Currently iwlist ethX freq[uency]/channel lists all the channels the card
supported for the current region, which includes some channels can only
be used in infrastructure mode. This patch filters these channels out if
the card is currently in ad-hoc mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When loading the ipw2200 module with disabled=1, rf_kill is activated after
every mode change. This is caused by ipw_sw_reset() is called when a mode
is changed. The patch fixed the problem by distinguishing the purposes with
the 'option' paramenter.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wpa_supplicant needs to set wpa_enabled unconditionally, with this check
it hasn't been possible to connect to non-WPA networks using wpa_supplicant.
So remove below check.
if (priv->ieee->wpa_enabled &&
network->wpa_ie_len == 0 && network->rsn_ie_len == 0)
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch does two things. It uses the parameter IW_QUAL_DBM which is new
in WE-19 to cause signal level and noise to be reported in dBm by the
wireless tools. It also defines the signal level as an unsigned integer
so that the signal level will be reported by iwlist iface scan.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace ipw2200 specific frame_hdr_len() with generic
ieee80211 routine ieee80211_get_hdrlen()
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch roll back the change we made to support for the ability to
start/stop independent Tx queues within a single net device in order to
support 802.11e QoS. We need to be able to indicate to the upper layers
that packets of a given priority can not be sent any more without halting
transmission of all packets, and without rescheduling high priority packets
down to the next priority level.
So we return NETDEV_TX_BUSY in this case and rely on the stack would
take care of rescheduling... which it apparently does immediately and
consumes the CPU. This caused the ksoftirqd kernel thread consuming almost
all the CPU...
To put the code back to the way it was before we made these changes we
put the call netif_queue_stop back in ipw_tx_skb. This effectively
disables multiple priority based transmit queues for 802.11e, but given
that its broken anyway...
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Given the amount of support requests for the meaning of the geography code
I've written a patch for printing this information on module load no matter
the debug level.
I've also added a section to the README.ipw2200 file listing the geography
codes and their meaning.
Signed-off-by: Henrik Brix Andersen <brix@gentoo.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the needlessly global function ipw_qos_current_mode()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As stated in a comment, the ipw2200 driver uses several routines that
were borrowed from ieee80211_geo.c. As ipw2200 requires ieee80211,
these routines are duplicated. The attached patch, which is sent
as an attachment to preserve whitespace, converts ipw2200.c to use
the ieee80211 versions, thereby reducing bloat in both the source
and binary.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk wrote:
> The Coverity checker spotted the following two array overflows in
> drivers/net/chelsio/sge.c (in both cases, the arrays contain 3
> elements):
[snip]
This is a bug. The array should contain 2 elements. Here is the fix.
Signed-off-by: Scott Bardone <sbardone@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
return -E_NO_BIG_ENDIAN_TESTING;
[E1000]: Fix 4 missed endianness conversions on RX descriptor fields.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olaf Hering reported a problem on pseries with e100 where ethtool -t would
cause a bus error, and the e100 driver would stop working. Due to the new
load ucode command the cb list must be allocated before calling
e100_init_hw, so remove the call and just let e100_up take care of it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
This patch moves prototypes of global variables and functions to a header
file.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: John Ronciak <john.ronciak@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker spotted this dead code (note that (clock_ctrl == 7)
is already handled above).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're leaking an skb in a failure path in this function.
Coverity #632
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Coverity checker spotted these two unused variables.
Please check whether this patch is correct or whether they should be
used.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o Make sgiseeq_dump_rings static.
o Delete unused sgiseeq_my_reset.
o Move DEBUG define to beginning where it's easier to spot and will be
seen by <linux/kernel.h> as well.
o Use NULL for pointer initialization.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert 3c509 driver to use proper suspend/resume API instead of the
deprecated pm_register/pm_unregister.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following possible updates:
- let FORCEDETH no longer depend on EXPERIMENTAL
- remove the "Reverse Engineered" from the option text:
for the user it's important which hardware the driver supports, not
how it was developed
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In latest -mm de620 gave following warning:
WARNING: drivers/net/de620.o - Section mismatch: reference to \
.init.text:de620_probe from .text between 'init_module' (at offset \
0x1682) and 'cleanup_module'
init_module() call de620_probe() which is declared __init.
Fix is to declare init_module() __init too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve reference to PCI NE2K support in ISA NE2K documentation.
Original 2.4 patch From: Ged Haywood <ged@jubileegroup.co.uk>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes an error in the dl2k driver's DMA mapping/unmapping.
The adapter uses the upper 16bits of the DMA address for the buffer
size. However, this is not masked off when referencing the DMA
address, and can lead to errors by trying to free a DMA address out of
range.
Thanks,
Jon
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For some reason, E1000's ->hard_start_xmit() routine returns -EFAULT
instead of one of the NETDEV_TX_* error codes. In fact, it frees up
the SKB before returning this. This makes the queueing layer think
the packet should be requeued and subsequently we corrupt a freed
object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turn on truncation to prevent getting choked by frames larger than expected.
Without this fix, driver hangs after receiving an oversize packet.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Avoid premature transmit ring full conditions.
Force a transmit status interrupt if transmit ring gets nearly full
and after a TSO send.
Allow more entries in transmit ring to be used if dma_addr is 32 bits
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Don't use sky2 to seed random pool beacause the network packet arrival time
will not be truly random due to NAPI and interrupt mitigation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
de_init_hw enables the irq thus it must be issued after request_irq.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Paul Rolland reported that e1000 was having a hard time using mii-tool to set speed and duplex. This patch fixes the issue on both newer hardware as well as fixing the code issue that originally caused the problem.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add DMA workaround for chips that do not support full 64-bit DMA
addresses.
5714, 5715, and 5780 chips only support DMA addresses less than 40
bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so
that pci_map_xxx() calls will map the DMA address below 40 bits if
necessary. On 64-bit systems without IOMMU, set the dma_mask to
64-bit and check for DMA addresses exceeding the limit in
tg3_start_xmit().
5788 only supports 32-bit DMA so need to set the mask appropriately
also.
Thanks to Chris Elmquist at SGI for reporting and helping to debug
the problem on 5714.
Thanks to David Miller for explaining the HIGHMEM and DMA stuff.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memset() is called before check.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Checking e100.c code against Documentation/io_ordering.txt I found the
following problem:
spin_lock_irq...
write
spin-unlock
e100_write_flush
The attached patch fix the code like this:
spin_lock_irq...
write
e100_write_flush
spin-unlock
Signed-off-by: Catalin BOIE <catab@umbrella.ro>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As documented in National application note 1287 the RX state machine on
the natsemi chip can lock up under some conditions (mostly related to
heavy load). When this happens a series of bogus packets are reported
by the chip including some oversized frames prior to the final lockup.
This patch implements the fix from the application note: when an
oversized packet is reported it resets the RX state machine, dropping
any currently pending packets.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts the natsemi driver to use NAPI. It was originally
based on one written by Harald Welte, though it has since been modified
quite a bit, most extensively in order to remove the ability to disable
NAPI since none of the other drivers seem to provide that functionality
any more.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mac_addr variable doesn't get reset between
(re)additions of multicast addresses. One byte
of all multicast addresses (except the first)
can be incorrect.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This documentation is mostly obsolete, and should therefore either be
updated or removed (this patch does the latter).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds support for the 4th port and other new features of the
BCM1480 SOC.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Originally submitted by Kenzo Iwami; his original description is:
The current bonding driver receives duplicate packets when broadcast/
multicast packets are sent by other devices or packets are flooded by the
switch. In this patch, new flags are added in priv_flags of net_device
structure to let the bonding driver discard duplicate packets in
dev.c:skb_bond().
Modified by Jay Vosburgh to change a define name, update some
comments, rearrange the new skb_bond() for clarity, clear all bonding
priv_flags on slave release, and update the driver version.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that the BIT0-BIT31 defines are no longer used by mv643xx_eth.c,
remove them from mv643xx_eth.h.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The task level rx queue refill feature hasn't ever worked
(at least in 2.6) and is of dubious value. Remove it.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify and remove redundant code for filling transmit descriptors.
No changes in features; it's just a code reorganization/cleanup.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>From : Dale Farnsworth <dale@farnsworth.org>
Recent patches for the mv643xx_eth driver now use the MII interface
library. Select MII so it gets built when that driver is selected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use better terminology for HW queues. No functional changes.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- this implementation of prefetch was tested on new and old hardware
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
- Add restriction for ESB2 to MTU size <=9216
- Removed FIFO errors which were not being used
- Fixed issues with loopback
- Power management change for saving state and config space
- WA to disable recieves and reset device on link loss. Reset needed to be done outside the interrupt context - modified existing tx_timeout_task
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
- Simplified by calling skb_fill_page_desc(), which is more efficient.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
The axnet_cs driver can support the AMB8110 PC Card, so add the id for it.
In the old pcmcia-cs config file, this card is listed with the comment "not
specific enough". The last entry in the axnet_ids has the same comment.
They are disabled, and for good reason as it was originally identified by
the MANFID, and that is shared with several cards that use both the
pcnet_cs driver and axnet_cs driver. I tried my AMB8110 with pcnet_cs, and
found that it works fine, and I cannot find a reason for either, except
that the old config file recommended axnet_cs.
Signed-off-by: Jesse Allen <the3dfxdude@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Don't just use cards with PCMCIA ID 0x0156, 0x0002. Make sure that the
vendor string is "Intersil" or "INTERSIL"
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
A recent patch attempted to enable more efficient memory usage by using
only 2kB descriptors for jumbo frames. The method used to implement this
has since been commented upon as "illegal" and in recent kernels even
causes a BUG when receiving ip fragments while using jumbo frames.
This patch simply goes back to the way things were. We expect some
complaints due to order 3 allocations failing to come back due to this
change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Remove Message Signaled Interrupt support (for 2.6.16).
MSI is inherently edge-triggered and that is incompatiable (without more
work) with NAPI.
In future, will replace with smarter lockless-IRQ handling like
tg3.c
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These messages end up polluting logs when things like NetworkManager or
wpa_supplicant are controlling the driver. They aren't really that
useful, and no other drivers output messages like this when the user
fiddles with encryption keys. Users can use iwconfig and other
wireless-tools methods to determine and change the current transmit key
if they wish to do so manually. Therefore, remove the messages.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- check that the device is up before it is enabled again;
- the descriptor ring indexes must be set to zero before
cp_init_hw() is issued. Add a nice comment to remember
that skb allocation failure is still not handled.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=5681
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
velocity_rx_refill() only replenishes the descriptor entries which
belong to the CPU. It works great in the Rx path but the driver must
ensure that all the descriptors are freed before velocity_rx_refill()
is used in velocity_change_mtu(). The patch resets the Rx descriptors
in velocity_free_rd_ring().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Some Sun parts don't have PCI_VENDOR_ID_SUN in the subsystem
vendor ID. So add another fallback test, which is the name
of the OBP firmware device tree node. If it's a Sun part we'll
get "network", else it will be named "ethernet".
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two bugs in the WoL implementation of sis900. The first causes
hangs on some system on driver load, the second causes troubles
when disabling WoL support. Both fixes are one liner and really
simple.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Daniele Venzano <venza@brownhat.org>
Zhu Yi