The PCI "ACPI additions for FW latency optimizations" ECN (link below)
defines two functions in the PCI _DSM:
Function 8, "Reset Delay," applies to the entire hierarchy below a PCI
host bridge. If it returns one, the OS may assume that all devices in
the hierarchy have already completed power-on reset delays.
Function 9, "Device Readiness Durations," applies only to the object
where it is located. It returns delay durations required after various
events if the device requires less time than the spec requires. Delays
from this function take precedence over the Reset Delay function.
Add support for Reset Delay and part of Device Readiness Durations.
[bhelgaas: changelog, comments]
Link: https://www.pcisig.com/specifications/conventional/pci_firmware/ECN_fw_latency_optimization_final.pdf
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The find_pci_host_bridge() function can be useful to other PCI code so
export it. Change its name to pci_find_host_bridge().
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI Firmware Specification, r3.0, sec 4.6.4.1.3, defines a single UUID
for an ACPI _DSM method to provide device-specific control functions. This
_DSM method support several functions, including PCI Express Slot
Information, PCI Express Slot Number, PCI Bus Capabilities, etc.
Move the UUID definition from pci/pci-label.c, where it could be used only
for one function, to pci/pci-acpi.c where it can be shared for all these
functions.
[bhelgaas: changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use a semicolon, not a comma, to terminate a statement.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the Broadcom iProc PCIe controller.
pcie-iproc.c is the common core driver, and a front-end bus interface needs
to be added to support different bus interfaces.
pcie-iproc-platform.c contains the support for the platform bus interface.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Export the following symbols so they can be referenced by a PCI host bridge
driver compiled as a kernel loadable module:
pci_common_swizzle
pci_create_root_bus
pci_stop_root_bus
pci_remove_root_bus
pci_assign_unassigned_bus_resources
pci_fixup_irqs
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Booting a v3.18 or newer Xen domU kernel with PCI devices passed through
results in an oops (this is a 32-bit 3.13.11 dom0 with a 64-bit 4.4.0
hypervisor and 32-bit domU):
BUG: unable to handle kernel paging request at 0030303e
IP: [<c06ed0e6>] acpi_ns_validate_handle+0x12/0x1a
Call Trace:
[<c06eda4d>] ? acpi_evaluate_object+0x31/0x1fc
[<c06b78e1>] ? pci_get_hp_params+0x111/0x4e0
[<c0407bc7>] ? xen_force_evtchn_callback+0x17/0x30
[<c04085fb>] ? xen_restore_fl_direct_reloc+0x4/0x4
[<c0699d34>] ? pci_device_add+0x24/0x450
Don't look for ACPI configuration information if ACPI has been disabled.
I don't think this is the best fix, because we can boot plain Linux (no
Xen) with "acpi=off", and we don't need this check in pci_get_hp_params().
There should be a better fix that would make Xen domU work the same way.
The domU kernel has ACPI support but it has no AML. There should be a way
to initialize the ACPI data structures so things fail gracefully rather
than oopsing. This is an interim fix to address the regression.
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96301
Reported-by: Michael D Labriola <mlabriol@gdeb.com>
Tested-by: Michael D Labriola <mlabriol@gdeb.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.18+
When sizing and assigning resources, we divide the resources into two
lists: the requested list and the additional list. We don't consider the
alignment of additional VF(n) BAR space.
This is because the alignment required for the VF(n) BAR space is the size
of an individual VF BAR, not the size of the space for *all* VFs. But we
want additional alignment to support partitioning on PowerNV.
Consider the additional IOV BAR alignment when sizing and assigning
resources. When there is not enough system MMIO space to accomodate both
the requested list and the additional list, the PF's IOV BAR alignment will
not contribute to the bridge. When there is enough system MMIO space for
both lists, the additional alignment will contribute to the bridge.
The additional alignment is stored in the min_align of pci_dev_resource,
which is stored in the additional list by add_to_list() at the end of
pbus_size_mem(). The additional alignment is calculated in
pci_resource_alignment(). For an IOV BAR, we have arch dependent function
to get the alignment for different arch.
[bhelgaas: changelog, printk cast]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Per the SR-IOV spec r1.1, sec 3.3.14, the required alignment of a PF's IOV
BAR is the size of an individual VF BAR, and the size consumed is the
individual VF BAR size times NumVFs.
The PowerNV platform has additional alignment requirements to help support
its Partitionable Endpoint device isolation feature (see
Documentation/powerpc/pci_iov_resource_on_powernv.txt).
Add a pcibios_iov_resource_alignment() interface to allow platforms to
request additional alignment.
[bhelgaas: changelog, adapt to reworked pci_sriov_resource_alignment(),
drop "align" parameter]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
VFs are dynamically created when a driver enables them. On some platforms,
like PowerNV, special resources are necessary to enable VFs.
Add platform hooks for enabling and disabling VFs.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV, some resource reservation is needed for SR-IOV VFs that don't
exist at the bootup stage. To do the match between resources and VFs, the
code need to get the VF's BDF in advance.
Rename virtfn_bus() and virtfn_devfn() to pci_iov_virtfn_bus() and
pci_iov_virtfn_devfn() and export them.
[bhelgaas: changelog, make "busnr" int]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An SR-IOV device can change its First VF Offset and VF Stride based on the
values of ARI Capable Hierarchy and NumVFs. The number of buses required
for all VFs is determined by NumVFs, First VF Offset, and VF Stride (see
SR-IOV spec r1.1, sec 2.1.2).
Previously pci_iov_bus_range() computed how many buses would be required by
TotalVFs, but this was based on a single NumVFs value and may not have been
the maximum for all NumVFs configurations.
Iterate over all valid NumVFs and calculate the maximum number of bus
numbers that could ever be required for VFs of this device.
[bhelgaas: changelog, compute busnr of NumVFs, not TotalVFs, remove
kerenl-doc comment marker]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The First VF Offset and VF Stride fields depend on the NumVFs setting, so
refresh the cached fields in struct pci_sriov when updating NumVFs. See
the SR-IOV spec r1.1, sec 3.3.9 and 3.3.10.
[bhelgaas: changelog, remove kernel-doc comment marker]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Most of PCI uses "res = &dev->resource[i]", not "res = dev->resource + i".
Use that style in iov.c also.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we don't store the individual VF BAR size. We calculate it when
needed by dividing the PF's IOV resource size (which contains space for
*all* the VFs) by total_VFs or by reading the BAR in the SR-IOV capability
again.
Keep the individual VF BAR size in struct pci_sriov.barsz[], add
pci_iov_resource_size() to retrieve it, and use that instead of doing the
division or reading the SR-IOV capability BAR.
[bhelgaas: rename to "barsz[]", simplify barsz[] index computation, remove
SR-IOV capability BAR sizing]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we size VF BAR0, VF BAR1, etc., from the SR-IOV Capability of a PF, we
learn the alignment requirement and amount of space consumed by a single
VF. But when VFs are enabled, *each* of the NumVFs consumes that amount of
space, so the total size of the PF resource is "VF BAR size * NumVFs".
Add a printk of the total space consumed by the VFs corresponding to what
we already do for normal non-IOV BARs.
No functional change; new message only.
[bhelgaas: split out into its own patch]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we don't have space for all the bus numbers required to enable VFs,
print the largest bus number required and the range available.
No functional change; improved error message only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Originally, EEH core probes on device_node or pci_dev to populate
EEH devices and PEs, which conflicts with the fact: SRIOV VFs are
usually enabled and created by PF's driver and they don't have the
corresponding device_nodes. Instead, SRIOV VFs have dynamically
created pci_dn, which can be used for EEH probe.
The patch reworks EEH probe for PowerNV and pSeries platforms to
do probing based on pci_dn, instead of pci_dev or device_node any
more.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Intel has verified that there is no peer-to-peer between functions for the
below selection of 82580, 82576, 82575, I350, and 82571 multi-port devices.
This adds the necessary quirks to consider the functions isolated from each
other. 82571 quad-port devices are omitted due to likely lack of
ACS/isolation in the onboard switch, rendering quirks for the downstream
endpoints useless.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: John Ronciak <john.ronciak@intel.com>
Add suspend/resume support for the mvebu PCIe host driver. Without this
commit, the system will panic at resume time when PCIe devices are
connected.
Note that we have to use the ->suspend_noirq() and ->resume_noirq() hooks,
because at resume time, the PCI fixups are done at ->resume_noirq() time,
so the PCIe controller has to be ready at this point.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
* pci/iommu:
of: Calculate device DMA masks based on DT dma-range size
arm: dma-mapping: limit IOMMU mapping size
PCI: Update DMA configuration from DT
of/pci: Add of_pci_dma_configure() to update DMA configuration
PCI: Add helper functions pci_get[put]_host_bridge_device()
of: Fix size when dma-range is not used
of: Move of_dma_configure() to device.c to help re-use
of: iommu: Add ptr to OF node arg to of_iommu_configure()
* pci/resource:
PCI: Fail pci_ioremap_bar() on unassigned resources
PCI: Show driver, BAR#, and resource on pci_ioremap_bar() failure
PCI: Mark invalid BARs as unassigned
PNP: Don't check for overlaps with unassigned PCI BARs
Previously, pci_scan_root_bus() created a root PCI bus, enumerated the
devices on it, and called pci_bus_add_devices(), which made the devices
available for drivers to claim them.
Most callers assigned resources to devices after pci_scan_root_bus()
returns, which may be after drivers have claimed the devices. This is
incorrect; the PCI core should not change device resources while a driver
is managing the device.
Remove pci_bus_add_devices() from pci_scan_root_bus() and do it after any
resource assignment in the callers.
Note that ARM's pci_common_init_dev() already called pci_bus_add_devices()
after pci_scan_root_bus(), so we only need to remove the first call:
pci_common_init_dev
pcibios_init_hw
pci_scan_root_bus
pci_bus_add_devices # first call
pci_bus_assign_resources
pci_bus_add_devices # second call
[bhelgaas: changelog, drop "root_bus" var in alpha common_init_pci(),
return failure earlier in mn10300, add "return" in x86 pcibios_scan_root(),
return early if xtensa platform_pcibios_fixup() fails]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Matt Turner <mattst88@gmail.com>
CC: David Howells <dhowells@redhat.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Michal Simek <monstr@monstr.eu>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Chris Metcalf <cmetcalf@ezchip.com>
CC: Chris Zankel <chris@zankel.net>
CC: Max Filippov <jcmvbkbc@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Make pci_ioremap_bar() fail if we're trying to map a BAR that hasn't been
assigned.
Normally pci_enable_device() will fail if a BAR hasn't been assigned, but a
driver can successfully call pci_enable_device_io() even if a memory BAR
hasn't been assigned. That driver should not be able to use
pci_ioremap_bar() to map that unassigned memory BAR.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use dev_warn() to complain about a pci_ioremap_bar() failure so we can
include the driver name, BAR number, and the resource itself. We could use
dev_WARN() to also get the backtrace as we did previously, but I think
that's more information than we need.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a BAR is not inside any upstream bridge window, or if it conflicts with
another resource, mark it as IORESOURCE_UNSET so we don't try to use it.
We may be able to assign a different address for it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Previously, pci_scan_bus() created a root PCI bus, enumerated the devices
on it, and called pci_bus_add_devices(), which made the devices available
for drivers to claim them.
Most callers assigned resources to devices after pci_scan_bus() returns,
which may be after drivers have claimed the devices. This is incorrect;
the PCI core should not change device resources while a driver is managing
the device.
Remove pci_bus_add_devices() from pci_scan_bus() and do it after any
resource assignment in the callers.
[bhelgaas: changelog, check for failure in mcf_pci_init()]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Guan Xuetao <gxt@mprc.pku.edu.cn>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Matt Turner <mattst88@gmail.com>
APM X-Gene host bridge driver
- Add register offset to config space base address (Feng Kan)
Miscellaneous
- Don't read past the end of sysfs "driver_override" buffer (Sasha Levin)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4mzw
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.0-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a couple updates for v4.0.
One fixes a config accessor problem on APM X-Gene that we introduced
when switching to generic config accessors, and the other fixes an
older read-past-end-of-buffer problem in sysfs.
APM X-Gene host bridge driver
- Add register offset to config space base address (Feng Kan)
Miscellaneous
- Don't read past the end of sysfs "driver_override" buffer (Sasha Levin)"
* tag 'pci-v4.0-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: xgene: Add register offset to config space base address
PCI: Don't read past the end of sysfs "driver_override" buffer
If there is a DT node available for the root bridge's parent device, use
the DMA configuration from that device node. For example, Keystone PCI
devices would require dma_pfn_offset to be set correctly in the device
structure of the PCI device in order to have the correct DMA mask. The DT
node will have dma-ranges defined for this. Also support using the DT
property dma-coherent to allow coherent DMA operation by the PCI device.
Use the new helper function of_pci_dma_configure() to update the device DMA
configuration. This fixes DMA on systems where DMA addresses are a
constant offset from CPU physical addresses.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
I don't have this hardware but it looks like we weren't adding bridge
devices as intended. Maybe the bridge is always the last device?
Fixes: 05b1250048 ("PCI: cpcihp: Iterate over all devices in slot, not functions 0-7")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yijing Wang <wangyijing@huawei.com>
CC: stable@vger.kernel.org # v3.9+
Commit fab4c256a5 ("PCI/AER: Add a TLP header print helper") introduced
the helper function __print_tlp_header(), but contrary to the intention,
the behaviour did change: Since we're taking the address of the parameter
t, the first 4 or 8 bytes printed will be the value of the pointer t
itself, and the remaining 12 or 8 bytes will be who-knows-what (something
from the stack).
We want to show the values of the four members of the struct
aer_header_log_regs; that can be done without ugly and error-prone casts.
On little-endian this should produce the same output as originally
intended, and since no-one has complained about getting garbage output so
far, I think big-endian should be ok too.
Fixes: fab4c256a5 ("PCI/AER: Add a TLP header print helper")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Borislav Petkov <bp@suse.de>
CC: stable@vger.kernel.org # v3.14+
Struct spear13xx_pcie_driver was in initdata, but we passed a pointer to it
to platform_driver_register(), which can use the pointer at arbitrary times
in the future, even after the initdata is freed. That leads to crashes.
Move spear13xx_pcie_driver and things referenced by it
(spear13xx_pcie_probe() and dw_pcie_host_init()) out of initdata.
[bhelgaas: changelog]
Fixes: 6675ef212d ("PCI: spear: Fix Section mismatch compilation warning for probe()")
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
CC: stable@vger.kernel.org # v3.17+
In xgene_pcie_map_bus(), we neglected to add in the register offset when
calculating the config space address. This means all config accesses
operated on the first four bytes of config space.
Add the register offset to the config space base address.
Also correct the xgene_pcie_map_bus() prototype to fix a compiler warning.
[bhelgaas: changelog]
Fixes: 350f8be5bb ("PCI: xgene: Convert to use generic config accessors")
Posting: http://lkml.kernel.org/r/1424214840-26498-1-git-send-email-fkan@apm.com
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
In Linux 4.0-rc1 ARM Versatile PCI build fails to build due to what
appears to be an API update. This patch is a very simple correction,
merely posted as a heads-up to the maintainers. Hopefully a better
fix can be forwarded to Linus.
[ arnd: the patch actually looks correct, so let's take this version ]
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When printing the driver_override parameter when it is 4095 and 4094 bytes
long, the printing code would access invalid memory because we need count+1
bytes for printing.
Fixes: 782a985d7a ("PCI: Introduce new device binding path using pci_dev.driver_override")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
CC: stable@vger.kernel.org # v3.16+
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Alexander Graf <agraf@suse.de>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lower 16 bits of the address, which is managed by mem_res, need to be
zero. Check the address to verify this.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
PCIEPARL and PCIEPARH are macros that calculate register addresses.
However, the register names are incorrect. Change them to PCIEPALR and
PCIEPAUR.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The lower 7 bits of PCIEPARL are reserved. When we write to this register,
these bits must be 0.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The MSI enable is bit 31, not bit 28. Set the correct bit to initialize
MSI.
Per Phil, "this is odd as MSI works before and after your patch. Since bit
31 just represents the value of MSICAP0[16].MSIE, I think this may just be
used for endpoints. However, you are correct that the bit used was wrong."
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
- Rework of the core ACPI resources parsing code to fix issues
in it and make using resource offsets more convenient and
consolidation of some resource-handing code in a couple of places
that have grown analagous data structures and code to cover the
the same gap in the core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus,
Jarkko Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states
to make the code more straightforward and less bloated overall
(Rafael J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki,
Yaowei Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in
the right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist,
Pavel Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zZER
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"We have a few new features this time, including a new SFI-based
cpufreq driver, a new devfreq driver for Tegra Activity Monitor, a new
devfreq class for providing its governors with raw utilization data
and a new ACPI driver for AMD SoCs.
Still, the majority of changes here are reworks of existing code to
make it more straightforward or to prepare it for implementing new
features on top of it. The primary example is the rework of ACPI
resources handling from Jiang Liu, Thomas Gleixner and Lv Zheng with
support for IOAPIC hotplug implemented on top of it, but there is
quite a number of changes of this kind in the cpufreq core, ACPICA,
ACPI EC driver, ACPI processor driver and the generic power domains
core code too.
The most active developer is Viresh Kumar with his cpufreq changes.
Specifics:
- Rework of the core ACPI resources parsing code to fix issues in it
and make using resource offsets more convenient and consolidation
of some resource-handing code in a couple of places that have grown
analagous data structures and code to cover the the same gap in the
core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus, Jarkko
Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states to
make the code more straightforward and less bloated overall (Rafael
J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki, Yaowei
Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in the
right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist, Pavel
Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan)"
* tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (151 commits)
tools/power turbostat: relax dependency on APERF_MSR
tools/power turbostat: relax dependency on invariant TSC
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
tools/power turbostat: decode MSR_*_PERF_LIMIT_REASONS
tools/power turbostat: relax dependency on root permission
ACPI / video: Add disable_native_backlight quirk for Samsung 510R
ACPI / PM: Remove unneeded nested #ifdef
USB / PM: Remove unneeded #ifdef and associated dead code
intel_pstate: provide option to only use intel_pstate with HWP
ACPI / EC: Add GPE reference counting debugging messages
ACPI / EC: Add query flushing support
ACPI / EC: Refine command storm prevention support
ACPI / EC: Add command flushing support.
ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag
ACPI: add AMD ACPI2Platform device support for x86 system
ACPI / table: remove duplicate NULL check for the handler of acpi_table_parse()
ACPI / EC: Update revision due to raw handler mode.
ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
...
* acpi-resources: (23 commits)
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
x86/irq, ACPI: Implement ACPI driver to support IOAPIC hotplug
ACPI: Add interfaces to parse IOAPIC ID for IOAPIC hotplug
x86/PCI: Refine the way to release PCI IRQ resources
x86/PCI/ACPI: Use common ACPI resource interfaces to simplify implementation
x86/PCI: Fix the range check for IO resources
PCI: Use common resource list management code instead of private implementation
resources: Move struct resource_list_entry from ACPI into resource core
ACPI: Introduce helper function acpi_dev_filter_resource_type()
ACPI: Add field offset to struct resource_list_entry
ACPI: Translate resource into master side address for bridge window resources
ACPI: Return translation offset when parsing ACPI address space resources
ACPI: Enforce stricter checks for address space descriptors
ACPI: Set flag IORESOURCE_UNSET for unassigned resources
ACPI: Normalize return value of resource parser functions
ACPI: Fix a bug in parsing ACPI Memory24 resource
ACPI: Add prefetch decoding to the address space parser
ACPI: Move the window flag logic to the combined parser
ACPI: Unify the parsing of address_space and ext_address_space
ACPI: Let the parser return false for disabled resources
...
* acpica:
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
ACPICA: Events: Introduce acpi_set_gpe()/acpi_finish_gpe() to reduce divergences
ACPICA: Events: Introduce ACPI_GPE_DISPATCH_RAW_HANDLER to fix 2 issues for the current GPE APIs
ACPICA: Update version to 20150204
ACPICA: Update Copyright headers to 2015
ACPICA: Hardware: Cast GPE enable_mask before storing
ACPICA: Events: Cleanup GPE dispatcher type obtaining code
ACPICA: Events: Cleanup to move acpi_gbl_global_event_handler invocation out of acpi_ev_gpe_dispatch()
ACPICA: Events: Cleanup of resetting the GPE handler to NULL before removing
ACPICA: Events: Fix uninitialized variable
ACPICA: Events: Remove acpi_ev_valid_gpe_event() due to current restriction
ACPICA: Events: Remove duplicated sanity check in acpi_ev_enable_gpe()
ACPICA: Events: Back port "ACPICA: Save current masks of enabled GPEs after enable register writes"
ACPICA: Resources: Provide common part for struct acpi_resource_address structures.
ACPI: Introduce acpi_unload_parent_table() usages in Linux kernel
ACPICA: take ACPI_MTX_INTERPRETER in acpi_unload_table_id()
Use common resource list management data structure and interfaces
instead of private implementation.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some AMD CS553x devices have read-only BARs because of a firmware or
hardware defect. There's a workaround in quirk_cs5536_vsa(), but it no
longer works after 36e8164882 ("PCI: Restore detection of read-only
BARs"). Prior to 36e8164882, we filled in res->start; afterwards we
leave it zeroed out. The quirk only updated the size, so the driver tried
to use a region starting at zero, which didn't work.
Expand quirk_cs5536_vsa() to read the base addresses from the BARs and
hard-code the sizes.
On Nix's system BAR 2's read-only value is 0x6200. Prior to 36e8164882,
we interpret that as a 512-byte BAR based on the lowest-order bit set. Per
datasheet sec 5.6.1, that BAR (MFGPT) requires only 64 bytes; use that to
avoid clearing any address bits if a platform uses only 64-byte alignment.
[bhelgaas: changelog, reduce BAR 2 size to 64]
Fixes: 36e8164882 ("PCI: Restore detection of read-only BARs")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85991#c4
Link: http://support.amd.com/TechDocs/31506_cs5535_databook.pdf
Link: http://support.amd.com/TechDocs/33238G_cs5536_db.pdf
Reported-and-tested-by: Nix <nix@esperi.org.uk>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v.2.6.27+
* pci/misc:
r8169: use PCI define for Max_Read_Request_Size
[SCSI] esas2r: use PCI define for Max_Read_Request_Size
tile: use PCI define for Max_Read_Request_Size
rapidio/tsi721: use PCI define for Max_Read_Request_Size
PCI: Add defines for PCIe Max_Read_Request_Size
PCI/ASPM: Use standard parsing functions for sysfs setters
* pci/msi:
PCI: Fail MSI-X mappings if there's no space assigned to MSI-X BAR
* pci/config:
PCI: xilinx: Convert to use generic config accessors
PCI: xgene: Convert to use generic config accessors
PCI: tegra: Convert to use generic config accessors
PCI: rcar: Convert to use generic config accessors
PCI: generic: Convert to use generic config accessors
powerpc/powermac: Convert PCI to use generic config accessors
powerpc/fsl_pci: Convert PCI to use generic config accessors
ARM: ks8695: Convert PCI to use generic config accessors
ARM: sa1100: Convert PCI to use generic config accessors
ARM: integrator: Convert PCI to use generic config accessors
ARM: cns3xxx: Convert PCI to use generic config accessors
PCI: Add generic config accessors
powerpc/PCI: Add struct pci_ops member names to initialization
mn10300/PCI: Add struct pci_ops member names to initialization
MIPS: PCI: Add struct pci_ops member names to initialization
frv/PCI: Add struct pci_ops member names to initialization
Convert the rcar-gen2 host PCI driver to use the generic config access
functions.
This changes the I/O accessors from io(read|write)X to readX/writeX
variants which are equivalent on ARM.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
CC: Simon Horman <horms@verge.net.au>
CC: linux-sh@vger.kernel.org
Convert the generic host PCI driver to use the generic config access
functions.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: linux-arm-kernel@lists.infradead.org
This converts the Versatile PCI host code to a platform driver using the
commom DT parsing and setup. The driver uses only an empty ARM
pci_sys_data struct and does not use pci_common_init_dev init function.
The old host code will be removed in a subsequent commit when Versatile is
completely converted to DT.
I've tested this on QEMU with the sym53c8xx driver in both i/o and memory
mapped modes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Peter Maydell <peter.maydell@linaro.org>
Unlike MSI, which is configured via registers in the MSI capability in
Configuration Space, MSI-X is configured via tables in Memory Space.
These MSI-X tables are mapped by a device BAR, and if no Memory Space
has been assigned to the BAR, MSI-X cannot be used.
Fail MSI-X setup if no space has been assigned for the BAR.
Previously, we ioremapped the MSI-X table even if the resource hadn't been
assigned. In this case, the resource address is undefined (and is often
zero), which may lead to warnings or oopses in this path:
pci_enable_msix
msix_capability_init
msix_map_region
ioremap_nocache
The PCI core sets resource flags to zero when it can't assign space for the
resource (see reset_resource()). There are also some cases where it sets
the IORESOURCE_UNSET flag, e.g., pci_reassigndev_resource_alignment(),
pci_assign_resource(), etc. So we must check for both cases.
[bhelgaas: changelog]
Reported-by: Zhang Jukuo <zhangjukuo@huawei.com>
Tested-by: Zhang Jukuo <zhangjukuo@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/enumeration:
PCI: Generate uppercase hex for modalias var in uevent
* pci/hotplug:
PCI: pciehp: Handle surprise add even if surprise removal isn't supported
* pci/resource:
PCI: Fix infinite loop with ROM image of size 0
* pci/virtualization:
PCI: Add Wellsburg (X99) to Intel PCH root port ACS quirk
PCI: Add DMA alias quirk for Adaptec 3405
PCI: Add ACS quirk for Emulex NICs
PCI: Mark AMD/ATI VGA devices that don't reset on D3hot->D0 transition
PCI: Add flag for devices that don't reset on D3hot->D0 transition
PCI: Mark Atheros AR93xx to avoid bus reset
PCI: Add flag for devices where we can't use bus reset
The DesignWare PCIe MSI hardware does not support MSI-X IRQs. Setting
those up failed as a side effect of a bug which was fixed by 91f8ae823f
("PCI: designware: Setup and clear exactly one MSI at a time").
Now that this bug is fixed, MSI-X IRQs need to be rejected explicitly;
otherwise devices trying to use them may end up with incorrectly working
interrupts.
Fixes: 91f8ae823f ("PCI: designware: Setup and clear exactly one MSI at a time")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
CC: stable@vger.kernel.org # v3.18+
ACPICA has implemented acpi_unload_parent_table() which can exactly replace
the acpi_get_id()/acpi_unload_table_id() implemented in Linux kernel. The
acpi_unload_parent_table() has been unit tested in ACPICA simulation
environment.
This patch can also help to reduce the source code differences between
Linux and ACPICA.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the image size would ever read as 0, pci_get_rom_size() could keep
processing the same image over and over again. Exit the loop if we ever
read a length of zero.
This fixes a soft lockup on boot when the radeon driver calls
pci_get_rom_size() on an AMD Radeon R7 250X PCIe discrete graphics card.
[bhelgaas: changelog, reference]
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1386973
Reported-by: Federico <federicotg@gmail.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
This driver should be including clk.h as it's a clock consumer, not a clock
provider that needs to register clocks early.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
Intel has confirmed that the Wellsburg chipset, while not reporting ACS,
does provide the proper isolation through the RCBA/BSPR registers, so the
same quirk works for this set of device IDs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
The Adaptec 3405 is actually an Intel 80333 I/O processor where the exposed
device at 0e.0 is actually the address translation unit of the I/O
processor and a hidden, private device at 01.0 masters the DMA for the
device. Create a fixed alias between the exposed and hidden devfn so we
can enable the IOMMU.
Scenarios like this are potentially likely for any device incorporating
this I/O processor, so this little bit of abstraction with the fixed alias
table should make future additions trivial.
Without this fix, booting a system with the Intel IOMMU enabled and an
Adaptec 3405 at 02:0e.0 results in a flood of errors like this:
dmar: DRHD: handling fault status reg 3
dmar: DMAR:[DMA Write] Request device [02:01.0] fault addr ffbff000
DMAR:[fault reason 02] Present bit in context entry is clear
[bhelgaas: changelog, comment]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Adaptec OEM Raid Solutions <aacraid@adaptec.com>
The xilinx PCIe driver prints a register value whose type is propagated to
the type returned by the GENMASK() macro. Unfortunately, that type has
recently changed as the result of a bug fix, so now we get a warning about
the type:
drivers/pci/host/pcie-xilinx.c: In function 'xilinx_pcie_clear_err_interrupts':
drivers/pci/host/pcie-xilinx.c:154:3: warning: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Wformat=]
Change the code so we always print the number as an 'unsigned long' type to
avoid the warning. The original code was fine on 32-bit architectures but
not on 64-bit. Now it works as expected on both.
Fixes: 00b4d9a141 ("bitops: Fix shift overflow in GENMASK macros")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Commit f25c0ae2b4 (ACPI / PM: Avoid resuming devices in ACPI PM
domain during system suspend) modified the ACPI PM domain's system
suspend callbacks to allow devices attached to it to be left in the
runtime-suspended state during system suspend so as to optimize
the suspend process.
This was based on the general mechanism introduced by commit
aae4518b31 (PM / sleep: Mechanism to avoid resuming runtime-suspended
devices unnecessarily).
Extend that approach to PCI devices by modifying the PCI bus type's
->prepare callback to return 1 for devices that are runtime-suspended
when it is being executed and that are in a suitable power state and
need not be resumed going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Many PCI controllers' configuration space accesses are memory-mapped and
vary only in address calculation and access checks. There are 2 main
access methods: a decoded address space such as ECAM or a single address
and data register similar to x86. This implementation can support both
cases as well as be used in cases that need additional pre- or post-access
handling.
Add a new pci_ops member, map_bus, which can do access checks and any
necessary setup. It returns the address to use for the configuration space
access. The access types supported are 32-bit only accesses or correct
byte, word, or dword sized accesses.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The PCIe spec (r3.0, sec 7.8.9) says Hot-Plug Surprise indicates support
for surprise *removal*, but pciehp checked this to determine if it should
handle presence detect interrupts for device *addition*.
Allow surprise device addition even if the slot doesn't advertise support
for surprise removal.
Keith has a platform with slots for front-loading SFF devices. The slots
do not have attention buttons and do not support surprise removal, but they
do have presence detect. In that case, we still want to use presence
detect for device addition.
Keith's original patch handled surprise insertions only if Hot-Plug Capable
is set. I think that test is superfluous because pciehp only claims slots
that advertise Hot-Plug Capable (see get_port_device_capability()).
Link: http://lkml.kernel.org/r/1419275223-14602-1-git-send-email-keith.busch@intel.com
Based-on-patch-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rajat Jain <rajatxjain@gmail.com>
As Skyhawk and BE3-R (both multi-function devices) don't advertise the
PCI-ACS capability, the vfio driver places all the functions of these
devices in a single IOMMU group. Attaching (via PCI-passthru) two
different Skyhawk/BE3-R partitions (nPAR, Flex, etc. PFs) using vfio, to
different guests doesn't work as vfio only allows functions in *different*
IOMMU groups to be assigned to different guests.
As peer-to-peer access between PFs in Skyhawk/BE3-R is not possible, we can
treat them as "fully isolated" even though the device doesn't advertise
ACS. Add a PCI quirk for Skyhawk and BE3-R chips to fix this problem.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Some AMD/ATI GPUs report NoSoftRst- to indicate that they perform a reset
when software transitions them from D3hot to D0, but there is no apparent
effect on the device: the monitor remains synced and the framebuffer
contents are retained.
Callers of pci_reset_function() don't necessarily have a way to validate
whether a reset was effective, so we don't want to rely on NoSoftRst if
it's known to be inaccurate. Returning an error in such cases appears to
be the better option. For users like vfio-pci, this allows the driver to
escalate to the bus reset interfaces.
If a device lives on the root bus, there's really no further
escalation path, so we exempt PM reset as potentially better than
nothing.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Per the PCI Power Management spec r1.2, sec 3.2.4, a device that advertises
No_Soft_Reset == 0 in the PMCSR register (reported by lspci as "NoSoftRst-")
should perform an internal reset when transitioning from D3hot to D0 via
software control. Configuration context is lost and the device requires a
full reinitialization sequence.
Unfortunately the definition of "internal reset", beyond the application of
the configuration context, is largely left to the interpretation of the
specific device. Some devices don't seem to perform an "internal reset"
even if they report No_Soft_Reset == 0.
We still need to honor the PCI specification and restore PCI config context
in the event that we do a PM reset, so we don't cache and modify the
PCI_PM_CTRL_NO_SOFT_RESET bit for the device, but for interfaces where the
intention is to reset the device, like pci_reset_function(), we need a
mechanism to flag that PM reset (a D3hot->D0 transition) doesn't perform
any significant "internal reset" of the device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_claim_bridge_resource() to claim a PCI-PCI bridge window. This is
like regular pci_claim_resource(), except that if we fail to claim the
window, we check to see if we can reduce the size of the window and try
again.
This is for scenarios like this:
pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff]
pci 0000:00:01.0: bridge window [mem 0xbdf00000-0xddefffff 64bit pref]
pci 0000:01:00.0: reg 0x10: [mem 0xc0000000-0xcfffffff pref]
The 00:01.0 window is illegal: it starts before the host bridge window, so
we have to assume the [0xbdf00000-0xbfffffff] region is inaccessible. We
can make it legal by clipping it to [mem 0xc0000000-0xddefffff 64bit pref].
Previously we discarded the 00:01.0 window and tried to reassign that part
of the hierarchy from scratch. That is a problem because Linux doesn't
always assign things optimally. For example, in this case, BIOS put the
01:00.0 device in a prefetchable window below 4GB, but after 5b28541552,
Linux puts the prefetchable window above 4GB where the 32-bit 01:00.0
device can't use it.
Clipping the 00:01.0 window is less intrusive than completely reassigning
things and is sufficient to let us use most of the BIOS configuration. Of
course, it's possible that devices below 00:01.0 will no longer fit. If
that's the case, we'll have to reassign things. But that's a separate
problem.
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
Add pci_bus_clip_resource(). If a PCI-PCI bridge window overlaps an
upstream bridge window but is not completely contained by it, this clips
the downstream window so it fits inside the upstream one.
No functional change (this adds the function but no callers).
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
pci_setup_bridge_io(), pci_setup_bridge_mmio(), and
pci_setup_bridge_mmio_pref() program the windows of PCI-PCI bridges.
Previously they accepted a pointer to the pci_bus of the secondary bus,
then looked up the bridge leading to that bus. Pass the bridge directly,
which will make it more convenient for future callers.
No functional change.
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
Reports against the TL-WDN4800 card indicate that PCI bus reset of this
Atheros device cause system lock-ups and resets. I've also been able to
confirm this behavior on multiple systems. The device never returns from
reset and attempts to access config space of the device after reset result
in hangs. Blacklist bus reset for the device to avoid this issue.
[bhelgaas: This regression appeared in v3.14. Andreas bisected it to
425c1b223d ("PCI: Add Virtual Channel to save/restore support"), but we
don't understand the mechanism by which that commit affects the reset
path.]
[bhelgaas: changelog, references]
Link: http://lkml.kernel.org/r/20140923210318.498dacbd@dualc.maya.org
Reported-by: Andreas Hartmann <andihartmann@freenet.de>
Tested-by: Andreas Hartmann <andihartmann@freenet.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
Enable a mechanism for devices to quirk that they do not behave when
doing a PCI bus reset. We require a modest level of spec compliant
behavior in order to do a reset, for instance the device should come
out of reset without throwing errors and PCI config space should be
accessible after reset. This is too much to ask for some devices.
Link: http://lkml.kernel.org/r/20140923210318.498dacbd@dualc.maya.org
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
Replace a misspelled function name by %s and then __func__.
The function name contains pcie, not pci as in the string.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
The functions link_state_store() and clk_ctl_store() had just subtracted
ASCII '0' from input which could lead to undesired results. Instead, use
Linux string functions to safely parse input.
[bhelgaas: check kstrtouint() return value]
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.
The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D. Most interface types defined in the spec do not use
alpha characters, so they won't be affected. For example, 00h, 01h, 10h,
20h, etc. are unaffected.
Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.
Commit 89ec3dcf17 ("PCI: Generate uppercase hex for modalias interface
class") fixed only half of the problem. Some udev implementations rely on
the uevent file and not the modalias file.
Fixes: d1ded203ad ("PCI: add MODALIAS to hotplug event for pci devices")
Fixes: 89ec3dcf17 ("PCI: Generate uppercase hex for modalias interface class")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: stable@vger.kernel.org
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Most if not all ARM PCI host controller device drivers either ignore the
domain field in the pci_sys_data structure or just increment it every time
a host controller is probed, using it as a domain counter.
Therefore, instead of relying on pci_sys_data to stash the domain number in
a standard location, ARM pcibios code can be moved to the newly introduced
generic PCI domains code, implemented in commits:
41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()")
670ba0c888 ("PCI: Add generic domain handling")
ARM code is made to select PCI_DOMAINS_GENERIC by default, which builds
core PCI code that assigns the domain number through the generic function:
void pci_bus_assign_domain_nr(...)
that relies on a DT property to define the domain number or falls back to a
counter according to a predefined logic; its usage replaces the current
domain assignment code in PCI host controllers present in the kernel.
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> # mvebu
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Mohit Kumar <mohit.kumar@st.com>
The current logic in arm64 pci_bus_assign_domain_nr() is flawed in that
depending on the host controller configuration for a platform and the
initialization sequence, core code may end up allocating PCI domain numbers
from both DT and the generic domain counter, which would result in PCI
domain allocation aliases/errors.
Fix the logic behind the PCI domain number assignment and move the
resulting code to the PCI core so the same domain allocation logic is used
on all platforms that select CONFIG_PCI_DOMAINS_GENERIC.
[bhelgaas: tidy changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Rob Herring <robh+dt@kernel.org>
CC: Catalin Marinas <catalin.marinas@arm.com>
The pci_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The bridge setup is already done by generic code while scanning the buses.
Do not duplicate (or potentially alter) this setup as a fixup.
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The bridge setup is already done by generic code while scanning the buses.
Do not duplicate (or potentially alter) this setup as a fixup.
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
No need to set .owner here. The core will do it.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Return value of irq_of_parse_and_map() is unsigned int, with 0 indicating
failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
Return value of irq_of_parse_and_map() is unsigned int, with 0 indicating
failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
Now we have splitted functions to support MSI and HT_IRQ into vector.c,
and they have no dependency on IOAPIC any more. So change Kconfig files
to make MSI and HT_IRQ independent of X86_IO_APIC.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1414397531-28254-16-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Clean up code by moving IOAPIC related declarations from hw_irq.h into
io_apic.h.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Aubrey <aubrey.li@linux.intel.com>
Cc: Ryan Desfosses <ryan@desfo.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1414397531-28254-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
None of the callers requires irq_attr to be filled
in. IO_APIC_get_PCI_irq_vector() does not do anything useful with it
either.
Remove the parameter and fixup the call sites.
[ tglx: Massaged changelog ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Ryan Desfosses <ryan@desfo.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1414397531-28254-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To support IOAPIC hotplug on x86 and IA64 platforms, OS needs to figure
out global interrupt source number(GSI) and IOAPIC enumeration ID
through ACPI interfaces. So BIOS must implement an ACPI IOAPIC device
with _GSB/_UID or _MAT method to support IOAPIC hotplug. OS also needs
to figure out base physical address to access IOAPIC registers. OS may
get the base physical address through PCI BARs if IOAPIC device is
visible in PCI domain, otherwise OS may get the address by ACPI _CRS
method if IOAPIC device is hidden from PCI domain by BIOS.
When adding a PCI subtree, we need to add IOAPIC devices before enabling
all other PCI devices because other PCI devices may use the IOAPIC to
allocate PCI interrupts.
So we plan to reimplement IOAPIC driver as an ACPI instead of PCI driver
due to:
1) hot-pluggable IOAPIC devices are always visible in ACPI domain,
but may or may not be visible in PCI domain.
2) we could explicitly control the order between IOAPIC and other PCI
devices.
We also have another choice to use a PCI driver to manage IOAPIC device
if it's visible in PCI domain and use an ACPI driver if it's only
visible in ACPI domain. But this solution is a little complex.
It shouldn't cause serious backward compatibility issues because:
1) IOAPIC hotplug is never supported on x86 yet because it hasn't
implemented the required acpi_register_ioapic() and
acpi_unregister_ioapic().
2) Currently only ACPI based IOAPIC hotplug is possible on x86 and
IA64, we don't know other specifications and interfaces to support
IOAPIC hotplug yet.
3) We will reimplement an ACPI IOAPIC driver to support IOAPIC hotplug.
This change also helps to get rid of the false alarm on all current
Linux distributions:
[ 6.952497] ioapic: probe of 0000:00:05.4 failed with error -22
[ 6.959542] ioapic: probe of 0000:80:05.4 failed with error -22
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1414387308-27148-9-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci and
other individual USB driver updates. The PHY tree is also in here, as
there were dependancies on the USB tree.
All of these have been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOEHcACgkQMUfUDdst+ykziQCgsm1D/af2nac6CTF2pov8VMIY
ywgAnRi8LtZ2WassrwTNxY86Avaqryis
=UVp8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUiYb+AAoJEFxbo/MsZsTRwmEH+gNaJz5r8gIJlq8Q51+nOIs4
Gw6HdjUB5MOT47vDV4treEOx0Bk8hYTfgWUWvAC81JMJ1sMWOVrUGuG/0lmzaomW
zXvSk+o0n4LafwEhHb8LIccZMbaH7f9o3PNdNchrTkPrIl8Gf2nmBXCkDsT4mRye
5ZFpc4ntgBrznh3baPYDS8PCAmlyZ0uVEnz1ofYI6S80dC13siEiPG0c9TrNEKzO
glhvgCRmR0C4ZNLblM36HWBEqrdLuGCoNJSH+7okygyP2TLD3aO4R+9aD5JWYNdf
fO2WmivX/zK+UGVAElrLx+rb8R2dv3ddeaE5piZhIBUieopIWJd32L3LhQORdtc=
=N6DP
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
* tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (26 commits)
Revert "swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single"
xen/pci: Use APIC directly when APIC virtualization hardware is available
xen/pci: Defer initialization of MSI ops on HVM guests
xen-pciback: drop SR-IOV VFs when PF driver unloads
xen/pciback: Restore configuration space when detaching from a guest.
PCI: Expose pci_load_saved_state for public consumption.
xen/pciback: Remove tons of dereferences
xen/pciback: Print out the domain owning the device.
xen/pciback: Include the domain id if removing the device whilst still in use
driver core: Provide an wrapper around the mutex to do lockdep warnings
xen/pciback: Don't deadlock when unbinding.
swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single
swiotlb-xen: call xen_dma_sync_single_for_device when appropriate
swiotlb-xen: remove BUG_ON in xen_bus_to_phys
swiotlb-xen: pass dev_addr to xen_dma_unmap_page and xen_dma_sync_single_for_cpu
xen/arm: introduce GNTTABOP_cache_flush
xen/arm/arm64: introduce xen_arch_need_swiotlb
xen/arm/arm64: merge xen/mm32.c into xen/mm.c
xen/arm: use hypercall to flush caches in map_page
xen: add a dma_addr_t dev_addr argument to xen_dma_map_page
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Pull irq domain updates from Thomas Gleixner:
"The real interesting irq updates:
- Support for hierarchical irq domains:
For complex interrupt routing scenarios where more than one
interrupt related chip is involved we had no proper representation
in the generic interrupt infrastructure so far. That made people
implement rather ugly constructs in their nested irq chip
implementations. The main offenders are x86 and arm/gic.
To distangle that mess we have now hierarchical irqdomains which
seperate the various interrupt chips and connect them via the
hierarchical domains. That keeps the domain specific details
internal to the particular hierarchy level and removes the
criss/cross referencing of chip internals. The resulting hierarchy
for a complex x86 system will look like this:
vector mapped: 74
msi-0 mapped: 2
dmar-ir-1 mapped: 69
ioapic-1 mapped: 4
ioapic-0 mapped: 20
pci-msi-2 mapped: 45
dmar-ir-0 mapped: 3
ioapic-2 mapped: 1
pci-msi-1 mapped: 2
htirq mapped: 0
Neither ioapic nor pci-msi know about the dmar interrupt remapping
between themself and the vector domain. If interrupt remapping is
disabled ioapic and pci-msi become direct childs of the vector
domain.
In hindsight we should have done that years ago, but in hindsight
we always know better :)
- Support for generic MSI interrupt domain handling
We have more and more non PCI related MSI interrupts, so providing
a generic infrastructure for this is better than having all
affected architectures implementing their own private hacks.
- Support for PCI-MSI interrupt domain handling, based on the generic
MSI support.
This part carries the pci/msi branch from Bjorn Helgaas pci tree to
avoid a massive conflict. The PCI/MSI parts are acked by Bjorn.
I have two more branches on top of this. The full conversion of x86
to hierarchical domains and a partial conversion of arm/gic"
* 'irq-irqdomain-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
genirq: Move irq_chip_write_msi_msg() helper to core
PCI/MSI: Allow an msi_controller to be associated to an irq domain
PCI/MSI: Provide mechanism to alloc/free MSI/MSIX interrupt from irqdomain
PCI/MSI: Enhance core to support hierarchy irqdomain
PCI/MSI: Move cached entry functions to irq core
genirq: Provide default callbacks for msi_domain_ops
genirq: Introduce msi_domain_alloc/free_irqs()
asm-generic: Add msi.h
genirq: Add generic msi irq domain support
genirq: Introduce callback irq_chip.irq_write_msi_msg
genirq: Work around __irq_set_handler vs stacked domains ordering issues
irqdomain: Introduce helper function irq_domain_add_hierarchy()
irqdomain: Implement a method to automatically call parent domains alloc/free
genirq: Introduce helper irq_domain_set_info() to reduce duplicated code
genirq: Split out flow handler typedefs into seperate header file
genirq: Add IRQ_SET_MASK_OK_DONE to support stacked irqchip
genirq: Introduce irq_chip.irq_compose_msi_msg() to support stacked irqchip
genirq: Add more helper functions to support stacked irq_chip
genirq: Introduce helper functions to support stacked irq_chip
irqdomain: Do irq_find_mapping and set_type for hierarchy irqdomain in case OF
...
We have the pci_load_and_free_saved_state, and pci_store_saved_state
but are missing the functionality to just load the state
multiple times in the PCI device without having to free/save
the state.
This patch makes it possible to use this function.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PCI core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
NVIDIA Tegra
- Use physical range for I/O mapping (Thierry Reding)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KWwE
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This fixes a Tegra20 regression that we introduced during the v3.18
merge window"
* tag 'pci-v3.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: tegra: Use physical range for I/O mapping
Commit 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO
resources") changed how I/O resources are parsed from DT. Rather than
containing the physical address of the I/O region, the addresses will now
be in I/O address space.
On Tegra the union of all ranges is used to expose a top-level memory-
mapped resource for the PCI host bridge. This helps to make /proc/iomem
more readable.
Combining both of the above, the union would now include the I/O space
region. This causes a regression on Tegra20, where the physical base
address of the PCIe controller (and therefore of the union) is located at
physical address 0x80000000. Since I/O space starts at 0, the union will
now include all of system RAM which starts at 0x00000000.
This commit fixes this by keeping two copies of the I/O range: one that
represents the range in the CPU's physical address space, the other for the
range in the I/O address space. This allows the translation setup within
the driver to reuse the physical addresses. The code registering the I/O
region with the PCI core uses both ranges to establish the mapping.
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This can be set by quirks/drivers to be used by the architecture code
that assigns the MSI addresses.
We additionally add verification in the core MSI code that the values
assigned by the architecture do satisfy the limitation in order to fail
gracefully if they don't (ie. the arch hasn't been updated to deal with
that quirk yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
With the new stacked irq domains, it becomes pretty tempting to
allocate an MSI domain per PCI bus, which would remove the requirement
of either relying on arch-specific code, or a default PCI MSI domain.
By allowing the msi_controller structure to carry a pointer to an
irq_domain, we can easily use this in pci_msi_setup_msi_irqs. The
existing code can still be used as a fallback if the MSI driver does
not populate the domain field.
Tested on arm64 with the GICv3 ITS driver.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1416048553-29289-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provide mechanism to directly alloc/free MSI/MSIX interrupt from
irqdomain, which will be used to replace arch_setup_msi_irq()/
arch_setup_msi_irqs()/arch_teardown_msi_irq()/arch_teardown_msi_irqs().
To kill weak functions, this patch introduce a new weak function
arch_get_pci_msi_domain(), which is to retrieve the MSI irqdomain
for a PCI device. This weak function could be killed once we get
a common way to associate MSI domain with PCI device.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/1416061447-9472-10-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Enhance PCI MSI core to support hierarchy irqdomain, so the common
code can be shared across architectures.
[ tglx: Extracted and combined from several patches ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Required to support non PCI based MSI.
[ tglx: Extracted from Jiangs patch series ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The PCI/MSI irq chip callbacks mask/unmask_msi_irq have been renamed
to pci_msi_mask/unmask_irq to mark them PCI specific. Rename all usage
sites. The conversion helper functions are kept around to avoid
conflicts in next and will be removed after merging into mainline.
Coccinelle assisted conversion. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: x86@kernel.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yijing Wang <wangyijing@huawei.com>
mask/unmask_msi_irq and __mask_msi/msix_irq are PCI/MSI specific
functions and should be named accordingly. This is a preparatory patch
to support MSI on non PCI devices.
Rename mask/unmask_msi_irq to pci_msi_mask/unmask_irq and document the
functions. Provide conversion helpers.
Rename __mask_msi/msix_irq to __pci_msi/msix_desc_mask so its clear
that they operated on msi_desc. Fixup the only user outside of
pci/msi.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename __read_msi_msg() to __pci_read_msi_msg() and kill unused
read_msi_msg(). It's a preparation to separate generic MSI code from
PCI core.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is the repsonsibility of arch_setup_msi_irq()/arch_setup_msi_irqs()
to call irq_set_msi_desc() to associate IRQ descriptors and MSI
descriptors. Kill the redundant call of irq_set_msi_desc() for MSI-X
interrupts in the PCI MSI core.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Per Documentation/CodingStyle, don't use braces around single statements.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Resource management
- Support 64-bit bridge windows if we have 64-bit dma_addr_t (Yinghai Lu)
PCI device hotplug
- Apply _HPX Link Control settings to all devices with a link (Yinghai Lu)
Generic host bridge driver
- Add DT binding for "linux,pci-domain" property (Lucas Stach)
APM X-Gene
- Assign resources to bus before adding new devices (Duc Dang)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=smv9
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for an issue with 64-bit PCI bus addresses on 32-bit
PAE kernels, an APM X-Gene problem (it depended on a generic change we
removed before merging), a fix for my hotplug device configuration
changes, and a devicetree documentation update.
Resource management:
- Support 64-bit bridge windows if we have 64-bit dma_addr_t (Yinghai Lu)
PCI device hotplug:
- Apply _HPX Link Control settings to all devices with a link (Yinghai Lu)
Generic host bridge driver:
- Add DT binding for "linux,pci-domain" property (Lucas Stach)
APM X-Gene:
- Assign resources to bus before adding new devices (Duc Dang)"
* tag 'pci-v3.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Support 64-bit bridge windows if we have 64-bit dma_addr_t
PCI: Apply _HPX Link Control settings to all devices with a link
PCI: Add missing DT binding for "linux,pci-domain" property
PCI: xgene: Assign resources to bus before adding new devices
* pci/msi:
s390/MSI: Use __msi_mask_irq() instead of default_msi_mask_irq()
Revert "PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()"
PCI/MSI: Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask Bits
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use xilinx_pcie_msi_chip, not xilinx_pcie_msi_controller]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use struct rcar_msi.chip, not ctrl]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use dw_pcie_msi_chip, not dw_pcie_msi_controller]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use struct tegra_msi.chip, not ctrl]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_iov_resource_bar() always sets its 'pci_bar_type' parameter to
'pci_bar_unknown'. Drop the parameter and just use 'pci_bar_unknown'
directly in the callers.
No functional change intended.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Chris Wright <chrisw@sous-sol.org>
CC: Yu Zhao <yuzhao@google.com>
As a consequence of restoring the detection of invalid BARs, add a new
informational printk like the following when such occurrences are
encountered.
pci ssss:bb:dd.f: [Firmware Bug]: reg 0xXX: invalid BAR (can't size)
Reported-by: William Unruh <unruh@physics.ubc.ca>
Reported-by: Martin Lucina <martin@lucina.net>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <willy@linux.intel.com>
Aaron reported that a 32-bit x86 kernel with Physical Address Extension
(PAE) support complains about bridge prefetchable memory windows above 4GB:
pci_bus 0000:00: root bus resource [mem 0x380000000000-0x383fffffffff]
...
pci 0000:03:00.0: reg 0x10: [mem 0x383fffc00000-0x383fffdfffff 64bit pref]
pci 0000:03:00.0: reg 0x20: [mem 0x383fffe04000-0x383fffe07fff 64bit pref]
pci 0000:03:00.1: reg 0x10: [mem 0x383fffa00000-0x383fffbfffff 64bit pref]
pci 0000:03:00.1: reg 0x20: [mem 0x383fffe00000-0x383fffe03fff 64bit pref]
pci 0000:00:02.2: PCI bridge to [bus 03-04]
pci 0000:00:02.2: bridge window [io 0x1000-0x1fff]
pci 0000:00:02.2: bridge window [mem 0x91900000-0x91cfffff]
pci 0000:00:02.2: can't handle 64-bit address space for bridge
In this kernel, unsigned long is 32 bits and dma_addr_t is 64 bits.
Previously we used "unsigned long" to hold the bridge window address. But
this is a bus address, so we should use dma_addr_t instead.
Use dma_addr_t to hold the bridge window base and limit.
The question of whether the CPU can actually *address* the window is
separate and depends on what the physical address space of the CPU is and
whether the host bridge does any address translation.
[bhelgaas: fix "shift count > width of type", changelog, stable tag]
Fixes: d56dbf5bab ("PCI: Allocate 64-bit BARs above 4G when possible")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=88131
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
* pci/host-designware:
PCI: designware: Add a blank line after declarations
* pci/host-dra7xx:
PCI: dra7xx: Add __init annotation to dra7xx_add_pcie_port()
PCI: dra7xx: Rename add_pcie_port() to dra7xx_add_pcie_port()
* pci/host-exynos:
PCI: exynos: Remove unnecessary return statement
PCI: exynos: Add exynos prefix to add_pcie_port()/pcie_init()
* pci/host-generic:
PCI: generic: Convert to DT resource parsing API
PCI: generic: Allocate config space windows after limiting bus number range
* pci/host-imx6:
PCI: imx6: Use tabs for indentation
* pci/host-keystone:
PCI: keystone: Remove unnecessary OOM message
PCI: keystone: Make ks_dw_pcie_msi_domain_ops static
* pci/host-layerscape:
PCI: layerscape: Add Freescale Layerscape PCIe driver
* pci/host-mvebu:
PCI: mvebu: Add a blank line after declarations
* pci/host-rcar:
PCI: rcar: Make rcar_pci static
* pci/host-spear:
PCI: spear: Remove unnecessary OOM message
PCI: spear: Add __init annotation to spear13xx_add_pcie_port()
PCI: spear: Rename add_pcie_port(), pcie_init() to spear13xx_add_pcie_port(), etc.
* pci/host-tegra:
PCI: tegra: Add Kconfig help text
PCI: tegra: Do not build on 64-bit ARM
Previously we applied _HPX type 2 record Link Control register settings
only to bridges with a subordinate bus. But it's better to apply them to
all devices with a link because if the subordinate bus has not been
allocated yet, we won't apply settings to the device.
Use pcie_cap_has_lnkctl() to determine whether the device has a Link
Control register instead of looking at dev->subordinate.
[bhelgaas: changelog]
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a standard help text to the Kconfig entry for the Tegra PCIe host
controller driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
32-bit and 64-bit ARM use very different infrastructure to register a PCI
host bridge. The Tegra PCIe host controller driver currently only supports
the 32-bit ARM infrastructure, so prevent it from being built on 64-bit ARM
where it will break.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The site-specific OOM messages are unnecessary, because they duplicate the
MM subsystem generic OOM message. This patch fixes the following
checkpatch warning:
WARNING: Possible unnecessary 'out of memory' message
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch fixes the following checkpatch warning:
WARNING: Missing a blank line after declarations
[bhelgaas: drop mvebu_pcie_add_bus() change because it's going away anyway]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
This patch fixes the following checkpatch warning:
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch fixes the following checkpatch warning:
WARNING: void function return statements are not generally useful
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch fixes the following checkpatch error:
ERROR: code indent should use tabs where possible
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The site-specific OOM messages are unnecessary because they duplicate the
MM subsystem generic OOM message. This patch fixes the following
checkpatch warning:
WARNING: Possible unnecessary 'out of memory' message
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We have same warning message for FLR and AF FLR and users can't know which
type of resets the PCI device is taking when there are pending
transactions. Print different messages for FLR and AF FLR cases.
[bhelgaas: make code structure parallel, add "anyway" to suggest risk]
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The X-Gene PCIe driver assumes pci_scan_root_bus() assigns resources as
proposed in [1]. But we dropped patch [1] because it would break some
architectures, which means the X-Gene PCIe driver is currently broken.
Add calls to scan the bus, assign resources, and add devices in the X-Gene
driver to fix this.
[bhelgaas: changelog]
[1] http://lkml.kernel.org/r/1412000971-9242-11-git-send-email-Liviu.Dudau@arm.com
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add __init annotation to dra7xx_add_pcie_port(), because
dra7xx_add_pcie_port() is called only by dra7xx_pcie_probe() which is
marked __init. This patch fixes a section mismatch warning:
WARNING: drivers/pci/host/built-in.o(.text.unlikely+0xcc): Section mismatch in reference from the function dra7xx_add_pcie_port() to the function .init.text:dw_pcie_host_init()
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add __init annotation to spear13xx_add_pcie_port(), because
spear13xx_add_pcie_port() is called only by spear13xx_pcie_probe(), which
is marked __init. This fixes a section mismatch warning:
WARNING: drivers/pci/host/built-in.o(.text.unlikely+0x94): Section mismatch in reference from the function spear13xx_add_pcie_port() to the function .init.text:dw_pcie_host_init()
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The add_pcie_port() and pcie_init() functions are SPEAr13xx-specific. Add
spear13xx prefix to avoid collision in global name space.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The add_pcie_port() function is dra7xx-specific. Add dra7xx prefix to
avoid collision in global name space.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add pcibios_msi_controller() to get the msi_controller associated with a
PCI device. This is to allow arches to store the msi_controller in the
arch-specific PCI sysdata.
[bhelgaas: changelog, take pci_dev instead of pci_bus]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"msi_chip" isn't very descriptive, so rename it to "msi_controller". That
tells a little more about what it does and is already used in device tree
bindings.
No functional change.
[bhelgaas: changelog, change *only* the struct name so it's reviewable]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The problem fixed by 0e4ccb1505 ("PCI: Add x86_msi.msi_mask_irq() and
msix_mask_irq()") has been fixed in a simpler way by a previous commit
("PCI/MSI: Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask
Bits").
The msi_mask_irq() and msix_mask_irq() x86_msi_ops added by 0e4ccb1505
are no longer needed, so revert the commit.
default_msi_mask_irq() and default_msix_mask_irq() were added by
0e4ccb1505 and are still used by s390, so keep them for now.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: xen-devel@lists.xenproject.org
The functions pci_dev_put(), pci_pme_wakeup_bus(), and put_device() return
immediately if their argument is NULL. Thus the test before the call is
not needed.
Remove these unnecessary tests.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
__pci_read_base() disables decoding while sizing device BARs. We can't
print while decoding is disabled, which leads to some rather messy exit
logic.
Coalesce the sizing logic to minimize the time decoding is disabled. This
lets us print errors where they're detected.
The refactoring also takes advantage of the symmetry of obtaining the BAR's
extent (pci_size) and storing the result as the 'region' for both the
32-bit and 64-bit BARs, consolidating both cases.
No functional change intended.
[bhelgaas: move pci_size() up, per Thomas Petazzoni, Thierry Reding, Kevin Hilman]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <willy@linux.intel.com>
Commit 6ac665c63d ("PCI: rewrite PCI BAR reading code") masked off
low-order bits from 'l', but not from 'sz'. Both are passed to pci_size(),
which compares 'base == maxbase' to check for read-only BARs. The masking
of 'l' means that comparison will never be 'true', so the check for
read-only BARs no longer works.
Resolve this by also masking off the low-order bits of 'sz' before passing
it into pci_size() as 'maxbase'. With this change, pci_size() will once
again catch the problems that have been encountered to date:
- AGP aperture BAR of AMD-7xx host bridges: if the AGP window is
disabled, this BAR is read-only and read as 0x00000008 [1]
- BARs 0-4 of ALi IDE controllers can be non-zero and read-only [1]
- Intel Sandy Bridge - Thermal Management Controller [8086:0103];
BAR 0 returning 0xfed98004 [2]
- Intel Xeon E5 v3/Core i7 Power Control Unit [8086:2fc0];
Bar 0 returning 0x00001a [3]
Link: [1] https://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/drivers/pci/probe.c?id=1307ef6621991f1c4bc3cec1b5a4ebd6fd3d66b9 ("PCI: probing read-only BARs" (pre-git))
Link: [2] https://bugzilla.kernel.org/show_bug.cgi?id=43331
Link: [3] https://bugzilla.kernel.org/show_bug.cgi?id=85991
Reported-by: William Unruh <unruh@physics.ubc.ca>
Reported-by: Martin Lucina <martin@lucina.net>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <willy@linux.intel.com>
CC: stable@vger.kernel.org # v2.6.27+
Many sysfs *_show function use cpu{list,mask}_scnprintf to copy cpumap
to the buffer aligned to PAGE_SIZE, append '\n' and '\0' to return null
terminated buffer with newline.
This patch creates a new helper function cpumap_print_to_pagebuf in
cpumask.h using newly added bitmap_print_to_pagebuf and consolidates
most of those sysfs functions using the new helper function.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: x86@kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MSI-X vector Mask Bits are in MSI-X Tables in PCI memory space. Xen PV
guests can't write to those tables. MSI vector Mask Bits are in PCI
configuration space. Xen PV guests can write to config space, but those
writes are ignored.
Commit 0e4ccb1505 ("PCI: Add x86_msi.msi_mask_irq() and
msix_mask_irq()") added a way to override default_mask_msi_irqs() and
default_mask_msix_irqs() so they can be no-ops in Xen guests, but this is
more complicated than necessary.
Add "pci_msi_ignore_mask" in the core PCI MSI code. If set,
default_mask_msi_irqs() and default_mask_msix_irqs() return without doing
anything. This is less flexible, but much simpler.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: xen-devel@lists.xenproject.org
NUMA systems with ACPI normally describe the physical topology via _PXM
methods. But many BIOSes don't implement _PXM, which leaves the kernel
with no way to discover the device topology, which reduces performance
because we can't put memory and processes close to the device.
The NUMA node of a PCI device is already exported in the sysfs "numa_node"
file. Make that file writable so users can workaround the lack of _PXM
methods in the BIOS. For example:
echo 3 > /sys/devices/pci0000:ff/0000:03:1f.3/numa_node
sets the node for PCI device 0000:03:1f.3.
Writing the file emits a FW_BUG warning to encourage users to request
firmware updates. It also taints the kernel with TAINT_FIRMWARE_WORKAROUND
because overriding the node incorrectly can cause performance issues.
[bhelgaas: changelog, documentation text]
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Myron Stowe <mstowe@redhat.com>
CC: Alexander Ducyk <alexander.h.duyck@redhat.com>
CC: Jiang Liu <jiang.liu@linux.intel.com>
When pcifront_try_connect() finds no PCI roots, it falls back to calling
pcifront_scan_root() for 0000:00. If that fails, it used to switch to
XenbusStateConnected and return success (because xenbus_switch_state()
currently always succeeds).
If pcifront_scan_root() fails, leave the XenbusState unchanged and return
an error code.
Similarly, pcifront_attach_devices() falls back to calling
pcifront_rescan_root() for 0000:00. If that fails, it used to switch to
XenbusStateConnected and return an error code.
If pcifront_rescan_root() fails, leave the XenbusState unchanged and return
the error code.
[bhelgaas: changelog]
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In order to consolidate DT configuration for PCI host controllers in the
kernel, a new API, of_pci_get_host_bridge_resources(), was developed to
allow parsing and assigning IO/BUS/MEM resources from DT, removing
duplicated code present in the majority of PCI host driver implementations.
Convert the existing PCI generic host controller driver to the new API.
Most of the code parsing ranges and creating resources is now delegated to
the of_pci_get_host_bridge_resources() API.
The PCI host controller code filters the resulting resource list and maps
IO space by using the newly introduced pci_ioremap_iospace() API.
New code supports only one IO resource per generic host controller, which
should cater for all existing host controller configurations.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The number of config space windows allocated for the host bridge depends on
how many bus numbers are below the bridge. Instead of first allocating the
windows and then limiting the bus resource, this patch reshuffles the code
so that if any limitation is applied to the bus resource, it is taken into
account in the windows allocation.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The AMD Nolan (NL) SoC contains a DesignWare USB3 Dual-Role Device that can
be operated either as a USB Host or a USB Device. In the AMD NL platform,
this device ([1022:7912]) has a class code of PCI_CLASS_SERIAL_USB_XHCI
(0x0c0330), which means the xhci driver will claim it.
But the dwc3 driver is a more specific driver for this device, and we'd
prefer to use it instead of xhci. To prevent xhci from claiming the
device, change the class code to 0x0c03fe, which the PCI r3.0 spec defines
as "USB device (not host controller)". The dwc3 driver can then claim it
based on its Vendor and Device ID.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sysfs
- Fix "enable" filename change (Greg Kroah-Hartman)
PCI device hotplug
- Revert duplicate merge (Kamal Mostafa)
Freescale i.MX6
- Wait for clocks to stabilize after ref_en (Richard Zhu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Uj0Z
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These changes, intended for v3.18, fix:
Sysfs
- Fix "enable" filename change (Greg Kroah-Hartman)
An unintentional sysfs filename change in commit 5136b2da77
("PCI: convert bus code to use dev_groups"), which appeared in
v3.13, changed "enable" to "enabled", and this changes it back.
Old users of "enable" are currently broken and will be helped by
this change. Anything that started to use "enabled" after v3.13
will be broken by this change. If necessary, we can add a symlink
to make both work, but this patch doesn't do that.
PCI device hotplug
- Revert duplicate merge (Kamal Mostafa)
A mistaken duplicate merge that added a check twice. Nothing's
broken; this just removes the unnecessary code.
Freescale i.MX6
- Wait for clocks to stabilize after ref_en (Richard Zhu)
An i.MX6 clock problem that prevents mx6 nitrogen boards from booting"
* tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Rename sysfs 'enabled' file back to 'enable'
PCI: imx6: Wait for clocks to stabilize after ref_en
Revert duplicate "PCI: pciehp: Prevent NULL dereference during probe"
Back in commit 5136b2da77 ("PCI: convert bus code to use dev_groups"),
I misstyped the 'enable' sysfs filename as 'enabled', which broke the
userspace API. This patch fixes that issue by renaming the file back.
Fixes: 5136b2da77 ("PCI: convert bus code to use dev_groups")
Reported-by: Jeff Epler <jepler@unpythonic.net>
Tested-by: Jeff Epler <jepler@unpythonic.net> # on v3.14-rt
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # 3.13
For boards without a reset GPIO we skip the delay between enabling the
pcie_ref_clk and touching the RC registers for configuration. This hangs
the system if there isn't a proper delay to ensure the clocks are settled
in the DW PCIe core.
Also iMX6Q always needs an additional 10us delay to make sure the reset is
propagated through the core, as we don't have an explicitly controlled
reset input on this SoC.
This fixes a problem with 3fce0e882f ("PCI: imx6: Delay enabling
reference clock for SS until it stabilizes"): the kernel doesn't boot on
systems that don't pass the PCI GPIO reset in the DTB. This regression
affects mx6 nitrogen boards.
[bhelgaas: add regression info in changelog]
Fixes: 3fce0e882f ("PCI: imx6: Delay enabling reference clock for SS until it stabilizes")
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Richard Zhu <richard.zhu@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
This reverts bceee4a97e ("PCI: pciehp: Prevent NULL dereference during
probe") because it was accidentally applied twice:
62e4492c30 ("PCI: Prevent NULL dereference during pciehp probe")
bceee4a97e ("PCI: pciehp: Prevent NULL dereference during probe")
Revert the latter to dispose of the duplicated code block.
[bhelgaas: tidy changelog, drop stable tag]
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Andreas Noever <andreas.noever@gmail.com>
If the irqchip handling the PCIe PME interrupt is not able
to enable interrupt wakeup we should properly reflect this
in the PME suspend status.
This fixes a kernel warning on resume, where it would try
to disable the irq wakeup that failed to be activated while
suspending, for example:
WARNING: CPU: 0 PID: 609 at kernel/irq/manage.c:536 irq_set_irq_wake+0xc0/0xf8()
Unbalanced IRQ 384 wake disable
Fixes: 76cde7e495 (PCI / PM: Make PCIe PME interrupts wake up from suspend-to-idle)
Reported-and-tested-by: Richard Zhu <richard.zhu@freescale.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make rcar_pci static because it is used only in this file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Make ks_dw_pcie_msi_domain_ops static because it is used only in this file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar<ssantosh@kernel.org>
The add_pcie_port() and pcie_init() functions are Exynos-specific. Add
exynos prefix to avoid collision in global name space.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUNonmAAoJEFxbo/MsZsTRHAQH/inCjpCT+pkvTB0YAVfVvgMI
gUogT8G+iB2MuCNpMffGIt8TAVXwcVtnOLH9ABH3IBVehzgipIbIiVEM9YhjrYvU
1rgIKBpmZqSpjDHoIHpdHeCH67cVnRzA/PyoxZWLxPNmQ0t6bNf9yeAcCXK9PfUc
7EAblUDmPGSx9x/EUnOKNNaZSEiUJZHDBXbMBLllk1+5H1vfKnpFCRGMG0IrfI44
KVP2NX9Gfa05edMZYtH887FYyjFe2KNV6LJvE7+w7h2Dy0yIzf7y86t0l4n8gETb
plvEUJ/lu9RYzTiZY/RxgBFYVTV59EqT45brSUtoe2Jcp8GSwiHslTHdfyFBwSo=
=gw4d
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
* pm-genirq:
PM / genirq: Document rules related to system suspend and interrupts
PCI / PM: Make PCIe PME interrupts wake up from suspend-to-idle
x86 / PM: Set IRQCHIP_SKIP_SET_WAKE for IOAPIC IRQ chip objects
genirq: Simplify wakeup mechanism
genirq: Mark wakeup sources as armed on suspend
genirq: Create helper for flow handler entry check
genirq: Distangle edge handler entry
genirq: Avoid double loop on suspend
genirq: Move MASK_ON_SUSPEND handling into suspend_device_irqs()
genirq: Make use of pm misfeature accounting
genirq: Add sanity checks for PM options on shared interrupt lines
genirq: Move suspend/resume logic into irq/pm code
PM / sleep: Mechanism for aborting system suspends unconditionally
The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.
Replace the uses with standard structure definitions instead. This is
similar to pci and usb device registration.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
AMD has confirmed that peer-to-peer between two southbridge functions does
not occur.
Add a quirk to indicate that these functions are isolated even though they
don't have an ACS capability.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81841
Signed-off-by: Marti Raudsepp <marti@juffo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joel Schopp <joel.schopp@amd.com>
* pci/host-designware:
PCI: designware: Remove open-coded bitmap operations
PCI: designware: Setup and clear exactly one MSI at a time
Conflicts:
drivers/pci/host/pcie-designware.c
Add the AppliedMicro X-Gene SOC PCIe host controller driver. The X-Gene
PCIe controller supports up to 8 lanes and GEN3 speed. The X-Gene SOC
supports up to 5 PCIe ports.
[bhelgaas: folded in MAINTAINERS and bindings updates]
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com> (driver)
Replace them by using the standard kernel bitmap ops. No functional
change, but makes the code a lot cleaner.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
* pci/host-generic:
arm64: Add architectural support for PCI
PCI: Add pci_remap_iospace() to map bus I/O resources
of/pci: Add support for parsing PCI host bridge resources from DT
of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()
PCI: Add generic domain handling
of/pci: Fix the conversion of IO ranges into IO resources
of/pci: Move of_pci_range_to_resource() to of/address.c
ARM: Define PCI_IOBASE as the base of virtual PCI IO space
of/pci: Add pci_register_io_range() and pci_pio_to_address()
asm-generic/io.h: Fix ioport_map() for !CONFIG_GENERIC_IOMAP
Conflicts:
drivers/pci/host/pci-tegra.c
The only use of "status" is to hold a value which is immediately returned,
so just return and remove the variable directly.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
default_restore_msi_irq() already has the struct msi_desc pointer required
by __write_msi_msg(), so call it directly instead of having write_msi_msg()
look it up from the IRQ.
No functional change.
[bhelgaas: split into separate patch]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "msi_bus" sysfs file for bridges sets a bus flag to allow or disallow
future driver requests for MSI or MSI-X. Previously, the sysfs file
existed for endpoints but did nothing.
Add "msi_bus" support for endpoints, so an administrator can prevent the
use of MSI and MSI-X for individual devices.
Note that as for bridges, these changes only affect future driver requests
for MSI or MSI-X, so drivers may need to be reloaded.
Add documentation for the "msi_bus" sysfs file.
[bhelgaas: changelog, comments, add "subordinate", add endpoint printk,
rework bus_flags setting, make bus_flags printk unconditional]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"msi_attrib.pos" is only used for MSI (not MSI-X), and we already cache the
MSI capability offset in "dev->msi_cap".
Remove "pos" from the struct msi_attrib and use "dev->msi_cap" directly.
[bhelgaas: changelog, fix whitespace]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After commit 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not
kobjects"), the kobject in struct msi_desc is unused.
Remove the unused struct kobject from struct msi_desc.
[bhelgaas: changelog]
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename pci_msi_check_device() to pci_msi_supported() for clarity. Note
that pci_msi_supported() returns true if MSI/MSI-X is supported, so code
like:
if (pci_msi_supported(...))
reads naturally.
[bhelgaas: changelog, split to separate patch, reverse sense]
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Both callers of pci_msi_check_device() check that the device is in D0
state, so move the check from the callers into pci_msi_check_device()
itself.
In pci_enable_msi_range(), note that pci_msi_check_device() never returns a
positive value any more, so the loop that called it until it returns zero
or negative is no longer necessary.
[bhelgaas: changelog, split to separate patch]
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
No architectures implement arch_msi_check_device() or the struct msi_chip
.check_device() method, so remove them.
Remove the "type" parameter to pci_msi_check_device() because it was only
used to call arch_msi_check_device() and is no longer needed.
[bhelgaas: changelog, split to separate patch]
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_remap_iospace() to map bus I/O resources into the CPU virtual
address space. Architectures with special needs may provide their own
version, but most should be able to use this one.
This function is useful for PCI host bridge drivers that need to map the
PCI I/O resources into virtual memory space.
[bhelgaas: phys_addr description, drop temporary "err" variable]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
CC: Arnd Bergmann <arnd@arndb.de>
Add pci_get_new_domain_nr() to allocate a new domain number and
of_get_pci_domain_nr() to retrieve the PCI domain number of a given device
from DT. Host bridge drivers or architecture-specific code can choose to
implement their PCI domain number policy using these two functions.
Using of_get_pci_domain_nr() guarantees a stable PCI domain number on every
boot provided that all host bridge controllers are assigned a number in the
device tree using "linux,pci-domain" property. Mixing use of
pci_get_new_domain_nr() and of_get_pci_domain_nr() is not recommended as it
can lead to potentially conflicting domain numbers being assigned to root
buses behind different host bridges.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Catalin Marinas <catalin.marinas@arm.com>
The handling of PCI domains (or PCI segments in ACPI speak) is usually a
straightforward affair but its implementation is currently left to the
architectural code, with pci_domain_nr(b) querying the value of the domain
associated with bus b.
This patch introduces CONFIG_PCI_DOMAINS_GENERIC as an option that can be
selected if an architecture wants a simple implementation where the value
of the domain associated with a bus is stored in struct pci_bus.
The architectures that select CONFIG_PCI_DOMAINS_GENERIC will then have to
implement pci_bus_assign_domain_nr() as a way of setting the domain number
associated with a root bus. All child buses except the root bus will
inherit the domain_nr value from their parent.
Signed-off-by: Catalin Marinas <Catalin.Marinas@arm.com>
[Renamed pci_set_domain_nr() to pci_bus_assign_domain_nr()]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
The ranges property for a host bridge controller in DT describes the
mapping between the PCI bus address and the CPU physical address. The
resources framework however expects that the IO resources start at a pseudo
"port" address 0 (zero) and have a maximum size of IO_SPACE_LIMIT. The
conversion from PCI ranges to resources failed to take that into account,
returning a CPU physical address instead of a port number.
Also fix all the drivers that depend on the old behaviour by fetching the
CPU physical address based on the port number where it is being needed.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Catalin Marinas <catalin.marinas@arm.com>
The setup_irq function is supposed to set up exactly one MSI IRQ. Multiple
IRQ setup is handled differently, to respect the choices made by the upper
layers.
Also only clear one MSI IRQ at a time; the PCI core will call into this
function multiple times if it has to tear down more than one MSI IRQ.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
In 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to
64-bit resources"), we added IORESOURCE_MEM_64 to the mask in
pci_assign_unassigned_root_bus_resources(), but not to the mask in
pci_assign_unassigned_bridge_resources().
Add IORESOURCE_MEM_64 to the pci_assign_unassigned_bridge_resources() type
mask.
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
Intel has verified there is no peer-to-peer between functions for the below
selection of 82598, 82599, and X520 10G NICs. These NICs lack an ACS
capability, so we're not able to determine this isolation without the help
of quirks.
Generalize the Solarflare quirk and add these Intel 10G NICs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <John.ronciak@intel.com>
* pci/host-designware:
PCI: designware: Add get_msi_data() to pcie_host_ops
PCI: designware: Rename get_msi_data() to get_msi_addr()
PCI: designware: Fix IO resource end address calculation
PCI: designware: Fix configuration base address when using 'reg'
PCI: designware: Use NULL instead of false
[bhelgaas: Fixup keystone for "PCI: designware: Rename get_msi_data() to
get_msi_addr()"]
The patch exports 2 MSI message relevant functions, which will be
used by VFIO PCI driver. The VFIO PCI driver would be built as
a module.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add strings for all AER error bits defined in PCIe r3.0.
[bhelgaas: changelog, drop designated initializer change]
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/hotplug:
PCI: pciehp: Stop disabling notifications during init
PCI: pciehp: Add more Slot Control debug output
PCI: pciehp: Fix wait time in timeout message
* pci/initdata:
x86/PCI: Mark PCI BIOS initialization code as such
x86/PCI: Constify pci_mmcfg_probes[] array
x86/PCI: Mark constants of pci_mmcfg_nvidia_mcp55() as __initconst
x86/PCI: Move __init annotation to the correct place
x86/PCI: Mark DMI tables as initialization data
* pci/misc:
PCI: Move PCI_VENDOR_ID_VMWARE to pci_ids.h
Enumeration
- Revert "PCI: Don't scan random busses in pci_scan_bridge()" (Bjorn Helgaas)
- Revert "PCI: Make sure bus number resources stay within their parents bounds" (Bjorn Helgaas)
PCI device hotplug
- Fix pciehp pcie_wait_cmd() timeout (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qP+Z
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a few fixes that should be in v3.17.
- Reverting "Don't scan random busses" covers up a CardBus regression
having to do with allocating CardBus bus numbers.
- Reverting "Make sure bus numbers stay within parents bounds" covers
up an ACPI _CRS bug that makes us reconfigure a bridge, causing a
broken device behind it to stop responding.
- The pciehp timeout change fixes some code we added in v3.17.
Without the fix, we can send a new hotplug command too early,
before the timeout has expired.
I hope for better fixes for the reverts, but those will have to come
after v3.17"
* tag 'pci-v3.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: pciehp: Fix pcie_wait_cmd() timeout
Revert "PCI: Make sure bus number resources stay within their parents bounds"
Revert "PCI: Don't scan random busses in pci_scan_bridge()"
The modifications effectively change the value of len_tmp
in the case where the first condition is not met.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The following Coccinelle semantic patch was used to find and correct cases
of assignments in "if" conditions:
@@
expression var, expr;
statement S;
@@
+ var = expr;
if(
- (var = expr)
+ var
) S
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add space before open parenthesis as is conventional.
No functional change.
[bhelgaas: fix a few more in ibmphp, shpchp]
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a struct pcie_host_ops .get_msi_data() method for platforms to return
their special MSI message data.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
The struct pcie_host_ops .get_msi_data() method returns the MSI message
address. To accurately express its purpose, rename it to .get_msi_addr().
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
End address should be equal to start_addr + size - 1. Fix PCI IO resource
end address calculation.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
The code has calculated cfg0_base and cfg1_base when parsing 'reg' or
'ranges' property of PCI DTS node, so remove duplicate calculation. When
using 'reg', resource cfg is not used, so this code computed an incorrect
configuration base.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit KUMAR <mohit.kumar@st.com>
During pciehp initialization, we previously wrote two hotplug commands:
pciehp_probe
pcie_init
pcie_disable_notification
pcie_write_cmd # command 1
pcie_init_notification
pcie_enable_notification
pcie_write_cmd # command 2
For controllers with errata like Intel CF118, we previously waited for a
timeout before issuing the second hotplug command because the first command
only updates interrupt enable bits and is not a "real" hotplug command, so
the controller doesn't report Command Completed for it.
But there's no need to disable notifications in the first place. If BIOS
left them enabled, we could easily take an interrupt before disabling them,
so there's no benefit in disabling them for the tiny window before we
enable them.
Drop the unnecessary pcie_disable_notification() call.
[bhelgaas: changelog]
Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e7-v2-spec-update.html
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add more Slot Control debug output and move one print after
pcie_write_cmd() to be consistent with other debug output.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When we warned about a timeout on a hotplug command, we previously printed
the time between calls to pcie_write_cmd(), without accounting for any time
spent actually waiting. Consider this sequence:
pcie_write_cmd
write SLTCTL
cmd_started = jiffies # T1
pcie_write_cmd
pcie_wait_cmd
now = jiffies # T2
wait_event_timeout # we may wait here
if (timeout)
ctrl_info("Timeout on command issued %u msec ago",
jiffies_to_msecs(now - cmd_started))
We previously printed (T2 - T1), but that doesn't include the time spent in
wait_event_timeout().
Fix this by using the current jiffies value, not the one cached before
calling wait_event_timeout().
[bhelgaas: changelog, use current jiffies instead of adding timeout]
Fixes: 40b960831c ("PCI: pciehp: Compute timeout from hotplug command start time")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pcie_poll_cmd() take msecs instead of jiffies, so convert timeout to msecs.
Fixes: 40b960831c ("PCI: pciehp: Compute timeout from hotplug command start time")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Solarflare confirms that these devices do not allow peer-to-peer between
functions. Quirk them to allow IOMMU grouping to expose this isolation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Stonehouse <rstonehouse@solarflare.com>
of_get_address() expects pointers in the third and fourth parameters.
Pass NULL in order to fix the following sparse warnings:
drivers/pci/host/pcie-designware.c:433:51: warning: Using plain integer as NULL pointer
drivers/pci/host/pcie-designware.c:433:58: warning: Using plain integer as NULL pointer
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
pci_get_dma_source() is unused, so remove it. We now have
dma_alias_devfn() to describe this.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_find_upstream_pcie_bridge() is unused, so remove it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Geert Uytterhoeven reported a warning when building pci-mvebu:
drivers/pci/host/pci-mvebu.c: In function 'mvebu_get_tgt_attr':
drivers/pci/host/pci-mvebu.c:887:39: warning: 'rtype' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (slot == PCI_SLOT(devfn) && type == rtype) {
^
And indeed, the code of mvebu_get_tgt_attr() may lead to the usage of rtype
when being uninitialized, even though it would only happen if we had
entries other than I/O space and 32 bits memory space.
This commit fixes that by simply skipping the current DT range being
considered, if it doesn't match the resource type we're looking for.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.12+
PCIe configuration space should be passed through reg property, rather than
through ranges property. This patch does the correction for SPEAr13XX
SOCs.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.
The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D. Most interface types defined in the spec do not use
alpha characters, so they won't be affected. For example, 00h, 01h, 10h,
20h, etc. are unaffected.
Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.
[bhelgaas: changelog]
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: stable@vger.kernel.org
* pci/host-designware:
PCI: designware: Fold struct pcie_port_info into struct pcie_port
* pci/host-imx6:
PCI: imx6: Delay enabling reference clock for SS until it stabilizes
* pci/host-keystone:
PCI: keystone: Set device ID based on SoC to support multiple ports
PCI: keystone: Assume controller is already in RC mode
PCI: keystone: Limit MRSS for all downstream devices
* pci/host-tegra:
PCI: tegra: Add Tegra124 support
PCI: tegra: Make sure the PCIe PLL is really reset
PCI: tegra: Fix extended configuration space mapping
PCI: tegra: Clear CLKREQ# enable on port disable
* pci/host-xilinx:
PCI: xilinx: Fix xilinx_pcie_assign_msi() return value test
* pci/enumeration:
PCI: Enable CRS Software Visibility for root port if it is supported
PCI: Check only the Vendor ID to identify Configuration Request Retry
* pci/misc:
PCI: Parenthesize PCI_DEVID and PCI_VPD_LRDT_ID parameters
PCI: Increase IBM ipr SAS Crocodile BARs to at least system page size
PCI/AER: Make <linux/aer.h> standalone includable
* pci/virtualization:
PCI: Use device flag helper functions
xen/pciback: Use PCI device flag helper functions
KVM: Use PCI device flag helper functions
PCI: Add device flag helper functions
PCI: Assume all Mellanox devices have broken INTx masking
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xIYe
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These fix:
- Boot video device detection on dual-GPU Apple systems
- Hotplug fiascos on VGA switcheroo with radeon & nouveau drivers
- Boot hang on Freescale i.MX6 systems
- Excessive "no hotplug settings from platform" warnings
In particular:
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)"
* tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
vgaarb: Drop obsolete #ifndef
vgaarb: Don't default exclusively to first video device with mem+io
ACPIPHP / radeon / nouveau: Remove acpi_bus_no_hotplug()
PCI: Remove "no hotplug settings from platform" warning
PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device
PCI: imx6: Put LTSSM in "Detect" state before disabling it
MAINTAINERS: Add Lucas Stach as co-maintainer for i.MX6 PCI driver
This reverts commit 1820ffdccb ("PCI: Make sure bus number resources stay
within their parents bounds") because it breaks some systems with LSI Logic
FC949ES Fibre Channel Adapters, apparently by exposing a defect in those
adapters.
Dirk tested a Tyan VX50 (B4985) with this device that worked like this
prior to 1820ffdccb9b:
bus: [bus 00-7f] on node 0 link 1
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-07])
pci 0000:00:0e.0: PCI bridge to [bus 0a]
pci_bus 0000:0a: busn_res: can not insert [bus 0a] under [bus 00-07] (conflicts with (null) [bus 00-07])
pci 0000:0a:00.0: [1000:0646] type 00 class 0x0c0400 (FC adapter)
Note that the root bridge [bus 00-07] aperture is wrong; this is a BIOS
defect in the PCI0 _CRS method. But prior to 1820ffdccb, we didn't
enforce that aperture, and the FC adapter worked fine at 0a:00.0.
After 1820ffdccb, we notice that 00:0e.0's aperture is not contained in
the root bridge's aperture, so we reconfigure it so it *is* contained:
pci 0000:00:0e.0: bridge configuration invalid ([bus 0a-0a]), reconfiguring
pci 0000:00:0e.0: PCI bridge to [bus 06-07]
This effectively moves the FC device from 0a:00.0 to 07:00.0, which should
be legal. But when we enumerate bus 06, the FC device doesn't respond, so
we don't find anything. This is probably a defect in the FC device.
Possible fixes (due to Yinghai):
1) Add a quirk to fix the _CRS information based on what amd_bus.c read
from the hardware
2) Reset the FC device after we change its bus number
3) Revert 1820ffdccb
Fix 1 would be relatively easy, but it does sweep the LSI FC issue under
the rug. We might want to reconfigure bus numbers in the future for some
other reason, e.g., hotplug, and then we could trip over this again.
For that reason, I like fix 2, but we don't know whether it actually works,
and we don't have a patch for it yet.
This revert is fix 3, which also sweeps the LSI FC issue under the rug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84281
Reported-by: Dirk Gouders <dirk@gouders.net>
Tested-by: Dirk Gouders <dirk@gouders.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
CC: Yinghai Lu <yinghai@kernel.org>
This reverts commit fc1b253141 ("PCI: Don't scan random busses in
pci_scan_bridge()") because it breaks CardBus on some machines.
David tested a Dell Latitude D505 that worked like this prior to
fc1b253141b3:
pci 0000:00:1e.0: PCI bridge to [bus 01]
pci 0000:01:01.0: CardBus bridge to [bus 02-05]
Note that the 01:01.0 CardBus bridge has a bus number aperture of
[bus 02-05], but those buses are all outside the 00:1e.0 PCI bridge bus
number aperture, so accesses to buses 02-05 never reach CardBus. This is
later patched up by yenta_fixup_parent_bridge(), which changes the
subordinate bus number of the 00:1e.0 PCI bridge:
pci_bus 0000:01: Raising subordinate bus# of parent bus (#01) from #01 to #05
With fc1b253141, pci_scan_bridge() fails immediately when it notices that
we can't allocate a valid secondary bus number for the CardBus bridge, and
CardBus doesn't work at all:
pci 0000:01:01.0: can't allocate child bus 01 from [bus 01]
I'd prefer to fix this by integrating the yenta_fixup_parent_bridge() logic
into pci_scan_bridge() so we fix the bus number apertures up front. But
I don't think we can do that before v3.17, so I'm going to revert this to
avoid the problem while we're working on the long-term fix.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=83441
Link: http://lkml.kernel.org/r/1409303414-5196-1-git-send-email-david.henningsson@canonical.com
Reported-by: David Henningsson <david.henningsson@canonical.com>
Tested-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
* pci/vga:
vgaarb: Drop obsolete #ifndef
vgaarb: Don't default exclusively to first video device with mem+io
* commit '6a73336bde29':
PCI: Remove "no hotplug settings from platform" warning
We should be testing "hwirq" instead of "irq". "irq" is unsigned so it's
never less than zero. Also it's uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Srikanth Thokala <sthokal@xilinx.com>
The PCIe controller on Tegra124 has two root ports that can be used in a
x4/x1 or x2/x1 configuration and can run at PCIe 2.0 link speeds (up to
5 GT/s). The PHY programming has been moved into a separate controller, so
the driver now needs to request an external PHY referenced using the device
tree.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Depending on the prior state of the controller, the PLL reset may not be
pulsed. Clear the register bit and set it after a small delay to ensure
that the PLL is really reset.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Yuen <eyuen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The 16 chunks of 64 KiB that need to be stitched together to make up the
configuration space for one bus (1 MiB) are located 24 bits (== 16 MiB)
apart in physical address space. This is determined by the start of the
extended register field (bits 24-27) in the physical mapping.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Peter Daifuku <pdaifuku@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a root port is disabled, disable the CLKREQ# signal if available.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Crocodile chip occasionally comes up with 4k and 8k BAR sizes. Due to
an erratum, setting the SR-IOV page size causes the physical function BARs
to expand to the system page size. Since ppc64 uses 64k pages, when Linux
tries to assign the smaller resource sizes to the now 64k BARs the address
will be truncated and the BARs will overlap.
Force Linux to allocate the resource as a full page, which avoids the
overlap.
[bhelgaas: print expanded resource, too]
Signed-off-by: Douglas Lehr <dllehr@us.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Milton Miller <miltonm@us.ibm.com>
CC: stable@vger.kernel.org
Use PCI device flag helper functions when checking whether a device is
assigned. No functional change.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
K2E SoC has two PCI ports. The SATA controller is connected to second PCI
port (port 1). To support multiple port handling in Keystone PCI driver,
read the PCI device ID dynamically by iomap/read/unmap during probe and
save it in driver's private data and update it in host init code. The PCI
device ID field in the RC's config space is not filled by default by the
hardware and has to be updated by the PCI driver by reading the same from
the SoC register indicated by reg index #2 in DT bindings.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Keystone PCI hardware supports both RC and EP modes and devcfg register has
bits to boot strap the device to either of these modes. It seems proper to
add this functionality to the boot loader rather than in the driver as
device will be operating in either mode, not both any time. Currently the
driver supports only RC mode and hence register configuration in the driver
is not needed and the driver can assume the hardware is in RC mode.
Also update the DT documentation accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Keystone PCIe controller has a limitation that memory read request size
must not exceed 256 bytes. This is a hardware limitation. Add a quirk to
force this limit on all downstream devices by updating MRRS.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>