Inline the transport_off == 0 case into target_execute_cmd to simplify
the function for the remaining cases.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Existing lio_dump.py code expects this to be in place for /iscsi.
Revert for now to avoid userspace breakage in lio-utils
This reverts commit fd88a785f9ac5d6be437c528571ccd85cdf2d493.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Having all the unmap payload parsing in the backed is a bit ugly, but until
more drivers support it and we can find a good interface for all of them
that seems the way to go.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add spc_ops->execute_write_same() caller for ->execute_cmd() setup,
and update IBLOCK backends to use it.
(nab: add export of spc_get_write_same_sectors symbol)
(roland: Carry forward: Fix range calculation in WRITE SAME emulation
when num blocks == 0)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add spc_ops->execute_sync_cache() caller for ->execute_cmd() setup,
and update IBLOCK + FILEIO backends to use it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the execute_cmd method in struct se_subsystem_api, and always use the
one directly in struct se_cmd. To make life simpler for SBC virtual backends
a struct spc_ops that is passed to sbc_parse_cmd is added. For now it
only contains an execute_rw member, but more will follow with the subsequent
commits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the dead SCF_SE_ALLOW_EOO and SCF_DELAYED_CMD_FROM_SAM_ATTR
from se_cmd_flags_table.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
see https://bugzilla.redhat.com/show_bug.cgi?id=818855
Adds a parameter so read-only block devices may be registered as
LIO backstores.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These modules, along with other fabrics, should be loaded as-needed by
the LIO userspace tools.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Also remove the unused ref_task_lun field in struct se_tmr_req.
(nab: Add missing TASK_REASSIGN ref_lun vs. ref_cmd orig_fe_lun checks
in iscsit_tmr_task_reassign)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since "target: Drop se_device TCQ queue_depth usage from I/O path" we always
submit all commands (or back then, tasks) from __transport_execute_tasks.
That means the the execute list has lots its purpose, as we can simply
submit the commands that are restarted in transport_complete_task_attr
directly while we walk the list. In fact doing so also solves a race
in the way it currently walks to delayed_cmd_list as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes back the pSCSI backend to follow pre 3.6-queue code to
passthrough SPC-3 persistent reservations + SPC-2 legacy reservation
handling to the underlying LLD / physical hardware.
For folks who really need this for their own SPC-3 emulation logic, avoid
changing the functionality of this beyond what is exported for REPORT_LUNS
for existing code, and to avoid problems with SPC-3 PR/ALUA as INQUIRY
EVPD=0x83 emulation needs to be in place in order for this to work as
expected with spc_parse_cdb() code..
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The MAINTENANCE_[IN,OUT] CDB parsing required for generic ALUA emulation
needs to be in spc_parse_cdb() to function for virtual TYPE_DISK exports,
instead of in backend pscsi_parse_cdb() code used only for passthrough ops.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The virtual drivers don't need to clear cdb fields they never look at, so move
this code into the pscsi backend.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move the existing code in target_core_cdb.c into the files for the command
sets that the emulations implement.
(roland + nab: Squash patch: Fix range calculation in WRITE SAME emulation
when num blocks == 0s)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of trying to handle all SCSI command sets in one function
(transport_generic_cmd_sequencer) call out to the backend driver to perform
this functionality. For pSCSI a copy of the existing code is used, but for
all virtual backends we can use a new parse_sbc_cdb helper is used to
provide a simple SBC emulation.
For now this setups means a fair amount of duplication between pSCSI and the
SBC library, but patches later in this series will sort out that problem.
(nab: Fix up build failure in target_core_pscsi.c)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We don't need three flags to classifiy the CDB as we can check for a NULL S/G
list for a dataless command, and can infer from the absence of the data flag
that we deal with a control CDB. Also remove the _SG_IO from the data CDB
flag as all I/O is dont on S/G lists now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move all code not related to cdb parsing from transport_generic_cmd_sequencer
into target_setup_cmd_from_cdb.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When NUMBER OF LOGICAL BLOCKS is 0, WRITE SAME is supposed to write
all the blocks from the specified LBA through the end of the device.
However, dev->transport->get_blocks(dev) (perhaps confusingly) returns
the last valid LBA rather than the number of blocks, so the correct
number of blocks to write starting with lba is
dev->transport->get_blocks(dev) - lba + 1
(nab: Backport roland's for-3.6 patch to for-3.5)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- instead of (PTR_ERR(file) < 0) just use IS_ERR(file)
- return -EINVAL instead of EINVAL
- all other error returns in target_scsi3_emulate_pr_out() use
"goto out" -- get rid of the one remaining straight "return."
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a crash seen when large reads have their exchange
aborted by either timing out or being reset. Because the exchange
abort results in the seq pointer being set to NULL, because the
sequence is no longer valid, it must not be dereferenced. This
patch changes the function ft_get_task_tag to return ~0 if it is
unable to get the tag for this reason. Because the get_task_tag
interface provides no means of returning an error, this seems
like the best way to fix this issue at the moment.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use rcu_dereference_protected to tell rcu that the ft_lport_lock
is held during ft_lport_create. This resolved "suspicious RCU usage"
warnings when debugging options are turned on.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The error paths in target_emulate_set_target_port_groups() are all
essentially "rc = -EINVAL; goto out;" but the code at "out:" ignores
rc and always returns success. This means that even if eg explicit
ALUA is turned off, the initiator will always see a good SCSI status
for SET TARGET PORT GROUPS.
Fix this by returning rc as is intended. It appears this bug was
added by the following patch:
commit 05d1c7c0d0
Author: Andy Grover <agrover@redhat.com>
Date: Wed Jul 20 19:13:28 2011 +0000
target: Make all control CDBs scatter-gather
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an optional target_core_fabric_ops->put_session() caller
within the existing target_put_session() code path.
This is required by tcm_qla2xxx code in order to invoke it's own fabric
specific session shutdown handler using se_session->sess_kref.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Convert to use O_DSYNC for all cases at FILEIO backend creation time to
avoid the extra syncing of pure timestamp updates with legacy O_SYNC during
default operation as recommended by hch. Continue to do this independently of
Write Cache Enable (WCE) bit, as WCE=0 is currently the default for all backend
devices and enabled by user on per device basis via attrib/emulate_write_cache.
This patch drops the now unnecessary fd_buffered_io= token usage that was
originally signalling when to explictly disable O_SYNC at backend creation
time for buffered I/O operation. This can end up being dangerous for a number
of reasons during physical node failure, so go ahead and drop this option
for now when O_DSYNC is used as the default.
Also allow explict FUA WRITEs -> vfs_fsync_range() call to function in
fd_execute_cmd() independently of WCE bit setting.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
'int login_id' shadows 'static atomic_t login_id'.
Seen as compilation warning on x86-32.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull sbp-2 (firewire) target mode support from Nicholas Bellinger:
"The FireWire SBP-2 Target is a driver for using an IEEE-1394
connection as a SCSI transport. This module uses the SCSI Target
framework to expose LUNs to other machines attached to a FireWire bus,
in effect acting as a FireWire hard disk similar to FireWire Target
Disk mode on many Apple computers.
Also included are the two drivers/firewire/ patches required by
sbp-target to access fw_request fabric speed needed for mgt_agent
TCODE_WRITE_BLOCK_REQUEST ops, and exporting fw_card kref logic used
when creating/destroying active session references to individual
endpoints.
A credit goes to Chris in being able to get this code up and running
so quickly w/o any target core changes, and special thanks goes out to
Stefan Richter + Clemens Ladisch + Andy Grover for their help in
getting this driver ready for mainline. Also, one of Chris's goals
was to be able to connect sbp-target to a PowerPC based MacOS-X based
client, that he accomplished along the way in this obligatory
screenshot:
http://linux-iscsi.org/wiki/File:Linux-fireware-target-bootc-macosx.png
Great work Chris + linux-1394 team !!"
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'sbp-target-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
sbp-target: Initial merge of firewire/ieee-1394 target mode support
firewire: Move fw_card kref functions into linux/firewire.h
firewire: Add function to get speed from opaque struct fw_request
Pull scsi-target changes from Nicholas Bellinger:
"There has been lots of work in existing code in a number of areas this
past cycle. The major highlights have been:
* Removal of transport_do_task_sg_chain() from core + fabrics
(Roland)
* target-core: Removal of se_task abstraction from target-core and
enforce hw_max_sectors for pSCSI backends (hch)
* Re-factoring of iscsi-target tx immediate/response queues (agrover)
* Conversion of iscsi-target back to using target core memory
allocation logic (agrover)
We've had one last minute iscsi-target patch go into for-next to
address a nasty regression bug related to the target core allocation
logic conversion from agrover that is not included in friday's
linux-next build, but has been included in this series.
On the new fabric module code front for-3.5, here is a brief status
update for the three currently in flight this round:
* usb-gadget target driver:
Sebastian Siewior's driver for supporting usb-gadget target mode
operation. This will be going out as a separate PULL request from
target-pending/usb-target-merge with subsystem maintainer ACKs. There
is one minor target-core patch in this series required to function.
* sbp ieee-1394/firewire target driver:
Chris Boot's driver for supportting the Serial Block Protocol (SBP)
across IEEE-1394 Firewire hardware. This will be going out as a
separate PULL request from target-pending/sbp-target-merge with two
additional drivers/firewire/ patches w/ subsystem maintainer ACKs.
* qla2xxx LLD target mode infrastructure changes + tcm_qla2xxx:
The Qlogic >= 24xx series HW target mode LLD infrastructure patch-set
and tcm_qla2xxx fabric driver. Support for FC target mode using
qla2xxx LLD code has been officially submitted by Qlogic to James
below, and is currently outstanding but not yet merged into
scsi.git/for-next..
[PATCH 00/22] qla2xxx: Updates for scsi "misc" branch
http://www.spinics.net/lists/linux-scsi/msg59350.html
Note there are *zero* direct dependencies upon this for-next series
for the qla2xxx LLD target + tcm_qla2xxx patches submitted above, and
over the last days the target mode team has been tracking down an
tcm_qla2xxx specific active I/O shutdown bug that appears to now be
almost squashed for 3.5-rc-fixes."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (47 commits)
iscsi-target: Fix iov_count calculation bug in iscsit_allocate_iovecs
iscsi-target: remove dead code in iscsi_check_valuelist_for_support
target: Handle ATA_16 passthrough for pSCSI backend devices
target: Add MI_REPORT_TARGET_PGS ext. header + implict_trans_secs attribute
target: Fix MAINTENANCE_IN service action CDB checks to use lower 5 bits
target: add support for the WRITE_VERIFY command
target: make target_put_session void
target: cleanup transport_execute_tasks()
target: Remove max_sectors device attribute for modern se_task less code
target: lock => unlock typo in transport_lun_wait_for_tasks
target: Enforce hw_max_sectors for SCF_SCSI_DATA_SG_IO_CDB
target: remove the t_se_count field in struct se_cmd
target: remove the t_task_cdbs_ex_left field in struct se_cmd
target: remove the t_task_cdbs_left field in struct se_cmd
target: remove struct se_task
target: move the state and execute lists to the command
target: simplify command to task linkage
target: always allocate a single task
target: replace ->execute_task with ->execute_cmd
target: remove the task_sectors field in struct se_task
...
This patch fixes a bug in iscsit_allocate_iovecs() where iov_count was
incorrectly calculated using min(1UL, data_length / PAGE_SIZE) instead of
max(1UL, data_length / PAGE_SIZE), that ends up triggering an OOPs for
large block I/O when the SGL <-> iovec mapping exceeds the bogus iov_count
allocation size.
This is a regression introduced during the iscsi-target conversion back
to using core memory allocation here:
commit bfb79eac20
Author: Andy Grover <agrover@redhat.com>
Date: Tue Apr 3 15:51:29 2012 -0700
target/iscsi: Go back to core allocating data buffer for cmd
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Neither "acceptor_values" nor "proposer_values" can be NULL here when
scanning the value lists for incoming iSCSI login parameters such as
HeaderDigest=CRC32C,None.
Smatch complains because we are not allowed to pass NULL pointers to
strchr(). Also I removed a second later check for "!acceptor_values"
because it gets checked on the next line in the do while condition.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in the handling of FILEIO w/ underlying block_device
resize operations where the original fd_dev->fd_dev_size was incorrectly being
used in fd_get_blocks() for READ_CAPACITY response payloads.
This patch avoids using fd_dev->fd_dev_size for FILEIO devices with
an underlying block_device, and instead changes fd_get_blocks() to
get the sector count directly from i_size_read() as recommended by hch.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The cdrecord uses ATA_PASS_THROUGH_16 command while burning CDs
with a SATA CD-ROM. This patch adds support to it so that PSCSI
CD-ROM passthrough works with the cdrecord.
(nab: Add !passthrough check to prevent non pSCSI backends from ATA_16)
Signed-off-by: Cong Meng <mc@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for ALUA MI_REPORT_TARGET_PGS extended header
format defined within SPC-4. It changes target core ALUA emulation logic
within target_emulate_report_target_port_groups() to support both the
extended and original length only header formats.
It includes adding a new 'implict_trans_secs' attribute for each ALUA
target port group to control the value returned to the application client
for an recommended implict translation timeout in seconds. By default
this value is currently set to zero, and limited up to 255 by virtue of
using a single byte in the extended header format.
This value is used by target_emulate_report_target_port_groups() within
the extended header logic to set IMPLICIT TRANSITION TIME as defined by
spc4r30.
Cc: Hannes Reinecke <hare@suse.de>
Cc: Rob Evers <revers@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the MAINTENANCE_IN service action type checks to only
look at the proper lower 5 bits of cdb byte 1. This addresses the case
where MI_REPORT_TARGET_PGS w/ extended header using the upper three bits of
cdb byte 1 was not processed correctly in transport_generic_cmd_sequencer,
as well as the three cases for standby, unavailable, and transition ALUA
primary access state checks.
Also add MAINTENANCE_IN to the excluded list in transport_generic_prepare_cdb()
to prevent the PARAMETER DATA FORMAT bits from being cleared.
Cc: Hannes Reinecke <hare@suse.de>
Cc: Rob Evers <revers@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some legacy OS use WRITE_VERIFY on hard disks.
Signed-off-by: Bernhard Kohl <bernhard.kohl@gmx.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug in a special case for target core SPC-2 RELEASE
logic where the same physical client (eg: iSCSI InitiatorName) with
differing iSCSI session identifiers (ISID) is allowed to incorrectly release
the same client's SPC-2 reservation from the non reservation holding path.
Note this bug is specific to iscsi-target w/ SPC-2 reservations, and
with the default enforce_pr_isids=1 device attr setting in target-core
controls if a InitiatorName + different ISID reservations are handled
the same as a single iSCSI client entity.
Signed-off-by: Bernhard Kohl <bernhard.kohl@gmx.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The function is effectively void and doesn't need any goto logic.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes some potentially problematic legacy code within
core_clear_initiator_node_from_tpg() that was originally intended to
release left over se_lun_acl setup during dynamic NodeACL+MappedLUN
generate when running with TPG demo-mode operation.
Since we now only ever expect to allocate and release se_lun_acl from
within target_core_fabric_configfs.c:target_fabric_make_mappedlun() and
target_fabric_drop_mappedlun() context respectively, this code for
demo-mode release is incorrect and needs to be removed.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The FireWire SBP-2 Target is a driver for using an IEEE-1394 connection
as a SCSI transport. This module uses the SCSI Target framework to
expose LUNs to other machines attached to a FireWire bus, in effect
acting as a FireWire hard disk similar to FireWire Target Disk mode
on many Apple computers.
This commit contains the squashed pull from Chris Boot's SBP-2-Target:
https://github.com/bootc/Linux-SBP-2-Target.git patch-v3
firewire-sbp-target: Add sbp_base.h header
firewire-sbp-target: Add sbp_configfs.c
firewire-sbp-target: Add sbp_fabric.{c,h}
firewire-sbp-target: Add sbp_management_agent.{c,h}
firewire-sbp-target: Add sbp_login.{c,h}
firewire-sbp-target: Add sbp_target_agent.{c,h}
firewire-sbp-target: Add sbp_scsi_cmnd.{c,h}
firewire-sbp-target: Add to target Kconfig and Makefile
Also add bootc's entry to the MAINTAINERS file. Great work Chris !!
Signed-off-by: Chris Boot <bootc@bootc.net>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes the original usage of dev_attr->max_sectors in favor of
dev_attr->hw_max_sectors that is now being enforced by target core from
within transport_generic_cmd_sequencer() for SCF_SCSI_DATA_SG_IO_CDB ops.
After the recent se_task removal patches from hch, this value for IBLOCK
backends being set via configfs by userspace from an saved max_sectors
value that is turning out to be problematic, so it makes sense to go ahead
and remove this now legacy attribute all-together.
This patch also continues to make se_dev_set_default_attribs() do
(sectors / block_size) alignment for what actually get used by
target_core_mod to be safe here, following the same alignment currently
used by fabric_max_sectors.
Reported-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target_stop_cmd() returns with the lock held and IRQs disabled. The
intent was to unlock here. This bug was originally added with:
commit cf572a9627
Author: Christoph Hellwig <hch@infradead.org>
Date: Tue Apr 24 00:25:05 2012 -0400
target: move the state and execute lists to the command
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of depending upon a max_sectors value that may be set via
configfs based upon original HW queue limitations, go ahead and convert to using
the hw_max_sectors reported by the backend device in order to determine when
to reject an I/O's who's sector count exceeds what is supported by the backend
with a single se_cmd descriptor.
It addresses a potential case where se_dev_attrib.max_sectors for IBLOCK
backends has already been set via queue_max_sectors() to something small
like max_sectors=32 (LVM, DRBD may do this), resulting typically sized
SCF_SCSI_DATA_SG_IO_CDB to be incorrectly rejected with invalid_cdb_field
in transport_generic_cmd_sequencer().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that tasks are gone we are guaranteed to only get a single completion
per command, and thus don't need this counter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that tasks are gone we are guaranteed to only get a single completion
per command, and thus don't need this counter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that tasks are gone we are guaranteed to only get a single completion
per command, and thus don't need this counter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We can use struct se_cmd for everything it did. Make sure to pass the S/G
list and data direction to the execution function to ease adding back BIDI
support later on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we only have a single task per command we can use a direct pointer
to it instead of list.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simply transport_generic_new_cmd to only allocate a single task. For normal
unidirection commands nothing changes except that the code is a lot simpler
now. Any BIDI support that used to work will stop now for the next few
patches at least.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make CDB emulation work on commands instead of tasks again as a preparation
of removing tasks completely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the task_sectors field that isn't used anywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we don't split commands the size field in the task is always
equivalent to the one in the CDB, even in cases where we have two tasks
due to a BIDI transfer. Just refer the the size in the command instead
of duplicating it in the task.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we don't split commands the lba field in the task is always
equivalent to the one in the CDB, even in cases where we have two tasks
due to a BIDI transfer. Just refer the the lba in the command instead
of duplicating it in the task.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that tasks are always the same size as the command there is no need
to rewrite a CDB in common code. Notw that we keep the separately allocated
CDB in the pscsi and stgt backends for now, to easy reintroducing any
command splitting local to these backends if nessecary.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The SCSI MMC GET_EVENT_STATUS_NOTIFICATION command can be used to find
out about media change, among other things. This patch adds it to the
command sequencer so that PSCSI CD-ROM passthrough works with modern
Linux guests that issue this command.
Tested-by: Cong Meng <mengcong@cn.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We can use kcalloc() here instead of kzalloc(). It's better style and
it has overflow checking built in.
Also -ENOMEM is the correct error code for allocation errors. -1 means
-EPERM. None of the callers preserve the error codes so it doesn't
matter except as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We originally changed iscsi to allocate its own buffers just as an
intermediate step to clean up some core buffer allocation mechanisms. Now
we can put it back.
Also had to change allocate_iovecs to use data_length instead of
t_data_nents because iovecs are now allocated before the data buffer, thus
t_data_nents is not yet initialized.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It appears iscsi is the only one to call this in its cmd submit path, but
it appears to be applicable to all fabrics, and should always be called.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Rename iscsit_build_pdu_and_seq_list to iscsit_do_build_pdu_and_seq_lists
Rename iscsit_do_build_list to iscsit_build_pdu_and_seq_lists
Move code from iscsit_decide_list_to_build into _seq_pdu_list.c, seems
a better fit.
Also update some comments in pdu/seq code for correctness and whitespace.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Redundant, just use iscsi_cmd->se_cmd.data_length once se_cmd is
initialized, or hdr->data_length before then.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
if we can get calls to init_se_cmd, get_sess_cmd, lookup_cmd_lun,
core_alua_check_nonop_delay, and handle_cdb_direct next to each other,
then we can just call target_submit_cmd. This is a step towards that
goal.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Trying to move a bunch of stuff around so iscsi can use target_submit_cmd
someday, and so stuff needs to be in that function directly instead of
hidden, so it can be reordered etc.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch renames a horribly misnamed function that no longer allocate
tasks to something more descriptive for it's modern use in target core.
(nab: Fix up ib_srpt to use this as well ahead of a target_submit_cmd
conversion)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch includes the handful of squashed patches for target/iscsi from
Andy's original series into lio-core/master code:
*) Make iscsit_add_reject static
*) Remove unused data_offset_end from iscsi_datain_req
*) Remove "#if 0" stubs
*) Rename iscsi_datain_req to cmd_datain_node
*) Cleanups for built_r2ts_for_cmd()
*) Cleanups for Cleanup build_sendtargets_response()
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Immediate queue:
Consolidate down to one switch statement by moving send_tx_data and stuff
from second switch into the first switch, or the functions the first switch
calls.
Response queue:
Do not lock istate_lock except directly around i_state modifications.
Put entire ISTATE_SEND_DATAIN path within first switch statement, in prep
for further refactoring.
All other cases set use_misc = 1 and will not be using sendpage, so just
use send_tx_data for these and set use_misc param to 1.
map_sg, sent_status, use_misc, and se_cmd vars no longer needed.
Then put immediate and response handling in separate functions in order
to get iscsi_target_tx_thread down to where it fits on a page.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When processing immediate queue, we're switching on a local variable
so it's not necessary to lock around it. However, we are modifying
cmd->i_state in two spots, so lock around those parts only.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
*) Use decoded cmd->immediate_cmd for conditional instead of
re-examining hdr->opcode
*) Make iscist_dataout_post_crc_passed more legible
*) use max() to reduce code in build_r2ts_for_cmd()
*) Remove CONFIG_SMP and if 0 ifdefs
*) Replace if/goto with a while loop
*) Remove unused conn->tx_immediate_queue and tx_response_queue
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The name change makes it clear this list_head is so the cmd can be an
item in the connection's conn_cmd_list.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that all fabrics are converted over to using se_cmd->t_data_sg
directly, we can drop the task sg chaining support. With the modern
memory allocation in target core, task sg chaining is needless
overhead -- we would split up the main cmd sglist into pieces, and
then splice those pieces back together instead of just using the
original list directly.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With the modern target core, se_cmd->t_data_sg already points to a
sglist that covers the whole command. So task_sg chaining is needless
overhead and obfuscation -- instead of splicing the split up task
sglists back into one list, we can just use the original list directly.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
From hch:
The high-performance backends (iblock and rd) support tasks of unlimited
size. With that there is no reason to keep a complex infrastructure for
splitting up commands in place. Stop doing so and only submit a single
task per data direction. Once this is in place we can slowly remove fields
from the task that duplicate things in the command, or move other fields
into the command.
From nab:
The benefit to IBLOCK performance by removing the additional
fast-path allocation overhead + SGL mapping to se_task->task_sg[] is now
greater than transparently supporting an received CDB I/O length that
exceeds what is allowed by backend pSCSI LLD hardware max_sectors, that
was originally supported for all backend export cases.
This change may effect some users of pSCSI users on legacy hardware, but
I think most folks are now using TYPE_DISK struct scsi_device export
with IBLOCK. The only other place where this may can issues that cannot
be resolved with IBLOCK TYPE_DISK is using TYPE_ROM, TYPE_TAPE or other
pSCSI non TYPE_DISK export with an SCSI LLDs using a smaller
max_sectors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The ramdisk backend has not inherent limitations for handling requests,
so don't artificially limits the transfer size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove various leftovers of the old direct/indirect split, as well as the
unused rd_request structure and a couple unused defines and fields.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The UASP protocol does not inform the target device upfront how much
data it should expect so we have to learn in from the CDB. So in order
to handle this case, add a TARGET_SCF_UNKNOWN_SIZE to target_submit_cmd()
and perform an explictly assignment for se_cmd->data_length from the
extracted CDB size in transport_generic_cmd_sequencer().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This was used at one time as a hack by FILEIO backend registration to
allow a struct block_device that was claimed with blkdev_get (by a local
filesystem mount for example) to be exported as read-only (SCSI WP=1).
Since FILEIO backend registration will no longer attempt to obtain
exclusive access to an underlying struct block_device here, this flag is
now obsolete.
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Avoid freeing a registered tpg structure if an alloc_workqueue call
fails. This fixes a bug where the failure was leaking memory associated
with se_portal_group setup during the original core_tpg_register() call.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add abort flag and use it to terminate processing when an exchange
is timed out or is reset. The abort flag is used in place of the
transport_generic_free_cmd function call in the reset and timeout
cases, because calling that function in that context would free
memory that was in use. The aborted flag allows the lifetime to
be managed in a more normal way, while truncating the processing.
This change eliminates a source of memory corruption which
manifested in a variety of ugly ways.
(nab: Drop unused struct fc_exch *ep in ft_recv_seq)
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"This contains the usual set of updates and bugfixes to target-core +
existing fabric module code, along with a handful of the patches
destined for v3.3 stable.
It also contains the necessary target-core infrastructure pieces
required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
Channel fabric module currently queued in target-pending/for-next-merge,
and coming for round 2.
The highlights for this series include:
- Add target_submit_tmr() helper function for fabric task management
(andy)
- Convert tcm_fc to use target_submit_tmr() (andy)
- Replace target core various cmd flags with a transport state (hch)
- Convert loopback to use workqueue submission (hch)
- Convert target core to use array_zalloc for tpg_lun_list (joern)
- Convert target core to use array_zalloc for device_list (joern)
- Add target core support for TMR_ABORT_TASK (nab)
- Add target core se_sess->sess_kref + get/put helpers (nab)
- Add target core se_node_acl->acl_kref for ->acl_free_comp usage
(nab)
- Convert iscsi-target to use target_put_session + sess_kref (nab)
- Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
- Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
exception (nab)
- Fix target core up handling of short INQUIRY buffers (roland)
- Untangle target-core front-end and back-end meanings of max_sectors
attribute (roland)
- Set loopback residual field for SCSI commands (roland)
- Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
emulation (roland)
Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
loopback: Fix transport_generic_allocate_tasks error handling
iscsi-target: remove improper externs
iscsi-target: Remove unused variables in iscsi_target_parameters.c
target: remove obvious warnings
target: Use array_zalloc for device_list
target: Use array_zalloc for tpg_lun_list
target: Fix sense code for unsupported SERVICE ACTION IN
target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
target: Bump core version to v4.1.0-rc2-ml + fabric versions
tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
target: Drop unused legacy target_core_fabric_ops API callers
iscsi-target: Convert to use target_put_session + sess_kref
target: Convert se_node_acl->acl_group removal to use ->acl_kref
target: Add se_node_acl->acl_kref for ->acl_free_comp usage
target: Add se_node_acl->acl_free_comp for NodeACL release path
target: Add se_sess->sess_kref + get/put helpers
target: Convert session_lock to irqsave
target: Fix typo in drivers/target
iscsi-target: Fix dynamic -> explict NodeACL pointer reference
...
Pull security subsystem updates for 3.4 from James Morris:
"The main addition here is the new Yama security module from Kees Cook,
which was discussed at the Linux Security Summit last year. Its
purpose is to collect miscellaneous DAC security enhancements in one
place. This also marks a departure in policy for LSM modules, which
were previously limited to being standalone access control systems.
Chromium OS is using Yama, and I believe there are plans for Ubuntu,
at least.
This patchset also includes maintenance updates for AppArmor, TOMOYO
and others."
Fix trivial conflict in <net/sock.h> due to the jumo_label->static_key
rename.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (38 commits)
AppArmor: Fix location of const qualifier on generated string tables
TOMOYO: Return error if fails to delete a domain
AppArmor: add const qualifiers to string arrays
AppArmor: Add ability to load extended policy
TOMOYO: Return appropriate value to poll().
AppArmor: Move path failure information into aa_get_name and rename
AppArmor: Update dfa matching routines.
AppArmor: Minor cleanup of d_namespace_path to consolidate error handling
AppArmor: Retrieve the dentry_path for error reporting when path lookup fails
AppArmor: Add const qualifiers to generated string tables
AppArmor: Fix oops in policy unpack auditing
AppArmor: Fix error returned when a path lookup is disconnected
KEYS: testing wrong bit for KEY_FLAG_REVOKED
TOMOYO: Fix mount flags checking order.
security: fix ima kconfig warning
AppArmor: Fix the error case for chroot relative path name lookup
AppArmor: fix mapping of META_READ to audit and quiet flags
AppArmor: Fix underflow in xindex calculation
AppArmor: Fix dropping of allowed operations that are force audited
AppArmor: Add mising end of structure test to caps unpacking
...
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Pull RCU changes for v3.4 from Ingo Molnar. The major features of this
series are:
- making RCU more aggressive about entering dyntick-idle mode in order
to improve energy efficiency
- converting a few more call_rcu()s to kfree_rcu()s
- applying a number of rcutree fixes and cleanups to rcutiny
- removing CONFIG_SMP #ifdefs from treercu
- allowing RCU CPU stall times to be set via sysfs
- adding CPU-stall capability to rcutorture
- adding more RCU-abuse diagnostics
- updating documentation
- fixing yet more issues located by the still-ongoing top-to-bottom
inspection of RCU, this time with a special focus on the CPU-hotplug
code path.
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (48 commits)
rcu: Stop spurious warnings from synchronize_sched_expedited
rcu: Hold off RCU_FAST_NO_HZ after timer posted
rcu: Eliminate softirq-mediated RCU_FAST_NO_HZ idle-entry loop
rcu: Add RCU_NONIDLE() for idle-loop RCU read-side critical sections
rcu: Allow nesting of rcu_idle_enter() and rcu_idle_exit()
rcu: Remove redundant check for rcu_head misalignment
PTR_ERR should be called before its argument is cleared.
rcu: Convert WARN_ON_ONCE() in rcu_lock_acquire() to lockdep
rcu: Trace only after NULL-pointer check
rcu: Call out dangers of expedited RCU primitives
rcu: Rework detection of use of RCU by offline CPUs
lockdep: Add CPU-idle/offline warning to lockdep-RCU splat
rcu: No interrupt disabling for rcu_prepare_for_idle()
rcu: Move synchronize_sched_expedited() to rcutree.c
rcu: Check for illegal use of RCU from offlined CPUs
rcu: Update stall-warning documentation
rcu: Add CPU-stall capability to rcutorture
rcu: Make documentation give more realistic rcutorture duration
rcutorture: Permit holding off CPU-hotplug operations during boot
rcu: Print scheduling-clock information on RCU CPU stall-warning messages
...
This patch addresses a tcm_loop bug with transport_generic_allocate_tasks()
return checking in tcm_loop_submission_work() where other non zero return
codes (including -EBUSY for reservation conflicts) are incorrectly falling
through to transport_generic_map_mem_to_cmd() -> transport_handle_cdb_direct().
This bug was introduced into target-pending/for-next-merge with the following
for-3.4 commit:
commit 16786454ac
Author: Christoph Hellwig <hch@infradead.org>
Date: Thu Feb 2 17:04:42 2012 -0500
tcm_loop: switch to using transport_handle_cdb_direct
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These externs aren't needed and Sparse complains about them.
drivers/target/iscsi/iscsi_target_nodeattrib.c:52:12: warning:
function 'iscsit_na_dataout_timeout' with external linkage has
definition
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
local_right_val was an obvious case, tmp_ptr is also write-only, but
evades the compiler by being passed to simple_strtoul as char **endp.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Get rid of a bunch of write-only variables. In a number of cases I
suspect actual bugs to be present, so I left all of those for a second
look.
(nab: fix lio-core patch fuzz)
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Turns an order-8 allocation into slab-sized ones, thereby preventing
allocation failures with memory fragmentation.
This likely saves memory as well, as the slab allocator can pack objects
more tightly than the buddy allocator.
(nab: Fix lio-core patch fuzz)
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Turns an order-10 allocation into slab-sized ones, thereby preventing
allocation failures with memory fragmentation.
This likely saves memory as well, as the slab allocator can pack objects
more tightly than the buddy allocator.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If we don't handle a given service action, we're supposed to return
INVALID FIELD IN CDB, since we do handle the SERVICE ACTION IN opcode.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the hack that has READ CAPACITY(10) return 0xFFFFFFFF as the
number of sectors when thin provisioning is enabled. This is supposed
to trigger the initiator to use READ CAPACITY(16) in this case so that
it finds out about thin provisioning. But an initiator that cares about
thin provisioning is going to ask anyway, and an initiator that doesn't
know about READ CAPACITY(16) is going to get the wrong capacity. So
just have READ CAPACITY(10) return the size it's supposed to.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a iscsi-target specific bug related to reservation conflict
handling in iscsit_handle_scsi_cmd() that has been causing reservation conflicts
to complete and not fail as expected due to incorrect errno checking. The problem
occured with the change to return -EBUSY from transport_generic_cmd_sequencer() ->
transport_generic_allocate_tasks() failures, that broke iscsit_handle_scsi_cmd()
checking for -EINVAL in order to invoke a non GOOD status response.
This was manifesting itself as data corruption with legacy SPC-2 reservations,
but also effects iscsi-target LUNs with SPC-3 persistent reservations.
This bug was originally introduced in lio-core commit:
commit 03e98c9eb9
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Fri Nov 4 02:36:16 2011 -0700
target: Address legacy PYX_TRANSPORT_* return code breakage
Reported-by: Martin Svec <martin.svec@zoner.cz>
Cc: Martin Svec <martin.svec@zoner.cz>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug with target_check_scsi2_reservation_conflict()
return checking in target_scsi2_reservation_[reserve,release]() that was
preventing CRH=1 operation from silently succeeding in the two special
cases defined by SPC-3, and not failing with reservation conflict status
when dealing with legacy RESERVE/RELEASE + active SPC-3 PR logic.
Also explictly set cmd->scsi_status = SAM_STAT_RESERVATION_CONFLICT during
the early non reservation holder failure from pr_ops->t10_seq_non_holder()
check in transport_generic_cmd_sequencer() for fabrics that already expect
it to be set.
This bug was originally introduced in mainline commit:
commit eacac00ce5
Author: Christoph Hellwig <hch@infradead.org>
Date: Thu Nov 3 17:50:40 2011 -0400
target: split core_scsi2_emulate_crh
Reported-by: Martin Svec <martin.svec@zoner.cz>
Cc: Martin Svec <martin.svec@zoner.cz>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Bump core version to v4.1.0-rc2-ml, and for versions from the
following mainline fabric modules:
loopback: v2.1-rc2
tcm_fc: v0.4
iscsi-target: v4.1.0-rc2
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in tcm_fc where fc_exch memory from fc_exch_mgr->ep_pool
is currently being leaked by ft_send_resp_status() usage. Following current
code in ft_queue_status() response path, using lport->tt.seq_send() needs to be
followed by a lport->tt.exch_done() in order to release fc_exch memory back into
libfc_em kmem_cache.
ft_send_resp_status() code is currently used in pre submit se_cmd ft_send_work()
error exceptions, TM request setup exceptions, and main TM response callback
path in ft_queue_tm_resp(). This bugfix addresses the leak in these cases.
Cc: Mark D Rustad <mark.d.rustad@intel.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops the following unused legacy API callers from target_core_fabric.h:
*) TFO->fall_back_to_erl0()
*) TFO->stop_session()
*) TFO->sess_logged_in()
*) TFO->is_state_remove()
This patch also removes the stub usage in loopback, tcm_fc, iscsi_target,
and ib_srpt fabric modules.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts iscsi-target session code to use se_sess->sess_kref
counting for iscsi session shutdown. The following cases include:
*) last iscsit_close_connection() shutdown path to invoke close session
*) iscsit_logout_post_handler_closesession() for explict logout
*) iscsit_free_session() caller for explict shutdown
It also moves iscsit_stop_session() call from lio_tpg_close_session()
into lio_tpg_shutdown_session() TFO callbacks to invoke an explict
shutdown, and also changes iscsi_check_for_session_reinstatement()
login code to use se_sess->sess_kref.
(v2: Make iscsit_handle_time2retain_timeout() use target_put_session)
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts core_tpg_del_initiator_node_acl() shutdown from configfs
context to use se_node_acl->acl_kref and ->acl_free_comp in order to wait for
outstanding fabric callbacks to complete via transport_deregister_session()
callbacks before waking ->acl_free_comp from the last ->acl_kref put.
It also changes core_tpg_del_initiator_node_acl() to setup a local sess_list
with target_get_session() + acl->acl_stop = 1 for active sessions that will
be shutdown, and changes transport_deregister_session_configfs() to check
for ->acl_stop usage.
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds se_node_acl->acl_kref for use with ->acl_free_comp
during explict se_node_acl release. It adds kref_init() during
se_node_acl setup, kref_get() during __transport_register_session()
-> target_put_nacl() with existing transport_deregister_session()
fabric callback usage.
It also moves transport_free_session() to release *se_sess memory
after target_put_nacl() execution in transport_deregister_session()
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add se_node_acl->acl_free_comp for NodeACL release path to wait for outstanding
fabric session shutdown to complete in transport_deregister_session() before
finishing NodeACL release from configfs process context.
Also make transport_deregister_session() clear the comp_nacl bit
to skip se_node_acl->acl_free_comp completion for dynamically generated
NodeACL during fabric session shutdown.
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds basic se_session->sess_kref and get/put helpers for fabric
session reference counting. It sets the initial kref in transport_init_session()
and adds a target_release_session() callback to invoke TFO->close_session()
for final session shutdown.
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Correct spelling "exeeds" to "exceeds" in iscsi/iscsi_target_nego.c
Correct spelling "diabled" to "disabled" in target_core_configfs.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a free after use in lio_target_make_nodeacl() where
iscsi_node_acl was referenced from the original se_nacl_new allocation,
instead of from core_tpg_add_initiator_node_acl() in the case of dynamic
-> explict NodeACL conversion.
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch allows target_submit_tmr() to pass gfp_t for se_cmd->se_tmr_req
allocation, and also set up se_cmd->se_tmr_req->ref_task_tag for passed
tag with TMR_ABORT_TASK.
Also update tcm_fc(fcoe) parameter usgae and add ref_task_tag FIXME
for TMR_ABORT_TASK usage,
Cc: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to handle incoming target_submit_tmr() callers using interrupt
context, use system_wq process context for transport_lookup_tmr_lun()
failures to return TMR_LUN_DOES_NOT_EXIST status for fabric TM response.
Cc: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes ft_send_tm() handle target_submit_tmr() allocation failures
via an ft_send_resp_code_and_free() w/ FCP_TMF_FAILED status.
Cc: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes target_submit_tmr() se_tmr_req allocation occur before
target_get_sess_cmd(), and changes target_submit_tmr() to return a failure
w/ non zero status to the fabric caller upon core_tmr_alloc_req() failure.
Cc: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target_submit_tmr() LUN lookup failures to set response
status TMR_LUN_DOES_NOT_EXIST and invoke TFO->queue_tm_rsp(), instead of
sending CHECK_CONDITION status that can cause problems with Linux FCoE
clients.
Tested with tcm_fc ports and explict LUN_RESET lookup failures.
Cc: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make iscsit_alloc_buffs() failure case for page_alloc_failed use correct
__free_page() SGL pointer, and return -ENOMEM for iscsit_allocate_iovecs
failure to push se_cmd->t_mem_sg release into iscsit_release_cmd()
callback during iscsit_add_reject_from_cmd() connection reset.
Also drop cmd->t_mem_sg = NULL assignment from page_alloc_failed
failure case.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The old code did (MSB << 8) & 0xff, which always evaluates to 0. Just use
get_unaligned_be16() so we don't have to worry about whether our open-coded
version is correct or not.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
cdb_offset is always equal to offset - 8, so remove that one. More
importantly, the existing code only worked correct if
se_cmd->data_length is a multiple of 8. Pass in a length of, say, 9 and
we will happily overwrite 7 bytes of "unallocated" memory.
Now, afaics this bug is currently harmless, as allocations will
implicitly be padded to multiples of 8 bytes. But depending on such a
fact wouldn't qualify as sound engineering practice.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
transport_kmap_data_sg can return NULL. I never saw this trigger, but
returning -ENOMEM seems better than a crash. Also removes a pointless
case while at it.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix possible NULL pointer dereference in target_report_luns failure path.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the target core signals an over- or under-run, tcm_loop should call
scsi_set_resid() to tell the SCSI midlayer about the residual data length.
The difference can be seen by doing something like
strace -eioctl sg_raw -r 1024 /dev/sda 8 0 0 0 1 0 > /dev/null
and looking at the "resid=" part of the SG_IO ioctl -- after this patch,
the field is correctly reported as 512.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
se_dev_attrib.max_sectors currently has two independent meanings:
- It is reported in the block limits VPD page as the maximum transfer
length, ie the largest IO that the front-end (fabric) can handle.
Also the target core doesn't enforce this maximum transfer length.
- It is used to hold the size of the largest IO that the back-end can
handle, so we know when to split SCSI commands into multiple tasks.
Fix this by adding a new se_dev_attrib.fabric_max_sectors to hold the
maximum transfer length, and checking incoming IOs against that limit.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SPC-4 says about the WBUS16 and SYNC bits:
The meanings of these fields are specific to SPI-5 (see 6.4.3).
For SCSI transport protocols other than the SCSI Parallel
Interface, these fields are reserved.
We don't have a SPI fabric module, so we should never set these bits.
(The comment was misleading, since it only mentioned Sync but the
actual code set WBUS16 too).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Current code sets the peripheral device type to 0x3f == "not present
unknown" for virtual LUN 0 for standard INQUIRY commands, but leaves it
as 0 == "connected direct access block" for VPD INQUIRY commands. This
is just because the check for LUN 0 only happens in some code paths.
Make our peripheral device type consistent by moving the LUN 0 check
into the common emulate_inquiry() code.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the initiator sends us an INQUIRY command with an allocation length
that's shorter than what we want to return, we're simply supposed to
truncate our response and return what the initiator gave us space for,
without signaling any error. Current target code has various tests that
don't fill out the full response if the buffer is too short and
sometimes return errors incorrectly.
Fix this up by allocating a bounce buffer for INQUIRY responses if we
need to, ie if we have cmd->data_length too small as well as
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC set in cmd->se_cmd_flags -- for most
fabrics, we always allocate at least a full page, but for tcm_loop we
may have a small buffer coming directly from the SCSI stack.
This lets us delete a lot of cmd->data_length checking, and also makes
our INQUIRY handling correct per SPC in a lot more cases.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds initial support for TMR_ABORT_TASK ops for se_cmd
descriptors using se_sess->sess_cmd_list and se_cmd->cmd_kref counting.
It will perform an explict abort for all outstanding se_cmd ops based
upon tmr->ref_task_tag that have not been set CMD_T_COMPLETE.
It will cancel se_cmd->work and wait for backing I/O to complete before
attempting to send SAM_STAT_TASK_ABORTED and perform
target_put_sess_cmd() to release the referenced descriptor.
It also adds a CMD_T_ABORTED check into transport_complete_task() to
catch the completion from backend I/O that has been aborted, and
updates transport_wait_for_tasks() to allow CMD_T_ABORTED usage with
core_tmr_abort_task() context.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target_release_cmd_kref() to make TFO->release_cmd()
call when list_empty(&se_cmd->se_cmd_list) is TRUE. This is required
for TMR_ABORT_TASK operation where the referenced tag descriptor may
have already been pulled of the session command list.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When TARGET_SCF_ACK_KREF is in use with target_submit_cmd() for
setting the extra acknowledgement reference to se_cmd->cmd_kref,
go ahead and set SCF_ACK_KREF in order to be used later by
abort task.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
transport_generic_request_failure() is a wrapper around calling
transport_send_check_condition_and_sense() that is required once
an se_cmd->cmd_kref has been obtained via target_submit_cmd() ->
target_get_sess_cmd().
tcm_qla2xxx currently requires this, and since it's necessary for
other callers using target_submit_cmd() make it exportable now.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This code isn't broken per se, but it's scary to look at! It looks like
in the t_data_nents==1 case we're doing both a kunmap and a vunmap,
what's saving us is that t_data_vmap in this case is 0, so vunmap
doesn't do anything.
Return after kunmap, so the handling of the three cases does not overlap.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we use a workqueue for I/O submission there is no need to use
transport_generic_handle_cdb_map any more.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Apply the qla2xxx model of submitting all commands from a workqueue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This function makes little sense as a separate abstraction as it's deeply
interwinded with the control flow of its only caller. Merged it into
tcm_loop_queuecommand after factoring out a helper to convert the task
attribute representation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Change ft_send_tm() make use of the new target_submit_tmr helper
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Similar to target_submit_cmd, this function lets fabrics call one function
(albeit with a lot of parameters) instead of 3 or more.
(nab: Add missing return for transport_lookup_tmr_lun failure)
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
transport_generic_free_cmd will end up calling ft_sess_put, so it should
work just the same.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Don't see a reason to differentiate, so drop the fabric specific
switch statement in ft_send_tm() ahead of conversion to use
target_submit_tmr().
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
No dependencies on rest of code, let's get tm_func set asap.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Change the test for if a cmd is a tmr request to checking if
SCF_SCSI_TMR_CDB (a new flag) is set in cmd->se_cmd_flags.
Also remove se_tmr_req_cache usage in favor of kzalloc usage,
and make core_tmr_alloc_req() return int + setup se_cmd->se_tmr_req
directly and fix up various fabric module usages
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's used only for debug output. Debug output may want to make use of
fcp->fc_cdb directly.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Check fc_tm_flags early and call ft_send_tm() right away. Don't need to
set local vars for tm case.
data_len local var now unneeded, remove.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This allows us to use scsilun_to_int without an ugly cast.
Fix up places that use scsilun_to_int on fcp->fc_lun accordingly.
In fc target, this leaves ft_cmd.lun unused, so remove it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of
static struct list_head foo;
static struct mutex bar;
...
INIT_LIST_HEAD(&foo);
mutex_init(&bar);
just do
static LIST_HEAD(foo);
static DEFINE_MUTEX(bar);
Also remove some superfluous struct list_head and spinlock_t
initialization calls where the variables are already defined using
macros that initialize them.
This saves a decent amount of compiled code too:
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-178 (-178)
function old new delta
target_core_init_configfs 898 850 -48
core_scsi3_emulate_pro_preempt 1742 1683 -59
iscsi_thread_set_init 159 88 -71
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is no real limit for task sizes in the iblock driver given that we
can chain bios. Increase the maximum size to UINT_MAX, and change the
code to submit bios in a smaller batch size to avoid deadlocks when
having more bios in flight than the pool supports. Also increase the
pool size to always allow multiple tasks to be in flight.
I also had to change the task refcounting to include one reference for
the submission task, which is a standard practice in this kind of code
in Linux (e.g. XFS I/O submission). This was wrong before, but couldn't
be hit easily.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is no reason to allocate a struct just to store the host number for
a debug printk in the detach path. I've simply removed the verbose
debugging given that the calling code thinks the number passed in is
something different from a host ID anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is no reason to have a flag telling if a command is on the per-lun list,
we can simply do a list_empty check before removing it as long as we're careful
to always use list_del_init.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Replace various atomic_ts used as flags in struct se_cmd with a single
transport_state bitmap that requires t_state_lock to be held for modifications.
In the target core that assumption generally is true, but some recently added
code in the SRP target had to grow new lock calls. I can't say I like the way
how it messes with the command state directly, but let's leave that for later.
(Re-add missing ib_srpt.c changes that nab dropped..)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The call_rcu() in ft_tport_delete() invokes ft_tport_rcu_free(),
which just does a kfree(). So convert the call_rcu() to kfree_rcu(),
allowing ft_tport_rcu_free() to be eliminated.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: linux-scsi@vger.kernel.org
Cc: target-devel@vger.kernel.org
This patch fixes a bug in target-core where unsupported WRITE_SAME ops
from a target_check_write_same_discard() failure was incorrectly
returning CHECK_CONDITION w/ TCM_INVALID_CDB_FIELD sense data.
This was causing some clients to not properly fall back, so go ahead
and use the correct TCM_UNSUPPORTED_SCSI_OPCODE sense for this case.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use IP_FREEBIND socket option so that iscsi portal configuration with
explicit IP addresses can happen during boot, before network interfaces
have been assigned IPs.
This is especially important on systemd based Linux boxes where system
boot happens asynchronously and non-trivial configuration must be done
to get targetcli.service to start synchronously after the network is
configured.
Reference:
http://lists.fedoraproject.org/pipermail/devel/2011-October/158025.html
Signed-off-by: Dax Kelson <dkelson@gurulabs.com>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: "Andy Grover" <agrover@redhat.com>
Cc: "Lennart Poettering" <lennart@poettering.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Requesting to many bvecs upsets bio_alloc_bioset, so limit the number we ask
for to the amount it can handle.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These are root only and we're not likely to hit the problem in practise,
but it makes the static checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fixes this error after a recent nfs cleanup:
drivers/target/iscsi/iscsi_target_configfs.c: In function 'lio_target_call_addnptotpg':
drivers/target/iscsi/iscsi_target_configfs.c:214:3: error: implicit declaration of function 'in6_pton' [-Werror=implicit-function-declaration]
drivers/target/iscsi/iscsi_target_configfs.c:239:3: error: implicit declaration of function 'in_aton' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The block layer keeps q->limits.discard_granularity in bytes, but iblock
(and the SCSI Block Limits VPD page) keep unmap_granularity in blocks.
Report the correct value when exporting block devices by dividing to
convert bytes to blocks.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in target_submit_cmd() where the failure path
for transport_generic_allocate_tasks() made a direct call to
transport_send_check_condition_and_sense() and not calling the
final target_put_sess_cmd() release callback.
For transport_generic_allocate_tasks() failures, use the proper call to
transport_generic_request_failure() to handle kref_put() along
with potential internal queue full response processing.
It also makes transport_lookup_cmd_lun() failures in
target_submit_cmd() use transport_send_check_condition_and_sense() and
target_put_sess_cmd() directly to avoid se_cmd->se_dev reference in
transport_generic_request_failure() handling.
Finally it drops the out_check_cond: label and use direct reference for
allocate task failures, and per-se_device queue_full handling is
currently not supported for transport_lookup_cmd_lun() failure
descriptors due to se_device dependency.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Retval not very useful, and may even be harmful. Once submitted, fabrics
should expect a sense error if anything goes wrong. All fabrics checking
of this retval are useless or broken:
fc checks it just to emit more debug output.
ib_srpt trickles retval up, then it is ignored.
qla2xxx trickles it up, which then causes a bug because the abort goto
in qla_target.c thinks cmd hasn't been sent to target.
Just returning nothing is best.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
WindowsXP+BOT issues a MODE_SENSE request with page 0x1c which is not
suppoerted by target. Target rejects that command with
TCM_INVALID_CDB_FIELD, so far so good. On BOT I can't send the SENSE
response back, instead I can only reply that an error occured. The next
thing happens is a REQUEST_SENSE request with 18 bytes length. Since the
check here is more than 18 bytes I have to NACK that request as well.
This is not really required: We check for some additional room, but we
never use it. The additional length is set to 0xa so the total length is
0xa + 8 = 18 which is fine with my 18 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
My draft of SPC-4 says:
If the PAGE CODE field is not set to zero when the EVPD bit is set
to zero, the command shall be terminated with CHECK CONDITION
status, with the sense key set to ILLEGAL REQUEST, and the
additional sense code set to INVALID FIELD IN CDB.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
My draft of SPC-4 says:
If the device server does not implement the requested vital product
data page, then the command shall be terminated with CHECK CONDITION
status, with the sense key set to ILLEGAL REQUEST, and the
additional sense code set to INVALID FIELD IN CDB.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug with sendtargets discovery where INADDR_ANY (0.0.0.0)
+ IN6ADDR_ANY_INIT ([0:0:0:0:0:0:0:0]) network portals where incorrectly being
reported back to initiators instead of the address of the connecting interface.
To address this, save local socket ->getname() output during iscsi login setup,
and makes iscsit_build_sendtargets_response() return these TargetAddress keys
when INADDR_ANY or IN6ADDR_ANY_INIT portals are in use.
Reported-by: Dax Kelson <dkelson@gurulabs.com>
Reported-by: Andy Grover <agrover@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We need to handle >1 page control cdbs, so extend the code to do a vmap
if bigger than 1 page. It seems like kmap() is still preferable if just
a page, fewer TLB shootdowns(?), so keep using that when possible.
Rename function pair for their new scope.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A statement such as
struct iscsi_node_attrib *na = na = iscsit_tpg_get_node_attrib(sess);
has undefined behaviour since there are two assignments to 'na', strictly
speaking (the order in which side-effects from the assignments take place
is undefined since there's no intervening sequence point), and it looks
unintentional in any case.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed bitfields are a problem because instead of being 1 or 0 like
you'd expect they are 0 and -1. It doesn't cause a problem in this case
but sparse complains:
drivers/target/iscsi/iscsi_target_core.h:564:56: error: dubious one-bit
signed bitfield
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where the iscsit_add_reject_from_cmd() call
from a failure to iscsit_alloc_buffs() was incorrectly passing
add_to_conn=1 and causing a double list_add after iscsi_cmd->i_list
had already been added in iscsit_handle_scsi_cmd().
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- core_tpg_pre_addlun()
returns always ERR_PTR() or the pointer, never NULL. The additional
check for NULL in core_dev_add_lun() is not required.
- core_tpg_pre_dellun()
returns always ERR_PTR() or the pointer, never NULL. The check for NULL
in core_dev_del_lun() is wrong. The third argument (int *) is never
used, remove it.
- core_dev_add_lun()
returns always NULL or the pointer, never ERR_PTR. The check for
IS_ERR() is not required.
(nab: Convert core_dev_add_lun() use err.h macros for failure
handling to be consistent with the rest of target_core_fabric_configfs.c
callers)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It may happen that uasp will free the request in irq conntext, the
callchain:
uasp_cmd_release() -> transport_generic_free_cmd() -> core_dec_lacl_count()
where the last function enables the IRQ. Those irqs are re-disabled
later (due to the spin.*irq_restore) but in between we could get hurt.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The multiple calls to pr_debug() each with one letter results in a new
line. This patch merges the multiple requests into one call per line
so we don't have the multiple line cuts.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a work-around for handling zero allocation length
control CDBs (type SCF_SCSI_CONTROL_SG_IO_CDB) that was causing an
OOPs with the following raw calls:
# sg_raw -v /dev/sdd 3 0 0 0 0 0
# sg_raw -v /dev/sdd 0x1a 0 1 0 0 0
This patch will follow existing zero-length handling for data I/O
and silently return with GOOD status. This addresses the zero length
issue, but the proper long-term resolution for handling arbitary
allocation lengths will be to refactor out data-phase handling in
individual CDB emulation logic within target_core_cdb.c
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
According to SPC-4, the sense key for commands that are failed with
INVALID FIELD IN PARAMETER LIST and INVALID FIELD IN CDB should be
ILLEGAL REQUEST (5h) rather than ABORTED COMMAND (Bh). Without this
patch, a tcm_loop LUN incorrectly gives:
# sg_raw -r 1 -v /dev/sda 3 1 0 0 ff 0
Sense Information:
Fixed format, current; Sense key: Aborted Command
Additional sense: Invalid field in cdb
Raw sense data (in hex):
70 00 0b 00 00 00 00 0a 00 00 00 00 24 00 00 00
00 00
While a real SCSI disk gives:
Sense Information:
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid field in cdb
Raw sense data (in hex):
70 00 05 00 00 00 00 18 00 00 00 00 24 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
with the main point being that the real disk gives a sense key of
ILLEGAL REQUEST (5h).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Doing alloc_page(GFP_KERNEL | __GFP_ZERO) to get pages used for data
buffers wastes a lot of CPU clearing pages that will be quickly be
overwritten by the actual data. However, for emulated control
commands such as INQUIRY and so on, the code does assume that the
buffer is zeroed.
To avoid this CPU overhead, skip the __GFP_ZERO for commands that are
actually moving data, ie cmds that have SCF_SCSI_DATA_SG_IO_CDB set.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Initiators that aren't the active reservation holder should be able to
do a PERSISTENT RESERVE IN command in all cases, so add it to the list
of allowed CDBs in core_scsi3_pr_seq_non_holder().
Signed-off-by: Marco Sanvido <marco@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The comments quote the right parts of the spec:
* d) Establish a unit attention condition for the
* initiator port associated with every I_T nexus
* that lost its registration other than the I_T
* nexus on which the PERSISTENT RESERVE OUT command
* was received, with the additional sense code set
* to REGISTRATIONS PREEMPTED.
and
* e) Establish a unit attention condition for the initiator
* port associated with every I_T nexus that lost its
* persistent reservation and/or registration, with the
* additional sense code set to REGISTRATIONS PREEMPTED;
but the actual code accidentally uses ASCQ_2AH_RESERVATIONS_PREEMPTED
instead of ASCQ_2AH_REGISTRATIONS_PREEMPTED. Fix this.
Signed-off-by: Marco Sanvido <marco@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We never embedd the bio into a structure, so there is no need to allocate
64 bytes of headroom per bio.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The target code was not setting the additional sense length field in the
sense data it returned, which meant that at least the Linux stack
ignored the ASC/ASCQ fields. For example, without this patch, on a
tcm_loop device:
# sg_raw -v /dev/sda 2 0 0 0 0 0
gives
cdb to send: 02 00 00 00 00 00
SCSI Status: Check Condition
Sense Information:
Fixed format, current; Sense key: Illegal Request
Raw sense data (in hex):
70 00 05 00 00 00 00 00
while after the patch we correctly get the following (which matches what
a regular disk returns):
cdb to send: 02 00 00 00 00 00
SCSI Status: Check Condition
Sense Information:
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid command operation code
Raw sense data (in hex):
70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00
00 00
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes a legacy se_dev_check_online() check from within
transport_execute_tasks() that should no longer be necessary as
transport_lookup_cmd_lun() is already making this call.
Using transport_cmd_check_stop() from transport_execute_tasks() should
already be checking per se_cmd context for each descriptor upon active
I/O shutdown, so no need to acquire dev->dev_status_lock again while
executing se_task submission.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes the original usage of __transport_execute_tasks() ahead
of every transport_get_cmd_from_queue() call in transport_processing_thread().
This helps reduce se_device->execute_task_lock contention between qla2xxx wq
with target_submit_cmd() for READs and transport_processing_thread()
context servicing WRITEs with full payloads for I/O submission.
It also adds a __transport_execute_tasks() to kick the task queue again
without a *se_cmd descriptor with existing queue full logic, but this may
end up not being necessary.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes __transport_execute_tasks() perform the addition of
tasks to dev->execute_task_list via __transport_add_tasks_from_cmd()
while holding dev->execute_task_lock during normal I/O fast path
submission.
It effectively removes the unnecessary re-acquire of dev->execute_task_lock
during transport_execute_tasks() -> transport_add_tasks_from_cmd() ahead
of calling __transport_execute_tasks() to queue tasks for the passed
*se_cmd descriptor.
(v2: Re-add goto check_depth usage for multi-task submission for now..)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Historically, pSCSI devices have been the ones that required target-core
to enforce a per se_device->depth_left. This patch changes target-core
to no longer (by default) enforce a per se_device->depth_left or sleep in
transport_tcq_window_closed() when we out of queue slots for all backend
export cases.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes __transport_execute_tasks() use a local *se_dev
reference to prevent direct se_cmd->se_dev access after
transport_cmd_check_stop() -> transport_add_tasks_from_cmd()
has been called, as in the current implementation we can expect
__transport_execute_tasks() may be called from another context
that may have already completed the I/O.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the main ft_send_work() I/O path to use
target_submit_cmd() with a single se_cmd->cmd_kref reference
that is released via the existing ft_check_stop_free() response
path callback.
It also makes ft_send_tm() use transport_init_se_cmd() and
target_get_sess_cmd() to also use single se_cmd->cmd_kref
reference.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a target_submit_cmd() caller that can be used by fabrics
to submit an uninitialized se_cmd descriptor to an struct se_session +
unpacked_lun from workqueue process context. This call will invoke the
following steps:
- transport_init_se_cmd() to setup se_cmd specific pointers
- Obtain se_cmd->cmd_kref references with target_get_sess_cmd()
- set se_cmd->t_tasks_bidi
- transport_lookup_cmd_lun() to setup struct se_cmd->se_lun from
the passed unpacked_lun
- transport_generic_allocate_tasks() to setup the passed *cdb, and
- transport_handle_cdb_direct() handle READ dispatch or WRITE
ready-to-transfer callback to fabric
v2 changes from hch feedback:
*) Add target_sc_flags_table for target_submit_cmd flags
*) Rename bidi parameter to flags, add TARGET_SCF_BIDI_OP
*) Convert checks to BUG_ON
*) Add out_check_cond for transport_send_check_condition_and_sense
usage
v3 changes:
*) Add TARGET_SCF_ACK_KREF for target_submit_cmd into
target_get_sess_cmd to determine when the fabric caller is expecting
a second kref_put() from fabric packet acknowledgement.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves target_put_sess_cmd() to use a se_cmd->cmd_kref
callback target_release_cmd_kref when performing driver release of
fabric->se_cmd descriptor memory. It sets the default cmd_kref
count value to '2' within target_get_sess_cmd() setup, and
currently assumes TFO->check_stop_free() usage.
It drops se_tfo->check_release_cmd() usage in the main
transport_release_cmd codepath.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Current SCSI specs say that the "response format" field in the standard
INQUIRY response should be set to 2, and all the real SCSI devices I
have do put 2 here. So let's do that too.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is not reason to artifically limit max_sectors in tcm_loop, set
it to UINT_MAX to allow stressing the large I/O handling in the target
core using the loopback driver. Also remove various superflous defines
hiding the values set in the host template.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch strips the trailing newline from backend device udev_path and
alias attributes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes chap_server_compute_md5() use proper unsigned long
usage for the CHAP_I (identifier) and check for values beyond 255 as
per RFC-1994.
Reported-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A reader should spend an extra moment whenever noticing a cast,
because either something special is going on that deserves extra
attention or, as is all too often the case, the code is wrong.
These casts, afaics, have all been useless. They cast a foo* to a
foo*, cast a void* to the assigned type, cast a foo* to void*, before
assigning it to a void* variable, etc.
In a few cases I also removed an additional &...[0], which is equally
useless.
Lastly I added three FIXMEs where, to the best of my judgement, the
code appears to have a bug. It would be good if someone could check
these.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- rename to target_check_cdb_and_preempt
- use non-safe list_for_each_entry
- move common check into callee (simplifying callers)
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The command
| echo rd_pages=32768 > ramdisk/control
Does not work because it writes "rd_pages=32768\n" and the parser which
matches for "rd_pages=%d" does not recognize it due to the \n. One way
of fixing this would be using "echo -n" instead.
This patch adds \n to the list of separators so we don't have to use the
-n argument which I find is more convinient.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is no need to make task_state_active an atomic_t given that it is
always set under the execute_task_lock so we can make it a simple bool.
Also rename it to t_state_active to be closer to the list it guards,
and make sure all checks before the list addion/removal actually happen
under execute_task_lock.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We only reach transport_complete_task once per task, so the test and set on
task_error_status is never going to have an effect.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This reorganized the headers under include/target into:
- target_core_base.h stays as is with all target-wide data stuctures and defines
- target_core_backend.h contains the whole interface to I/O backends
- target_core_fabric.h contains the whole interface to fabric modules
Except for those only the various configfs macro headers stay around.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Create a new headers, drivers/target/target_core_internal.h that is supposed
to hold all target_core-internal prototypes. Move all non-exported includes
from include/target to it, and merge the smaller prototype-only includes
inside drivers/target into it as well. Mark functions that were found to
not be called outside their implementation file static.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix the following compile warning with hex2bin() usage:
drivers/target/iscsi/iscsi_target_auth.c: In function ‘chap_string_to_hex’:
drivers/target/iscsi/iscsi_target_auth.c:35: warning: ignoring return value of ‘hex2bin’, declared with attribute warn_unused_result
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If an attribute is present (but not yet supported) it should be OK
to write 0 (a no-op) to the attribute.
This is an issue because userspace should be able to save and restore all
set attribute values without error.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
So the code assumes that the sg list is only a array while in reality
loopback SGL memory via scsi_cmnd into target-core may be already
chained. This patch converts ramdisk code to use sg_miter logic from
scatterlist.h in order to properly support passthrough SGL usage with
transport_generic_map_mem_to_cmd() via loopback.
With this patch the bug goes away. However after umount/mount of the
device my files are gone. So something is still not right. After looking
at it for a while I decided to rewrite the that part of the code and now
things do work for me.
For reference:
- http://article.gmane.org/gmane.linux.scsi.target.devel/595
the sg_next() conversion
- http://article.gmane.org/gmane.linux.scsi.target.devel/602
the rewrite of the copy code
(nab: Fix compile warning in rd_MEMCPY)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Breakout rd_MEMCPY_do_task() usage of do_div() to tmp value during
rd_request->rd_page assignment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes fileio to use for_each_sg() when walking se_task->task_sg
memory passed into from loopback LLD struct scsi_cmnd scatterlist memory.
This addresses an issue where FILEIO backends with loopback where hitting the
following OOPs with mkfs.ext2:
|kernel BUG at include/linux/scatterlist.h:97!
|invalid opcode: 0000 [#1] PREEMPT SMP
|Modules linked in: sd_mod tcm_loop target_core_stgt scsi_tgt target_core_pscsi target_core_file target_core_iblock target_core_mod configfs scsi_mod
|
|Pid: 671, comm: LIO_fileio Not tainted 3.1.0-rc10+ #139 Bochs Bochs
|EIP: 0060:[<e0afd746>] EFLAGS: 00010202 CPU: 0
|EIP is at fd_do_task+0x396/0x420 [target_core_file]
| [<e0aa7884>] __transport_execute_tasks+0xd4/0x190 [target_core_mod]
| [<e0aa797c>] transport_execute_tasks+0x3c/0xf0 [target_core_mod]
|EIP: [<e0afd746>] fd_do_task+0x396/0x420 [target_core_file] SS:ESP 0068:dea47e90
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some are never used, some are set but never read, dev_hoq_count is
incremented and decremented, but never read.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The LSB of the page length is at offset 3, not 2.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SBC-3 says:
A TRANSFER LENGTH field set to zero specifies that 256 logical
blocks shall be written. Any other value specifies the number
of logical blocks that shall be written.
The old code was always just returning the value in the TRANSFER LENGTH
byte. Fix this to return 256 if the byte is 0.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
IO commands with a TRANSFER LENGTH of 0 are not an error; for example,
for READ (10) and WRITE (10), SBC-3 says:
A TRANSFER LENGTH field set to zero specifies that no logical blocks
shall be read. This condition shall not be considered an error.
In case we have nothing to do, just complete the command with good status.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch sets the missing ISCSI_FLAG_CMD_FINAL bit in
iscsit_send_task_mgt_rsp() for a struct iscsi_tm_rsp PDU.
This usage is hardcoded for all TM response PDUs in RFC-3720
section 10.6.
Reported-by: whucecil <whucecil1999@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes iscsi-target handling of underflow where residual data is
causing an OOPs by using the incorrect iscsi_cmd_t->data_length initially
assigned in iscsit_allocate_se_cmd(). It resets iscsi_cmd_t->data_length
from se_cmd_t->data_length after transport_generic_allocate_tasks()
has been invoked in iscsit_handle_scsi_cmd() RX context, and converts
iscsi_cmd->residual_count usage to access iscsi_cmd->se_cmd.residual_count
to get the proper residual count set by target-core.
Reported-by: <lists@internyc.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes transport_generic_map_mem_to_cmd() to reject SCSI data
overflow and to send exception status with CHECK_CONDITION + TCM_INVALID_CDB_FIELD
for fabrics that are passing a pre-populated struct scatterlist (eg: tcm_loop
and iscsi-target) being mapped into se_cmd->t_data_sg and se_cmd->t_data_nents.
This addresses an OOPs where transport_allocate_data_tasks() would walk
the incorrect post OVERFLOW cmd->data_length value beyond the end of
the passed scatterlist.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We never walk ordered_cmd_list in the se_device, so remove all code related
to supporting it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We already have a perfectly valid se_device pointer in the command, so
remove the mostly useless duplicates.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes config_item_name() informational usage of
TFO->free_wwn() treewide in loopback, tcm_fc, ib_srpt and
tcm_vhost module code.
Using v4 target_core_fabric_configfs.c logic, a fabric call for
config_item_name() in TFO->drop_wwn() context returns NULL as
target_fabric_drop_wwn() invoking config_item_put() ->
config_group_put() will release fabric_port->port_wwn.wwn_group
before the last config_item_put() -> TFO->drop_wwn() is
invoked.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
While testing ib_srpt I noticed that the target system became
rather unresponsive during intensive I/O. The patch below made
my target system responsive again during I/O without decreasing
performance.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds missing kfree() for an allocation in iscsi_login_zero_tsih_s1()
code, and make transport_init_session() check for IS_ERR() returns.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes legacy usage of PYX_TRANSPORT_* return codes in a number
of locations and addresses cases where transport_generic_request_failure()
was returning the incorrect sense upon CHECK_CONDITION status after the
v3.1 converson to use errno return codes.
This includes the conversion of transport_generic_request_failure() to
process cmd->scsi_sense_reason and handle extra TCM_RESERVATION_CONFLICT
before calling transport_send_check_condition_and_sense() to queue up
response status. It also drops PYX_TRANSPORT_OUT_OF_MEMORY_RESOURCES legacy
usgae, and returns TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE w/ a response
for these cases.
transport_generic_allocate_tasks(), transport_generic_new_cmd(), backend
SCF_SCSI_DATA_SG_IO_CDB ->do_task(), and emulated ->execute_task() have
all been updated to set se_cmd->scsi_sense_reason and return errno codes
universally upon failure. This includes cmd->scsi_sense_reason assignment
in target_core_alua.c, target_core_pr.c and target_core_cdb.c emulation code.
Finally it updates fabric modules to remove the legacy usage, and for
TFO->new_cmd_map() callers forwards return values outside of fabric code.
iscsi-target has also been updated to remove a handful of special cases
related to the cleanup and signaling QUEUE_FULL handling w/ ft_write_pending()
(v2: Drop extra SCF_SCSI_CDB_EXCEPTION check during failure from
transport_generic_new_cmd, and re-add missing task->task_error_status
assignment in transport_complete_task)
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Instead of calling into transport_emulate_control_cdb from
__transport_execute_tasks for some CDBs always set up ->exectute_tasks
in the command sequence and use it uniformly.
(nab: Add default passthrough break for SERVICE_ACTION_IN)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All ->execute_task instances now need to complete the I/O explicitly,
which can either happen synchronously or asynchronously.
Note that a lot of the CDB emulations appear to return success even if
some lowlevel operations failed. Given that this is an existing issue
this patch doesn't change that fact.
(nab: Adding missing switch breaks in PR-IN + PR_OUT)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Encapsulate each CDB emulation into a function of its own, to prepare
setting ->exectute_task to these routines.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We want to be able to handle all CDBs through it and remove hacks like
always using the first task in a CDB in target_report_luns.
Also rename the callback to ->execute_task to better describe its use.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Split core_scsi2_emulate_crh into one routine each for the
PERSISTENT_RESERVE_IN and PERSISTENT_RESERVE_OUT side.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Split core_scsi2_emulate_crh into one routine each for the reserve and
release side. The common code now is in a helper called by both
routines.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the initial pieces of generic active I/O shutdown logic.
This is intended to be a 'opt-in' feature for fabric modules that
includes the following functions to provide a mechinism for fabric
modules to track se_cmd via se_session->sess_cmd_list:
*) target_get_sess_cmd() - Add se_cmd to sess->sess_cmd_list, called
from fabric module incoming I/O path.
*) target_put_sess_cmd() - Check for completion or drop se_cmd from
->sess_cmd_list
*) target_splice_sess_cmd_list() - Splice active I/O list from
->sess_cmd_list to ->sess_wait_list, can called with HW fabric
lock held.
*) target_wait_for_sess_cmds() - Walk ->sess_wait_list waiting on
individual ->cmd_wait_comp. Optional transport_wait_for_tasks()
call.
target_splice_sess_cmd_list() is allowed to be called under HW fabric
lock, and performs the splice into se_sess->sess_wait_list and set
se_cmd->cmd_wait_set. Then target_wait_for_sess_cmds() walks the list
waiting for individual target_put_sess_cmd() fabric callbacks to
complete.
It also adds TFO->check_release_cmd() to split the completion and memory
release calls, where a fabric module uses target_put_sess_cmd() to check
for I/O completion during session shutdown. This is currently pushed out
into fabric modules as current fabric code may sleep here waiting for
TFO->check_stop_free() to complete in main response path, and because
target_wait_for_sess_cmds() calling TFO->release_cmd() to free fabric
descriptor memory directly.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
The commit
target: use a workqueue for I/O completions
accidentally removed setting t_tasks_failed in transport_complete_task.
Add it back in a slightly cleaner way; now it is set for every failed task
instead of special casing the last one completing by using the success
argument directly for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
The check is wrong here because blk_make_request() returns an
ERR_PTR() and it doesn't return NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch drops TRANSPORT_FREE_CMD_INTR usage from target core, which
includes the removal of transport_generic_free_cmd_intr() symbol,
TRANSPORT_FREE_CMD_INTR usage in transport_processing_thread(), and
special case LUN_RESET handling to skip TRANSPORT_FREE_CMD_INTR processing
in core_tmr_drain_cmd_list(). We now expect that fabric modules will
use an internal workqueue to provide process context when releasing
se_cmd descriptor resources via transport_generic_free_cmd().
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Madhuranath Iyengar <mni@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch converts target_core_fabric_ops->check_stop_free() usage in
transport_cmd_check_stop() and associated fabric module usage to
return '1' when the passed se_cmd has been released directly within
->check_stop_free(), or return '0' when the passed se_cmd has not
been released.
This addresses an issue where transport_cmd_finish_abort() ->
transport_cmd_check_stop_to_fabric() was leaking descriptors during
LUN_RESET for modules using ->check_stop_free(), but not directly
releasing se_cmd in all cases.
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch addresses two issues with non immediate TMR handling in
iscsit_handle_task_mgt_cmd(). The first involves breakage due to
v3.1-rc conversion of iscsit_sequence_cmd(), which upon good status
would hit the iscsit_add_reject_from_cmd() block of code. This patch
adds an explict check for CMDSN_ERROR_CANNOT_RECOVER.
The second adds a check to return when non immediate TMR operation is
detected after iscsit_ack_from_expstatsn(), as iscsit_sequence_cmd()
-> iscsit_execute_cmd() will have called transport_generic_handle_tmr()
for the non immediate TMR case already.
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a missing CMDSN_LOWER_THAN_EXP return check for
iscsit_sequence_cmd() in iscsit_handle_scsi_cmd() that was incorrectly
dropped during the v3.1-rc cleanups to use iscsit_sequence_cmd().
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
After the list_del() in core_tmr_drain_tmr_list(),
core_tmr_release_req() would list_del() the same object again.
Call graph:
core_tmr_drain_tmr_list
transport_cmd_finish_abort_tmr
transport_generic_remove
transport_free_se_cmd
core_tmr_release_req
So use list_del_init(), as list_del() of an initialized list_head is
safe and essentially a nop. In the CONFIG_DEBUG_LIST case, list_del()
actually poisons the list_head, but that is fine as we free the object
directly afterwards.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch adds a handful minor cleanups to core_tmr_drain_tmr_list() that
remove an unnecessary NULL check, use list_for_each_entry_safe() instead of
list_entry(), and makes the drain_tmr_list walk use *tmr_p instead of
directly referencing the passed *tmr function parameter.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Joern Engel <joern@logfs.org>
Reviewed-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes another bug from LUN_RESET re-org fallout in
core_tmr_drain_tmr_list() that was adding the wrong se_tmr_req
into the local drain_tmr_list to be walked + released.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Joern Engel <joern@logfs.org>
Reviewed-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in core_tmr_drain_tmr_list() where drain_tmr_list
was using the wrong se_tmr_req for cmd assignment due to a typo during the
LUN_RESET re-org. This was resulting in general protection faults while
using the leftover bogus *tmr_p pointer from list_for_each_entry_safe().
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Joern Engel <joern@logfs.org>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target core to also check for -ENOMEM from fabric callbacks
to signal QUEUE_FULL status, instead of just -EAGAIN in order to catch a
larger set of fabric failure cases that want to trigger QUEUE_FULL logic.
This includes the callbacks for ->write_pending(), ->queue_data_in() and
->queue_status().
It also makes transport_generic_write_pending() return zero upon QUEUE_FULL,
and removes two unnecessary -EAGAIN checks to catch write pending QUEUE_FULL
cases from transport_generic_new_cmd() failures in transport_handle_cdb_direct()
and transport_processing_thread():TRANSPORT_NEW_CMD_MAP state.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch addresses an issue with buggy userspace code sending I/O
via scsi-generic that does not explictly clear their associated read
buffers. It adds an explict memset of the first SGL entry within
tcm_loop_new_cmd_map() for SCF_SCSI_CONTROL_SG_IO_CDB payloads that
are currently guaranteed to be a single SGL by target-core code.
This issue is a side effect of the v3.1-rc1 merge to remove the
extra memcpy between certain control CDB types using a contigious
+ cleared buffer in target-core, and performing a memcpy into the
SGL list within tcm_loop.
It was originally mainfesting itself by udev + scsi_id + scsi-generic
not properly setting up the expected /dev/disk/by-id/ symlinks because
the INQUIRY payload was containing extra bogus data preventing the
proper NAA IEEE WWN from being parsed by userspace.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the following compile warning in target_core_cdb.c in
recent linux-next code due to the new use of EXPORT_SYMBOL() for
target_get_task_cdb().
drivers/target/target_core_cdb.c:1316: warning: data definition has no type or storage class
drivers/target/target_core_cdb.c:1316: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
drivers/target/target_core_cdb.c:1316: warning: parameter names (without types) in function declaration
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (62 commits)
target: Fix compile warning w/ missing module.h include
target: Remove legacy se_task->task_timer and associated logic
target: Fix incorrect transport_sent usage
target: re-use the command S/G list for single-task commands
target: Fix BIDI t_task_cdb handling in transport_generic_new_cmd
target: remove transport_allocate_tasks
target: merge transport_new_cmd_obj into transport_generic_new_cmd
target: remove the task_sg_bidi field se_task and pSCSI BIDI support
target: transport_subsystem_check_init cleanups
target: use a workqueue for I/O completions
target: remove unused TRANSPORT_ states
target: remove TRANSPORT_DEFERRED_CMD state
target: remove the TRANSPORT_REMOVE state
target: move depth_left manipulation out of transport_generic_request_failure
target: stop task timers earlier
target: remove TF_TIMER_STOP
target: factor some duplicate code for stopping a task
target: fix list walking in transport_free_dev_tasks
target: use transport_cmd_check_stop_to_fabric consistently
target: do not pass the queue object to transport_remove_cmd_from_queue
...
* 'next' of git://selinuxproject.org/~jmorris/linux-security: (95 commits)
TOMOYO: Fix incomplete read after seek.
Smack: allow to access /smack/access as normal user
TOMOYO: Fix unused kernel config option.
Smack: fix: invalid length set for the result of /smack/access
Smack: compilation fix
Smack: fix for /smack/access output, use string instead of byte
Smack: domain transition protections (v3)
Smack: Provide information for UDS getsockopt(SO_PEERCRED)
Smack: Clean up comments
Smack: Repair processing of fcntl
Smack: Rule list lookup performance
Smack: check permissions from user space (v2)
TOMOYO: Fix quota and garbage collector.
TOMOYO: Remove redundant tasklist_lock.
TOMOYO: Fix domain transition failure warning.
TOMOYO: Remove tomoyo_policy_memory_lock spinlock.
TOMOYO: Simplify garbage collector.
TOMOYO: Fix make namespacecheck warnings.
target: check hex2bin result
encrypted-keys: check hex2bin result
...
This patch fixes the following compile warning in target_core_cdb.c in
recent linux-next code due to the new use of EXPORT_SYMBOL() for
target_get_task_cdb().
drivers/target/target_core_cdb.c:1316: warning: data definition has no type or storage class
drivers/target/target_core_cdb.c:1316: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
drivers/target/target_core_cdb.c:1316: warning: parameter names (without types) in function declaration
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Christoph Hellwig
