When we access attributes of an rdev (component device on an md array) through
sysfs, we really need to lock the array against concurrent changes. We
currently do that when we change an attribute, but not when we read an
attribute. We need to lock when reading as well else rdev->mddev could become
NULL while we are accessing it.
So add appropriate locking (mddev_lock) to rdev_attr_show.
rdev_size_store requires some extra care as well as it needs to unlock the
mddev while scanning other mddevs for overlapping regions. We currently
assume that rdev->mddev will still be unchanged after the scan, but that
cannot be certain. So take a copy of rdev->mddev for use at the end of the
function.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A resync/reshape/recovery thread will refuse to progress when the array is
marked read-only. So whenever it mark it not read-only, it is important to
wake up thread resync thread. There is one place we didn't do this.
The problem manifests if the start_ro module parameters is set, and a raid5
array that is in the middle of a reshape (restripe) is started. The array
will initially be semi-read-only (meaning it acts like it is readonly until
the first write). So the reshape will not proceed.
On the first write, the array will become read-write, but the reshape will not
be started, and there is no event which will ever restart that thread.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a raid1 array is stopped, all components currently get added to the list
for auto-detection. However we should really only add components that were
found by autodetection in the first place. So add a flag to record that
information, and use it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure the data doesn't start before the end of the superblock when the
superblock is at the start of the device.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On an md array with a write-intent bitmap, a thread wakes up every few seconds
and scans the bitmap looking for work to do. If the array is idle, there will
be no work to do, but a lot of scanning is done to discover this.
So cache the fact that the bitmap is completely clean, and avoid scanning the
whole bitmap when the cache is known to be clean.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When handling a read error, we freeze the array to stop any other IO while
attempting to over-write with correct data.
This is done in the raid1d(raid10d) thread and must wait for all submitted IO
to complete (except for requests that failed and are sitting in the retry
queue - these are counted in ->nr_queue and will stay there during a freeze).
However write requests need attention from raid1d as bitmap updates might be
required. This can cause a deadlock as raid1 is waiting for requests to
finish that themselves need attention from raid1d.
So we create a new function 'flush_pending_writes' to give that attention, and
call it in freeze_array to be sure that we aren't waiting on raid1d.
Thanks to "K.Tanaka" <k-tanaka@ce.jp.nec.com> for finding and reporting this
problem.
Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds struct device argument to sba_alloc_range and ccio_alloc_range, a
preparation for modifications to fix the IOMMU segment boundary problem. This
change enables ccio_alloc_range to access to LLD's segment boundary limits.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After a quick glance at the code, we're getting the DEBUG_SHIRQ spurious
interrupt before we have the adapter template filled in. Real interrupts
appear to be turned on by fcpci*_init(), so move request_irq until just before
that.
Signed-off-by: Kyle McMartin <kmcmartin@redhat.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I used the wrong return convention on hotkey_get_tablet_mode(), breaking a lot
of stuff. Bad Henrique!
Fix it to return the status in the parameter-by-reference, and IO status on
the function return value. Duh.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit e6bafba5b4 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit e6bafba5b4 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit e6bafba5b4 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SM502 has a programmable PLL which can provide the panel pixel clock instead
of the 288MHz and 336MHz PLLs.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
misc_div is a subset of px_div so eliminate the smaller table.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vertical sync height register can only hold 6 bits. Fix the hsync start test
to use > instead of >=. Also add a few clarifying comments.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even though it may not be strictly necessary transp.offset should probably be
0 when alpha channel is not available.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RGB offsets were reversed in 16bpp modes. Simply trying to reverse the
offsets when endianness differs is clearly the wrong thing to do but that is
an issue for another patch.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sm501fb palette code clearly does not handle direct color so change the
driver to use true color visual for 16bpp.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch replaces dev_dbg() by dev_err(), so the user could actually see the
error, instead of wondering why w1 doesn't work. The root cause of the bus
reset error isn't yet debugged though, but this sometimes happens on iPaq
H5555.
And while I'm at it, some cosmetic cleanups also made (few lines were using
spaces instead of tabs).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the error condition clk_get() returns ERR_PTR(..), so checking for NULL
doesn't work. ds1wm module causes a kernel oops when ds1wm clock isn't
registered.
This patch converts NULL check to IS_ERR(), plus uses PTR_ERR()
for the return code.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit id 94f389485e (Separate MPC52xx PSC FIOF
regsiters from the rest of PSC) split the PSC fifo registers away from the
core PSC regs. Doing so broke the mpc52xx_psc_spi driver.
This patch teaches the mpc52xx_psc_spi driver about the new PSC fifo
register definitions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On my system, pkt_open() consumes 584 bytes because the compiler decides to
inline lots of functions that would not normally be part of long call chains.
The following patch fixes that problem on my system.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Cc: Nix <nix@esperi.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct error paths in probe function.
The probe function enables mmio mode so it important to disable the mmio
mode before exiting the probe function. Otherwise, the console is left in
unusable state (garbled fonts at least, lock up at worst).
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VT notifier callbacks need to be aware of console switches. This is already
partially done from console_callback(), but at that time fg_console, cursor
positions, etc. are not yet updated and hence screen readers fetch the old
values.
This adds an update notify after all of the values are updated in
redraw_screen(vc, 1).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds basic get/set time support for the Seiko Instruments S-35390A.
This chip communicates using I2C and is used on the QNAP TS-109/TS-209 NAS
devices.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <david-b@pacbell.net>
Tested-by: Tim Ellis <tim@ngndg.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Lehmann <thomas.lehmann@alumni.tu-berlin.de> verified that this
entry works.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the module init message to tell that the legacy
driver loaded. This makes it less confusing, in case both drivers are loaded.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace broken code that attempted to copy 6 byte array to 64-bit
integer. Due to missing cast to 64-bit integer, left shift operation
were 32-bit and lead to bytes been copied over each other. New code
uses simple memcpy, for greater readability and efficiency.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Slightly more useful if we compare it against the sequence number of the
command we have outstanding, rather than comparing the reply with itself.
Doh. Pointed out by Sebastian Siewior
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I called p54_parse_eeprom() on a hand-coded structure
I managed to make a small mistake with wrap->len which caused
a segfault a few lines down when trying to read entry->len.
This patch changes the validation code to avoid such problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the EEPROM structure is read from hardware, it is
always little endian, annotate that in the struct and
make sure to convert where applicable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch has added pcibios_enable_device() return value check.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the error code path in hpc_power_off_slot().
The Bad DLLP Mask bit must be restored before return.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the class_device cleanup of pci_bus, the error messages when
things go wrong are incorrect. So fix this up to properly report what
is really happening, if things go wrong.
Thanks to Kay for pointing out the issue.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix following warning:
WARNING: vmlinux.o(.text+0x47bdb1): Section mismatch in reference from the function pci_scan_child_bus() to the function .devinit.text:pcibios_fixup_bus()
We had plenty of functions that could be annotated __devinit but due to
the former restriction that exported symbols could not be annotated
they were not so. So annotate these function and fix the references
from the pci/hotplug/* code to silence the resuting warnings.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This field does nothing, and should not be allowed to stick around
incase someone gets any other ideas...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround for the FT232RL-based, Matrix Orbital VK204-25-USB serial port
added to the ftdi_sio driver.
The device has an invalid endpoint descriptor, which must be modified
before it can be used.
Signed-off-by: Kevin Vance <kvance@kvance.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1037) makes a small update to the earlier as1035 patch.
The minimum-length computation shouldn't be done in
usb_stor_access_xfer_buf(), since that routine can be called multiple
times for a single transfer. It should be done in
usb_stor_set_xfer_buf() instead, which gets called only once.
The way it is now isn't really _wrong_, but it isn't really _right_
either. Moving the statement will be an improvement.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the buffering of the status register.
USB core behavior has changed a bit and this buffering was not refreshed
at the right time. The core got buffered old value of HCRHPORT and it
did not detect any devices on boot.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Acked by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: ehci: Fixes completion for multi-qtd URB the short read case
When use of urb->status in the EHCI driver was reworked last August
(commit 14c04c0f88), a bug was inserted
in the handling of early completion for bulk transactions that need
more than one qTD (e.g. more than 20KB in one URB).
This patch resolves that problem by ensuring that the early completion
status is preserved until the URB is handed back to its submitter,
instead of resetting it after each qTD.
Signed-off-by: Misha Zhilin <misha@epiphan.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1040) fixes up the blacklist of USB device quirks. A
couple of lines are broken to comply with the 80-column rule, and
entries are sorted into the proper numerical order.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1039) updates the Kconfig entry for USB_SUSPEND. The
out-of-date reference to "power/state" is fixed, autosuspend is
mentioned, and the dependency on EXPERIMENTAL is removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the mos7820/7840-based B&B USOPTL4_2/USOPTL4_4 USB/RS485
converter to mos7840.c
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core: Fix cleanup when failing device_add().
- Don't call cleanup_device_parent() if we didn't call setup_parent().
- dev->kobj.parent may be NULL when cleanup_device_parent() is called,
so we need to handle glue_dir == NULL in cleanup_glue_dir().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since device_pm_remove(dev) calls dpm_sysfs_remove(dev), it's
incorrect to call the latter after the former in the device_add()
error path.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1041) fixes a bug introduced by the
acquire-all-device-semaphores reversion. The error pathway of
dpm_suspend() fails to reacquire a mutex it should be holding.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
ioat: fix 'ack' handling, driver must ensure that 'ack' is zero
dmaengine: fix sparse warning
fsldma: do not cleanup descriptors in hardirq context
dmaengine: add driver for Freescale MPC85xx DMA controller
Original patch from Tejun Heo <htejun@gmail.com> but should use ->extra_len
and not ->data_len, as we would then overshoot the original request size.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Initialize 'ack' to zero in case the descriptor has been recycled.
Prevents "kernel BUG at crypto/async_tx/async_xor.c:185!"
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: stable@kernel.org
"Cleaning" descriptors involves calling pending callbacks and clients
assume that their callback will only ever happen in softirq context.
Delay cleanup to the tasklet.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Zhang Wei <wei.zhang@freescale.com>
The driver implements DMA engine API for Freescale MPC85xx DMA controller,
which could be used by devices in the silicon. The driver supports the
Basic mode of Freescale MPC85xx DMA controller. The MPC85xx processors
supported include MPC8540/60, MPC8555, MPC8548, MPC8641 and so on.
The MPC83xx(MPC8349, MPC8360) are also supported.
[kamalesh@linux.vnet.ibm.com: build fix]
[dan.j.williams@intel.com: merge mm fixes, rebase on async_tx-2.6.25]
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Acked-by: Kumar Gala <galak@gate.crashing.org>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: fix blkdev_issue_flush() not detecting and passing EOPNOTSUPP back
block: fix shadowed variable warning in blk-map.c
block: remove extern on function definition
cciss: remove READ_AHEAD define and use block layer defaults
make cdrom.c:check_for_audio_disc() static
block/genhd.c: proper externs
unexport blk_rq_map_user_iov
unexport blk_{get,put}_queue
block/genhd.c: cleanups
proper prototype for blk_dev_init()
block/blk-tag.c should #include "blk.h"
Fix DMA access of block device in 64-bit kernel on some non-x86 systems with 4GB or upper 4GB memory
block: separate out padding from alignment
block: restore the meaning of rq->data_len to the true data length
resubmit: cciss: procfs updates to display info about many
splice: only return -EAGAIN if there's hope of more data
block: fix kernel-docbook parameters and files
The FEC driver has a common interrupt handler for all interrupt event
types. It is raised on a number of distinct interrupt vectors.
This handler can't be re-entered while processing an interrupt, so
make sure all requested vectors are flagged as IRQF_DISABLED.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the #define READ_AHEAD 1024 from the driver and uses the
block layer defaults, instead. We have found that under certain workloads
the setting can cause a disk connected to the e200 controller to go offline.
If the disk hiccups the link may try to downshift but the controller is
never notified that the link successfully completed the renegotiation.
We've also found that performance using the block layer default of 32 pages
was on par with the 1024 setting. We tried setting it to zero at one time
based on info from our firmware guys but that killed performance. Turns out
we were talking about 2 different read ahead settings.
Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch makes the needlessly global check_for_audio_disc() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Block layer alignment was used for two different purposes - memory
alignment and padding. This causes problems in lower layers because
drivers which only require memory alignment ends up with adjusted
rq->data_len. Separate out padding such that padding occurs iff
driver explicitly requests it.
Tomo: restorethe code to update bio in blk_rq_map_user
introduced by the commit 40b01b9bbd
according to padding alignment.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The meaning of rq->data_len was changed to the length of an allocated
buffer from the true data length. It breaks SG_IO friends and
bsg. This patch restores the meaning of rq->data_len to the true data
length and adds rq->extra_len to store an extended length (due to
drain buffer and padding).
This patch also removes the code to update bio in blk_rq_map_user
introduced by the commit 40b01b9bbd.
The commit adjusts bio according to memory alignment
(queue_dma_alignment). However, memory alignment is NOT padding
alignment. This adjustment also breaks SG_IO friends and bsg. Padding
alignment needs to be fixed in a proper way (by a separate patch).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
volumes
This patch allows us to display information about all of the logical volumes
configured on a particular controller without stepping on memory even when
there are many volumes (128 or more) configured.
Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch fixes a memory leak introduced by commit
4ccf8cffa9 and spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In C, signed 1-bit bitfields can only take the values 0 and -1, only 0 and 1
are ever assigned in current code. Make them unsigned bitfields.
Fixes the (repeated) sparse errors:
drivers/mtd/ubi/ubi.h:220:15: error: dubious one-bit signed bitfield
drivers/mtd/ubi/ubi.h:221:17: error: dubious one-bit signed bitfield
drivers/mtd/ubi/ubi.h:222:18: error: dubious one-bit signed bitfield
drivers/mtd/ubi/ubi.h:223:16: error: dubious one-bit signed bitfield
drivers/mtd/ubi/ubi.h:224:20: error: dubious one-bit signed bitfield
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
drivers/mtd/ubi/vmt.c: In function `ubi_create_volume':
drivers/mtd/ubi/vmt.c:379: warning: statement with no effect
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Every skb removed from session->reorder_q needs sock_put().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every skb removed from session->reorder_q needs sock_put().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oddly enough, unsigned int c = '\300'; puts a "negative" value in c, not
0300... This fixes the default unicode compose table by using integers
instead of character constants.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/scsi/ibmvscsi/ibmvstgt.c: In function 'ibmvstgt_cmd_done':
drivers/scsi/ibmvscsi/ibmvstgt.c:292: error: 'cmd' undeclared (first use in this function)
drivers/scsi/ibmvscsi/ibmvstgt.c:292: error: (Each undeclared identifier is reported only once
drivers/scsi/ibmvscsi/ibmvstgt.c:292: error: for each function it appears in.)
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_tgt uses REQ_TYPE_BLOCK_PC so scsi_init_io doesn't set the length
for us. scsi_tgt needs to do it by itself.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The scsi midlayer allocates scsi_cmnd->sense_buffer dynamically so we
can't initialize scsi_cmnd (the midlyaer does for us).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Before calling __scsi_alloc_queue, scsi_host->shost_gendev.parent must
be initialized properly.
This patch moves __scsi_alloc_queue after scsi_add_host (like
initiator drivers do).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix docbook problems in fusion source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix docbook problem in SCSI source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The original code would incorrectly hardcode ELS timeout values
rather than using the traditional '2 * r_a_tov' value. In some
cases, the hardcoded values would be larger than the
mailbox-command-timeout and result in a needless BIG_HAMMER (ISP
reset), the typical recovery mechanism employed in such cases.
The second defect in the original code was in the assignment of
the default 'ha->r_a_tov' to twice the traditional value.
Correct this by setting the value to 10 seconds.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For recent ISPs, software must detect OVERRUN conditions by
checking the SS_RESIDUAL_OVER bit during CS_COMPLETE handling.
Update the driver to perform this check, which is consistent with
what earlier firmwares did by explicitly cracking open the
FCP_RSP statuses and returning an CS_DATA_OVERRUN.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's no point in hitting the RISC with what will most
assuredly be an unsucessful reset of the RISC hardware if the
initial stop-firmware mailbox command fails with a time-out
status. Instead, to avoid what could amount to a lengthy
stop-firmware/detect-failure/reset-risc loop, continue with
driver unloading and discard the stop-firmware requirement.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fix up from Daniel Drake for replacing GFP_DMA with something
more sensible has gone in here:
commit 69e562c234
Author: Daniel Drake <dsd@gentoo.org>
Date: Wed Feb 20 13:29:05 2008 +0000
[SCSI] arcmsr: fix message allocation
add a change log and update the version for this.
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ps3rom does:
scsi_for_each_sg(cmd, sgpnt, scsi_sg_count(cmd), k) {
kaddr = kmap_atomic(sg_page(sgpnt), KM_IRQ0);
We cannot do something like that with the clustering enabled (or we
can use scsi_kmap_atomic_sg).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sg driver rounds up the length in struct scatterlist to be a multiple
of 512 in some conditions. So LLDs can't use the data length in a sg
list to calculate residual. Instead, the length in struct scsi_cmnd
should be used.
[Geert: the variable buflen already contains scsi_bufflen(cmd)]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix docbook problems in fusion source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix docbook problems in kernel-api.tmpl.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix docbook problems in USB source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix docbook problem in SCSI source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix docbook problems in rapidio source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bus management workqueue job was in danger to dereference NULL
pointers. Also, after having temporarily lifted card->lock, a few node
pointers and a device pointer may have become invalid.
Add NULL pointer checks and get the necessary references. Also, move
card->local_node out of fw_card_bm_work's sight during shutdown of the
card.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Patch "firewire: fw-sbp2: fix NULL pointer deref. in scsi_remove_device"
had the unintended effect that firewire-sbp2 could not be unloaded
anymore until all SBP-2 devices were unplugged.
We now fix the NULL pointer bug by reacquiring a reference to the sdev
instead of holding a reference to the sdev (and to the module) all the
time.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Jarod Wilson <jwilson@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] wrap kmap_atomic(KM_IRQ0) with local_irq_save/restore()
sata_svw: Add support for HT1100 SATA controller
Interrupts must be disabled if using kmap_atomic(KM_IRQ0), but that was
not the case in a few code paths coming directly from ATA driver
interrupt handlers (which use spin_lock rather than spin_lock_irqsave).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set cap.max_inline_data to the actual max inline data that the adapter
support, so that userspace apps see the right value returned.
Signed-off-by: Jon Mason <jon@opengridcomputing.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit a3cd7d90 ("IB/fmr_pool: ib_fmr_pool_flush() should flush all
dirty FMRs") caused a regression for iSER and was reverted in
e5507736.
This change attempts to redo the original patch so that all used FMR
entries are flushed when ib_flush_fmr_pool() is called without
affecting the normal FMR pool cleaning thread. Simply move used
entries from the clean list onto the dirty list in ib_flush_fmr_pool()
before letting the cleanup thread do its job.
Signed-off-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This reverts commit a3cd7d9070.
The original commit breaks iSER reliably, making it complain:
iser: iser_reg_page_vec:ib_fmr_pool_map_phys failed: -11
The FMR cleanup thread runs ib_fmr_batch_release() as dirty entries
build up. This commit causes clean but used FMR entries also to be
purged. During that process, another thread can see that there are no
free FMRs and fail, even though there should always have been enough
available.
Signed-off-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a CM MAD is received, it is queued to a CM workqueue for
processing. The queued work item references the port and device on
which the MAD was received. If that device is removed from the system
before the work item can execute, the work item will reference freed
memory.
To fix this, flush the workqueue after unregistering to receive MAD,
and before the device is be freed.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current tun/tap driver sets also net device's hw address when asked to
change character device's hw address. This is a good idea, but it
misses RTLN-locking, resulting following error message in 2.6.25-rc3's
inetdev_event() function:
RTNL: assertion failed at net/ipv4/devinet.c (1050)
Attached patch fixes this problem.
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy sas address is showing wrongly (wrong endianness). Fix up the
endian transforms to make this correct.
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (35 commits)
Blackfin Serial Driver: Fix bug - Only insert UART rx char in timer task.
Blackfin Serial Driver: Fix bug - update tx dma buffer tail before wake up processes.
Blackfin Serial Driver: Fix bug - Increase buffer tail immediately before starting tx dma.
[Blackfin] serial driver: Add flow control support to bf54x
[Blackfin] serial driver: Fix bug Poll RTS/CTS status in DMA mode as well
[Blackfin] serial driver: ADSP-BF52x arch/mach support
[Blackfin] serial driver: use simpler comment headers and strip out information that is maintained in the scm's log
[Blackfin] serial driver: rework break flood anomaly handling to be more robust/realistic about what we can actually work around
[Blackfin] serial driver: fix bug - cache the bits of the LSR on systems where the LSR is read-to-clear
[Blackfin] serial driver: fix bug - should not wait for the TFI bit, just clear it when tx stop.
[Blackfin] serial driver: Fix bug serial driver in DMA mode spams history to console on shell restart
[Blackfin] serial driver: Fix bug Free rx dma buffer in shutdown.
[Blackfin] serial driver: Clean up UART DMA code.
Blackfin Serial driver: Fix bug - serial driver in PIO mode cant handle input very quickly
[Blackfin] arch: kill section mismatch warnings
[Blackfin] arch: handle the most common L1 shrinkage case (L1 does not exist for a part) so that any parts labeled for L1 instead get placed into external memory sections
[Blackfin] arch: add bfin_clear_PPIx_STATUS() helper funcs like we have for other parts
[Blackfin] arch: make sure we have proper description/copyright/license lines
[Blackfin] arch: Fix CONFIG_PM support for BF561
[Blackfin] arch: Remove DPMC char driver option
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
arch/sh/drivers/dma/dma-sh.c: Correct use of ! and &
serial: Move asm-sh/sci.h to linux/serial_sci.h.
sh: Fix up HAS_SR_RB typo in entry-macros.
maple: fix device detection
sh: fix rtc_resources setup for sh770x
sh: heartbeat: ioremap is expected to succeed
sh: Storage class should be before const qualifier
maple: remove unused variable
sh: SH5-103 needs to select CPU_SH5.
sh: Rename SH-3 CCR3 reg to avoid synclink_cs clash.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (79 commits)
[X25]: Use proc_create() to setup ->proc_fops first
[WANROUTER]: Use proc_create() to setup ->proc_fops first
[8021Q]: Use proc_create() to setup ->proc_fops first
[IPV4]: Use proc_create() to setup ->proc_fops first
[IPV6]: Use proc_create() to setup ->proc_fops first
[SCTP]: Use proc_create() to setup ->proc_fops first
[PKTGEN]: Use proc_create() to setup ->proc_fops first
[NEIGHBOUR]: Use proc_create() to setup ->proc_fops first
[LLC]: Use proc_create() to setup ->proc_fops first
[IPX]: Use proc_create() to setup ->proc_fops first
[SUNRPC]: Use proc_create() to setup ->proc_fops first
[ATM]: Use proc_create() to setup ->proc_fops first
[SCTP]: Update AUTH structures to match declarations in draft-16.
[SCTP]: Incorrect length was used in SCTP_*_AUTH_CHUNKS socket option
[SCTP]: Clean up naming conventions of sctp protocol/address family registration
[APPLETALK]: Use proc_create() to setup ->proc_fops first
[BNX2X]: add bnx2x to MAINTAINERS
[BNX2X]: update version, remove CVS strings
[BNX2X]: Fix Xmit bugs
[BNX2X]: Prevent PCI queue overflow
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: remove stale comments from ide-dma.c (take 2)
ide: remove ide-tape documentation from Documentation/ide.txt
qd65xx: remove commented out code
ide-tape: schedule driver for removal after 6 months
ide-disk: add missing printk() KERN_* levels
ide: fix sparse warning about shadowing 'flags' symbol
ide-cd: fix CD/DVD burning
ide-cd: fix 'ireason' handling for REQ_TYPE_ATA_PC requests
qd65xx: fix setup of QD6580 Control register
ide: skip probing port if "hdx=noprobe" was used for both devices on it
ide: remove redundant comment from ide_unregister()
hpt366: fix section mismatch warnings
ide-cd: Enable audio play quirk for Optiarc DVD RW AD-5200A drive
Fix hpet_(un)register_irq_handler() for when CONFIG_HPET_EMULATE_RTC=n. They
are provided macros that substitute value 0, but if they are called as
functions and the return value isn't checked, the following warnings appear:
drivers/char/rtc.c: In function `rtc_init':
drivers/char/rtc.c:1063: warning: statement with no effect
drivers/char/rtc.c: In function `rtc_exit':
drivers/char/rtc.c:1157: warning: statement with no effect
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support (including ATAPI DMA) for HT1100 (aka BCM11000) SATA controller.
Signed-off-by: Anantha Subramanyam <ananth@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several endianity corrections in start_xmit()
Fixed TSO bug where packets were missing the TCP flags.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit traffic through an internal queue to prevent overflow.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed locking between fastpath and slowpath operations.
Corrected order of traffic disabling to prevent race when going down
under traffic.
- first have the microcode drop all incoming packets
- then do the slowpath stuff
- only then reset the MAC
Got rid of in_reset_task.
Remove_one() and friends would deference a null pointer if init_one
failed.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the HW attentions, used to indicate an error were not properly
acked.
This will cause the driver to endlessly receive interrupts when such
an error happens.
Had to break the code into smaller chunks because it got too nested.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata A0.158 workaround.
Running in INT#A mode after running with MSI-X fails due to a PCI core
bug.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errors were summed improperly, some stats were missing.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configuration of RX filtering needed the following corrections:
Drop flags need to be set per Rx queue.
Have to tell the microcode to collect drop stats, and properly wait
for them to complete when going down.
Sometimes we failed to detect proper completion due to a logical error
in the wait loop.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly protect PHY access between two devices on the same board with
a HW lock.
Use GPIO to clear all previous configurations before changing link
parameters.
Shut down the external PHY in case of fan failure.
Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.
Resolve the flow control response according to autoneg with external
PHY.
Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.
LASI indication fixes to work with peculiarities of PHYs.
Disable MAC RX to avoid a HW bug when closing the MAC under traffic.
Disable parallel detection on HiGig due to HW limitation.
Updating the shared memory structure to work with the current
bootcode.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct PCI-E info printed by init_one()
In one case it failed to free the netdev.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes various items pointed out during a review of the hwicap driver.
Primarily, reversed memcpy calls, re-entrancy issues, and mutex conversion
have been addressed. There are also fixes to comments to use the kerneldoc
format, as well as some sparse annotations.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Switch the SSB PCI core driver to the new SPROM data structure now that
the old one has been removed.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.
Now we enable the birdge only if the b43{legacy}
drivers are selected.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports. lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.
A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:
drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.
Reorder the things that should be done during a
link tuner reset and during a link tuner start.
Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rssi_a > rssi_b is true and the current antenna
was already antenna A, then rt2x00 incorrectly jumped
to antenna B.
Also don't configure the antenna when there has been
no change in the antenna setup.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix 2 issues in antenna diversity selection.
1) the following statement will always return true.
if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.
2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
| CC drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link the net_device structure of the wireless part to the
corresponding device structure.
Without this, the sysfs node for this net_device would not have
'device' link.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously wrong to use an enum in a little endian struct,
and those other enums should be declared differently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent patch named:
[SCSI] gdth: !use_sg cleanup and use of scsi accessors
has done a bad job in handling internal commands issued by gdth_execute().
Internal commands are issued with device gdth_cmd_str ready made directly
to the card, without any mapping or translations of scsi commands. So here
I added a gdth_cmd_str pointer to the gdth_cmndinfo private structure which
is then copied directly to host.
following this patch is a cleanup that removes the home cooked accessors
and reverts them to regular scsi_cmnd accessors. Since they are not used
anymore. After review maybe the 2 patches should be squashed together.
FIXME: There is still a problem with gdth_get_info(). as reported there
is a WARN_ON trigerd in dma_free_coherent() when doing:
$ cat /proc/sys/gdth/0
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Joerg Dorchain: <joerg@dorchain.net>
Tested-by: Stefan Priebe <s.priebe@allied-internet.ag>
Tested-by: Jon Chelton <jchelton@ffpglobal.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
gdth_exit would first remove all cards then stop the timer
and would not sync with the timer function. This caused a crash
in gdth_timer() when module was unloaded.
So del_timer_sync the timer before we delete the cards.
also the reboot notifier function would crash. So clean
that up and fix the crashes.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Joerg Dorchain: <joerg@dorchain.net>
Tested-by: Stefan Priebe <s.priebe@allied-internet.ag>
Tested-by: Jon Chelton <jchelton@ffpglobal.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The old tools did not set max session cmds. This is a regression.
I removed the check when merging the power of 2 patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt moderation low threshold value was incorrectly triggering,
indicating that the threshold should be lowered.
The impact was the timer was likely to become 40usecs and get stuck
there. The biggest side effect was too many interrupts and nonoptimal
performance.
Signed-off-by: John Lacombe <jlacombe@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With commit ef19454b ("[LIB] crc32c: Keep intermediate crc state in
cpu order"), the behavior of crc32c changes on big-endian platforms.
Our algorithm expects the previous behavior; otherwise we have RDMA
connection establishment failure on big-endian platforms like powerpc.
Apply cpu_to_le32() to value returned by crc32c() to get the previous
behavior.
Signed-off-by: Faisal Latif <flatif@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Just delete the debugging statement so we don't use cqp_request after
freeing it. Adrian Bunk flagged this use-after-free issue spotted by
the Coverity checker.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- ide-dma.c is not a separate module
- ide-dma.c is not PCI specific anymore
- DMA is enabled by default nowadays
- link for Intel Zappa BIOS is dead
etc.
v2:
* Some comments should be preserved. (Noticed by Mark Lord)
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drivers/ide/ide.c:801:18: warning: symbol 'flags' shadows an earlier one
drivers/ide/ide.c:732:16: originally declared here
Also fix some whitespace damage while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move counting of sense bytes into the transfer loop.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Pass 'struct request *rq' to ide_cd_check_ireason() from cdrom_newpc_intr()
and use ide_cd_check_ireason() also for REQ_TYPE_ATA_PC requests.
This fixes some hangs caused by not finishing the transfer before ending
the request and also makes use of 'ireason == 1' quirk for spurious IRQs.
Tested-by: Brad Rosser <brad.rosser@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Skip probing port if "hdx=noprobe" parameter was used for both devices on it.
* Obsolete "idex=noprobe" parameter - it only works for ide_generic, cmd640
and PCI hosts in Compatibility mode (on alpha/x86/ia64/m32r/mips/ppc32).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hpt366: fix section mismatch warnings
Fix following warnings:
WARNING: o-sparc64/vmlinux.o(.data+0x195a38): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt370
WARNING: o-sparc64/vmlinux.o(.data+0x195a40): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt370a
WARNING: o-sparc64/vmlinux.o(.data+0x195a48): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt372
WARNING: o-sparc64/vmlinux.o(.data+0x195a50): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt372n
Replace a static array with a small switch resulting in
more readable code.
Mark the pci table __devinitconst.
A lot of variables are const but annotated __devinitdata.
Annotating them __devinitconst would cause a section type
conflict error when build for 64 bit powerpc.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
Revert "power_state: get rid of write-only variable in SATA"
make atapi_dmadir static
This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The maple bus driver that went into the kernel mainline in September 2007
contained some bugs which were revealed by the update of the kobj code
for the current release series. Unfortunately those bugs also helped
ensure maple devices were properly detected. This patch (against the
current git) now ensures that devices are properly detected again.
(A previous attempt to fix this by delaying initialisation only partially
fixed this - as became apparent when the bus was fully loaded)
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix an off-by-one spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Adrian Bunk pointed out that a Coverity scan found some apparently
dead code in nes_verbs.c that really shouldn't have been dead.
The function nes_create_cq() was missing the assignment
err = 1;
just prior to an iteration that conditionally set err = 0 if a PBL was
found for a given virtual CQ. I also noticed we should have been
returning -EFAULT on a couple related error paths.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A single entry (addr 0x10001000, size 0x2000) will get converted to
page address 0x10000000 with a page size of 0x4000. The code as it
stands doesn't address the single buffer case, but in fact it allows
the subsequent single-buffer special case to be eliminated entirely.
Because the mask now includes the (page adjusted) starting and ending
addresses, the general case works for the single buffer case as well.
Signed-off-by: Bryan Rosenburg <rosnbrg@us.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add the Intel ICH10 SMBus Controller DeviceID's and updates
Tolapai support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When probing i2c-pca-isa writes to legacy ioports, which crashes the kernel
if there is no device at that port.
This patch adds a check_legacy_ioport call, so probe fails gracefully
and thus prevents the oops.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on the PCA9564-platform driver, I sometimes had a glimpse at the
pxa-driver. I found some suspicious places, and this patch contains my
suggestions. Note: They are not tested, due to no hardware.
[JD: Some more fixes.]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Eric Miao <ymiao3@marvell.com>
This is a particularly nasty bug. The problem is that if any internal
ascb times out, currently we free it even though it's pending at the
sequencer. This results in the sequencer getting terminally confused
and the error message:
BUG:sequencer:dl:no ascb
Being returned when it comes back. The way to fix this is to manage
freeing the ascb from the tasklet completion routine, so that we only
free it when the sequencer actually returns it. The code is also
altered to use on stack completions and transfer variables.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Correct one use after free of the sas task
- update the reset required path to move straight to LUN reset
- make the bigger hammer actually reset something instead of just trying
to clear all the tasks.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Once the phy reset is plumbed in properly, SATA error handling fails
nastily because we change the port attached_sas_address using the WWN
field of the IDENTIFY message. This is a nice thing to do in theory,
but it really destroys hotplug because any event on the port causes an
automatic mismatch between the sas_address the phy just picked up and
the one we propagate into the port. However ugly they are, we have to
stick with the sas addresses made up by the phys and expanders.
Also does a few cosmetic changes to the way port printing is done to
make it clearer how a port is formed.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently aic94xx has no exported I_T_nexus_reset function. This is a
bit of a huge problem, since sas_ata relies on this function to
perform an ATA phy reset and also it means that if abort fails, we
really have no bigger hammer to hit everything with.
Plumb in the I_T_nexus_reset by quiescing the sequencer, sending the
correct phy reset (link for ATA and hard for SAS) and then carefully
resuming the sequencer again.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is needed by the to be added I_T reset function in aic94xx. It
needs to know the local phy so it can send a link or hard reset along
the path.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
mvsas.c picked up execute permissions. Move it back to being a plane
old file.
James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata-core: fix kernel-doc warning
sata_fsl: fix build with ATA_VERBOSE_DEBUG
[libata] ahci: AMD SB700/SB800 SATA support 64bit DMA
libata-pmp: clear hob for pmp register accesses
libata: automatically use DMADIR if drive/bridge requires it
power_state: get rid of write-only variable in SATA
pata_atiixp: Use 255 sector limit
Fix libata-core kernel-doc warning:
Warning(linux-2.6.25-rc2-git6//drivers/ata/libata-core.c:168): No description found for parameter 'ap'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes build and few warnings when ATA_VERBOSE_DEBUG
is defined:
CC drivers/ata/sata_fsl.o
drivers/ata/sata_fsl.c: In function ‘sata_fsl_fill_sg’:
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 3 has type ‘void *’
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 4 has type ‘struct prde *’
drivers/ata/sata_fsl.c: In function ‘sata_fsl_qc_issue’:
drivers/ata/sata_fsl.c:459: error: ‘csr_base’ undeclared (first use in this function)
drivers/ata/sata_fsl.c:459: error: (Each undeclared identifier is reported only once
drivers/ata/sata_fsl.c:459: error: for each function it appears in.)
drivers/ata/sata_fsl.c: In function ‘sata_fsl_freeze’:
drivers/ata/sata_fsl.c:525: error: ‘csr_base’ undeclared (first use in this function)
make[2]: *** [drivers/ata/sata_fsl.o] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SB700 SATA controller can support 64 bit DMA, the previous commit
badc234157 was added with
careless reference to SB600, which should be modified by this patch.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>> Mark Lord wrote:
>>> Tejun, I've added PMP to sata_mv, and am now trying to get it
>>> to work with a Marvell PM attached.
>>>
>>> And the behaviour I see is very bizarre.
>>>
>>> After hard+soft resets, the PM signature is found,
>>> and libata interrogates the PM registers.
>>>
>>> It successfully reads register 0, and then register 1.
>>> But all subsequent registers read out (incorrectly) as zeros.
...
This behavior has been confirmed by Marvell with a SATA analyzer.
The Marvell port-multiplier apparently likes to see clean HOB
information when accessing PMP registers.
Since sata_mv uses PIO shadow register access, this doesn't happen
automatically, as it might in a more purely FIS-based driver (eg. ahci).
One way to fix this is to flag these commands with ATA_TFLAG_LBA48,
forcing libata to write out the HOB fields with known (zero) values.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.
That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).
So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.
This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.
Original patch is from Mark Lord.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
power_state is scheduled for removal, and libata uses it in write-only
mode. Remove it.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch avoids a denial of service from an evildoer sending a
continuous stream of flow control at our adapter that is plugged
into a non-flow control enabled switch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This simplifies the 82571/2/3 family initialization a bit
and removes an initialization table no longer needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This counter is valuable to determine if the system is unable
to timely return buffers to the hardware and this counter starts
to increase well before the hardware starts to drop packets. If
users experience rx_no_buffer_count increasing, they should increase
the amount of descriptors. That will provide more buffers for the
hardware and will decrease the chance of hard drops.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix NCFGR.SPD setting on 10Mbps. This bug was introduced by
conversion to generic PHY layer in kernel 2.6.23.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix problems in LED management, so ethtool -p works correctly on Yukon-EC
and other chips. The driver was incorrectly setting the PHY LED overide bits.
Moral: read the spec sheet, not the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use register offset definition for WOLcgClr, rather than a magic
number.
This patch does not change the driver behaviour.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
[NETFILTER]: fix ebtable targets return
[IP_TUNNEL]: Don't limit the number of tunnels with generic name explicitly.
[NET]: Restore sanity wrt. print_mac().
[NEIGH]: Fix race between neighbor lookup and table's hash_rnd update.
[RTNL]: Validate hardware and broadcast address attribute for RTM_NEWLINK
tg3: ethtool phys_id default
[BNX2]: Update version to 1.7.4.
[BNX2]: Disable parallel detect on an HP blade.
[BNX2]: More 5706S link down workaround.
ssb: Fix support for PCI devices behind a SSB->PCI bridge
zd1211rw: fix sparse warnings
rtl818x: fix sparse warnings
ssb: Fix pcicore cardbus mode
ssb: Make the GPIO API reentrancy safe
ssb: Fix the GPIO API
ssb: Fix watchdog access for devices without a chipcommon
ssb: Fix serial console on new bcm47xx devices
ath5k: Fix build warnings on some 64-bit platforms.
WDEV, ath5k, don't return int from bool function
WDEV: ath5k, fix lock imbalance
...
This patch fixes a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch eliminates a kernel panic with the igb driver in 2.6.25-rc2 when
running on a Intel 82575 Ethernet controller with a 1000BASE-SX PHY. The
panic does not happen with the 1000BASE-T PHY, only with a SX connection.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change all dma op invocations in gianfar.c to actually pass in the
device pointer. Currently, the value is ignored, but it will be
used going forward as we implement archdata for 32-bit powerpc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading a serie of zero from the cmos sram area do not work
well with is_valid_ether_addr(). Let's read the mac address
from the eeprom first as it seems more reliable.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9831
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The forward declarations were already marked static, make the definitions
be static as well. Fixes the sparse warnings as well.
drivers/net/tlan.c:1403:5: warning: symbol 'TLan_HandleInvalid' was not declared. Should it be static?
drivers/net/tlan.c:1435:5: warning: symbol 'TLan_HandleTxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1521:5: warning: symbol 'TLan_HandleStatOverflow' was not declared. Should it be static?
drivers/net/tlan.c:1557:5: warning: symbol 'TLan_HandleRxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1692:5: warning: symbol 'TLan_HandleDummy' was not declared. Should it be static?
drivers/net/tlan.c:1722:5: warning: symbol 'TLan_HandleTxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1770:5: warning: symbol 'TLan_HandleStatusCheck' was not declared. Should it be static?
drivers/net/tlan.c:1845:5: warning: symbol 'TLan_HandleRxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1905:6: warning: symbol 'TLan_Timer' was not declared. Should it be static?
drivers/net/tlan.c:1986:6: warning: symbol 'TLan_ResetLists' was not declared. Should it be static?
drivers/net/tlan.c:2046:6: warning: symbol 'TLan_FreeLists' was not declared. Should it be static?
drivers/net/tlan.c:2095:6: warning: symbol 'TLan_PrintDio' was not declared. Should it be static?
drivers/net/tlan.c:2130:6: warning: symbol 'TLan_PrintList' was not declared. Should it be static?
drivers/net/tlan.c:2166:6: warning: symbol 'TLan_ReadAndClearStats' was not declared. Should it be static?
drivers/net/tlan.c:2242:1: warning: symbol 'TLan_ResetAdapter' was not declared. Should it be static?
drivers/net/tlan.c:2328:1: warning: symbol 'TLan_FinishReset' was not declared. Should it be static?
drivers/net/tlan.c:2451:6: warning: symbol 'TLan_SetMac' was not declared. Should it be static?
drivers/net/tlan.c:2493:6: warning: symbol 'TLan_PhyPrint' was not declared. Should it be static?
drivers/net/tlan.c:2542:6: warning: symbol 'TLan_PhyDetect' was not declared. Should it be static?
drivers/net/tlan.c:2589:6: warning: symbol 'TLan_PhyPowerDown' was not declared. Should it be static?
drivers/net/tlan.c:2614:6: warning: symbol 'TLan_PhyPowerUp' was not declared. Should it be static?
drivers/net/tlan.c:2635:6: warning: symbol 'TLan_PhyReset' was not declared. Should it be static?
drivers/net/tlan.c:2663:6: warning: symbol 'TLan_PhyStartLink' was not declared. Should it be static?
drivers/net/tlan.c:2750:6: warning: symbol 'TLan_PhyFinishAutoNeg' was not declared. Should it be static?
drivers/net/tlan.c:2906:5: warning: symbol 'TLan_MiiReadReg' was not declared. Should it be static?
drivers/net/tlan.c:2996:6: warning: symbol 'TLan_MiiSendData' was not declared. Should it be static?
drivers/net/tlan.c:3038:6: warning: symbol 'TLan_MiiSync' was not declared. Should it be static?
drivers/net/tlan.c:3077:6: warning: symbol 'TLan_MiiWriteReg' was not declared. Should it be static?
drivers/net/tlan.c:3147:6: warning: symbol 'TLan_EeSendStart' was not declared. Should it be static?
drivers/net/tlan.c:3187:5: warning: symbol 'TLan_EeSendByte' was not declared. Should it be static?
drivers/net/tlan.c:3248:6: warning: symbol 'TLan_EeReceiveByte' was not declared. Should it be static?
drivers/net/tlan.c:3306:5: warning: symbol 'TLan_EeReadByte' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The kernel.h macro DIV_ROUND_UP performs the computation
(((n) + (d) - 1) / (d)) but is perhaps more readable.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* If ConfigBase is 0x03c0 && manfid is (0x0149,0xc1ab),
printk "use axnet_cs instead" message.
Actually, most of the card with manfid(0x0149, 0xc1ab)
use pcnet_cs driver.
* remove entry (0x021b, 0x0202)
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Suppress the warning message about the 'netcard_portlist' defined but not used.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=5839
Init sequence needs to poll phy until phy reset is complete. This is the
same problem that I fixed in 2002 in tulip driver.
Thanks to manty@manty.net for testing this patch.
Thanks to Pozsar Balazs <pozsy@uhulinux.hu> for posting/testing
a similar patch before:
http://lkml.org/lkml/2006/8/21/45
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I booted an igb kernel with the option pci=nomsi and instantly noticed
that interrupts no longer worked on my igb device. I took a look at the
interrupt initialization and quickly discovered a comment stating:
"DO NOT USE EIAME or IAME in legacy mode"
It seemed a bit odd that bits to enable IAM were being set in legacy
interrupt mode, so I dropped out the following parts and interrupts
began working fine again.
[Updated code flow and a nitpick spelling error --Auke]
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The lock acquisition in fs_ioctl() does not appear to actually be necessary,
and thus is simply removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds kdump support to the ehea driver. As the firmware doesn't free
resource handles automatically, the driver has to run an as simple as possible
free resource function in case of a crash shutdown. The function iterates over
two arrays freeing all resource handles which are stored there. The arrays are
kept up-to-date during normal runtime. The crash handler fn is triggered by the
recently introduced PPC crash shutdown reg/unreg functions.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes the following compile error caused by commit
3a2d5b7001 ("PM: Introduce
PM_EVENT_HIBERNATE callback state")
CC [M] drivers/usb/host/u132-hcd.o
drivers/usb/host/u132-hcd.c: In function ‘u132_suspend’:
drivers/usb/host/u132-hcd.c:3224: error: expected expression before ‘int’
drivers/usb/host/u132-hcd.c:3225: error: ‘ports’ undeclared (first use in this function)
...
Signed-off-by: Mirco Tischler <mt-ml@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When asked to blink LEDs the tg3 driver behaves when using:
ethtool -p ethX
The default value for data is zero, and other drivers interpret this
as blink forever (or at least a really long time). The tg3 driver
interprets this as blink once. All drivers should have the same
behaviour.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of some board issues, we need to disable parallel detect on
an HP blade. Without this patch, the link state can become stuck
when it goes into parallel detect mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches to workaround the 5706S on an HP blade were not
sufficient. The link state still does not change properly in some
cases. This patch adds polling to make it completely reliable.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the same item to a given linked list more than once is guaranteed
to break and corrupt the list. This is however what we do in dmi_scan
since commit 79da472111 ("x86: fix DMI out
of memory problems").
Given that there is absolutely no interest in saving empty OEM strings
anyway, I propose the simple and efficient fix below: we discard the empty
OEM strings altogether.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Parag Warudkar <parag.warudkar@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: drivers/video/built-in.o(.text+0x7c64a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c65d): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c679): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c699): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c69f): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3676): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3689): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36a5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36c5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36cb): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a079a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ad): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07c9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07e9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ef): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
Remove __devinitdata annotation from the variable ypan.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NBD doesn't work well with CFQ (or AS) schedulers, so let's default to
something else.
The two problems I have experienced with nbd and cfq are:
1) nbd hangs with cfq on RHEL 5 (2.6.18) -- this may well have been
fixed
There's a similar debian bug that has been filed as well:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=447638
There have been posts to nbd-general mailing list about problems with
cfq and nbd also.
2) nbd performs about 10% better (the last time I tested) with deadline
vs. cfq (the overhead of cfq doesn't provide much advantage to nbd [not
being a real disk], and you end up going through the I/O scheduler on
the nbd server anyway, so it makes sense that deadline is better with
nbd)
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we gather on-board devices from both DMI types 10 and 41, there is
a possibility that we list the same device twice. In order to not confuse
drivers, and also to save memory, make sure that we do not add duplicate
devices to the dmi_devices list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the "cmos" RTC, have /proc/driver/rtc say whether HPET based IRQ
emulation is in effect. Given the problems we've had with this particular
hardware maldesign (and the fact that most BIOS code seems not to provide
the IRQ routing needed to use the saner HPET modes), this should help
troubleshooting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a sequencing bug in spi driver pxa2xx_spi.c in which the chip select
for a transfer may be asserted before the clock polarity is set on the
interface. As a result of this bug, the clock signal may have the wrong
polarity at transfer start, so it may need to make an extra half transition
before the intended clock/data signals begin. (This probably means all
transfers are one bit out of sequence.)
This only occurs on the first transfer following a change in clock polarity
in systems using more than one more than one such polarity. The fix
assures that the clock mode is properly set before asserting chip select.
This bug was introduced in a patch merged on 2006/12/10, kernel 2.6.20.
The patch defines an additional bit in: include/asm-arm/arch-pxa/regs-ssp.h
for 2.6.25 and newer kernels but this addition must be made in:
include/asm-arm/arch-pxa/pxa-regs.h for kernels between 2.6.20 and 2.6.24,
inclusive
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atmel_spi driver does not initialize clock polarity correctly (except for
at91rm9200 CS0 channel) in some case.
The atmel_spi driver uses gpio-controlled chipselect. OTOH spi clock signal
is controlled by CSRn.CPOL bit, but this register controls clock signal
correctly only in 'real transfer' duration. At the time of cs_activate()
call, CSRn.CPOL will be initialized correctly, but the controller do not know
which channel is to be used next, so clock signal will stay at the inactive
state of last transfer. If clock polarity of new transfer and last transfer
was differ, new transfer will start with wrong clock signal state.
For example, if you started SPI MODE 2 or 3 transfer after SPI MODE 0 or 1
transfer, the clock signal state at the assertion of chipselect will be low.
Of course this will violates SPI transfer.
This patch is short term solution for this problem. It makes all CSRn.CPOL
match for the transfer before activating chipselect. For longer term, the
best fix might be to let NPCS0 stay selected permanently in MR and overwrite
CSR0 with to the new slave's settings before asserting CS.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should only return IRQ_HANDLED when we actually found something to
handle. This is important since the USART interrupt handler may be
shared with the timer interrupt on some chips.
Pointed-out-by: michael <trimarchi@gandalf.sssup.it>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following is a clean up and correction of the copyright holding
entities for the files associated with the intel iommu code.
Signed-off-by: <mgross@linux.intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current mainline, __devinit qpti_sbus_probe() still is calling __init
qpti_chain_add(). Change occurrences of __init to __devinit to fix.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert rough draft Marvell 6440 driver to a working driver.
Added support for SAS and SATA devices, hotplug, wide port, and expanders.
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
update cfaf3747ff
ACPI: ACPI Exception (): AE_NOT_FOUND, Processor Device is not present
is_processor_present is only called in the processor hotplug case,
and _STA method is mandatory at this time.
We should ignore those processors that are disabled in the MADT
and don't have _STA methods.
Because they will never exist in this system.
For the processors that don't physically exist but can be
hot plugged later, we still need this debug info.
http://bugzilla.kernel.org/show_bug.cgi?id=8570
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Minor cleanups to acpi_pci_set_power_state(): use the ACPI and PCI
state symbols to make clear that a mapping is being done between PCI
and ACPI states, instead of using magic numbers. For paranoia's sake,
report any errors. Save five bytes (x86_64) too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Make ACPI_CUSTOM_DSDT boolean config symbol a hidden and derived
value, based on the value of ACPI_CUSTOM_DSDT_FILE (string).
Only the latter is presented to the user as a config option.
This fixes problems with "make randconfig" setting ACPI_CUSTOM_DSDT
but leaving ACPI_CUSTOM_DSDT_FILE empty/blank.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure the restoration correctly restores the AR registers by
flipping the ARX register into index mode before doing anything.
Without this, some people have had the text mode restore all green.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current sas_scsi_clear_queue_lu() is wrongly checking for commands
which match the pointer to the one passed in. It should be checking for
commands which are on the same logical unit as the one passed in. Fix
this by checking target pointer and LUN for equality.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The clear nexus I_T and clear nexus I_T_L functions in the aic94xx
specify the SUSPEND_TX flag which causes the sequencer to be suspended
until it receives a RESUME_TX. Unfortunately, nothing ever sends the
resume, so the sequencer on the link is stopped forever, leading to
eventual timeouts and I/O errors.
Since clear nexus commands are only executed as part of error recovery,
it's perfectly fine to keep the sequencer running on the link ... as
soon as the recovery function is completed, we'll send it the commands
to retry.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove the now useless counting of adjacent pages from the debugging code in
to make it compile when DEBUG is set non-zero.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex_internal_copy copies an in-kernel buffer to a sg list by using
scsi_kmap_atomic_sg. Some functions calls stex_internal_copy with
sg_count in struct st_ccb, which is the value that dma_map_sg
returned. However it might be shorter than the actual number of sg
entries (if the IOMMU merged the sg entries).
scsi_kmap_atomic_sg doesn't see sg->dma_length so stex_internal_copy
should be called with the actual number of sg entries
(i.e. scsi_sg_count), because if the sg entries were merged,
stex_direct_copy wrongly think that the data length in the sg list is
shorter than the actual length.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex_direct_copy copies an in-kernel buffer to a sg list in order to
spoof some SCSI commands. stex_direct_copy calls dma_map_sg and then
stex_internal_copy with the value that dma_map_sg returned. It calls
scsi_kmap_atomic_sg to copy data.
scsi_kmap_atomic_sg doesn't see sg->dma_length so if dma_map_sg merges
sg entries, stex_internal_copy gets the smaller number of sg entries
than the acutual number, which means it wrongly think that the data
length in the sg list is shorter than the actual length.
stex_direct_copy shouldn't call dma_map_sg and it doesn't need since
this code path doesn't involve dma transfers. This patch removes
stex_direct_copy and simply calls stex_internal_copy with the actual
number of sg entries.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 3163f725a5 introduced locking in
lpfc_sli_hbqbuf_fill_hbqs, but missed unlocking on one exit.
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
the check in the residual case has an incorrect test of scsi_status
(the logic is reversed, it should be scsi_status != 0 instead of
!scsi_status. Since we checked a few lines above that scsi_status was
non-zero, just eliminate this test
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The libsas error handler has two fairly fatal bugs
1. scsi_sas_task_done calls scsi_eh_finish_cmd() too early. This
happens if the task completes after it has been aborted but before
the error handler starts up. Because scsi_eh_finish_cmd()
decrements host_failed and adds the task to the done list, the
error handler start check (host_failed == host_busy) never passes
and the eh never starts.
2. The multiple task completion paths sas_scsi_clear_queue_... all
simply delete the task from the error queue. This causes it to
disappear into the ether, since a command must be placed on the
done queue to be finished off by the error handler. This behaviour
causes the HBA to hang on pending commands.
Fix 1. by moving the SAS_TASK_STATE_ABORTED check to an exit clause at
the top of the routine and calling ->scsi_done() unconditionally (it
is a nop if the timer has fired). This keeps the task in the error
handling queue until the eh starts.
Fix 2. by making sure every task goes through task complete followed
by scsi_eh_finish_cmd().
Tested this by firing resets across a disk running a hammer test (now
it actually survives without hanging the system)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
NeilBrown