Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usb/otg-fsm.h and usb/composite.h are included together
then it results in the build warning [1].
Prevent that by defining VDBG locally.
Also get rid of MPC_LOC which doesn't seem to be used
by anyone.
[1] - warning fixed by this patch:
In file included from drivers/usb/dwc3/core.h:33,
from drivers/usb/dwc3/ep0.c:33:
include/linux/usb/otg-fsm.h:30:1: warning: "VDBG" redefined
In file included from drivers/usb/dwc3/ep0.c:31:
include/linux/usb/composite.h:615:1: warning: this is the location
of the previous definition
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix warning about tainted kernel because usb-otg-fsm has no license.
WARNING: with this patch usb-otg-fsm module can be loaded
but then the kernel will hang. Tested with a udoo quad board.
Cc: <stable@vger.kernel.org> #v4.1+
Signed-off-by: Oscar <oscar@naiandei.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Move the state_changed variable into struct otg_fsm
so that we can support multiple instances.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Adds HNP polling timer when transits to host state, the OTG status
request will be sent to peripheral after timeout, if host request flag
is set, it will switch to peripheral state, otherwise it will repeat HNP
polling every 1.5s and maintain the current session.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We should signal connect (pull up dp) after we have already
at peripheral mode, otherwise, the dp may be toggled due to
we reset controller or do disconnect during the initialization
for peripheral, then, the host may be confused during the
enumeration, eg, it finds the reset can't succeed, but the
device is still there, see below error message.
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: unable to enumerate USB device on port 1
Fixes: the issue existed when the otg fsm code was added.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since usb otg fsm implementation is not related to usb phy.
We move it from usb/phy/ to usb/common/, and rename it to
reflect its real meaning.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman