Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000, e1000e, ixgbe and i40evf.
Emil provides a fix for ixgbe so that non-fiber devices with MNG FW enabled
are able to link at 100Mbps.
Jacob provides several changes for ixgbe, most of which are PTP related.
Renames ixgbe_ptp_enable() to ixgbe_ptp_feature_enable() to better reflect
the functions purpose. Extracts the hardware setup logic for the PTP
hardware bits from the ixgbe_ptp_set_ts_config() to enable future work for
the ixgbe_ptp_reset(). Maintain the hwstamp configuration through a reset
and extracts the creation of the PTP clock device from ptp_init() in order
to properly handle a suspend/resume cycle and only calls it if we don't
already have a ptp_clock pointer.
David provides a patch to expend the e1000e driver to turn on unicast
PROMISC when there is failure to write to a shared receive address register.
The fix update_phy_task() for 82579 is expanded to include newer PHYs as well
so that the dev_spec->eee_lp_ability has the correct value when going into
SX states.
Todd provides a e1000e fix an errata for 82574/82583 where it is possible
bad bits are read from SYSTIMH/L so check to see that the time is
incrementing at a reasonable rate and is a multiple of the time incremental
value. Removes a redundant igb PHY power down register write.
Andi Kleen out of lines two write functions for e1000e to save 30k text size.
Tobias Klauser converts the e1000 and i40evf drivers to use the
is_broadcast_ether_addr() and is_multicast_ether_addr().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark new interfaces as idle to allow operations that require that
interfaces are idle to take place. Interface types that are always
not idle (like AP interfaces) will be set as not idle when they are
assigned a channel context.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach<emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During strong signal fluctuations under high throughput, few consecutive
failed A-MPDU transmissions can easily trigger packet loss notification,
and thus (in AP mode) client disconnection.
Reduce the number of false positives by checking the A-MPDU status flag
and treating a failed A-MPDU as a single packet.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing so will lead to an oops for a p2p-dev interface, since it has
no netdev.
Cc: stable@vger.kernel.org
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the rate control algorithm uses a selection table, it
is leaked when the station is destroyed - fix that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Christophe Prévotaux <cprevotaux@nltinc.com>
Fixes: 0d528d85c5 ("mac80211: improve the rate control API")
Cc: stable@vger.kernel.org # v3.10+
[add commit log entry, remove pointless NULL check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generalize the power conversion from mW to dBm
using log. This should fix the below compilation
error for country NO which adds a new power value
2000mW which is not handled earlier.
CC [M] net/wireless/wext-sme.o
CC [M] net/wireless/regdb.o
net/wireless/regdb.c:1130:1: error: Unknown undeclared here (not in
a function)
net/wireless/regdb.c:1130:9: error: expected } before power
make[2]: *** [net/wireless/regdb.o] Error 1
make[1]: *** [net/wireless] Error 2
make: *** [net] Error 2
Reported-By: John Walker <john@x109.net>
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
[remove unneeded parentheses, fix rounding by using %.0f]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This prevents leaving incomplete scatter-gather
transfer on CE rings which can lead firmware to
crash.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to read invalid state of CE ring
buffer indexes. This could lead to scatter-gather
transfer failure in mid-way and crash firmware
later by leaving garbage data on the ring.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It seems ath10k firmware gives us no way to know
the rssi for rx-fragments.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW creates self-peer for AP internally.
This prevents ath10k from trying to create
explicit self-peer during hw recovery and thus
prevents a timeout and a warning during teardown:
ath10k: removing stale peer $AP_BSSID from vdev_id 0
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All configuration sequences should be protected
with conf_mutex to avoid concurrent/conflicting
requests.
This should make sure that wep tx key setup is not
performed while hw is restarted (at least).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes sure no further tx requests are
submitted to HTT before driver teardown.
This should prevent invalid pointer/NULL
dereference on htt tx pool in ath10k_htt_tx() in
some cases of heavy traffic.
kvalo: remove the WARN_ON() if conf_mutex is held
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reduces risk of races and prepares for more
hw restart fixes.
It also makes sense to perform teardown after
mac80211 starts its restart routine as it
guarantees it has stopped itself by then
(including tx queues).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes failpath when override AC pdev param
setup fails and makes other pdev params setting
fail as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the is_multicast_ether_addr helper function from linux/etherdevice.h
instead of open coding the multicast address check.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the is_broadcast_ether_addr/is_multicast_ether_addr helper functions
from linux/etherdevice.h instead of open coding them.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the registers used to power down the PHY was found to be wrong
(should be bit 2 not bit 1) on further inspection it was also found to
be redundant.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Out of lining these two common inlines saves about 30k text size,
due to their errata workarounds.
14131431 2008136 1507328 17646895 10d452f vmlinux-before-e1000e
14101415 2004040 1507328 17612783 10cbfef vmlinux-e1000e
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the update_phy_task was only calling e1000_set_eee_pchlan()
for phy.type 82579. This patch is to cause this function to be called
for 82579 and newer phy.types. This causes the dev_spec->eee_lp_ability
to have the correct value when going into SX states.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to a synchronization error, the value read from SYSTIML/SYSTIMH
might be incorrect.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without this fix, freshly rebooted Linux creates a new IBSS
instead of joining an existing one. Only when jiffies counter
overflows after 5 minutes the IBSS can be successfully joined.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
[edit commit message slightly]
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the check to turn on promiscuous mode only took into account
the total number of SHared Receive Address (SHRA) registers and if the
request was for a register within that range. It is possible that the
Management Engine might have locked a number of SHRA and not allowed a
new address to be written to the requested register.
Add a function to determine the number of unlocked SHRA registers. Then
determine if the number of registers available is sufficient for our needs,
if not then return -ENOMEM so that UNICAST PROMISC mode is activated.
Since the method by which ME claims SHRA registers is non-deterministic,
also add a return value to the function attempting to write an address
to a SHRA, and return a -E1000_ERR_CONFIG if the write fails. The error
will be passed up the function chain and allow the driver to also set
UNICAST PROMISC when this happens.
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resume path calls .open but suspend path cannot call .stop because
fdirs should not be freed and control over hardware should not be
released until WoL is configured. To avoid having to duplicate all
changes made in .stop on suspend path split out part of .stop that
is relevant during suspend and call it from .stop and during suspend.
This fix also ensures that ixgbe_ptp_suspend is called during the
suspend path, and helps avoid similar errors. We can't call
ixgbe_ptp_stop, since it will free the PTP clock device, which we
shouldn't be doing during a suspend path.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we are adding proper support for suspend of PTP, extract out of
ixgbe_ptp_stop those things relevant to suspend. Then, have
ixgbe_ptp_stop call ixgbe_ptp_suspend. The next patch in the series will
have ixgbe_ptp_suspend called from the ixgbe_suspend path.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to properly handle a suspend/resume cycle, we cannot destroy
the PTP clock device. As part of this, we should only re-create the
device on first initialization. After a resume, when ixgbe_ptp_init is
called, we won't create a new clock, and we will use the old clock
device. To that end, this patch extracts the clock creation out of
ptp_init, and only calls it if we don't already have a ptp_clock
pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather than clearing the hwtstamp configuration, we should use the known
configuration requested by the user and call the function which has now
been separated from the ioctl. This means that after a reset, the
timestamp mode will be maintained rather than lost. We still can't
maintain the clock value, however.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently all of the hardware setup logic for the PTP hardware bits is
buried inside of the ioctl which sets the timestamp configuration. This
makes it hard to use this logic in other places (primarily reset), and
this means we can't restore current timestamp mode upon a MAC reset.
Extracting this logic into a separate function will enable future work
for the ixgbe_ptp_reset function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the name ixgbe_ptp_enable could be misconstrued as a function
which enables the whole PTP core, rename this function so that it is
clear the function is for enabling of the extra features such as PPS
signal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver was calling setup_link to make sure that fiber interfaces with MNG FW
enabled will get link on probe because the laser was most likely turned off.
This prevented non-fiber devices with MNG FW from linking at 100Mbps.
This patch adds a check to only call setup_link for fiber devices.
Reported-and-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We're currently sending NEW_WIPHY events for renames (which
is a bit odd, but now can't be changed), but also send them
for really new devices that register.
Also send DEL_WIPHY events when a device is removed, the
event ID for this was already reserved.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If ath10k was built into the kernel it could stall
booting for 120 seconds by default (60 seconds for
each firmware API variant) waiting for firmware
files before userspace was ready or filesystems
mounted.
Fix this by making the core registering
asynchronous.
This also shoves off about 1 second from boot time
on most systems since the driver is now mostly
initialized in a worker and modprobe takes very
little time to complete.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The tasklet is already guaranteed to be killed on
the teardown path.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will avoid unnecessary forward declaration of
any kind in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents protected flag being stripped from
undecrypted raw sniffed frames when monitor
interface is active.
Reported-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Tested-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the commit below, cfg80211_chandef_dfs_required()
will warn if it gets a an NL80211_IFTYPE_UNSPECIFIED iftype
as explicitely written in the commit log.
When an virtual monitor interface is added, its type is set
in ieee80211_sub_if_data.vif.type, but not in
ieee80211_sub_if_data.wdev.iftype which is passed to
cfg80211_chandef_dfs_required() hence resulting in the
following warning:
WARNING: CPU: 1 PID: 21265 at net/wireless/chan.c:376 cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]()
Modules linked in: [...]
CPU: 1 PID: 21265 Comm: ifconfig Tainted: G W O 3.13.11+ #12
Hardware name: Dell Inc. Latitude E6410/0667CC, BIOS A01 03/05/2010
0000000000000009 ffff88008f5fdb08 ffffffff817d4219 ffff88008f5fdb50
ffff88008f5fdb40 ffffffff8106f57d 0000000000000000 0000000000000000
ffff880081062fb8 ffff8800810604e0 0000000000000001 ffff88008f5fdba0
Call Trace:
[<ffffffff817d4219>] dump_stack+0x4d/0x66
[<ffffffff8106f57d>] warn_slowpath_common+0x7d/0xa0
[<ffffffff8106f5ec>] warn_slowpath_fmt+0x4c/0x50
[<ffffffffa04ea4ec>] cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]
[<ffffffffa06b1024>] ieee80211_vif_use_channel+0x94/0x500 [mac80211]
[<ffffffffa0684e6b>] ieee80211_add_virtual_monitor+0x1ab/0x5c0 [mac80211]
[<ffffffffa0686ae5>] ieee80211_do_open+0xe75/0x1580 [mac80211]
[<ffffffffa0687259>] ieee80211_open+0x69/0x70 [mac80211]
[snip]
Fixes: 00ec75fc5a ("cfg80211: pass the actual iftype when calling cfg80211_chandef_dfs_required()")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, when the driver is already using all the channel
contexts it can handle at once, we have to do an in-place switch
(ie. we cannot afford using an extra context temporarily for the
transaction). But some drivers may not support switching the channel
context assigned to a vif on the fly (ie. without unassigning and
assigning it) while others may only work if the context is changed on
the fly, without unassigning it first.
To allow these different scenarios, add a new driver operation that
let's the driver decide how to handle an in-place switch.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds xilinx CAN controller support. This driver supports both ZYNQ
CANPS and Soft IP AXI CAN controller.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Florian Fainelli says:
====================
net: sysfs: documentation updates
This patch set contains some updates to the sysfs Documentation for the
sysfs net class.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the network device statistics counter that are exposed as sysfs
attributes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs documentation for the various attributes of a network
interface exposed in /sys/class/<iface>/queues/{rx,tx}-<queue>/
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation for the phys_port_id sysfs attribute of a network
device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before f5efc69 ("netfilter: nf_tables: Add meta expression key for
bridge interface name"), the entire net/bridge/netfilter/ directory
depended on BRIDGE_NF_EBTABLES, ie. on ebtables. However, that
directory already contained the nf_tables bridge extension that
we should allow to compile separately. In f5efc69, we tried to
generalize this by using CONFIG_BRIDGE_NETFILTER which was not a good
idea since this option already existed and it is dedicated to enable
the Netfilter bridge IP/ARP filtering.
Let's try to fix this mess by:
1) making net/bridge/netfilter/ dependent on the toplevel
CONFIG_NETFILTER option, just like we do with the net/netfilter and
net/ipv{4,6}/netfilter/ directories.
2) Changing 'selects' to 'depends on' NETFILTER_XTABLES for
BRIDGE_NF_EBTABLES. I believe this problem was already before
f5efc69:
warning: (BRIDGE_NF_EBTABLES) selects NETFILTER_XTABLES which has
unmet direct dependencies (NET && INET && NETFILTER)
3) Fix ebtables/nf_tables bridge dependencies by making NF_TABLES_BRIDGE
and BRIDGE_NF_EBTABLES dependent on BRIDGE and NETFILTER:
warning: (NF_TABLES_BRIDGE && BRIDGE_NF_EBTABLES) selects
BRIDGE_NETFILTER which has unmet direct dependencies (NET && BRIDGE &&
NETFILTER && INET && NETFILTER_ADVANCED)
net/built-in.o: In function `br_parse_ip_options':
br_netfilter.c:(.text+0x4a5ba): undefined reference to `ip_options_compile'
br_netfilter.c:(.text+0x4a5ed): undefined reference to `ip_options_rcv_srr'
net/built-in.o: In function `br_nf_pre_routing_finish':
br_netfilter.c:(.text+0x4a8a4): undefined reference to `ip_route_input_noref'
br_netfilter.c:(.text+0x4a987): undefined reference to `ip_route_output_flow'
make: *** [vmlinux] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de906af1 (net: phy: make of_set_phy_supported work with genphy driver)
removed the last user of variable 'max_speed' in function
of_mdiobus_register_phy(), leading to compile warning "unused variable
‘max_speed’ [-Wunused-variable]". Thus remove it.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Felica protocol and Type 3 tags.
Both 212 and 424 kbps are supported.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
David S. Miller