause association failures in extremely silent
environments (usually only a shielded box/room) as beacon RX is
not sent to the host immediately, and then the association time
event ends without the host receiving any beacon even though it
was on the air - it's just stuck on the FIFO.
Cc: <stable@vger.kernel.org> [3.14]
Fixes: 1f3b0ff8ec ("iwlwifi: mvm: Add Smart FIFO support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull yet more networking updates from David Miller:
1) Various fixes to the new Redpine Signals wireless driver, from
Fariya Fatima.
2) L2TP PPP connect code takes PMTU from the wrong socket, fix from
Dmitry Petukhov.
3) UFO and TSO packets differ in whether they include the protocol
header in gso_size, account for that in skb_gso_transport_seglen().
From Florian Westphal.
4) If VLAN untagging fails, we double free the SKB in the bridging
output path. From Toshiaki Makita.
5) Several call sites of sk->sk_data_ready() were referencing an SKB
just added to the socket receive queue in order to calculate the
second argument via skb->len. This is dangerous because the moment
the skb is added to the receive queue it can be consumed in another
context and freed up.
It turns out also that none of the sk->sk_data_ready()
implementations even care about this second argument.
So just kill it off and thus fix all these use-after-free bugs as a
side effect.
6) Fix inverted test in tcp_v6_send_response(), from Lorenzo Colitti.
7) pktgen needs to do locking properly for LLTX devices, from Daniel
Borkmann.
8) xen-netfront driver initializes TX array entries in RX loop :-) From
Vincenzo Maffione.
9) After refactoring, some tunnel drivers allow a tunnel to be
configured on top itself. Fix from Nicolas Dichtel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vti: don't allow to add the same tunnel twice
gre: don't allow to add the same tunnel twice
drivers: net: xen-netfront: fix array initialization bug
pktgen: be friendly to LLTX devices
r8152: check RTL8152_UNPLUG
net: sun4i-emac: add promiscuous support
net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
net: ipv6: Fix oif in TCP SYN+ACK route lookup.
drivers: net: cpsw: enable interrupts after napi enable and clearing previous interrupts
drivers: net: cpsw: discard all packets received when interface is down
net: Fix use after free by removing length arg from sk_data_ready callbacks.
Drivers: net: hyperv: Address UDP checksum issues
Drivers: net: hyperv: Negotiate suitable ndis version for offload support
Drivers: net: hyperv: Allocate memory for all possible per-pecket information
bridge: Fix double free and memory leak around br_allowed_ingress
bonding: Remove debug_fs files when module init fails
i40evf: program RSS LUT correctly
i40evf: remove open-coded skb_cow_head
ixgb: remove open-coded skb_cow_head
igbvf: remove open-coded skb_cow_head
...
ntb_netdev, a typo, and a leak of msix entries in the error path.
Clean ups of the event handling logic, as well as a overall style
cleanup. Finally, the driver was converted to use the new
pci_enable_msix_range logic (and the refactoring to go along with it).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=vDei
-----END PGP SIGNATURE-----
Merge tag 'ntb-3.15' of git://github.com/jonmason/ntb
Pull PCIe non-transparent bridge fixes and features from Jon Mason:
"NTB driver bug fixes to address issues in list traversal, skb leak in
ntb_netdev, a typo, and a leak of msix entries in the error path.
Clean ups of the event handling logic, as well as a overall style
cleanup. Finally, the driver was converted to use the new
pci_enable_msix_range logic (and the refactoring to go along with it)"
* tag 'ntb-3.15' of git://github.com/jonmason/ntb:
ntb: Use pci_enable_msix_range() instead of pci_enable_msix()
ntb: Split ntb_setup_msix() into separate BWD/SNB routines
ntb: Use pci_msix_vec_count() to obtain number of MSI-Xs
NTB: Code Style Clean-up
NTB: client event cleanup
ntb: Fix leakage of ntb_device::msix_entries[] array
NTB: Fix typo in setting one translation register
ntb_netdev: Fix skb free issue in open
ntb_netdev: Fix list_for_each_entry exit issue
This patch fixes the initialization of an array used in the TX
datapath that was mistakenly initialized together with the
RX datapath arrays. An out of range array access could happen
when RX and TX rings had different sizes.
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000, e1000e, igb, igbvf, ixgb, ixgbe,
ixgbevf and i40evf.
Mark fixes an issue with ixgbe and ixgbevf by adding a bit to indicate
when workqueues have been initialized. This permits the register read
error handling from attempting to use them prior to that, which also
generates warnings. Checking for a detected removal after initializing
the work queues allows the probe function to return an error without
getting the workqueue involved. Further, if the error_detected
callback is entered before the workqueues are initialized, exit without
recovery since the device initialization was so truncated.
Francois Romieu provides several patches to all the drivers to remove
the open coded skb_cow_head.
Jakub Kicinski provides a fix for igb where last_rx_timestamp should be
updated only when Rx time stamp is read.
Mitch provides a fix for i40evf where a recent change broke the RSS LUT
programming causing it to be programmed with all 0's.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Stübner