The current virtio block's naming algorithm just supports 18278
(26^3 + 26^2 + 26) disks. If there are more virtio blocks,
there will be disks with the same name.
Based on commit 3e1a7ff8a0, add
a function "virtblk_name_format()" for virtio block to support mass
of disks naming.
Notes:
- Our naming scheme is ugly. We are stuck with it
for virtio but don't use it for any new driver:
new drivers should name their devices PREFIX%d
where the sequence number can be allocated by ida
- sd_format_disk_name has exactly the same logic.
Moving it to a central place was deferred over worries
that this will make people keep using the legacy naming
in new drivers.
We kept code idential in case someone wants to deduplicate later.
Signed-off-by: Ren Mingxin <renmx@cn.fujitsu.com>
Acked-by: Asias He <asias@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
commit ea5d404655
broke build for the vhost test module used
by tools/virtio. Fix it up.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This fixes a resume regression introduced in
commit 7dd4906586
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Mar 21 10:48:18 2012 +0000
drm/i915: Mark untiled BLT commands as fenced on gen2/3
which fixed fencing tracking for untiled blt commands.
A side effect of that patch was that now also untiled objects have a
non-zero obj->last_fenced_seqno to track when a fence can be set up
after a pipelined tiling change. Unfortunately this was only cleared
by the fence setup and teardown code, resulting in tons of untiled but
inactive objects with non-zero last_fenced_seqno.
Now after resume we completely reset the seqno tracking, both on the
driver side (by setting dev_priv->next_seqno = 1) and on the hw side
(by allocating a new hws page, which contains the seqnos). Hilarity
and indefinite waits ensued from the stale seqnos in
obj->last_fenced_seqno from before the suspend.
The fix is to properly clear the fencing tracking state like we
already do for the normal gpu rendering while moving objects off the
active list.
Reported-and-tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This removes the HOTPLUG_PCI_PCIE dependency on the driver and makes it
depend on PCI.
Cc: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If a bitmap is added while the array is active, it is possible
for bitmap_daemon_work to run while the bitmap is being
initialised.
This is particularly a problem if bitmap_daemon_work sees
bitmap->filemap as non-NULL before it has been filled in properly.
So hold bitmap_info.mutex while filling in ->filemap
to prevent problems.
This patch is suitable for any -stable kernel, though it might not
apply cleanly before about 3.1.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
If r1bio->sectors % 8 != 0,then the memcmp and a later
memcpy will omit the last bio_vec.
This is suitable for any stable kernel since 3.1 when bad-block
management was introduced.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
bitmap_new_disk_sb() would still create V3 bitmap superblock
with host-endian layout.
Perhaps I'm confused, but shouldn't bitmap_new_disk_sb() be
creating a V4 bitmap superblock instead, that is portable,
as per comment in bitmap.h?
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The struct exynos_drm_manager has to exist for exynos drm sub driver
using encoder and connector. If it isn't NULL to member of struct
exynos_drm_subdrv, will create encoder and connector else will not. And
the is_local member also doesn't need.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The mixer driver and hdmi driver have each operation callback functions
and they is registered to hdmi common driver. Their struct names in hdmi
common driver include display, manager and overlay. It confuses to
appear whose operation and two driver cannot register same operation
callback functions at the same time. Use their struct names to driver
name.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The default_win member in struct mixer_context isn't change its value
after initialized to 0, so it's better using to define.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI_OVERLAY_NUMBER is specific of mixer driver and be used "windows
layer" term in exynos user manaual, so rename it.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Some members in struct mixer_context aren't used and the define
HDMI_OVERLAY_NUMBER is unused in hdmi driver, remove them.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When the void pointer type variable is assigned to the specific pointer
type variable, don't need to do type conversion.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
If, in drivers/input/misc/da9052_onkey.c::da9052_onkey_probe(), the
call to either kzalloc() or input_allocate_device() fails then we will
return -ENOMEM from the function without freeing the other allocation
that may have succeeded, thus we leak either the memory allocated for
'onkey' or the memory allocated for 'input_dev' if one succeeds and
the other fails.
Fix that by jumping to the 'err_free_mem' label at the end of the
function that properly cleans up rather than returning directly.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit b519508298.
The reason for this revert is that making the frequency verification
preemptible and interruptible is not working reliably. Michaels
machine failed to use PM-timer with the message:
PM-Timer running at invalid rate: 113% of normal - aborting.
That's not a surprise as the frequency verification does rely on
interrupts being disabled. With a async scheduled thread there is no
guarantee to achieve the same result. Also some driver might fiddle
with the CTC channel 2 during the verification period, which makes the
result even more random and unpredictable.
This can be solved by using the same mechanism as we use in the
deferred TSC validation code, but that only will work if we verified a
working HPET _BEFORE_ trying to do the PM-Timer lazy validation.
So for now reverting is the safe option.
Bisected-by: Michael Witten <mfwitten@gmail.com>
Cc: Arjan van de Ven <arjanvandeven@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <alpine.LFD.2.02.1204112303270.2542@ionos>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
kernels used to just return something, even if the underlying value was
out-of-bounds, while 3.4-rc1 returned EINVAL to userspace. This breaks
some applications that check for the error, so go back to the old
behavior.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABCAAGBQJPhb1PAAoJEENa44ZhAt0heLgQAI8qrLIBUyHzzfmwMYE7c+fq
PWnXo4ZT6YLht2l7PPxZOGUYtW2FSR9uneuTRozCAyLWmMNvfHNQTIXZQpP7N4zA
Ql3SkI08962Hhdgrd3pF9/Qv5BWrUgOEfpts4kJ3uIafG/gNCAwuEUOjFl7N9FYA
6sGsa9uEm1KgYzH97Kn79z9qnbZYNdwsiuuwvG9gpNaW5m0zdysowheC+JMGDld/
1Y4fMGbv3AO4K+vv8jFtkVvd2F6fa2qDlZ3cP0+o+EfQGWzdpf/BL+sK5j6R0gAw
OFByHvZTXMK9daMOueG+s+4teYe85PFgriugA++UCTb/JAIqfQi4bwcFm3Iv1uCL
zfIsmo6Q15KXda3xp/sUUcI97/IMFz82f8ow9LwjcfPxz1+F/OjKA/jdCw1LX7h/
LizVLdvNp/IoQ76/0jfV0isf4BZbT1OaheMM0vDW9yTGbelNwds1KbrYyhe1IQwV
Zjv183BLytoEzfP/1bD3y88nsgxWwqoekZ6QDca/zq4nYyf1TPerOL+wESOqsNha
K5JtnZWFllf6dYSyLNlysfIC4RlBc/6dhJQYaCvVbI1/I3a+zLsnuFJDlGLlxyf7
G2OedlXLggcb9RSiJxb31aQ4BS7nOVEBvnjIIo8hz31xD2Gz9PGuTdl/HOdtpr/k
5l2bgFfrtmeClzhVjhHq
=xYF8
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Fix a regression in the /sys/class/infiniband/.../rate attribute --
old kernels used to just return something, even if the underlying
value was out-of-bounds, while 3.4-rc1 returned EINVAL to userspace.
This breaks some applications that check for the error, so go back to
the old behavior."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Don't return EINVAL from sysfs rate attribute for invalid speeds
IB/mlx4: Don't return an invalid speed when a port is down
People have been getting confused and thinking this is a runtime control.
Cc: stable@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In https://bugzilla.kernel.org/show_bug.cgi?id=42976, a system with driver
rtl8192se used as an AP suffers from "Out of SW-IOMMU space" errors. These
are caused by the DMA buffers used for beacons never being unmapped.
This bug was also reported at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/961618
Reported-and-Tested-by: Da Xue <da@lessconfused.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current version of rtlwifi for USB operations uses kmalloc to
acquire a 32-bit buffer for each read of the device. When
_usb_read_sync() is called with the rcu_lock held, the result is
a "sleeping function called from invalid context" BUG. This is
reported for two cases in https://bugzilla.kernel.org/show_bug.cgi?id=42775.
The first case has the lock originating from within rtlwifi and could
be fixed by rearranging the locking; however, the second originates from
within mac80211. The kmalloc() call is removed from _usb_read_sync()
by creating a ring buffer pointer in the private area and
allocating the buffer data in the probe routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [This version good for 3.3+ - different patch for 3.2 - 2.6.39]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull media fixes from Mauro Carvalho Chehab:
- dvb core: there is a regression found when used with xine. For
whatever unknown reason, xine (and xine-lib clients) wants that the
frontend to tell what frequency he is using even before the PLL lock
(or at least, it expects a non-zero frequency).
On DVB, the frequency is only actually known after a frequency
zig-zag seek, done by the DVB core. Anyway, the fix was trivial.
That solves Fedora BZ#808871.
- ivtv: fix a regression when selecting the language channel
- uvc: fix a race-related crash
- it913x: fixes firmware loading
- two trivial patches (a dependency issue at a radio driver at sound
Kconfig, and a warning fix on dvb).
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] uvcvideo: Fix race-related crash in uvc_video_clock_update()
[media] Drivers/media/radio: Fix build error
[media] dvb_frontend: fix compiler warning
[media] it913x: fix firmware loading errors
[media] ivtv: Fix AUDIO_(BILINGUAL_)CHANNEL_SELECT regression
[media] dvb_frontend: regression fix: userspace ABI broken for xine
Re-define XHCI_LEGACY_DISABLE_SMI and used it in right way. All SMI enable
bits will be cleared to zero and flag bits 29:31 are also cleared to zero.
Other bits should be presvered as Table 146.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The caller is allowed to specify the GFP flags for these functions.
We should prefer their flags unless we have good reason. For
example, if we take a spin_lock ourselves we'd need to use
GFP_ATOMIC. But in this case it's safe to use the callers GFP
flags.
The callers all pass GFP_ATOMIC here, so this change doesn't affect
how the kernel behaves but we may add other callers later and this
is a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The suspend operation of VIA xHCI host have some issues and
hibernate operation works fine, so The XHCI_RESET_ON_RESUME
quirk is added for it.
This patch should base on "xHCI: Don't write zeroed pointer
to xHC registers" that is released by Sarah. Otherwise, the
host system error will ocurr in the hibernate operation
process.
This should be backported to stable kernels as old as 2.6.37,
that contain the commit c877b3b2ad
"xhci: Add reset on resume quirk for asrock p67 host".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When the Seagate Goflex USB3.0 device is attached to VIA xHCI
host, sometimes the device will downgrade mode to high speed.
By the USB analyzer, I found the device finished the link
training process and worked at superspeed mode. But the device
descriptor got from the device shows the device works at 2.1.
It is very strange and seems like the device controller of
Seagate Goflex has a little confusion.
The first 8 bytes of device descriptor should be:
12 01 00 03 00 00 00 09
But the first 8 bytes of wrong device descriptor are:
12 01 10 02 00 00 00 40
The wrong device descriptor caused the initialization of mass
storage failed. After a while, the device would be recognized
as a high speed device and works fine.
This patch will warm reset the device to fix the issue after
finding the bcdUSB field of device descriptor isn't 0x0300
but the speed mode of device is superspeed.
This patch should be backported to kernels as old as 3.2, or ones that
contain the commit 75d7cf72ab "usbcore:
refine warm reset logic".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Acked-by: Andiry Xu <Andiry.Xu@amd.com>
Acked-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The xHCI 1.0 spec errata released on June 13, 2011, changes the ordering
that the xHCI registers are saved and restored in. It moves the
interrupt pending (IMAN) and interrupt control (IMOD) registers to be
saved and restored last. I believe that's because the host controller
may attempt to fetch the event ring table when interrupts are
re-enabled. Therefore we need to restore the event ring registers
before we re-enable interrupts.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8 "USB: xHCI: PCI power
management implementation"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
The xhci_save_registers() function saved the event ring dequeue pointer
in the s3 register structure, but xhci_restore_registers() never
restored it. No other code in the xHCI successful resume path would
ever restore it either. Fix that.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8 "USB: xHCI: PCI power
management implementation".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
When xhci_mem_cleanup() is called, we can't be sure if the xHC is
actually halted. We can ask the xHC to halt by writing to the RUN bit
in the command register, but that might timeout due to a HW hang.
If the host controller is still running, we should not write zeroed
values to the event ring dequeue pointers or base tables, the DCBAA
pointers, or the command ring pointers. Eric Fu reports his VIA VL800
host accesses the event ring pointers after a failed register restore on
resume from suspend. The hypothesis is that the host never actually
halted before the register write to change the event ring pointer to
zero.
Remove all writes of zeroed values to pointer registers in
xhci_mem_cleanup(). Instead, make all callers of the function reset the
host controller first, which will reset those registers to zero.
xhci_mem_init() is the only caller that doesn't first halt and reset the
host controller before calling xhci_mem_cleanup().
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: stable@vger.kernel.org
Eric Fu reports a problem with his VIA host controller fetching a zeroed
event ring pointer on resume from suspend. The host should have been
halted, but we can't be sure because that code ignores the return value
from xhci_halt(). Print a warning when the host controller refuses to
halt within XHCI_MAX_HALT_USEC (currently 16 seconds).
(Update: it turns out that the VIA host controller is reporting a halted
state when it fetches the zeroed event ring pointer. However, we still
need this warning for other host controllers.)
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
While we're at that, define IMAN bitfield to aid readability.
The interrupt enable bit should be set once on driver init, and we
shouldn't need to continually re-enable it. Commit c21599a3 introduced
a read of the irq_pending register, and that allows us to preserve the
state of the IE bit. Before that commit, we were blindly writing 0x3 to
the register.
This patch should be backported to kernels as old as 2.6.36, or ones
that contain the commit c21599a361 "USB:
xhci: Reduce reads and writes of interrupter registers".
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch is used to fix a memory leak issue in s390/char/vmur.c.
A character device instance is allocated by cdev_alloc, the cdev_del
will not free that space if cdev_init is applied before.
Signed-off-by: Dennis Chen <dennis1.chen@amd.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Extend some error paths to call dasd_sfree_request as done earlier in the
function. The error-handling code is also moved to the end of the function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
According to an internal workaround master list, we need to set bit 5
of register 9400 to avoid issues with color blits.
Testing shows that this seems to fix the blitter hangs when fbc is
enabled on snb, thanks to Chris Wilson for figuring this out.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Michael "brot" Groh <michael.groh@minad.de>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The 845g shares the errata with i830 whereby executing a command
within 2 cachelines of the end of the ringbuffer may cause a GPU hang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most code assumes that the pinctrl ops are present. Validate this when
registering a pinctrl driver. Remove the one place in the code that
was checking whether one of these non-optional ops was present.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When no platform_data is present and either 'spi-num-chipselects' is
not defined in the DT or 'cs-gpios' has less entries than
'spi-num-chipselects' specifies, the NULL platform_data pointer is
being dereferenced.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes the following warning when "SAMSUNG EXYNOS5" is not selected:
warning: ‘exynos5_gpios_1’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_2’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_3’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_4’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F3IR
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
* tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
netdma: adding alignment check for NETDMA ops
ioatdma: DMA copy alignment needed to address IOAT DMA silicon errata
ioat: ring size variables need to be 32bit to avoid overflow
iop-adma: Corrected array overflow in RAID6 Xscale(R) test.
ioat: fix size of 'completion' for Xen
xhci_unregister_pci() is called in xhci_hcd_init().
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
of_gpio_simple_xlate() has an off-by-one bug where it checks to see if
args[0] is > ngpio instead of >=. args[0] must always be less than
ngpio because it is a zero-based enumeration.
Signed-off-by: Roland Stigge <stigge@antcom.de>
[grant.likely: beef up commit text]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The variable 'bit' is uninitialized in the first iteration of for
loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The irqdomain api changed significantly in v3.4 which caused a build
failure for this driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Hans J. Koch <hjk@linutronix.de>
Cc: Torben Hohn <torbenh@linutronix.de>
This reverts commit c1afdaff90.
Users have reported connection failures in 3.3.1 and suspend/resume
failures in 3.4-rcX. Revert this commit for now - PS IDLE can be
fixed in a clean manner later on.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move rt2x00rfkill_register(rt2x00dev) to rt2x00lib_probe_dev
function. It fixes of starting rfkill_poll function at the
right time if sets hard rfkill block and reboot. rt2x00mac_rfkill_poll
should be starting before bringing up the wireless interface.
Signed-off-by: Chen, Chien-Chia <machen@suse.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
CC: Kevin Chou <kevin.chou@mediatek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following is seen during allmodconfig builds for MIPS:
drivers/bcma/driver_pci_host.c:518:2: error: implicit declaration
of function 'pcibios_enable_device' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/bcma/driver_pci_host.o] Error 1
Most likey introduced by commit 49dc957715
"bcma: add PCIe host controller"
Add the header instead of implicitly assuming it will be present.
Sounds like a good idea, but that alone doesn't fix anything.
The real problem is that the Kconfig has settings related to whether
PCI is possible, i.e.
config BCMA_HOST_PCI_POSSIBLE
bool
depends on BCMA && PCI = y
default y
config BCMA_HOST_PCI
bool "Support for BCMA on PCI-host bus"
depends on BCMA_HOST_PCI_POSSIBLE
...but what is missing is that BCMA_DRIVER_PCI_HOSTMODE doesn't
have any dependencies on the above. Add one.
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a trivial rename to stop the build system complaining that we're
referencing things we shouldn't be.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=45TQ
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull a regulator build fix from Mark Brown:
"Fix a build warning in the anatop driver for 3.4
This is a trivial rename to stop the build system complaining that
we're referencing things we shouldn't be."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: anatop: fix 'anatop_regulator' name collision
We've only computed whether we need to fall back to 6bpc due to dp
link bandwidth constrains in mode_valid, but not mode_fixup. Under
various circumstances X likes to create new modes which then lack
proper 6bpc flags (if required), resulting in mode_fixup failures and
ultimately black screens.
Chris Wilson pointed out that we still get things wrong for bpp > 24,
but that should be fixed in another patch (and it'll be easier because
this patch consolidates the logic).
The likely culprit for this regression is
commit 3d794f87238f74d80e78a7611c7fbde8a54c85c2
Author: Keith Packard <keithp@keithp.com>
Date: Wed Jan 25 08:16:25 2012 -0800
drm/i915: Force explicit bpp selection for intel_dp_link_required
v2: Fix indentation and tune down the too bold claim that this should
fix the world. Both noticed by Chris Wilson.
v3: Try to really git add things.
Reported-and-tested-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48170
Cc: stable@kernel.org
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Image on Z11m cards was totally garbled due to wrong memory being
selected. Add a special handling for Z11m cards. Tested on PCIe Z11 and
Z11m cards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If gpio_request fails, we need to free all allocated resources.
Current code uses wrong array index to access gpio_data array.
So current code actually frees gpio_data[i].gpio by j times.
This patch moves the error handling code to err_out and thus improves
readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
m68k doesn't have memblock_reserve, which causes a build failure
with allmodconfig. Make PERSISTENT_RAM and RAM_CONSOLE depend on
HAVE_MEMBLOCK.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c client data set is of type struct indio_dev pointer and hence the
pointer returned from i2c_get_clientdata() should be assigned to
an object of type struct indio_dev and not to an object of type
struct ak8975_data.
Also in ak8975_probe() client data should be set first
before calling ak8975_setup() as it references the client data.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
CC: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not sure what triggered the change in behavior, but seems to
result in recursively acquiring a mutex and hanging on boot. But
omap_drm_init() seems a much more sane place to register the
driver for the DMM sub-device.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a memory leak in zsmalloc where the first
subpage of each zspage is leaked when the zspage is freed.
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Acked-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I already fixed the other similar for loop in this file. I'm not sure
how I missed this one. We use seg_no+1 inside the loop so we can't go
right up to the end of the loop.
Also if we don't break out of the loop then we end up past the end of
the array, but with this fix we end up on the last element.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added Rupesh Gujare to MAINTAINERS file and contact in TODO file
for ozwpan driver.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid "Bad LUN" and "Bad target number" message by setting the supported
max_lun and max_id for the scsi host
Signed-off-by: wwang <wei_wang@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtsx_transport.c (rtsx_transfer_sglist_adma_partial):
pointer struct scatterlist *sg, which is mapped in dma_map_sg,
is used as an iterator in later transfer operation. It is corrupted and
passed to dma_unmap_sg, thus causing fatal unmap of some erroneous address.
Fix it by duplicating *sg_ptr for iterating.
Signed-off-by: wwang <wei_wang@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to check the we don't copy too much memory. This comes from a
copy_from_user() in the ioctl.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If, in drivers/staging/media/as102/as102_fw.c::as102_fw_upload(), the call
cmd_buf = kzalloc(MAX_FW_PKT_SIZE, GFP_KERNEL);
should fail and return NULL so that we jump to the 'error:' label,
then we'll end up calling 'release_firmware(firmware);' with
'firmware' still uninitialized - not good.
The easy fix is to just initialize 'firmware' to NULL when we declare
it, since release_firmware() deals gracefully with being passed NULL
pointers.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The just-merged ramster staging driver was dependent on a cleanup patch in
cleancache, so was marked CONFIG_BROKEN until that patch could be
merged. That cleancache patch is now merged (and the correct SHA of the
cleancache patch is 3167760f83 rather than
the one shown in the comment removed in the patch below).
So remove the CONFIG_BROKEN now and the comment that is no longer true...
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of our errors wasn't negative as intended. Fix this.
(Found by Hillf Danton)
While we are at it turn user causable messages down to dev_dbg level in the
ioctl paths.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: eliminate NULL pointer dereference (bugfix)
This patch fixes a bug which causes NULL pointer dereference in
ffs_ep0_ioctl. The bug happens when the FunctionFS is not bound (either
has not been bound yet or has been bound and then unbound) and can be
reproduced with running the following commands:
$ insmod g_ffs.ko
$ mount -t functionfs func /dev/usbgadget
$ ./null
where null.c is:
#include <fcntl.h>
#include <linux/usb/functionfs.h>
int main(void)
{
int fd = open("/dev/usbgadget/ep0", O_RDWR);
ioctl(fd, FUNCTIONFS_CLEAR_HALT);
return 0;
}
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the non-required spinlock acquire/release calls on
'queue->irqlock' from 'uvc_queue_next_buffer' routine.
This routine is called from 'video->encode' function (which translates to
either 'uvc_video_encode_bulk' or 'uvc_video_encode_isoc') in 'uvc_video.c'.
As, the 'video->encode' routines are called with 'queue->irqlock' already held,
so acquiring a 'queue->irqlock' again in 'uvc_queue_next_buffer' routine causes
a spin lock recursion.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is crucial to assign each req->context value to struct rndis.
The problem happens for multi function gadget (g_multi) when multiple
functions are calling common usb_composite_dev control request.
It might happen that *_setup method from one usb function will
alter some fields of this common request issued by other USB
function.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
pm_runtime_get_sync returns a signed integer. In case of errors
it returns a negative value. This patch fixes the error check
by making it signed instead of unsigned thus preventing register
access if get_sync_fails. Also passes the error cause to the
debug message.
Cc: stable@vger.kernel.org
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During modprobe of gadget driver, pullup is called after
udc_start. In order to make the exit path symmetric when
removing a gadget driver, call pullup before ->udc_stop.
This is needed to avoid issues with PM where udc_stop
disables the module completely (put IP in reset state,
cut functional and interface clocks, and so on), which
prevents us from accessing the IP's address space,
thus creating the possibility of an abort exception
when we try to access IP's address space after clocks
are off.
Cc: stable@vger.kernel.org
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
pm_runtime_enable is being called after omap2430_musb_init. Hence
pm_runtime_get_sync in omap2430_musb_init does not have any effect (does
not enable clocks) resulting in a crash during register access. It is
fixed here.
Cc: stable@vger.kernel.org # v3.0, v3.1, v3.2, v3.3
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb can be suspended at the time some other driver wants to do ulpi
transfers using usb_phy_io_* functions, and that can cause data abort,
as it happened with isp1704_charger:
http://article.gmane.org/gmane.linux.kernel/1226122
Add pm_runtime to ulpi functions to rectify this. This also adds io_dev
to usb_phy so that pm_runtime_* functions can be used.
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Control transfers with data expected from device to host will use usb_rcvctrlpipe()
for urb->pipe so for such urbs 'is_in' will be set causing control urb to fall
into the first "if" condition in musb_cleanup_urb().
Fixed by adding logic to check for non control endpoints.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
make module init & exit __init & __exit
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
clear FFS_FL_BOUND flag on unbind (bugfix)
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Array should be freed together with event buffers, since it was
allocated dynamically.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DMA address register shouldn't be updated manually if transfer size
requires multiple packets.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Writing to TxFIFO relates only to Slave mode and leads to
TxFIFO corruption in DMA mode.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to documentation, TX FIFO_number index starts from 1.
For IN endpoint FIFO 0 we use GNPTXFSIZ register for programming
the size and memory start address.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- For Control Read transfer, the ACK handshake on an IN transaction
may be corrupted, so the device may not receive the ACK for data
stage, the complete irq will not occur at this situation.
Therefore, we need to move prime status stage from complete irq
routine to the place where the data stage has just primed, or the
host will never get ACK for status stage.
The above issue has been described at USB2.0 spec chapter 8.5.3.3.
- After adding prime status stage just after prime the data stage,
there is a potential problem when the status dTD is added before the data stage
has primed by hardware. The reason is the device's dTD descriptor has NO direction bit,
if data stage (IN) prime hasn't finished, the status stage(OUT)
dTD will be added at data stage dTD's Next dTD Pointer, so when the data stage
transfer has finished, the status dTD will be primed as IN by hardware,
then the host will never receive ACK from the device side for status stage.
- Delete below code at fsl_ep_queue:
/* Update ep0 state */
if ((ep_index(ep) == 0))
udc->ep0_state = DATA_STATE_XMIT;
the udc->ep0_state will be updated again after udc->driver->setup
finishes.
It is tested at i.mx51 bbg board with g_mass_storage, g_ether, g_serial.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When runtime_pm was originally added, it was done in rather confusing
way: omap2430_musb_init() (called from musb_init_controller) would do
runtime_pm_get_sync() and musb_init_controller() itself would do
runtime_pm_put to balance it out. This is not only confusing but also
wrong if non-omap2430 glue layer is used.
This confusion resulted in commit 772aed45b6 "usb: musb: fix
pm_runtime mismatch", that removed runtime_pm_put() from
musb_init_controller as that looked unbalanced, and also happened to
fix unrelated isp1704_charger crash. However this broke runtime PM
functionality (musb is now always powered, even without gadget active).
Avoid these confusing runtime pm dependences by making
musb_init_controller() and omap2430_musb_init() do their own runtime
get/put pairs; also cover error paths. Remove unneeded runtime_pm_put
in omap2430_remove too. isp1704_charger crash that motivated
772aed45b6 will be fixed by following patch.
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This change prevents runtime suspend and resume actual execution, if
omap2430 controller driver is loaded after musb-hdrc, and therefore the
controller isn't initialized properly.
The problem is reproducible with 3.1.y and 3.2 kernels.
Kernel configuration of musb:
% cat .config | egrep 'MUSB|GADGET'
CONFIG_USB_MUSB_HDRC=y
# CONFIG_USB_MUSB_TUSB6010 is not set
CONFIG_USB_MUSB_OMAP2PLUS=m
# CONFIG_USB_MUSB_AM35X is not set
CONFIG_MUSB_PIO_ONLY=y
CONFIG_USB_GADGET=y
# CONFIG_USB_GADGET_DEBUG is not set
# CONFIG_USB_GADGET_DEBUG_FILES is not set
# CONFIG_USB_GADGET_DEBUG_FS is not set
CONFIG_USB_GADGET_VBUS_DRAW=2
CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS=2
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_GADGET_DUALSPEED=y
CONFIG_USB_GADGETFS=m
# CONFIG_USB_MIDI_GADGET is not set
Fixes the following oops on module unloading:
Unable to handle kernel NULL pointer dereference at virtual address 00000220
----8<----
[<bf162088>] (omap2430_runtime_resume+0x24/0x54 [omap2430]) from [<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50)
[<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50) from [<c0031a24>] (_od_runtime_resume+0x28/0x2c)
[<c0031a24>] (_od_runtime_resume+0x28/0x2c) from [<c0306cb0>] (__rpm_callback+0x60/0xa0)
[<c0306cb0>] (__rpm_callback+0x60/0xa0) from [<c0307f2c>] (rpm_resume+0x3fc/0x6e4)
[<c0307f2c>] (rpm_resume+0x3fc/0x6e4) from [<c030851c>] (__pm_runtime_resume+0x5c/0x90)
[<c030851c>] (__pm_runtime_resume+0x5c/0x90) from [<c02fd0dc>] (__device_release_driver+0x2c/0xd0)
[<c02fd0dc>] (__device_release_driver+0x2c/0xd0) from [<c02fda18>] (driver_detach+0xe8/0xf4)
[<c02fda18>] (driver_detach+0xe8/0xf4) from [<c02fcf88>] (bus_remove_driver+0xa0/0x104)
[<c02fcf88>] (bus_remove_driver+0xa0/0x104) from [<c02fde54>] (driver_unregister+0x60/0x80)
[<c02fde54>] (driver_unregister+0x60/0x80) from [<c02ff2d4>] (platform_driver_unregister+0x1c/0x20)
[<c02ff2d4>] (platform_driver_unregister+0x1c/0x20) from [<bf162928>] (omap2430_exit+0x14/0x1c [omap2430])
[<bf162928>] (omap2430_exit+0x14/0x1c [omap2430]) from [<c007d8bc>] (sys_delete_module+0x1f4/0x264)
[<c007d8bc>] (sys_delete_module+0x1f4/0x264) from [<c000f000>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # 3.1
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this default case returning an error,
thus replying with a stall, we would fail
USB30CV TD 9.11 Bad Feature test case.
Cc: stable@vger.kernel.org
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Direct usage of the asm include has long been deprecated by the
introduction of gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Don't call i2c_enable on resume because it causes a spurious
interrupt.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some r4xx chips have the wrong frev in the
DVOEncoderControl table. It should always be 1
on r4xx. Fixes modesetting on DVO on r4xx chips
with the bad frev.
Reported by twied on #radeon.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since cmdbuf->size and cmdbuf->nbox are from userspace, a large value
would overflow the allocation size, leading to out-of-bounds access.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
due to a HW limitation we have a bounce buffer for ep0
out transfers which are not aligned with MaxPacketSize.
On such case we were not increment r->actual as we should.
This patch fixes that mistake.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
To allow ep0 out transfers of upto bounce buffer size
instead of maxpacketsize, use the transfer size as multiple
of ep0 maxpacket size.
Cc: stable@vger.kernel.org
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we want to do device-initiated disconnect,
let's make sure we stop the UDC in order to
e.g. allow lower power states to be achieved by
turning off unnecessary clocks and/or stoping
PHYs.
When reconnecting, call ->udc_start() again to
make sure UDC is reinitialized.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some architectures require that delays longer than a few
miliseconds are called through mdelay. This was triggered
on ARM randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add pointer and buttonpad properties for v4 hardware.
Also, Jachiet reported that on Asus UX31, right button has no effect.
It turns out v4 has only one button, the right-button effect is
implemented with software when Windows driver is installed, or in
firmware when touchpad is in relative mode. So remove BTN_RIGHT
while at it.
Reported-by: Jachiet Louis <louis@jachiet.com>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acer VH40 has a Fn key toggling the touchpad on and off, but it's
implemented in system firmware, and the EC chip has to receive
reset command to activate this function. Also when this machine
wakes up after resume, psmouse_reset is necessary to bring the
touchpad back on.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The task handoff notifier leaks task_struct since it never gets freed
after the callback returns NOTIFY_OK, which means it is responsible for
doing so.
It turns out the lowmemorykiller actually doesn't need this notifier at
all. It's used to prevent unnecessary killing by waiting for a thread
to exit as a result of lowmem_shrink(), however, it's possible to do
this in the same way the kernel oom killer works by setting TIF_MEMDIE
and avoid killing if we're still waiting for it to exit.
The kernel oom killer will already automatically set TIF_MEMDIE for
threads that are attempting to allocate memory that have a fatal signal.
The thread selected by lowmem_shrink() will have such a signal after the
lowmemorykiller sends it a SIGKILL, so this won't result in an
unnecessary use of memory reserves for the thread to exit.
This has the added benefit that we don't have to rely on
CONFIG_PROFILING to prevent needlessly killing tasks.
Reported-by: Werner Landgraf <w.landgraf@ru.ru>
Cc: stable@vger.kernel.org
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1538) causes uhci_hub_status_data() to return a nonzero
value when any port is undergoing a resume transition while the root
hub is suspended. This will allow usbcore to handle races between
root-hub suspend and port wakeup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1537) adds a bit-array to ehci-hcd for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when ehci_hub_status_data() is called, the routine will return
a nonzero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1533) fixes a race between root-hub suspend and remote
wakeup. If a wakeup event occurs while a root hub is suspending, it
might not cause the suspend to fail. Although the host controller
drivers check for pending wakeup events at the start of their
bus_suspend routines, they generally do not check for wakeup events
while the routines are running.
In addition, if a wakeup event occurs any time after khubd is frozen
and before the root hub is fully suspended, it might not cause a
system sleep transition to fail. For example, the host controller
drivers do not fail root-hub suspends when a connect-change event is
pending.
To fix both these issues, this patch causes hcd_bus_suspend() to query
the controller driver's hub_status_data method after a root hub is
suspended, if the root hub is enabled for wakeup. Any pending status
changes will count as wakeup events, causing the root hub to be
resumed and the overall suspend to fail with -EBUSY.
A significant point is that not all events are reflected immediately
in the status bits. Both EHCI and UHCI controllers notify the CPU
when remote wakeup begins on a port, but the port's suspend-change
status bit doesn't get set until after the port has completed the
transition out of the suspend state, some 25 milliseconds later.
Consequently, the patch will interpret any nonzero return value from
hub_status_data as indicating a pending event, even if none of the
status bits are set in the data buffer. Follow-up patches make the
necessary changes to ehci-hcd and uhci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just add new device id. 3G works fine, LTE not tested.
Signed-off-by: Anton Samokhvalov <pg83@yandex.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two issues here, one is that the device is generating
spurious very fast modem status line changes somewhere:
CTS becomes high then low 18µs later:
[121226.924373] ftdi_process_packet: prev rng=0 dsr=10 dcd=0 cts=6
[121226.924378] ftdi_process_packet: status=10 prev=00 diff=10
[121226.924382] ftdi_process_packet: now rng=0 dsr=10 dcd=0 cts=7
(wake_up_interruptible is called)
[121226.924391] ftdi_process_packet: prev rng=0 dsr=10 dcd=0 cts=7
[121226.924394] ftdi_process_packet: status=00 prev=10 diff=10
[121226.924397] ftdi_process_packet: now rng=0 dsr=10 dcd=0 cts=8
(wake_up_interruptible is called)
This wakes up the task in TIOCMIWAIT:
[121226.924405] ftdi_ioctl: 19451 rng=0->0 dsr=10->10 dcd=0->0 cts=6->8
(wait from 20:51:46 returns and observes both changes)
Which then calls TIOCMIWAIT again:
20:51:46.400239 ioctl(3, TIOCMIWAIT, 0x20) = 0
22:11:09.441818 ioctl(3, TIOCMGET, [TIOCM_DTR|TIOCM_RTS]) = 0
22:11:09.442812 ioctl(3, TIOCMIWAIT, 0x20) = -1 EIO (Input/output error)
(the second wake_up_interruptible takes effect and an I/O error occurs)
The other issue is that TIOCMIWAIT will wait forever (unless the task is
interrupted) if the device is removed.
This change removes the -EIO return that occurs if the counts don't
appear to have changed. Multiple counts may have been processed as
one or the waiting task may have started waiting after recording the
current count.
It adds a bool to indicate that the device has been removed so that
TIOCMIWAIT doesn't wait forever, and wakes up any tasks so that they can
return -EIO.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling of TIOCMIWAIT was changed by commit 1d749f9afa
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
FTDI_STATUS_B0_MASK does not indicate the changed modem status lines,
it indicates the value of the current modem status lines. An xor is
still required to determine which lines have changed.
The count was only being incremented if the line was high. The only
reason TIOCMIWAIT still worked was because the status packet is
repeated every 1ms, so the count was always changing. The wakeup
itself still ran based on the status lines changing.
This change fixes handling of updates to the modem status lines and
allows multiple processes to use TIOCMIWAIT concurrently.
Tested with two processes waiting on different status lines being
toggled independently.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1532) fixes a mistake in the USB suspend code. When the
system is going to sleep, we should ignore errors in powering down USB
devices, because they don't really matter. The devices will go to low
power anyway when the entire USB bus gets suspended (except for
SuperSpeed devices; maybe they will need special treatment later).
However we should not ignore errors in suspending root hubs,
especially if the error indicates that the suspend raced with a wakeup
request. Doing so might leave the bus powered on while the system was
supposed to be asleep, or it might cause the suspend of the root hub's
parent controller device to fail, or it might cause a wakeup request
to be ignored.
The patch fixes the problem by ignoring errors only when the device in
question is not a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chen Peter <B29397@freescale.com>
CC: <stable@vger.kernel.org>
Tested-by: Chen Peter <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1536) fixes a bug in the USB serial core. Unloading and
reloading a serial driver while a serial device is plugged in causes
errors because of the code in usb_serial_disconnect() that tries to
make sure the port_remove method is called. With the new order of
driver registration introduced in the 3.4 kernel, this is definitely
not the right thing to do (if indeed it ever was).
The patch removes that whole section code, along with the mechanism
for keeping track of each port's registration state, which is no
longer needed. The driver core can handle all that stuff for us.
Note: This has been tested only with one or two USB serial drivers.
In theory, other drivers might still run into trouble. But if they
do, it will be the fault of the drivers, not of this patch -- that is,
the drivers will need to be fixed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The right idProduct for Metrologic Bar Code Scanner
in Uni-Directional Serial Emulation mode is 0x0700.
Also rename idProduct for Bi-Directional mode to be a bit more informative.
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DTR/RTS should only be raised when changing baudrate from B0 and not on
any baud rate change (> B0).
Reported-by: Søren Holm <sgh@sgh.dk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes:
note: expected ‘struct ida *’ but argument is of type ‘struct idr *’
warning: passing argument 1 of ‘ida_pre_get’ from incompatible pointer type
Reported-by: Arnd Bergman <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
soc_lock is already initialized by DEFINE_SPINLOCK.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the rate-control indexing is incorrectly set up, mac80211 issues
a warning and returns NULL from the call to ieee80211_get_tx_rate().
When this happens, avoid a NULL pointer dereference.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before the switch to asynchronous firmware loading (mainline commit b0302ab),
it was necessary to load firmware when initializing the first of the units
in a dual-mac system. After the change, it is necessary to load firmware in
both units.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the case where we are changing from one framebuffer to
another, we need to be sure that there are no pending WAIT_FOR_EVENTs on
the pipe for the current framebuffer before switching. If we disable the
pipe, and then try to execute a WAIT_FOR_EVENT it will block
indefinitely and cause a GPU hang.
We attempted to fix this in commit 85345517fe
(drm/i915: Retire any pending operations on the old scanout when switching)
for the case of mode switching, but this leaves the condition where we
are switching off the pipe vulnerable.
There still remains the race condition were a display may be unplugged,
switched off by the core, a uevent sent to notify the DDX and the DDX
may issue a WAIT_FOR_EVENT before it processes the uevent. This window
does not exist if the pipe is only switched off in response to the
uevent. Time to make sure that is so...
Reported-by: Francis Leblanc <Francis.Leblanc-Lebeau@verint.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36515
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45413
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fixup spelling in comment, noticed by Eugeni.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The destination color key is always enabled for IVB. Removed
the line that does this.
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some configurations produce the following compiler warning:
drivers/hwmon/pmbus/pmbus_core.c: In function 'pmbus_show_boolean':
drivers/hwmon/pmbus/pmbus_core.c:752: warning: 'val' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from pmbus_get_boolean with both val and error return code (val is a
boolean and thus never negative).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some configurations produce the following compiler warning:
drivers/hwmon/smsc47m1.c: In function 'sm_smsc47m1_init':
drivers/hwmon/smsc47m1.c:938: warning: 'address' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from smsc47m1_find with both address and error return code (the address
is an unsigned short and thus never negative). This also reduces module size by
a few bytes (46 bytes for x86_64).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
In some configurations, BUG() does not result in an endless loop but returns
to the caller. This results in the following compiler warning:
drivers/hwmon/acpi_power_meter.c: In function 'show_str':
drivers/hwmon/acpi_power_meter.c:380: warning: 'val' may be used uninitialized in this function
Fix the warning by setting val to an empty string after BUG().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some configurations produce the following compiler warning:
drivers/hwmon/smsc47b397.c: In function 'smsc47b397_init':
drivers/hwmon/smsc47b397.c:385: warning: 'address' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from smsc47b397_find with both address and error return code (the address
is an unsigned short and thus never negative). This also reduces module size by
a few bytes (64 bytes for x86_64).
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add UART clock quirk for the Kontron COMe-mTT10 module.
The board has previously been called nanoETXexpress-TT, therefore this
is also checked.
As suggested by Darren Hart the comparison in this patch version is
placed after the FRI2 checks to ensure it will also work with possible
upcoming changes to the FRI2 firmware.
This patch follows the patchset submitted by Darren Hart at
commit a46f5533ec.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch (MSI setting) is not enough.
commit e463595fd9
Author: Alexander Stein <alexander.stein@systec-electronic.com>
Date: Mon Jul 4 08:58:31 2011 +0200
pch_uart: Add MSI support
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To enable MSI mode, PCI bus-mastering must be enabled.
This patch enables the setting.
cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Workaround dropped notifications in the iir register. Register reads
coincident with new interrupt notifications sometimes result in this
device clearing the interrupt event without reporting it in the read
data.
The serial core already has a heuristic for determining when a device
has an untrustworthy iir register. In this case when we apriori know
that the iir is faulty use a flag (UPF_BUG_THRE) to bypass the test and
force usage of the background timer.
[stable: 3.3.x]
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Reported-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Tested-by: Nhan H Mai <nhan.h.mai@intel.com>
Tested-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 448ac154c9.
The semantic of UPF_IIR_ONCE is only guaranteed to workaround the race
condition in the kt serial's iir register if the only source of
interrupts is THRE (fifo-empty) events. An modem status event at the
wrong time can again cause an iir read to drop the 'empty' status
leading to a hang. So, revert this in preparation for using the
existing "I don't trust my iir register" workaround in the 8250 core
(UART_BUG_THRE).
[stable: 3.3.x]
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e86ff4a63c.
This tried to enforce the semantics of one interrupt per iir read of the
THRE (transmit-hold empty) status, but events from other sources
(particularly modem status) defeat this guarantee.
This change also broke 8250_pci suspend/resume support as
pciserial_resume_ports() re-runs .init() quirks, but does not run
.exit() quirks in pciserial_suspend_ports() leading to reports like:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:16.3/msi_irqs'
...and a subsequent crash. The mismatch of init/exit at suspend/resume
seems like a bug in its own right.
[stable: 3.3.x]
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the omap serial driver is built as a module, we must
not allow the console driver to be selected, because consoles
can not be loadable modules.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix omission initialize ulcon in s3c24xx_serial_resetport(),
reset port function in drivers/tty/serial/samsung.c. It has
been happened from commit 0dfb3b41("serial: samsung: merge
all SoC specific port reset functions")
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@vger.kernel.org> [3.3]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A prototype for kmsg records instead of a byte-stream buffer revealed
a couple of missing printk(KERN_CONT ...) uses. Subsequent calls produce
one record per printk() call, while all should have ended up in a single
record.
Instead of:
ACPI: (supports S0 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
hpet0: at MMIO 0xfed00000, IRQs 2 , 8 , 0
It prints:
ACPI: (supports S0
S5
)
ACPI: PCI Interrupt Link [LNKA] (IRQs
5
*10
11
)
hpet0: at MMIO 0xfed00000, IRQs
2
, 8
, 0
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On our custom board, we are using RS485 in half-duplex mode on an AT91SAM9G45.
SER_RS485_RX_DURING_TX is not set as we do not want to receive the data we
transmit (our transceiver will receive transmitted data).
Although the current driver attempts to disable and enable the receiver at the
appropriate points, incoming data is still loaded into the receive register
causing our code to receive the very last byte that was sent once the receiver
is enabled.
I ran this by Atmel support and they wrote: "The issue comes from the fact
that you disable the PDC/DMA Reception and not the USART Reception channel. In
your case, the[n] you will still receive data into the USART_RHR register, and
maybe you [h]ave the overrun flag set. So please disable the USART reception
channel."
The following patch should force the driver to enable/disable the receiver via
RXEN/RXDIS fields of the USART control register. It fixed the issue I was
having.
Signed-off-by: Gabe Siftar <gabe.siftar@getingeusa.com>
[nicolas.ferre@atmel.com: slightly modify commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow altera_jtag_uart. This fixes a crash if there is a mistake in the DTS.
Signed-off-by: Yuriy Kozlov <ykozlov@ptcusa.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "TTY buffer in tty_port" patchset introduced an opencoded
debug message in the Gigaset tty device if_close() function.
Change it to use the gig_dbg() macro like everywhere else in
the driver.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch does the following
- The pm_runtime_disable is called in the remove not in the error
case of probe.The patch calls the pm_runtime_disable in the error
case.
- Calls pm_runtime_put in the error case.
- The up is not freed in the error path. Fix the memory leak by using
devm_* so that the memory need not be freed in the driver.
- Also the iounmap is not called fix the same by calling using devm_ioremap.
- Make the name of the error tags more meaningful.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver frees the clock samples buffer before stopping the video
buffers queue. If a DQBUF call arrives in-between,
uvc_video_clock_update() will be called with a NULL clock samples
buffer, leading to a crash. This occurs very frequently when using the
webcam with the flash browser plugin.
Move clock initialization/cleanup to uvc_video_enable() in order to free
the clock samples buffer after the queue is stopped. Make sure the clock
is reset at resume time to avoid miscalculating timestamps.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
has_get_frontend() should return a boolean, not a pointer.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some systems the device does not respond or give obscure values after cold,
warm or firmware reboot.
This patch retries to get chip version and type 5 times. If it
fails it applies chip version 0x1 and type 0x9135.
This patch does not fix warm cycle problems from other operating
systems and indeed the reverse applies. Users should power off cold boot.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When I converted ivtv to the new decoder API I introduced a regression in the
support of the old channel select API.
Thanks to Martin Dauskardt for reporting this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The commit e399ce77e6 has broken the DVB ABI for xine:
The problem is that xine is expecting every event after a successful
FE_SET_FRONTEND ioctl to have a non-zero frequency parameter, regardless
of whether the tuning process has LOCKed yet. What used to happen is
that the events inherited the initial tuning parameters from the
FE_SET_FRONTEND call. However, the fepriv->parameters_out struct is now
not initialised until the status contains the FE_HAS_LOCK bit.
You might argue that this behaviour is intentional, except that if an
application other than xine uses the DVB adapter and manages to set the
parameters_out.frequency field to something other than zero, then xine
no longer has any problems until either the adapter is replugged or the
kernel modules reloaded. This can only mean that the
fepriv->parameters_out struct still contains the (stale) tuning
information from the previous application.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Cc: stable@kernel.org # for kernel version 3.3
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Access to global talitos registers must be protected for the case when
affinities are configured such that primary and secondary talitos irqs
run on different cpus.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Dump tagmap on failure, instead of individual tags.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* If a ncq command time out and a non-ncq command is active, skip restart port
* Queue(pause) ncq commands during operations spanning more than one non-ncq commands - secure erase, download microcode
* When a non-ncq command is active, allow incoming non-ncq commands to wait instead of failing back
* Changed timeout for download microcode and smart commands
* If the device in write protect mode, fail all writes (do not send to device)
* Set maximum retries to 2
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Shortened macros used to represent mtip_port->flags and dd->dd_flag
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Handle the interrupt completion of polled internal commands
* Do not check remove pending flag for standby command
* On rebuild failure,
- set corresponding bit dd_flag
- do not send standby command
* Free ida index in remove path
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Add support for detecting the following device status
- write protect
- over temp (thermal shutdown)
* Add new sysfs entry 'status', possible values - online, write_protect, thermal_shutdown
* Add new file 'sysfs-block-rssd' to document ABI (Reported-by: Greg Kroah-Hartman)
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Moved setting completion time into mtip_issue_ncq_command()
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Merged the following flags into one variable 'dd_flag':
* drv_cleanup_done
* resumeflag
* Added the following flags into 'dd_flag'
* remove pending
* init done
* Removed 'ftlrebuildflag' (similar flag is already part of mti_port->flags)
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is needed to catch the resume bug that was bothering lots of us from
testing some XHCI bug fixes in the suspend/resume path.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kyrofb is completely broken on x86_64 because the registers are defined as
unsigned long. Change them to u32 to make the driver work.
Tested with Hercules 3D Prophet 4000XT.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Two more small fixes:
- Now we have users for it that aren't running Android it turns out that
regcache_sync_region() is much more useful to drivers if it's exported
for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of rbtrees,
not visible up until now because everything was providing at least
some cache on startup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qm1Q
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull two more small regmap fixes from Mark Brown:
- Now we have users for it that aren't running Android it turns out
that regcache_sync_region() is much more useful to drivers if it's
exported for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of
rbtrees, not visible up until now because everything was providing at
least some cache on startup.
* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: prevent division by zero in rbtree_show
regmap: Export regcache_sync_region()
Ren Mingxin