When resetting the ECC registers/counters, the bit will automatically
clear itself once the reset has actually finished. So make sure we
wait for that to occur before doing anything else rather than assuming
everything is peachy and proceeding with stale ECC values.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We used the platform rd_dly field when we meant to use the wr_dly field.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND base may send some controls which are neither CLE nor ALE, so
we need to explicitly check both instead of assuming things are always
one or the other. Otherwise, we sometimes send out illegal addresses
to the NAND device.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Our write_buf/read_buf funcs always do ECC in HW ECC mode. That is not
needed for raw funcs. In fact, write_buf/read_buf should be a pure func
for data input/output while chip->ecc.hwctl controls ECC. Unfortunately,
we can't separate ECC from normal data input/output in our NFC, so our DMA
write_buf/read_buf entries are coupled with ECC operations closely.
Thus we need to provide dedicated read_page_raw/write_page_raw funcs where
we do non-DMA transactions so as to avoid automatic ECC.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The low level NAND driver doesn't care about filesystems, so punt the
local comment indicating otherwise.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
spi_write_then_read() may return its own return codes (e.g. -EIO),
so let's propagate the value down to the probe().
Also, remove jedec == 0 check, it isn't needed as nowadays we use
dedicated SPI device IDs for non-JEDEC flashes.
Suggested-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since commit 18c6182bae ("Rework
probing/JEDEC code"), m25p80 driver successfully registers chips
even if JEDEC probing fails.
This was needed to support non-JEDEC flashes. Though, it appears
that some platforms (e.g. blackfin bf533 stamp[1]) used the old
behavior to detect if there's any flash connected, so the driver
have to fail on JEDEC probing errors.
This patch restores the old behavior for JEDEC flashes, and adds
"-nonjedec" SPI device IDs for M25Pxx flashes, so that the kernel
still supports non-JEDEC flashes.
[1] http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=5975
Reported-by: Mingquan Pan
Reported-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For no-mmu systems mmap() on RAM/ROM devices already works
but for systems with mmu it probably was not tested and
doesn't work.
This patch allows using mmap() on MTD RAM/ROM devices on systems
with MMU. It has been tested on mpc5121e based platform with
MR0A16A MRAM device attached over LocalBus.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for static flash partitioning from a platform
device. Also, we clean up some weirdness where statements were separated
by commas instead of semicolons. While we are at it, fix some minor bad
white space, too.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The mtd layer is responsible to call mtd->{suspend,resume}. Doing it
again in the driver is wrong and results in a warning:
nand_resume called for a chip which is not in suspended state
at resume time. Removing the calls from the resume and suspend
functions makes them empty allowing them to be deleted completely.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The variable 'syn' was being used uninitialized. Also
fixed incorrect use of syn[] vs s[].
Tested on powerpc board with 64MiB DOC2000.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Samsung SoCs use own chip_probe function.
Don't touch the memory configuration at probe time.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Samsung SoCs use the own OneNAND controler and detect OneNAND chip at power on.
To use this feature, introduce the chip_probe function.
Also remove workaround for Samsung SoCs.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sending the patch for page address calculation based on device type. This resolves the
OneNAND DDP device read problem as pointed by Enric.
http://lists.infradead.org/pipermail/linux-mtd/2010-July/030920.html
Signed-off-by: Rohit HS <rohit.hs@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is an update that depends on the previous patches I sent.
We can now write to all the appropriate BB marker locations (i.e.
pages 1 AND 2, bytes 1 AND 6) with nand_default_block_markbad() if
necessary, according to the flags marked in chip->options.
Note that I removed the line:
ofs += mtd->oobsize;
Unless I am wrong, this line was completely unnecessary in the
first place.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix all checkpatch.pl complaints.
Artem: tweaked a little and fix tab indentations, so now this is not
only about checkpatch, but also about making indentations look
sane.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On TI's DA830/OMAP-L137, DA850/OMAP-L138 and DM365, after setting the
4BITECC_ADD_CALC_START bit in the NAND Flash control register to 1 and
before waiting for the NAND Flash status register to be equal to 1, 2 or
3, we have to wait till the ECC HW goes to correction state. Without this
wait, ECC correction calculations will not be proper.
This has been tested on DA830/OMAP-L137, DA850/OMAP-L138, DM355 and DM365
EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a revision to PATCH 2/2 that I sent. Link:
http://lists.infradead.org/pipermail/linux-mtd/2010-July/030911.html
Added new flag for scanning of both bytes 1 and 6 of the OOB for
a BB marker (instead of simply one or the other).
The "check_pattern" and "check_short_pattern" functions were updated
to include support for scanning the two different locations in the OOB.
In order to handle increases in variety of necessary scanning patterns,
I implemented dynamic memory allocation of nand_bbt_descr structs
in new function 'nand_create_default_bbt_descr()'. This replaces
some increasingly-unwieldy, statically-declared descriptors. It can
replace several more (e.g. "flashbased" structs). However, I do not
test the flashbased options personally.
How this was tested:
I referenced 30+ data sheets (covering 100+ parts), and I tested a
selection of 10 different chips to varying degrees. Particularly, I
tested the creation of bad-block descriptors and basic BB scanning on
three parts:
ST NAND04GW3B2D, 2K page
ST NAND128W3A, 512B page
Samsung K9F1G08U0A, 2K page
To test these, I wrote some fake bad block markers to the flash (in OOB
bytes 1, 6, and elsewhere) to see if the scanning routine would detect
them properly. However, this method was somewhat limited because the
driver I am using has some bugs in its OOB write functionality.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some level of support for various scanning locations was already built in,
but this required clean-up. First, BB marker location cannot be determined
_only_ by the page size. Instead, I implemented some heuristic detection
based on data sheets from various manufacturers (all found in
nand_base.c:nand_get_flash_type()).
Second, once these options were identified, they were not handled properly
by nand_bbt.c:nand_default_bbt(). I updated the static nand_bbt_desc structs
to reflect the need for more combinations of detection. The memory allocation
here probably needs to be done dynamically in the very near future (see next
patches).
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Current driver prevents command-line partitions from being parsed when built-in
partitions are defined in s3c2410_nand_set object, but it is not desirable in some
cases. This patch tries to parse commad-line partitions prior to the built-in.
Signed-off-by: Conke Hu <conke@maxwit.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
NAND_BB_LAST_PAGE used to be in nand.h, but it pertained to bad block
management and so belongs next to NAND_BBT_SCAN2NDPAGE in bbm.h. Also,
its previous flag value (0x00000400) conflicted with NAND_BBT_SCANALLPAGES
so I changed its value to 0x00008000. All uses of the name were modified to
provide consistency with other "NAND_BBT_*" flags.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Test if a lock or unlock function is present (pointer not NULL) before
calling it, to prevent a kernel dump.
Artem: removed extra blank lines
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Included the basic size info for NAND chips with ID of 0xAD or
0xD7. The first can be found in Hynix HY27SF161G2M, while the
second can be found in Micron MT29F64G08 and the Samsung K9LBG08U0D
(among others). Also, some 64 Gbit (or larger) chips identify as
0xD7 because they contain multiple smaller 32 Gbit chips. I
assume it's safe to classify these under the 32 Gbit listing.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes:
drivers/mtd/nand/mxc_nand.c: In function 'mxcnd_resume':
drivers/mtd/nand/mxc_nand.c:901: warning: unused variable 'host'
Removing this variable was missed in 9c14b153e6.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patchs adds a way for user space programs to find out whether a
flash sector is locked. An optional driver method in the mtd_info struct
provides the information.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for Macronix 25L8005. Tested on a HP t5325 Thin Client.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There was a break missing so we returned -ENOTTY on success instead of
zero. This was introduced by 048d8719956: "mtd: blktrans: Hotplug fixes"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Look for dependency checks for "FOO" when inside of an "if FOO" block and remove them.
Signed-off-by: Kyle Spaans <kspaans@uwaterloo.ca>
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The rest of the function assumes that "data" can be null. I don't know
the code well enough to say whether it can actually be null, but there
is no harm in checking here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes build errors in drivers caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move MTD_NAND_ECC and MTD_NAND_ECC_SMC above NAND memuconfig, to unbreak
display in xconfig. This shouldn't change any dependencies.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This turns out to be the reason for DMA timeouts on resume,
if card was inserted while system was suspended
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Don't call complete on dma completion
* do a INIT_COMPLETE before using it each time
* Report DMA read error via ecc 'correct'
I finally managed to make my system do suspend to ram propertly, and I see that
if card was inserted during suspend (while system was off), I get dma timeouts
on resume. Simple card reinsert solves the issue.
This patch solves a crash that would happen otherwise
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Otherwise, if it fires right away, it might access
uninitialized spinlock
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use memdup_user when user data is immediately copied into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: misc comment fixes
UBI: fix s/then/than/ typos
UBI: init even if MTD device cannot be attached, if built into kernel
UBI: remove reboot notifier
Barry Song