L/R channel will be switched if under/over flow error happen on
Renesas R-Car sound device by the HW bugs. Then, HW restart is required
for salvage. This patch add salvage support for SRC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current R-Car sound SSI PIO/DMA mode are using interrupt.
it is no longer "xxx_pio_xxx", rename it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sound data needs to be sent to R-Car sound SSI when playback.
But, there are 2 interfaces for it.
1st is SSITDR/SSIRDR which are mapped on SSI.
2nd is SSIn_BUSIF which are mapped on SSIU.
2nd SSIn_BUSIF is used when DMA transfer,
and it is always used if sound data came from via SRC.
But, we can use it when SSI+DMA case too.
(Current driver is assuming 1st SSITDR/SSIRDR for it)
2nd SSIn_BUSIF can be used as FIFO.
This is very helpful/useful for SSI+DMA.
But DMA address / DMA ID are not same between 1st/2nd cases.
This patch care about these settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds DVC (Digital Volume Controller)
support which is member of CMD unit.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now, all platform is using new style rsnd_dai_platform_info.
Keeping compatibility is no longer needed.
We can cleanup code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound has SCU unit which has SRC/CTU/MIX/DVC,
and current rsnd driver has scu.c and scu module.
Current scu.c has SRC support only.
My first concept was control these feature on scu.c
but, it become difficult and un-understandable now.
This patch rename scu to src
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current rsnd driver is assuming that SCU/SRU ID is
same as SSIU/SSI ID, because Gen1 can't select it.
But, Gen2 can select it.
The SCU/SRU/SSIU/SSI pair depends on the platform.
This patch get correct SCU ID from platform info.
To keep compatible, it still assuming SCU ID = SSI ID
if platform doesn't have info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound DAI consists from SSI/SCU/SSIU/SRU...
Current R-Car sound DAI is decided from these settings,
but it is intuitively unclear, and is not good design for DT support.
This patch adds new rsnd_dai_platform_info to solve this issue.
But now, many platform is using this driver without
rsnd_dai_platform_info.
So, this patch still supports DAI settings via SSI to keep compatible.
It will be removed in next Linux version.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound Gen2 has SRC (= Sampling Rate Converter)
which needs 2 DMAC.
The data path image when you use SRC on Gen2 is
[mem] -> Audio-DMAC -> SRC -> Audio-DMAC-peri-peri -> SSIU -> SSI
This patch support SRC and DMAEnine.
It is tested on R-Car H2 Lager board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas Chip is supporting multi pin sound,
but the HW setting is very difficult and confusable.
But driver is supporting it halfway.
Remove SYNC option at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This branch is reducing in size for every release since most board-related
changes have started happening in devicetrees now. Still, we have some things
going on here.
* Renesas platforms are still adding a bit more legacy device support, something
that should trail off shortly as they move to full DT.
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a handful of old
code is being removed here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wLdE
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch is reducing in size for every release since most
board-related changes have started happening in devicetrees now.
Still, we have some things going on here.
* Renesas platforms are still adding a bit more legacy device
support, something that should trail off shortly as they move to
full DT
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a
handful of old code is being removed here"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: dts: OMAP2: fix interrupt number for rng
ARM: dts: Split omap3 pinmux core device
ARM: dts: Add omap specific pinctrl defines to use padconf addresses
ARM: bcm2835: bcm2835_defconfig updates
ARM: msm_defconfig: Enable restart driver
defconfig: msm_defconfig: Enable CONFIG_ARCH_MSM8974
ARM: msm: Add support for APQ8074 Dragonboard
ARM: exynos_defconfig: Enable S2MPS11 voltage regulator
ARM: tegra: Enable DRM panel support
ARM: shmobile: mackerel: Fix USBHS pinconf entry
ARM: shmobile: Let Koelsch multiplatform boot with Koelsch DTB
ARM: shmobile: Let Lager multiplatform boot with Lager DTB
ARM: shmobile: Remove non-multiplatform Koelsch reference support
ARM: shmobile: Remove non-multiplatform Lager reference support
ARM: shmobile: koelsch-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: lager-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: koelsch-reference: Remove duplicate CCF initialization
ARM: shmobile: lager-reference: Enable multiplaform kernel support
ARM: shmobile: armadillo: Set backlight enable GPIO
ARM: shmobile: Koelsch: add Ether support
...
Conflicts:
arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c
This patch adds SRC support to Renesas sound driver.
SRC converts sampling rate between codec <-> cpu.
It needs special codec chip,
or very simple DA/AD converter to use it.
This patch was tested via ak4554 codec,
and supports Gen1 only at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
92eba04e4b
(ASoC: rcar: remove RSND_SSI_CLK_FROM_ADG) removed
RSND_SSI_CLK_FROM_ADG, it is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current SSI needs RSND_SSI_DEPENDENT flag to
decide dependent/independent mode.
And SCU needs RSND_SCU_USE_HPBIF flag
to decide HPBIF is enable/disable.
But these 2 means same things.
This patch adds new rsnd_scu_hpbif_is_enable()
function, and merges above methods.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current rcar is using rsnd_is_gen1/gen2() to checking its
IP generation, but it needs data mask.
This patch fixes it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds BUSIF support for R-Car sound DMAEngine transfer.
The sound data will be transferred via FIFO which can cover blank time
which will happen when DMA channel is switching.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds DMAEngine transfer on SSI.
But, it transfers sound data from memory to SSI directly
without using HPBIF at this time.
It will be updated soon
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current rsnd driver is using struct rsnd_dai_platform_info
so that indicate sound DAI information (playback/capture SSI ID).
But, SSI settings were also required separately.
Thus, platform settings was very un-understandable.
This patch adds dai_id to SSI
settings, and removed rsnd_dai_platform_info.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
As 1st protype, this patch adds SSI feature on this driver.
But, it is PIO sound playback support only at this point.
The DMA transfer, and capture feature will be supported in the future
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
This patch adds ADG feature which controls sound clock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
This patch adds SCU feature on this driver.
But, it defines SCU style only, does nothing at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
The main difference between Gen1 and Gen2 are
1) register offset, 2) data path
In order to control Gen1/Gen2 by same method,
this patch adds gen.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuits are different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2).
(Actually, there are many difference in Generation1 chips)
Basically, for the future, Renesas R-Car series will use
Gen2 style sound circuit, but driver should care Gen1 also.
The main differences between Gen1 and Gen2 peripheral
are 1) register offset, 2) data path.
This patch adds basic (core) feature for R-Car
series sound driver as prototype
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Kuninori Morimoto