This was shown up by running with "allmodconfig". I used
EXPORT_SYMBOL() to match existing conventions in files that
were already exporting symbols, or that were exported that way
by other architectures, and otherwise EXPORT_SYMBOL_GPL().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Change handle_swbp() to set regs->ip = bp_vaddr in advance, this is
what consumer->handler() needs but uprobe_get_swbp_addr() is not
exported.
This also simplifies the code and makes it more consistent across
the supported architectures. handle_swbp() becomes the only caller
of uprobe_get_swbp_addr().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
__skip_sstep() doesn't update regs->ip. Currently this is correct
but only "by accident" and it doesn't skip the whole insn. Change
it to advance ->ip by the length of the detected 0x66*0x90 sequence.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
We have received multiple reports of mmap failures when running with a
2:2 vm split. These manifest as either -EINVAL with a non page-aligned
address (ending 0xaaa) or a SEGV, depending on the application. The
issue is commonly observed in children of make, which appears to use
bottom-up mmap (assumedly because it changes the stack rlimit).
Further investigation reveals that this regression was triggered by
394ef6403a ("mm: use vm_unmapped_area() on arm architecture"), whereby
TASK_UNMAPPED_BASE is no longer page-aligned for bottom-up mmap, causing
get_unmapped_area to choke on misaligned addressed.
This patch fixes the problem by defining TASK_UNMAPPED_BASE in terms of
TASK_SIZE and explicitly aligns the result to 16M, matching the other
end of the heap.
Acked-by: Nicolas Pitre <nico@linaro.org>
Reported-by: Steve Capper <steve.capper@arm.com>
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Reported-by: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Realview fails to boot with this warning:
BUG: spinlock lockup suspected on CPU#0, init/1
lock: 0xcf8bde10, .magic: dead4ead, .owner: init/1, .owner_cpu: 0
Backtrace:
[<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:cf8bde10 r5:cf83d1c0 r4:cf8bde10 r3:cf83d1c0
[<c03294d0>] (dump_stack+0x0/0x1c) from [<c018926c>] (spin_dump+0x84/0x98)
[<c01891e8>] (spin_dump+0x0/0x98) from [<c0189460>] (do_raw_spin_lock+0x100/0x198)
[<c0189360>] (do_raw_spin_lock+0x0/0x198) from [<c032cbac>] (_raw_spin_lock+0x3c/0x44)
[<c032cb70>] (_raw_spin_lock+0x0/0x44) from [<c01c9224>] (pl011_console_write+0xe8/0x11c)
[<c01c913c>] (pl011_console_write+0x0/0x11c) from [<c002aea8>] (call_console_drivers.clone.7+0xdc/0x104)
[<c002adcc>] (call_console_drivers.clone.7+0x0/0x104) from [<c002b320>] (console_unlock+0x2e8/0x454)
[<c002b038>] (console_unlock+0x0/0x454) from [<c002b8b4>] (vprintk_emit+0x2d8/0x594)
[<c002b5dc>] (vprintk_emit+0x0/0x594) from [<c0329718>] (printk+0x3c/0x44)
[<c03296dc>] (printk+0x0/0x44) from [<c002929c>] (warn_slowpath_common+0x28/0x6c)
[<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c)
[<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c0070ab0>] (lockdep_trace_alloc+0xd8/0xf0)
[<c00709d8>] (lockdep_trace_alloc+0x0/0xf0) from [<c00c0850>] (kmem_cache_alloc+0x24/0x11c)
[<c00c082c>] (kmem_cache_alloc+0x0/0x11c) from [<c00bb044>] (__get_vm_area_node.clone.24+0x7c/0x16c)
[<c00bafc8>] (__get_vm_area_node.clone.24+0x0/0x16c) from [<c00bb7b8>] (get_vm_area_caller+0x48/0x54)
[<c00bb770>] (get_vm_area_caller+0x0/0x54) from [<c0020064>] (__alloc_remap_buffer.clone.15+0x38/0xb8)
[<c002002c>] (__alloc_remap_buffer.clone.15+0x0/0xb8) from [<c0020244>] (__dma_alloc+0x160/0x2c8)
[<c00200e4>] (__dma_alloc+0x0/0x2c8) from [<c00204d8>] (arm_dma_alloc+0x88/0xa0)[<c0020450>] (arm_dma_alloc+0x0/0xa0) from [<c00beb00>] (dma_pool_alloc+0xcc/0x1a8)
[<c00bea34>] (dma_pool_alloc+0x0/0x1a8) from [<c01a9d14>] (pl08x_fill_llis_for_desc+0x28/0x568)
[<c01a9cec>] (pl08x_fill_llis_for_desc+0x0/0x568) from [<c01aab8c>] (pl08x_prep_slave_sg+0x258/0x3b0)
[<c01aa934>] (pl08x_prep_slave_sg+0x0/0x3b0) from [<c01c9f74>] (pl011_dma_tx_refill+0x140/0x288)
[<c01c9e34>] (pl011_dma_tx_refill+0x0/0x288) from [<c01ca748>] (pl011_start_tx+0xe4/0x120)
[<c01ca664>] (pl011_start_tx+0x0/0x120) from [<c01c54a4>] (__uart_start+0x48/0x4c)
[<c01c545c>] (__uart_start+0x0/0x4c) from [<c01c632c>] (uart_start+0x2c/0x3c)
[<c01c6300>] (uart_start+0x0/0x3c) from [<c01c795c>] (uart_write+0xcc/0xf4)
[<c01c7890>] (uart_write+0x0/0xf4) from [<c01b0384>] (n_tty_write+0x1c0/0x3e4)
[<c01b01c4>] (n_tty_write+0x0/0x3e4) from [<c01acfe8>] (tty_write+0x144/0x240)
[<c01acea4>] (tty_write+0x0/0x240) from [<c01ad17c>] (redirected_tty_write+0x98/0xac)
[<c01ad0e4>] (redirected_tty_write+0x0/0xac) from [<c00c371c>] (vfs_write+0xbc/0x150)
[<c00c3660>] (vfs_write+0x0/0x150) from [<c00c39c0>] (sys_write+0x4c/0x78)
[<c00c3974>] (sys_write+0x0/0x78) from [<c0014460>] (ret_fast_syscall+0x0/0x3c)
This happens because the DMA allocation code is not respecting atomic
allocations correctly.
GFP flags should not be tested for GFP_ATOMIC to determine if an
atomic allocation is being requested. GFP_ATOMIC is not a flag but
a value. The GFP bitmask flags are all prefixed with __GFP_.
The rest of the kernel tests for __GFP_WAIT not being set to indicate
an atomic allocation. We need to do the same.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Realview EB with a rev B MPcore tile results in lots of warnings at
boot because it can't allocate enough IRQs. Fix this by increasing
the number of available IRQs.
WARNING: at /home/rmk/git/linux-rmk/arch/arm/common/gic.c:757 gic_init_bases+0x12c/0x2ec()
Cannot allocate irq_descs @ IRQ96, assuming pre-allocated
Modules linked in:
Backtrace:
[<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000002f5 r5:c042c62c r4:c044ff40 r3:c045f240
[<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c)
[<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029384>] (warn_slowpath_fmt+0x38/0x40)
[<c002934c>] (warn_slowpath_fmt+0x0/0x40) from [<c042c62c>] (gic_init_bases+0x12c/0x2ec)
[<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8)
[<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24)
[<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300)
[<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070)
---[ end trace 1b75b31a2719ed1c ]---
------------[ cut here ]------------
WARNING: at /home/rmk/git/linux-rmk/kernel/irq/irqdomain.c:234 irq_domain_add_legacy+0x80/0x140()
Modules linked in:
Backtrace:
[<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000000ea r5:c0081a38 r4:00000000 r3:c045f240
[<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c)
[<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c)
[<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c0081a38>] (irq_domain_add_legacy+0x80/0x140)
[<c00819b8>] (irq_domain_add_legacy+0x0/0x140) from [<c042c64c>] (gic_init_bases+0x14c/0x2ec)
[<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8)
[<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24)
[<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300)
[<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070)
---[ end trace 1b75b31a2719ed1d ]---
------------[ cut here ]------------
WARNING: at /home/rmk/git/linux-rmk/arch/arm/common/gic.c:762 gic_init_bases+0x170/0x2ec()
Modules linked in:
Backtrace:
[<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000002fa r5:c042c670 r4:00000000 r3:c045f240
[<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c)
[<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c)
[<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c042c670>] (gic_init_bases+0x170/0x2ec)
[<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8)
[<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24)
[<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300)
[<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070)
---[ end trace 1b75b31a2719ed1e ]---
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Punit Agrawal reports:
> I was trying to boot 3.8-rc5 on Realview EB 11MPCore using
> realview-smp_defconfig as a starting point but the kernel failed to
> progress past the log below (config attached).
>
> Pawel suggested I try reverting 384a290283 - "ARM: gic: use a private
> mapping for CPU target interfaces" that you've authored. With this
> commit reverted the kernel boots.
>
> I am not quite sure why the commit breaks 11MPCore but Pawel (cc'd)
> might be able to shed light on that.
Some early GIC implementations return zero for the first distributor
CPU routing register. This means we can't rely on that telling us
which CPU interface we're connected to. We know that these platforms
implement PPIs for IRQs 29-31 - but we shouldn't assume that these
will always be populated.
So, instead, scan for a non-zero CPU routing register in the first
32 IRQs and use that as our CPU mask.
Reported-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Exynos Kconfig fixup
- SIRF DT translation bug
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=e21G
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.8-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull late pinctrl fixes from Linus Walleij:
"Two patches appeared as of late, one was completely news to me, the
other one was rotated in -next for the next merge window but turned
out to be a showstopper.
- Exynos Kconfig fixup
- SIRF DT translation bug"
* tag 'pinctrl-for-v3.8-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sirf: replace of_gpio_simple_xlate by sirf specific of_xlate
pinctrl: exynos: change PINCTRL_EXYNOS option
Without this patch, it is trivial to determine kernel page
mappings by examining the error code reported to dmesg[1].
Instead, declare the entire kernel memory space as a violation
of a present page.
Additionally, since show_unhandled_signals is enabled by
default, switch branch hinting to the more realistic
expectation, and unobfuscate the setting of the PF_PROT bit to
improve readability.
[1] http://vulnfactory.org/blog/2013/02/06/a-linux-memory-trick/
Reported-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20130207174413.GA12485@www.outflux.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Similar to config_base and event_base, allow architecture
specific RDPMC ECX values.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Acked-by: Stephane Eranian <eranian@google.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1360171589-6381-6-git-send-email-jacob.shin@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move counter index to MSR address offset calculation to
architecture specific files. This prepares the way for
perf_event_amd to enable counter addresses that are not
contiguous -- for example AMD Family 15h processors have 6 core
performance counters starting at 0xc0010200 and 4 northbridge
performance counters starting at 0xc0010240.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Stephane Eranian <eranian@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1360171589-6381-5-git-send-email-jacob.shin@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Update these AMD bit field names to be consistent with naming
convention followed by the rest of the file.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Acked-by: Stephane Eranian <eranian@google.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1360171589-6381-4-git-send-email-jacob.shin@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Generalize northbridge constraints code for family 10h so that
later we can reuse the same code path with other AMD processor
families that have the same northbridge event constraints.
Signed-off-by: Robert Richter <rric@kernel.org>
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Stephane Eranian <eranian@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1360171589-6381-3-git-send-email-jacob.shin@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As of commit fea82210 ("m68k: switch to saner kernel_execve() semantics")
the non-mmu m68k targets have trapped on booting. The execing of /bin/init
causes the exec path to try and return through a 0x0 return address - thus
trapping or otherwise hanging or crashing.
The problem isn't in the exec path as such though, but rather in the
m68knommu start_thread() macro. It is trying to clear the a6 register that
it assumes is part of a struct switch_stack below the thread registers on
our stack. But that is not what the stack frames look like when this is run.
So it ends up corrupting our call stack and zeroing out a function return
address that is sitting there.
The clearing of a6 was introduced many years ago in commit 7bf9a37d8d
("m68knommu: force stack alignment on ColdFire"). It used to work because
the kernel init exec code path had a short cut back to the exception return
code, and it didn't need to return through the calls on the stack.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Pull DMA mapping fixes from Marek Szyprowski:
"This pull request contains important bugfix patches for 9
architectures, which finally fixes broken allmodconfig builds
introduced in v3.8-rc1. Those architectures don't use dma_map_ops
based implementation and require manual update or additional dummy
implementations of the missing new dma-mapping api functions:
dma_mmap_coherent and dma_get_sgtable."
* 'fixes-for-v3.8-rc7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
xtensa: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
parisc: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
mn10300: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
m68k: Provide dma_mmap_coherent() and dma_get_sgtable()
frv: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
cris: Provide dma_mmap_coherent() and dma_get_sgtable()
c6x: Provide dummy dma_mmap_coherent() and dma_get_sgtable()
blackfin: Provide dma_mmap_coherent() and dma_get_sgtable()
avr32: Provide dma_mmap_coherent() and dma_get_sgtable()
Since pinctrl-exynos can support exynos4 and exynos5 so changed
the option name to PINCTRL_EXYNOS for more clarity.
Cc: Thomas Abraham <Thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Typical cputime stats infrastructure relies on the timer tick and
its periodic polling on the CPU to account the amount of time
spent by the CPUs and the tasks per high level domains such as
userspace, kernelspace, guest, ...
Now we are preparing to implement full dynticks capability on
Linux for Real Time and HPC users who want full CPU isolation.
This feature requires a cputime accounting that doesn't depend
on the timer tick.
To implement it, this new cputime infrastructure plugs into
kernel/user/guest boundaries to take snapshots of cputime and
flush these to the stats when needed. This performs pretty
much like CONFIG_VIRT_CPU_ACCOUNTING except that context location
and cputime snaphots are synchronized between write and read
side such that the latter can safely retrieve the pending tickless
cputime of a task and add it to its latest cputime snapshot to
return the correct result to the user.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1Tzp
-----END PGP SIGNATURE-----
Merge tag 'full-dynticks-cputime-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into sched/core
Pull full-dynticks (user-space execution is undisturbed and
receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready,
from Frederic Weisbecker:
"This implements the cputime accounting on full dynticks CPUs.
Typical cputime stats infrastructure relies on the timer tick and
its periodic polling on the CPU to account the amount of time
spent by the CPUs and the tasks per high level domains such as
userspace, kernelspace, guest, ...
Now we are preparing to implement full dynticks capability on
Linux for Real Time and HPC users who want full CPU isolation.
This feature requires a cputime accounting that doesn't depend
on the timer tick.
To implement it, this new cputime infrastructure plugs into
kernel/user/guest boundaries to take snapshots of cputime and
flush these to the stats when needed. This performs pretty
much like CONFIG_VIRT_CPU_ACCOUNTING except that context location
and cputime snaphots are synchronized between write and read
side such that the latter can safely retrieve the pending tickless
cputime of a task and add it to its latest cputime snapshot to
return the correct result to the user."
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Ingo Molnar:
"Three small fixlets"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel/cacheinfo: Shut up annoying warning
x86, doc: Boot protocol 2.12 is in 3.8
x86-64: Replace left over sti/cli in ia32 audit exit code
Pull perf fixes from Ingo Molnar:
"Three fixlets and two small (and low risk) hw-enablement changes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix event group context move
x86/perf: Add IvyBridge EP support
perf/x86: Fix P6 driver section warning
arch/x86/tools/insn_sanity.c: Identify source of messages
perf/x86: Enable Intel Lincroft/Penwell/Cloverview Atom support
The IRQ_PER_CPU Kconfig symbol was removed in the following commit:
Commit 6a58fb3bad ("genirq: Remove
CONFIG_IRQ_PER_CPU") merged in v2.6.39-rc1.
But IRQ_PER_CPU wasn't removed from any of the architecture Kconfig
files where it was defined or selected. It's completely unused so remove
the remaining references.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <uclinux-dist-devel@blackfin.uclinux.org>
Cc: <linux-mips@linux-mips.org>
Cc: <linuxppc-dev@lists.ozlabs.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Link: http://lkml.kernel.org/r/1359972583-17134-1-git-send-email-james.hogan@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unfortunately, this name conflicts with a different use of
the name in various places through the tree, so don't provide
it for the kernel. We preserve it for userspace to avoid
breaking any userspace code that relies on this definition.
This fixes a number of compile errors for various drivers that
are enabled by "allyesconfig".
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
I've been getting the following warning when doing randbuilds
since forever. Now it finally pissed me off just the perfect
amount so that I can fix it.
arch/x86/kernel/cpu/intel_cacheinfo.c:489:27: warning: ‘cache_disable_0’ defined but not used [-Wunused-variable]
arch/x86/kernel/cpu/intel_cacheinfo.c:491:27: warning: ‘cache_disable_1’ defined but not used [-Wunused-variable] arch/x86/kernel/cpu/intel_cacheinfo.c:524:27: warning: ‘subcaches’ defined but not used [-Wunused-variable]
It happens because in randconfigs where CONFIG_SYSFS is not set,
the whole sysfs-interface to L3 cache index disabling is
remaining unused and gcc correctly warns about it. Make it
optional, depending on CONFIG_SYSFS too, as is the case with
other sysfs-related machinery in this file.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Link: http://lkml.kernel.org/r/1359969195-27362-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull powerpc update from Benjamin Herrenschmidt:
"Just so that you don't get too bored on your Island here's a patch for
3.8 fixing a nasty bug that affects the new 64T support that was
merged in 3.7. Please apply whenever you have a chance (and an
internet connection!)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix hash computation function
The ASM version of hash computation function was truncating the upper bit.
Make the ASM version similar to hpt_hash function. Remove masking vsid bits.
Without this patch, we observed hang during bootup due to not satisfying page
fault request correctly. The fault handler used wrong hash values to update
the HPTE. Hence we kept looping with page fault.
hash_page(ea=000001003e260008, access=203, trap=300 ip=3fff91787134 dsisr 42000000
The computed value of hash 000000000f22f390
update: avpnv=4003e46054003e00, hash=000000000722f390, f=80000006, psize: 2 ...
BenH: The over-masking has been there for ever but only hurts with the
new 64T support introduced in 3.7
Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Tested-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.7]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRCxWdAAoJEHm+PkMAQRiG3bAH/28D2NbRLIDo6QIzk3seCCh3
A6vqDWbX671JRa0RO38DrWhqv6L/EisvjNZMVxBNaN635+3+yC7wsKziXYxA4+AL
Ef9JISiwXykRWwrC8Q34YBWfWgeFTmaau71IRv45x2OTwiijd6cvjXhLDrOhHEGL
rdAGJxIdBOfuASw1zpn9PxzfAtg1j/FGP03B4yy+JFhYzuDp3pvnDIysAnXefLml
UheuBELdNf8Jx7NtW80PTa+TQtruWPC8otoiJevV4TrAWmAOctJiM1izL+VOZqqD
I/v5aGf9mCN+cxLq06imwgEHWmP1I7yDdjjTHrr4wwIMws1vg8PNsJqG3AsPcwM=
=dR8S
-----END PGP SIGNATURE-----
Merge tag 'v3.8-rc6' into x86/urgent
Linux 3.8-rc6
Merged in order to add a documentation update versus new code in
upstream.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull MIPS updates from Ralf Baechle:
"A number of fixes all across the MIPS tree. No area is particularly
standing out and things have cooled down quite nicely for a release."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Function tracer: Fix broken function tracing
mips: Move __virt_addr_valid() to a place for MIPS 64
MIPS: Netlogic: Fix UP compilation on XLR
MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
MIPS: AR724x: Fix AR724X_PCI_MEM_SIZE
MIPS: Lantiq: Fix cp0_perfcount_irq mapping
MIPS: DSP: Fix DSP mask for registers.
MIPS: Fix build failure by adding definition of pfn_pmd().
MIPS: Octeon: Fix warning.
MIPS: delay.c: Check BITS_PER_LONG instead of __SIZEOF_LONG__
MIPS: PNX833x: Fix comment.
MIPS: Add struct p_format to union mips_instruction.
MIPS: Export <asm/break.h>.
MIPS: BCM47xx: Enable SSB prerequisite SSB_DRIVER_PCICORE.
MIPS: BCM47xx: Select GPIOLIB for BCMA on bcm47xx platform
MIPS: vpe.c: Fix null pointer dereference in print arguments.
With commit a0ae0240 (ARM: kernel: add device tree init map function),
the cpu id value may include the cluster id and is no longer 0-3, so we
need to mask it now to get the right hard cpu index.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
With commit a0ae0240 (ARM: kernel: add device tree init map function),
the cpu id value may include the cluster id and is no longer 0-3, so we
need to mask it in scu_power_mode to get the local cpu number. Since we
are only dealing with the cpu we are running on, the cluster id should
not ever be needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Add an empty version of scu_enable for !SMP builds. This fixes
compile error for highbank suspend code on !SMP builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Make some POWER7-specific perf events available in sysfs.
$ /bin/ls -1 /sys/bus/event_source/devices/cpu/events/
branch-instructions
branch-misses
cache-misses
cache-references
cpu-cycles
instructions
PM_BRU_FIN
PM_BRU_MPRED
PM_CMPLU_STALL
PM_CYC
PM_GCT_NOSLOT_CYC
PM_INST_CMPL
PM_LD_MISS_L1
PM_LD_REF_L1
stalled-cycles-backend
stalled-cycles-frontend
where the 'PM_*' events are POWER specific and the others are the
generic events.
This will enable users to specify these events with their symbolic
names rather than with their raw code.
perf stat -e 'cpu/PM_CYC' ...
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062528.GE13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Make the generic perf events in POWER7 available via sysfs.
$ ls /sys/bus/event_source/devices/cpu/events
branch-instructions
branch-misses
cache-misses
cache-references
cpu-cycles
instructions
stalled-cycles-backend
stalled-cycles-frontend
$ cat /sys/bus/event_source/devices/cpu/events/cache-misses
event=0x400f0
This patch is based on commits that implement this functionality on x86.
Eg:
commit a47473939d
Author: Jiri Olsa <jolsa@redhat.com>
Date: Wed Oct 10 14:53:11 2012 +0200
perf/x86: Make hardware event translations available in sysfs
Changelog:[v2]
[Jiri Osla] Drop EVENT_ID() macro since it is only used once.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062454.GD13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Rename EVENT_ATTR() to PMU_EVENT_ATTR() and make it global so it is
available to all architectures.
Further to allow architectures flexibility, have PMU_EVENT_ATTR() pass
in the variable name as a parameter.
Changelog[v2]
- [Jiri Olsa] No need to define PMU_EVENT_PTR()
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062422.GC13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Define and use macros to identify perf events codes This would make it
easier and more readable when these event codes need to be used in more
than one place.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062353.GB13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Function tracing is currently broken for all 32 bit MIPS platforms.
When tracing is enabled, the kernel immediately hangs on boot.
This is a result of commit b732d439cb
that changes the kernel/trace/Kconfig file so that is no longer
forces FRAME_POINTER when FUNCTION_TRACING is enabled.
MIPS frame pointers are generally considered to be useless because
they cannot be used to unwind the stack. Unfortunately the MIPS
function tracing code has bugs that are masked by the use of frame
pointers. This commit fixes the bugs so that MIPS frame pointers
don't need to be enabled.
The bugs are a result of the odd calling sequence used to call the trace
routine. This calling sequence is inserted into every traceable function
when the tracing CONFIG option is enabled. This sequence is generated
for 32bit MIPS platforms by the compiler via the "-pg" flag.
Part of the sequence is "addiu sp,sp,-8" in the delay slot after every
call to the trace routine "_mcount" (some legacy thing where 2 arguments
used to be pushed on the stack). The _mcount routine is expected to
adjust the sp by +8 before returning. So when not disabled, the original
jalr and addiu will be there, so _mcount has to adjust sp.
The problem is that when tracing is disabled for a function, the
"jalr _mcount" instruction is replaced with a nop, but the
"addiu sp,sp,-8" is still executed and the stack pointer is left
trashed. When frame pointers are enabled the problem is masked
because any access to the stack is done through the frame
pointer and the stack pointer is restored from the frame pointer when
the function returns.
This patch writes two nops starting at the address of the "jalr _mcount"
instruction whenever tracing is disabled. This means that the
"addiu sp,sp.-8" will be converted to a nop along with the "jalr". When
disabled, there will be two nops.
This is SMP safe because the first time this happens is during
ftrace_init() which is before any other processor has been started.
Subsequent calls to enable/disable tracing when other CPUs ARE running
will still be safe because the enable will only change the first nop
to a "jalr" and the disable, while writing 2 nops, will only be changing
the "jalr". This patch also stops using stop_machine() to call the
tracer enable/disable routines and calls them directly because the
routines are SMP safe.
When the kernel first boots we have to be able to handle the gcc
generated jalr, addui sequence until ftrace_init gets a chance to run
and change the sequence. At this point mcount just adjusts the stack
and returns. When ftrace_init runs, we convert the jalr/addui to nops.
Then whenever tracing is enabled we convert the first nop to a "jalr
mcount+8". The mcount+8 entry point skips the stack adjust.
[ralf@linux-mips.org: Folded in Steven Rostedt's build fix.]
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: rostedt@goodmis.org
Cc: ddaney.cavm@gmail.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4806/
Patchwork: https://patchwork.linux-mips.org/patch/4841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit d3ce884318 "MIPS: Fix modpost error in modules attepting to use
virt_addr_valid()" moved __virt_addr_valid() from a macro in a header
file to a function in ioremap.c. But ioremap.c is only compiled for MIPS
32, and not for MIPS 64.
When compiling for my yeeloong2, which supposedly supports hibernation,
which compiles kernel/power/snapshot.c which calls virt_addr_valid(), I
got this error:
LD init/built-in.o
kernel/built-in.o: In function `memory_bm_free':
snapshot.c:(.text+0x4c9c4): undefined reference to `__virt_addr_valid'
snapshot.c:(.text+0x4ca58): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e44c): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e890): undefined reference to `__virt_addr_valid'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
I suspect that __virt_addr_valid() is fine for mips 64. I moved it to
mmap.c such that it gets compiled for mips 64 and 32.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since ed4f209 "s390/time: fix sched_clock() overflow" a new helper function
is used to avoid overflows when converting TOD format values to nanosecond
values.
The kvm interrupt code formerly however only worked by accident because of
an overflow. It tried to program a timer that would expire in more than ~29
years. Because of the old TOD-to-nanoseconds overflow bug the real expiry
value however was much smaller, but now it isn't anymore.
This however triggers yet another bug in the function that programs the clock
comparator s390_next_ktime(): if the absolute "expires" value is after 2042
this will result in an overflow and the programmed value is lower than the
current TOD value which immediatly triggers a clock comparator (= timer)
interrupt.
Since the timer isn't expired it will be programmed immediately again and so
on... the result is a dead system.
To fix this simply program the maximum possible value if an overflow is
detected.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: stable@vger.kernel.org # v3.3+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
For some reason they didn't get replaced so far by their
paravirt equivalents, resulting in code to be run with
interrupts disabled that doesn't expect so (causing, in the
observed case, a BUG_ON() to trigger) when syscall auditing is
enabled.
David (Cc-ed) came up with an identical fix, so likely this can
be taken to count as an ack from him.
Reported-by: Peter Moody <pmoody@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/5108E01902000078000BA9C5@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Tested-by: Peter Moody <pmoody@google.com>
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QrJx
-----END PGP SIGNATURE-----
Merge tag 'efi-for-3.8' into x86/efi
Various urgent EFI fixes and some warning cleanups for v3.8
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The commit 2a37b1a "MIPS: Netlogic: Move from u32 cpumask to cpumask_t"
breaks uniprocessor compilation on XLR with:
arch/mips/netlogic/xlr/setup.c: In function 'prom_init':
arch/mips/netlogic/xlr/setup.c:196:6: error: unused variable 'i'
Fix by defining 'i' only when CONFIG_SMP is defined.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4760/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The base address of the PCI memory is 0x10000000 and the base address of the
PCI configuration space is 0x17000000 on the AR71xx SoCs.
The AR71XX_PCI_MEM_SIZE is defined as 0x08000000 which is wrong because that
overlaps with the configuration space. This patch fixes the value of the
AR71XX_PCI_MEM_SIZE constant, in order to avoid this resource conflicts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4873/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The base address of the PCI memory is
0x10000000 and the base address of the
PCI configuration space is 0x14000000
on the AR724x SoCs.
The AR724X_PCI_MEM_SIZE is defined as
0x08000000 which is wrong because that
overlaps with the configuration space.
The patch fixes the value of the
AR724X_PCI_MEM_SIZE constant, in order
to avoid this resource conflicts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4872/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The introduction of the OF support broke the cp0_perfcount_irq mapping. This
resulted in oprofile not working anymore.
Offending commit is :
commit 3645da0276
Author: John Crispin <blogic@openwrt.org>
Date: Tue Apr 17 10:18:32 2012 +0200
OF: MIPS: lantiq: implement irq_domain support
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4875/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull one s390 fix from Martin Schwidefsky:
"Another transparent huge page fix, we need to define a s390 variant
for pmdp_set_wrprotect to flush the TLB for the huge page correctly."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/thp: implement pmdp_set_wrprotect()
Jason pointed out the HAS_PERSISTENT_CLOCK name isn't
quite accurate for the config, as some systems may have
the persistent_clock in some cases, but not always.
So change the config name to the more clear
ALWAYS_USE_PERSISTENT_CLOCK.
Signed-off-by: John Stultz <john.stultz@linaro.org>
It looks like the original commit that copied the rom contents from
efi always copied the rom, and the fixup in setup_efi_pci from commit
886d751a2e ("x86, efi: correct precedence of operators in
setup_efi_pci") broke that.
This resulted in macbook pro's no longer finding the rom images, and
thus not being able to use the radeon card any more.
The solution is to just remove the check for now, and always copy the
rom if available.
Reported-by: Vitaly Budovski <vbudovski+news@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Use the new sentinel field to detect bootloaders which fail to follow
protocol and don't initialize fields in struct boot_params that they
do not explicitly initialize to zero.
Based on an original patch and research by Yinghai Lu.
Changed by hpa to be invoked both in the decompression path and in the
kernel proper; the latter for the case where a bootloader takes over
decompression.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
These patches move all interrupt remapping specific checks out of the
x86 core code and replaces the respective call-sites with function
pointers. As a result the interrupt remapping code is better abstraced
from x86 core interrupt handling code.
The code was rebased to v3.8-rc4 and tested on systems with AMD-Vi and
Intel VT-d (both capable of interrupt remapping). The systems were
tested with IOMMU enabled and with IOMMU disabled. No issues were found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRBpGoAAoJECvwRC2XARrjxn4P/2sNpncRptR37HBP4Dl+Rd+u
lnp9agUzzHQ67j+1o4bYGknhgfxGqDHJKNW41AinciE1EiyX1QAdFUK1mNEmtRrL
dgsoZZdZjKIlNU8rsTon18UJvUT8wR9s8I/+DAVzO5WkRbCQWQ0kC9Ft4QQSKIfs
M0dg8eAauIGp7/UsmttZIY9PT1KOhMWPDAaCsEYSLgfXO3VzXNtlZIjQI8bQJhSs
DLCoge7bHfUIk13p5WM73qMFDXEXNkHgTDqMjXYB9uJiHSWyGg1vs2dV5rc0fbHQ
KBin1NwFwT2HveMlGVy1DVgbdDEy5e7uvPnyHIwI6JedAA2MxYqOsL/VbLnRCgvt
OH3bHoGrBJDBEwv/tleyf8SyJ6TO4px6TlOzUlIHHu+33Bc0uKigKXLuXwvTus0q
3cP++X6jW2yn0f65Lpr7LTu/02FRaKMvHWpU1T7yc+rXwJREn1/0bEdYC/fb1u3N
GT2aI2orlGMwLtJ1mcxbveKWBnPN5RBrOe0Zha6ycVw7aJol2fAIczSnUq/6SHDQ
eFXS7nMqb2J5p8IgQbB5wHDovsqWEBbGC9bEYkjxQEjqD8YgLnIHDR4KgRzhFI1f
LX19+wsBkxzwQX8sImEaKzWMoSAl0Sui01s0tc7nJkwfhnbMhIes7pfqkUx0d4ZM
AK0It3VSCw4hCnCUC+b2
=2d89
-----END PGP SIGNATURE-----
Merge tag 'ioapic-cleanups-for-tip' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu into x86/apic
Pull "x86 IOAPIC code from interrupt remapping details cleanups" from
Joerg Roedel:
"These patches move all interrupt remapping specific checks out of the
x86 core code and replaces the respective call-sites with function
pointers. As a result the interrupt remapping code is better abstraced
from x86 core interrupt handling code.
The code was rebased to v3.8-rc4 and tested on systems with AMD-Vi and
Intel VT-d (both capable of interrupt remapping). The systems were
tested with IOMMU enabled and with IOMMU disabled. No issues were found."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With commit:
4cca6ea04d ("x86/apic: Allow x2apic without IR on VMware platform")
we started seeing "incompatible initialization" warning messages,
since x2apic_available() expects a bool return type while
kvm_para_available() returns an int.
Reported by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
xtensa/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
For architectures using dma_map_ops, dma_mmap_coherent() and
dma_get_sgtable() are provided in <asm-generic/dma-mapping-common.h>.
Xtensa does not use dma_map_ops, hence it should implement them itself.
For now, use dummy implementations that just return -EINVAL, until the API
has been finalized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-xtensa@linux-xtensa.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
parisc/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
For architectures using dma_map_ops, dma_mmap_coherent() and
dma_get_sgtable() are provided in <asm-generic/dma-mapping-common.h>.
Parisc does not use dma_map_ops, hence it should implement them itself.
For now, use dummy implementations that just return -EINVAL, until the
API has been finalized, as it cannot be supported on PA-RISC as-is.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
mn10300/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
For architectures using dma_map_ops, dma_mmap_coherent() and
dma_get_sgtable() are provided in <asm-generic/dma-mapping-common.h>.
Mn10300 does not use dma_map_ops, hence it should implement them itself.
For now, use dummy implementations that just return -EINVAL, until the API
has been finalized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-am33-list@redhat.com
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
m68k/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
For architectures using dma_map_ops, dma_mmap_coherent() and
dma_get_sgtable() are provided in <asm-generic/dma-mapping-common.h>.
M68k does not use dma_map_ops, hence it should implement them as inline
stubs using dma_common_mmap() and dma_common_get_sgtable().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
frv/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
For architectures using dma_map_ops, dma_mmap_coherent() and
dma_get_sgtable() are provided in <asm-generic/dma-mapping-common.h>.
Frv does not use dma_map_ops, hence it should implement them itself.
For now, use dummy implementations that just return -EINVAL, until the API
has been finalized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
cris/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
For architectures using dma_map_ops, dma_mmap_coherent() and
dma_get_sgtable() are provided in <asm-generic/dma-mapping-common.h>.
Cris does not use dma_map_ops, hence it should implement them as inline
stubs using dma_common_mmap() and dma_common_get_sgtable().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-cris-kernel@axis.com
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
c6x/allmodconfig (assumed):
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
For architectures using dma_map_ops, dma_mmap_coherent() and
dma_get_sgtable() are provided in <asm-generic/dma-mapping-common.h>.
C6x does not use dma_map_ops, hence it should implement them itself.
For now, use dummy implementations that just return -EINVAL, until the API
has been finalized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-c6x-dev@linux-c6x.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
blackfin/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
For architectures using dma_map_ops, dma_mmap_coherent() and
dma_get_sgtable() are provided in <asm-generic/dma-mapping-common.h>.
Blackfin does not use dma_map_ops, hence it should implement them as inline
stubs using dma_common_mmap() and dma_common_get_sgtable().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
avr32/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
For architectures using dma_map_ops, dma_mmap_coherent() and
dma_get_sgtable() are provided in <asm-generic/dma-mapping-common.h>.
Avr32 does not use dma_map_ops, hence it should implement them as inline
stubs using dma_common_mmap() and dma_common_get_sgtable().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Add MOVBE to asm/required-features.h so we check for it during startup
and don't bother checking for it later.
CONFIG_MATOM is used because it corresponds to -march=atom in the
Makefiles. If the rules get more complicated it may be necessary to
make this an explicit Kconfig option which uses -mmovbe/-mno-movbe to
control the use of this instruction explicitly.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Link: http://lkml.kernel.org/r/1359395390.3529.65.camel@shinybook.infradead.org
[ hpa: added a patch description ]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
With lazy interrupt, we always call __check_irq_replaysome with
decrementers_next_tb to check if we need to replay timer interrupt.
So in hotplug case we also need to set decrementers_next_tb as MAX
to make sure __check_irq_replay don't replay timer interrupt
when return as we expect, otherwise we'll trap here infinitely.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
the variable backup_current_thread_info isn't freed before existing the
function.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In preempt case current arch_local_irq_restore() from
preempt_schedule_irq() may enable hard interrupt but we really
should disable interrupts when we return from the interrupt,
and so that we don't get interrupted after loading SRR0/1.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The calculation for the left shift of the mask OPROFILE_PM_PMCSEL_MSK has an
error. The calculation is should be to shift left by (max_cntrs - cntr) times
the width of the pmsel field width. However, the #define OPROFILE_MAX_PMC_NUM
was used instead of OPROFILE_PMSEL_FIELD_WIDTH. This patch fixes the
calculation.
Signed-off-by: Carl Love <cel@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit f96972f2dc "kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()"
added a call to disable_nonboot_cpus() on kernel_restart(), which tries
to shutdown all the CPUs except the first one. The issue with the PA
Semi, is that it does not support CPU hotplug.
When the call is made to __cpu_down(), it calls the notifiers
CPU_DOWN_PREPARE, and then tries to take the CPU down.
One of the notifiers to the CPU hotplug code, is the cpufreq. The
DOWN_PREPARE will call __cpufreq_remove_dev() which calls
cpufreq_driver->exit. The PA Semi exit handler unmaps regions of I/O
that is used by an interrupt that goes off constantly
(system_reset_common, but it goes off during normal system operations
too). I'm not sure exactly what this interrupt does.
Running a simple function trace, you can see it goes off quite a bit:
# tracer: function
#
# TASK-PID CPU# TIMESTAMP FUNCTION
# | | | | |
<idle>-0 [001] 1558.859363: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.860112: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.861109: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [001] 1558.861361: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.861437: .pasemi_system_reset_exception <-.system_reset_exception
When the region is unmapped, the system crashes with:
Disabling non-boot CPUs ...
Error taking CPU1 down: -38
Unable to handle kernel paging request for data at address 0xd0000800903a0100
Faulting instruction address: 0xc000000000055fcc
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=64 NUMA PA Semi PWRficient
Modules linked in: shpchp
NIP: c000000000055fcc LR: c000000000055fb4 CTR: c0000000000df1fc
REGS: c0000000012175d0 TRAP: 0300 Not tainted (3.8.0-rc4-test-dirty)
MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR: 24000088 XER: 00000000
SOFTE: 0
DAR: d0000800903a0100, DSISR: 42000000
TASK = c0000000010e9008[0] 'swapper/0' THREAD: c000000001214000 CPU: 0
GPR00: d0000800903a0000 c000000001217850 c0000000012167e0 0000000000000000
GPR04: 0000000000000000 0000000000000724 0000000000000724 0000000000000000
GPR08: 0000000000000000 0000000000000000 0000000000000001 0000000000a70000
GPR12: 0000000024000080 c00000000fff0000 ffffffffffffffff 000000003ffffae0
GPR16: ffffffffffffffff 0000000000a21198 0000000000000060 0000000000000000
GPR20: 00000000008fdd35 0000000000a21258 000000003ffffaf0 0000000000000417
GPR24: 0000000000a226d0 c000000000000000 0000000000000000 0000000000000000
GPR28: c00000000138b358 0000000000000000 c000000001144818 d0000800903a0100
NIP [c000000000055fcc] .set_astate+0x5c/0xa4
LR [c000000000055fb4] .set_astate+0x44/0xa4
Call Trace:
[c000000001217850] [c000000000055fb4] .set_astate+0x44/0xa4 (unreliable)
[c0000000012178f0] [c00000000005647c] .restore_astate+0x2c/0x34
[c000000001217980] [c000000000054668] .pasemi_system_reset_exception+0x6c/0x88
[c000000001217a00] [c000000000019ef0] .system_reset_exception+0x48/0x84
[c000000001217a80] [c000000000001e40] system_reset_common+0x140/0x180
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32,
which is similar to commit 12660b17.
Reported-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With -mmovbe enabled (implicit with -march=atom), this allows the
compiler to use the movbe instruction. This doesn't have a significant
effect on code size (unlike on PowerPC), because the movbe instruction
actually takes as many bytes to encode as a simple mov and a bswap. But
for Atom in particular I believe it should give a performance win over
the mov+bswap alternative. That was kind of why movbe was invented in
the first place, after all...
I've done basic functionality testing with IPv6 and Legacy IP, but no
performance testing. The EFI firmware on my test box unfortunately no
longer starts up.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Link: http://lkml.kernel.org/r/1355966180.18919.102.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The irq_remapped function is only used in IOMMU code after
the last patch. So move its definition there too.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This callback replaces the old __eoi_ioapic_pin function
which needs a special path for interrupt remapping.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This call-back points to the right function for initializing
the msi_msg structure. The old code for msi_msg generation
was split up into the irq-remapped and the default case.
The irq-remapped case just calls into the specific Intel or
AMD implementation when the device is behind an IOMMU.
Otherwise the default function is called.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function does irq-remapping specific interrupt setup
like modifying the chip defaults.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The function is called unconditionally now in IO-APIC code
removing another irq_remapped() check from x86 core code.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function is only called from default_ioapic_set_affinity()
which is only used when interrupt remapping is disabled
since the introduction of the set_affinity function pointer.
So the check will always evaluate as true and can be
removed.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Move all the code to either to the header file
asm/irq_remapping.h or to drivers/iommu/.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add a data structure to store information the IOMMU driver
can use to get from a 'struct irq_cfg' to the remapping
entry.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Remove the last left-over from this flag from x86 code.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function is only called when irq-remapping is disabled.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Move these checks to IRQ remapping code by introducing the
panic_on_irq_remap() function.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This pointer is changed to a different function when IRQ
remapping is enabled.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
With interrupt remapping a special function is used to
change the affinity of an IO-APIC interrupt. Abstract this
with a function pointer.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Use seperate routines to setup MSI IRQs for both
irq_remapping_enabled cases.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function pointer can be overwritten by the IRQ
remapping code. The irq_remapping_enabled check can be
removed from default_setup_hpet_msi.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This call-back is used to dump IO-APIC entries for debugging
purposes into the kernel log. VT-d needs a special routine
for this and will overwrite the default.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function pointer is used to call a system-specific
function for disabling the IO-APIC. Currently this is used
for IRQ remapping which has its own disable routine.
Also introduce the necessary infrastructure in the interrupt
remapping code to overwrite this and other function pointers
as necessary by interrupt remapping.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
IO-APIC and PIC use the same resume routines when IRQ
remapping is enabled or disabled. So it should be safe to
mask the other APICs for the IRQ-remapping-disabled case
too.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Move the three easy to move checks in the x86' apic.c file
into the IRQ-remapping code.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We have historically hard-coded entry points in head.S just so it's easy
to build the executable/bzImage headers with references to them.
Unfortunately, this leads to boot loaders abusing these "known" addresses
even when they are *explicitly* told that they "should look at the ELF
header to find this address, as it may change in the future". And even
when the address in question *has* actually been changed in the past,
without fanfare or thought to compatibility.
Thus we have bootloaders doing stunningly broken things like jumping
to offset 0x200 in the kernel startup code in 64-bit mode, *hoping*
that startup_64 is still there (it has moved at least once
before). And hoping that it's actually a 64-bit kernel despite the
fact that we don't give them any indication of that fact.
This patch should hopefully remove the temptation to abuse internal
addresses in future, where sternly worded comments have not sufficed.
Instead of having hard-coded addresses and saying "please don't abuse
these", we actually pull the addresses out of the ELF payload into
zoffset.h, and make build.c shove them back into the right places in
the bzImage header.
Rather than including zoffset.h into build.c and thus having to rebuild
the tool for every kernel build, we parse it instead. The parsing code
is small and simple.
This patch doesn't actually move any of the interesting entry points, so
any offending bootloader will still continue to "work" after this patch
is applied. For some version of "work" which includes jumping into the
compressed payload and crashing, if the bzImage it's given is a 32-bit
kernel. No change there then.
[ hpa: some of the issues in the description are addressed or
retconned by the 2.12 boot protocol. This patch has been edited to
only remove fixed addresses that were *not* thus retconned. ]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
The 'Attributes' argument to pci->Attributes() function is 64-bit. So
when invoking in 32-bit mode it takes two registers, not just one.
This fixes memory corruption when booting via the 32-bit EFI boot stub.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
If the bootloader calls the EFI handover entry point as a standard function
call, then it'll have a return address on the stack. We need to pop that
before calling efi_main(), or the arguments will all be out of position on
the stack.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
When booting under OVMF we have precisely one GOP device, and it
implements the ConOut protocol.
We break out of the loop when we look at it... and then promptly abort
because 'first_gop' never gets set. We should set first_gop *before*
breaking out of the loop. Yes, it doesn't really mean "first" any more,
but that doesn't matter. It's only a flag to indicate that a suitable
GOP was found.
In fact, we'd do just as well to initialise 'width' to zero in this
function, then just check *that* instead of first_gop. But I'll do the
minimal fix for now (and for stable@).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Define the 2.12 bzImage boot protocol: add xloadflags and additional
fields to allow the command line, initramfs and struct boot_params to
live above the 4 GiB mark.
The xloadflags now communicates if this is a 64-bit kernel with the
legacy 64-bit entry point and which of the EFI handover entry points
are supported.
Avoid adding new read flags to loadflags because of claimed
bootloaders testing the whole byte for == 1 to determine bzImageness
at least until the issue can be researched further.
This is based on patches by Yinghai Lu and David Woodhouse.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Originally-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Chris Metcalf