Omap DMA controller can prefetch data in advance in case of
destination synchronized data transfer. This may increase
performance when target HW block doesn't have fifo.
Data is waiting for transfer request in DMA fifo instead of read from memory.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap24xx_check_revision, omap3_check_features,
omap3_check_revision, omap4_check_revision, omap3_cpuinfo
are not used elsewhere, it should be static
Also fixes the following sparse warnings:
arch/arm/mach-omap2/id.c:105:13: warning: symbol 'omap24xx_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:167:13: warning: symbol 'omap3_check_features'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:189:13: warning: symbol 'omap3_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:270:13: warning: symbol 'omap4_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:300:13: warning: symbol 'omap3_cpuinfo'
was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The original patch got truncated when applied from patchwork.kernel.org
as discussed at:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg28953.html
This patch supplies the missing chunks.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
[tony@atomide.com: added more info to the patch description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix GPIO numbers and smc91x for 2430sdp. The earlier code
had cut and paste errors from 3430sdp code. Also, 2430
has five GPIO banks for a total of 160 GPIO lines.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds in the necessary clocks and mux pins for UART
control on omap7xx devices. I also made a change in the serial
code to only try and initialize two UARTs in omap_serial_init, as
these devices don't have three.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Recent DEBUG_LL and uncompress.h changes removed the check_port()
as pointed out by Cory Maccarrone <darkstar6262@gmail.com>.
This causes some boards to not boot, so add back the MDR1 register
check. The MDR1 register tells the mode of omap uart. Based on
an earlier patch by Cory Maccarrone <darkstar6262@gmail.com>.
Tested-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
cyber2000fb: fix console in truecolor modes
cyber2000fb: fix machine hang on module load
SA1111: Eliminate use after free
ARM: Fix Versatile/Realview/VExpress MMC card detection sense
ARM: 6279/1: highmem: fix SMP preemption bug in kmap_high_l1_vipt
ARM: Add barriers to io{read,write}{8,16,32} accessors as well
ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE
ARM: 6272/1: Convert L2x0 to use the IO relaxed operations
ARM: 6271/1: Introduce *_relaxed() I/O accessors
ARM: 6275/1: ux500: don't use writeb() in uncompress.h
ARM: 6270/1: clean files in arch/arm/boot/compressed/
ARM: Fix csum_partial_copy_from_user()
__sa1111_remove always frees its argument, so the subsequent reference to
sachip->saved_state represents a use after free. __sa1111_remove does not
appear to use the saved_state field, so the patch simply frees it first.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E2;
@@
__sa1111_remove(E)
...
(
E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMC card detection sense has become really confused with negations
at various levels, leading to some platforms not detecting inserted
cards. Fix this by converting everything to positive logic throughout,
thereby getting rid of these negations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
smp_processor_id() must not be called from a preemptible context (this
is checked by CONFIG_DEBUG_PREEMPT). kmap_high_l1_vipt() was doing so.
This lead to a problem where the wrong per_cpu kmap_high_l1_vipt_depth
could be incremented, causing a BUG_ON(*depth <= 0); in
kunmap_high_l1_vipt().
The solution is to move the call to smp_processor_id() after the call
to preempt_disable().
Originally by: Andrew Howe <ahowe@nvidia.com>
Signed-off-by: Gary King <gking@nvidia.com>
Acked-by: Nicolas Pitre <nico.as.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ioread/iowrite accessors also need barriers as they're used in
place of readl/writel et.al. in portable drivers. Create __iormb()
and __iowmb() which are conditionally defined to be barriers dependent
on ARM_DMA_MEM_BUFFERABLE, and always use these macros in the accessors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the coherent DMA buffers are mapped as Normal Non-cacheable
(ARM_DMA_MEM_BUFFERABLE enabled), buffer accesses are no longer ordered
with Device memory accesses causing failures in device drivers that do
not use the mandatory memory barriers before starting a DMA transfer.
LKML discussions led to the conclusion that such barriers have to be
added to the I/O accessors:
http://thread.gmane.org/gmane.linux.kernel/683509/focus=686153http://thread.gmane.org/gmane.linux.ide/46414http://thread.gmane.org/gmane.linux.kernel.cross-arch/5250
This patch introduces a wmb() barrier to the write*() I/O accessors to
handle the situations where Normal Non-cacheable writes are still in the
processor (or L2 cache controller) write buffer before a DMA transfer
command is issued. For the read*() accessors, a rmb() is introduced
after the I/O to avoid speculative loads where the driver polls for a
DMA transfer ready bit.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is in preparation for a subsequent patch which adds barriers
to the I/O accessors. Since the mandatory barriers may do an L2 cache
sync, this patch avoids a recursive call into l2x0_cache_sync() via the
write*() accessors and wmb() and a call into l2x0_cache_sync() with the
l2x0_lock held.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces readl*_relaxed()/write*_relaxed() as the main I/O
accessors (when __mem_pci is defined). The standard read*()/write*()
macros are now based on the relaxed accessors.
This patch is in preparation for a subsequent patch which adds barriers
to the I/O accessors.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't use writeb() in uncompress.h, to avoid the following build errors
when the "Add barriers to the I/O accessors" series is applied. Use
__raw_writeb() instead.
arch/arm/boot/compressed/misc.o: In function `putc':
arch/arm/mach-ux500/include/mach/uncompress.h:41:
undefined reference to `outer_cache'
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the compressed boot Makefile for ARM to
remove files during clean.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
wm8350-regulator: fix wm8350_register_regulator error handling
ab3100: fix off-by-one value range checking for voltage selector
Per the da850/omap-l138 Beta EVM SOM schematic, the DEFDCDC2 and
DEFDCDC3 lines are tied high. This leads to a 3.3V IO and 1.2V CVDD
voltage.
Pass the right platform data to the TPS6507x driver so it can operate
on the DEFDCDC{2,3}_HIGH register to read and change voltage levels.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Commit 3fea60261e ("Input: twl40300-keypad - fix handling of "all
ground" rows") broke compilation as I managed to use non-existent
keycodes.
Reported-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using the parent functions frame pointer to access our arguments is
completely wrong, whether or not we're building with frame pointers
or not. What we should be using is the stack pointer to get at the
word above the registers we stacked ourselves.
Reported-by: Bosko Radivojevic <bosko.radivojevic@gmail.com>
Tested-by: Bosko Radivojevic <bosko.radivojevic@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
qnap_tsx1x_register_flash is only called by qnap_ts219_init and
qnap_ts41x_init which both live in .init.text, too. So the move is OK.
This fixes the following warning in kirkwood_defconfig:
WARNING: vmlinux.o(.text+0x9334): Section mismatch in reference from the function qnap_tsx1x_register_flash() to the variable .init.data:qnap_tsx1x_spi_slave_info
The function qnap_tsx1x_register_flash() references
the variable __initdata qnap_tsx1x_spi_slave_info.
This is often because qnap_tsx1x_register_flash lacks a __initdata
annotation or the annotation of qnap_tsx1x_spi_slave_info is wrong.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
the different putc variants used an initialized local static variable
which is broken since
5de813b (ARM: Eliminate decompressor -Dstatic= PIC hack)
This needs to be initialized at runtime and so needs to be global.
While at it give it a better name.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need mach/hardware.h for CLPS7111_VIRT_BASE.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mov rx, =<immediate> isn't valid, use #<immediate> instead.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need asm/memory.h for NS9XXX_CSxSTAT_PHYS (via mach/memory.h).
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IO_BASE shoule be IO_VIRT, and IO_START should be IO_PHYS. We also need
mach/hardware.h for these definitions.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - relax capability ID checks on newer hardware
Input: twl40300-keypad - fix handling of "all ground" rows
Input: gamecon - reference correct pad in gc_psx_command()
Input: gamecon - reference correct input device in NES mode
Input: w90p910_keypad - change platfrom driver name to 'nuc900-kpi'
Input: i8042 - add Gigabyte Spring Peak to dmi_noloop_table
Input: qt2160 - rename kconfig symbol name
Delete a wrong redundant right parenthesis in
arch/arm/mach-footbridge/common.c
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to fix nuc900 touchscreen clk definition bug,the .dev_id's
name should be 'nuc900-ts', it should be the same to pdev.name. or else,
the touchscreen driver will be not working well due to clock engine disabled.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Nokia RX51 board code (arch/arm/mach-omap2/board-rx51-peripherals.c)
defines a key map for the matrix keypad keyboard. The hardware seems to
use all of the 8 rows and 8 columns of the keypad, although not all
possible locations are used.
The TWL4030 supports keypads with at most 8 rows and 8 columns. Most keys
are defined with a row and column number between 0 and 7, except
KEY(0xff, 2, KEY_F9),
KEY(0xff, 4, KEY_F10),
KEY(0xff, 5, KEY_F11),
which represent keycodes that should be emitted when entire row is
connected to the ground. since the driver handles this case as if we
had an extra column in the key matrix. Unfortunately we do not allocate
enough space and end up owerwriting some random memory.
Reported-and-tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
From: Bin Yang <bin.yang@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Bin Yang <bin.yang@marvell.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The wrong CONFIG defines were checked, and the <mach/audio.h>
include was missing
Signed-off-by: pieter <p.grimmerink@inepro.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch:
1) Simpifies the DRI recomputation routine by pulling out the common code
2) Fixes a bug in PXA27x DRI recomputation caused by incorrect parenthesis
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'arm/defconfig/reduced-v2.6.35-rc1' of git://git.pengutronix.de/git/ukl/linux-2.6:
ARM: reduce defconfigs
This is a big change, but results in no loss of information, despite us
losing almost 200k lines:
177 files changed, 652 insertions(+), 194157 deletions(-)
and Grant Likely thinks powerpc can also use the same reduction
technique.
The python script that did the reduction looks like this:
#! /usr/bin/env python
# vim: set fileencoding=utf-8 :
# Copyright (C) 2010 by Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
import re
import subprocess
import os
import sys
# This prevents including a timestamp in the .config which makes comparing a
# bit easier.
os.environ['KCONFIG_NOTIMESTAMP'] = 'Yes, please'
# XXX: get these using getopt
kernel_tree = '' # os.path.join(os.environ['HOME'], 'gsrc', 'linux-2.6')
arch = 'arm'
target = sys.argv[1]
defconfig_src = os.path.join(kernel_tree, 'arch/%s/configs/%s' % (arch, target))
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
origconfig = list(open('.config'))
config = list(origconfig)
config_size = os.stat('.config').st_size
i = 0
while i < len(config):
print 'test for %r' % config[i]
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config[:i])
defconfig.writelines(config[i + 1:])
defconfig.close()
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
if os.stat('.config').st_size == config_size and list(open('.config')) == origconfig:
del config[i]
else:
i += 1
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config)
defconfig.close()
which is pretty self-explanatory.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CPU: Testing write buffer coherency: ok
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:3145 check_flags+0xcc/0x1dc()
Modules linked in:
[<c0035120>] (unwind_backtrace+0x0/0xf8) from [<c0355374>] (dump_stack+0x20/0x24)
[<c0355374>] (dump_stack+0x20/0x24) from [<c0060c04>] (warn_slowpath_common+0x58/0x70)
[<c0060c04>] (warn_slowpath_common+0x58/0x70) from [<c0060c3c>] (warn_slowpath_null+0x20/0x24)
[<c0060c3c>] (warn_slowpath_null+0x20/0x24) from [<c008f224>] (check_flags+0xcc/0x1dc)
[<c008f224>] (check_flags+0xcc/0x1dc) from [<c00945dc>] (lock_acquire+0x50/0x140)
[<c00945dc>] (lock_acquire+0x50/0x140) from [<c0358434>] (_raw_spin_lock+0x50/0x88)
[<c0358434>] (_raw_spin_lock+0x50/0x88) from [<c00fd114>] (set_task_comm+0x2c/0x60)
[<c00fd114>] (set_task_comm+0x2c/0x60) from [<c007e184>] (kthreadd+0x30/0x108)
[<c007e184>] (kthreadd+0x30/0x108) from [<c0030104>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
possible reason: unannotated irqs-on.
irq event stamp: 3
hardirqs last enabled at (2): [<c0059bb0>] finish_task_switch+0x48/0xb0
hardirqs last disabled at (3): [<c002f0b0>] ret_slow_syscall+0xc/0x1c
softirqs last enabled at (0): [<c005f3e0>] copy_process+0x394/0xe5c
softirqs last disabled at (0): [<(null)>] (null)
Fix this by ensuring that the lockdep interrupt state is manipulated in
the appropriate places. We essentially treat userspace as an entirely
separate environment which isn't relevant to lockdep (lockdep doesn't
monitor userspace.) We don't tell lockdep that IRQs will be enabled
in that environment.
Instead, when creating kernel threads (which is a rare event compared
to entering/leaving userspace) we have to update the lockdep state. Do
this by starting threads with IRQs disabled, and in the kthread helper,
tell lockdep that IRQs are enabled, and enable them.
This provides lockdep with a consistent view of the current IRQ state
in kernel space.
This also revert portions of 0d928b0b61
which didn't fix the problem.
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MTU wallclock timing fix-up patch was hardwired to the DB8500
causing a regression. This makes it work on the DB5500 as well.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the 32-bit and 64-bit atomic operations on ARM do not
include memory constraints in the inline assembly blocks. In the
case of barrier-less operations [for example, atomic_add], this
means that the compiler may constant fold values which have actually
been modified by a call to an atomic operation.
This issue can be observed in the atomic64_test routine in
<kernel root>/lib/atomic64_test.c:
00000000 <test_atomic64>:
0: e1a0c00d mov ip, sp
4: e92dd830 push {r4, r5, fp, ip, lr, pc}
8: e24cb004 sub fp, ip, #4
c: e24dd008 sub sp, sp, #8
10: e24b3014 sub r3, fp, #20
14: e30d000d movw r0, #53261 ; 0xd00d
18: e3011337 movw r1, #4919 ; 0x1337
1c: e34c0001 movt r0, #49153 ; 0xc001
20: e34a1aa3 movt r1, #43683 ; 0xaaa3
24: e16300f8 strd r0, [r3, #-8]!
28: e30c0afe movw r0, #51966 ; 0xcafe
2c: e30b1eef movw r1, #48879 ; 0xbeef
30: e34d0eaf movt r0, #57007 ; 0xdeaf
34: e34d1ead movt r1, #57005 ; 0xdead
38: e1b34f9f ldrexd r4, [r3]
3c: e1a34f90 strexd r4, r0, [r3]
40: e3340000 teq r4, #0
44: 1afffffb bne 38 <test_atomic64+0x38>
48: e59f0004 ldr r0, [pc, #4] ; 54 <test_atomic64+0x54>
4c: e3a0101e mov r1, #30
50: ebfffffe bl 0 <__bug>
54: 00000000 .word 0x00000000
The atomic64_set (0x38-0x44) writes to the atomic64_t, but the
compiler doesn't see this, assumes the test condition is always
false and generates an unconditional branch to __bug. The rest of the
test is optimised away.
This patch adds suitable memory constraints to the atomic operations on ARM
to ensure that the compiler is informed of the correct data hazards. We have
to use the "Qo" constraints to avoid hitting the GCC anomaly described at
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=44492 , where the compiler
makes assumptions about the writeback in the addressing mode used by the
inline assembly. These constraints forbid the use of auto{inc,dec} addressing
modes, so it doesn't matter if we don't use the operand exactly once.
Cc: stable@kernel.org
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The atomic64_add_unless function compares an atomic variable with
a given value and, if they are not equal, adds another given value
to the atomic variable. The function returns zero if the addition
did not occur and non-zero otherwise.
On ARM, the return value is initialised to 1 in C code. Inline assembly
code then performs the atomic64_add_unless operation, setting the
return value to 0 iff the addition does not occur. This means that
when the addition *does* occur, the value of ret must be preserved
across the inline assembly and therefore requires a "+r" constraint
rather than the current one of "=&r".
Thanks to Nicolas Pitre for helping to spot this.
Cc: stable@kernel.org
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On i.MX35 the L2X0_AUX_CTRL register does not have sensible reset
default values. Allow them to be overwritten with the aux_val/aux_mask
arguments passed to l2x0_init().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes on wrong function name in include/plat/sdhci.h for Samsung.
The 's5pc100_default_sdhci0()' function should be chnaged to
's5pv210_default_sdhci0()'. Because 's5pv210_default_sdhci0()' must be pair.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S5P6442 PLL setting announce message incorrectly displays S5P6440
as the SoC. Change it to S5P6442.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the following compilation problem if only NCP machine
is selected:
arch/arm/mach-s3c64xx/s3c6410.c: In function 's3c6410_map_io':
arch/arm/mach-s3c64xx/s3c6410.c:51: error: implicit declaration of function 's3c6410_default_sdhci2'
And also adds missed 's3c6400_default_sdhci2'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix and added comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
1. Corrected shift values of I2S and UART clocks (CLK_GATE_IP3), which were
defined incorrectly.
2. Corrected shift values of sclk_audio, uclk1, sclk_fimd, sclk_mmc,
sclk_spi, sclk_pwm, which had duplicated .enable/.ctrlbit with their
twins defined in struct clk init_clocks_disable[] and struct clk
init_clocks[]. We've changed their .enable/.ctrlbit to use CLK_SRC_MASK
register to avoid the duplicated clock problem described below.
NOTE: Duplicated Clock Problem
Please note that each clock definition should access different control
register; otherwise, the system may suffer lockups. For example, if we
have two clock definitions "a" and "b" which access the same register
(and the shift value). Then, when we do:
module A
clk = clk_get("a");
clk->clk_enable(clk);
module B (context switch)
clk = clk_get("b");
clk->clk_enable(clk);
do something with clk.
clk->clk_disable(clk);
module A (context switch)
do something with clk
* At this point, the system may hang.
Therefore, there should be no clock definitions with the same contol
register/shift. If we need to create "aliases", then, creating child
clocks sharing the clock should be fine.
3. Corrected other sclk_* shift values and access registers.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title and message fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Samu Onkalo