Miscellanous logic and interface fixes
- Fix lpfc_init_vfi_cmpl to check the interface type for interface type 0
before parsing the results.
- Cast uint32_t values that are multiplied to uint64_t before the
multiplication.
- Instead of "break" statement when PCI read returned error, use the goto
statement to the end of the routine after setting return value
- moved the msleep(10) to the beginning of the wait loop for checking the
SLIPort_Status register
- Added the code to follow the existing wait for SLIPort_Status register RDY,
ERR, and RN bits to be set by the port before proceeding to perform PCI
function reset.
- Do not override ulpCt_h and ulpCt_l for SLI 4 ports.
- For vport delete, call lpfc_nlp_put when the vport's vpi state is not
marked with VPI_REGISTERED.
- Added missed fields into the driver's Controller Attributes Structure
- Changed ringing EQ/CQ/RQ doorbell register to be dependent on the size
of the queue.
- Return -EACCES in issue_reset if cfg_enable_hba_reset is zero.
- Added new logging flag LOG_FCP_UNDER 0x00040000 to qualify underrun logging.
- Add a check in the fabric name display routine to display 0 if the port
state is <= FLOGI.
- Add a check to the switch statement in lpfc_decode_firmware_rev to check
for an 'X'.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix issues pertaining to SCSI/FC protocol.
- Allow frames destined to 0xFFFFFE to be processed by the driver by matching
that DID with the physical port.
- Call lpfc_sli_issue_iocb with context1 set to ndlp
- In echo command accept function, adjust memcpy to limit memcpy to 1K
- Set LPFC_SLI3_BG_ENABLED properly upon completion.
- Skip the INIT_VFI call in lpfc_register_fcf if the FCF is already
registered and go immediately to initial flogi.
- use "status" variable instead of "ret" variable to hold the return of the
fc_block_scsi_eh.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
T10 DIF Fixes
- Fix the case where the SCSI Host supplies the CRC and driver to controller
protection is on.
- Only support T10 DIF type 1. LBA always goes in ref tag and app tag is not
checked.
- Change the format of the sense data passed up to the SCSI layer to match the
Descriptor Format Sense Data found in SPC-4 sections 4.5.2.1 and 4.5.2.2.
- Fix Slip PDE implementation.
- Remove BUG() in else casein lpfc_sc_to_bg_opcodes.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.
[jejb: checkpatch.pl fixes]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Update Copyright Dates
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Instead of blocking the entire host when the port's
queueing limit is hit, we should only block the port's
target. This will allow IO to other ports to execute.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the port takes a while to transition we could exhaust
the retries when using DID_TRANSPORT_DISRUPTED. For this
case we do not want to use any of the cmd's
retries, because if the command was running then when
it got failed the retry counter was already incremented.
And if this is the first time we are seeing the command,
(it got queued because it slipped through during the race)
then it should not have its retries incremented. The
fc class will decide the correct handling later.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Make link speed not supported by port message an error message.
- Add support for new SLI failure codes add sysfs parameter to reflect the
security setting and current state.
- Add all lpfc module parameters to the /sys/modules/lpfc/parameters directory.
[jejb: fix up compile failure]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
RRQ Implementation fixes
- Added checks to prevent a call to findnode_did in clr_active_rrq
- Added the del_sync_timer call for the rrq_tmr to the stop_hba_timers routine.
- Added a check in __lpfc_set_active_rrq for the driver unloading to prevent
adding an rrq when the driver is being removed.
- Add code to scsi_iocb_cmpl to check for the remote stop and add the rrq.
- Added the same check to els retry.
- Added code to compare the source did in the els rrq to the vports did and
chose the right exchange ID.
- Initialize the start_cmd pointer to indicate when we have looped through
all of the scsi buffers.
- Remove the need for the lock around the clearing of the active bit in the
rrq.
- Added code to clean the els and fcp xri aborted list and remove the all of
the RRQs for a deleted vport.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Critical Errors:
- Correctly handle non-zero return lpfc_workq_post_event and return ENOMEM
- Save the irq level when locking the host_lock in lpfc_findnode_did
Bug Fixes:
- Adjust payload_length and request_length for sli4_config mailbox commands.
- Add the freed sgl/XRI to the tail of the list rather than to the head.
- Set the FC_VPORT_NEEDS_INIT_VPI on vport deletes and check it before
issuing a fdisc on an els retry.
- Only call lpfc_hba_init_link() if phba->cfg_suppress_link_up
is LPFC_INITIALIZE_LINK.
- Add support for SLI-4 Performance Hints
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added support for ELS RRQ command
- Add new routine lpfc_set_rrq_active() to track XRI qualifier state.
- Add new module parameter lpfc_enable_rrq to control RRQ operation.
- Add logic to ELS RRQ completion handler and xri qualifier timeout
to clear XRI qualifier state.
- Use OX_ID from XRI_ABORTED_CQE for RRQ payload.
- Tie abort and XRI_ABORTED_CQE andler to RRQ generation.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix critical errors
- Update send_scsi_event to validate pnode pointer active before copying
the wwpn information.
- Add a message, mailbox_idle, and unlock before failing SECURITY_MGMT
or AUTH_PORT mailbox commands
- Prevent spin_lock_irqsave from being called twice in a row.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fail I/Os with incomplete data that complete with SCSI Check condition.
- Complete aborted I/Os with host_scribble equal to NULL with success.
- Initialize context1 field of iocbq in the new_scsi_buf routines.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Remove unneeded Endian swap for Block Guard IOCB response
- Add a check for mailbox active before issuing the heartbeat command
- Correct heartbeat last_completion updates to avoid unneeded heartbeats
- Add Security crypto support to CONFIG_PORT mailbox command
- Add fips level and fips spec revision sysfs parameters
- Remove duplicate setting of ext_byte_len fields in lpfc_bsg_issue_mbox
- Switch call to memcpy_toio to __write32_copy to prevent unaligned 64 bit copy
- Change log message 0318 from an error to a warning as it is not an error
- Patch an incorrect call to lpfc_drain_txq on SLI-3 functions
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- BSG interface related:
- Fix node reference count if node is active
- Warn if we're overwriting an active CT context
- Discovery related:
- Clear "Ignore Reg Login" flag when purging mailbox queue
- Pay attention to return code for fc_block_scsi_eh()
- Stall device loss code if we're almost done when it fires
(we're logged in, but PRLI is outstanding)
- Bugs
- Correct DIF code for endianness issues
- Correct where we had missed points to check txq on i/o
completion/cleanup
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fixed accounting of allocated SCSI buffers when post sgl fails.
- Restrict scsi buffer allocation based on LUN count (sdev_cnt).
- Create __lpfc_sli_free_rpi that doesn't take out the hbalock.
- Modify lpfc_sli_free_rpi to call __lpfc_sli_free_rpi.
- Call __lpfc_sli_free_rpi in lpfc_cleanup_pending_mbox.
- Do not swap the strings returned in mailbox commands and do
not swap byte aligned data in VPD.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Allow enabling MSI-X intterupts with fewer vectors than requested
by looking at the return value from pci_enable_msix.
- Implemented driver PCI AER error handling routines for supporting
AER error recovering on SLI4 devices.
- Remove redundant SLI_ACTIVE checks
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fix hba_queue_depth to reflect actual available XRIs
- Add support for new SLER specific firmware status codes.
- Free SCSI buffer when iotag allocation fails.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update driver for change in T10-PI interface on adapter
- Remove Profiles.
- Add new SLI Opcodes.
- Add new PDE structures used for BlockGuard.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (69 commits)
[SCSI] scsi_transport_fc: Fix synchronization issue while deleting vport
[SCSI] bfa: Update the driver version to 2.1.2.1.
[SCSI] bfa: Remove unused header files and did some cleanup.
[SCSI] bfa: Handle SCSI IO underrun case.
[SCSI] bfa: FCS and include file changes.
[SCSI] bfa: Modified the portstats get/clear logic
[SCSI] bfa: Replace bfa_get_attr() with specific APIs
[SCSI] bfa: New portlog entries for events (FIP/FLOGI/FDISC/LOGO).
[SCSI] bfa: Rename pport to fcport in BFA FCS.
[SCSI] bfa: IOC fixes, check for IOC down condition.
[SCSI] bfa: In MSIX mode, ignore spurious RME interrupts when FCoE ports are in FW mismatch state.
[SCSI] bfa: Fix Command Queue (CPE) full condition check and ack CPE interrupt.
[SCSI] bfa: IOC recovery fix in fcmode.
[SCSI] bfa: AEN and byte alignment fixes.
[SCSI] bfa: Introduce a link notification state machine.
[SCSI] bfa: Added firmware save clear feature for BFA driver.
[SCSI] bfa: FCS authentication related changes.
[SCSI] bfa: PCI VPD, FIP and include file changes.
[SCSI] bfa: Fix to copy fpma MAC when requested by user space application.
[SCSI] bfa: RPORT state machine: direct attach mode fix.
...
- Clear LPFC_DRIVER_ABORTED on FCP command completion.
- Clear exchange busy flag when I/O is aborted and found on aborted list.
- Free sglq when XRI_ABORTED event is processed before release of IOCB.
- Only process iocb as aborted when LPFC_DRIVER_ABORTED is set.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Convert all sysfs parameters to uint instead of int.
- Add lpfc_supress_link_up parameter.
- Change link_state to writable sysfs parameter.
- Add support to be able to "up" or "down" link from link_state parameter.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add support for the INTF (Interface) PCI register.
- Add support for greater than 2 page SGLs.
- Add support for up to 32 bit BDE lengths.
- Implement the Port Capabilities Mailbox command.
- Stop checking the Minor Code in the EQE structure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Display Logical Link Speed when supported and is non-zero.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix hardware/SLI relates issues:
- Handle XB bit so that ELS XRIs are not prematurely released.
- Handle XB bit so that FCP XRIs are not prematurely released.
- Define new security SLI Commands.
- Remove unused security SLI commands
- Skip receive data size parameter check on received FLOGI.
- Added LPFC_USE_FCPWQIDX flag to iocb to force SLI layer
to submit abort WQE on same WQ as the command WQE.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some comments misspell "should" or "shouldn't"; this fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix errors relating to crashes and hangs.
- Fix crash due to list corruption while unloading driver.
- Fix panic during pci-hot-plug testing.
- Fix panic when unmapping luns.
- Fixed total_scsi_bufs counting could cause exhausted memory.
- Fixed locking issue causing hang.
- Fixed the call from lpfc_new_scsi_buf_s3 to use lpfc_release_scsi_buf_s3.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC protocol fixes.
- Fix send sequence logic to handle multi SGL IOCBs.
- Fix FDISC completion always setting VPORT state to failed.
- Ported the fix on reporting of max_vpi to uppper layer.
- Fix incorrect number of Vports allowed to be created.
- Fixed Dead FCoE port after creating vports.
- Added handling of ELS request for Reinstate Recovery Qualifier (RRQ)
- Handle unsolicited CT exchange initiator receiving CT exchange ABTS
- Migrate LUN queue depth ramp up code to scsi mid-layer.
- Made ABTS WQE go to the same WQ as the WQE to be aborted.
- Fix Vport does not rediscover after FCF goes away.
- Fixed lpfc_unreg_vfi failure after devloss timeout.
- Fixed RPI bit leak.
- Fix hbq pointer corruption during target discovery.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes the following changes:
- Fixed Panic/Hang when using polling mode for fcp commands
- Added support for Read_rev mbox bits indicating FIP mode of HBA
- Optimize performance of slow-path handling of els responses
- Add code to cleanup orphaned unsolicited receive sequences
- Fixed Devloss timeout when multiple initiators are in same zone
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch include the following fixes and changes:
- Fix crash when "error" is echoed to board_mode sysfs parameter
- Fix FCoE Parameter parsing in regions 23
- Fix driver crash when creating vport with large number of targets on SLI4
- Fix bug with npiv message being logged when it is not supported by the adapter
- Fix a potential dereferencing mailbox structure after free bug
- Fix firmware crash after vport create with high target count
- Error out requests to set board_mode to warm restart via sysfs on SLI4 HBAs
- Fix Block guard logging
- Fix a memory corruption issue during GID_FT IO prep
- Fix crash while processing unsolicited FC frames
- Fix failed to allocate XRI message is not a critical failure
- Update and fix formatting in some log messages
- Fix missing new line characters in log messages
- Removed the use of the locally defined FC transport layer related macros
- Check the rsplen in lpfc_handle_fcp_err function before using rsplen
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the duplicated code from FC LLDs to SCSI FC transport class.
Acked-by: James Smart <james.smart@emulex.com>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The checksum format is orthogonal to whether the protection information
is being passed on beyond the HBA or not. It is perfectly valid to use
a non-T10 CRC with WRITE_STRIP and READ_INSERT.
Consequently it no longer makes sense to explicitly refer to the
conversion in the protection operation. Update sd_dif and lpfc
accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Ihab Hamadi <Ihab.Hamadi@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove spaces before newlines in several log messages
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add bsg (SGIOv4) support for sending and receiving ELS, CT commands
This patch adds a new file, lpfc_bsg.c.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic79xx: make driver respect nvram for IU and QAS settings
[SCSI] don't attach ULD to Dell Universal Xport
[SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
[SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
[SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
[SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
[SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
[SCSI] qla2xxx: Resolve a performance issue in interrupt
[SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
[SCSI] nsp_cs: time_out reaches -1
[SCSI] qla2xxx: fix printk format warnings
[SCSI] ncr53c8xx: div reaches -1
[SCSI] compat: don't perform unneeded copy in sg_io code
[SCSI] zfcp: Update FC pass-through support
[SCSI] zfcp: Add FC pass-through support
[SCSI] FC Pass Thru support
Patch was originally submitted upstream on 4/21/2008:
http://marc.info/?l=linux-scsi&m=120880973719266&w=2
Somewhere, it never get merged. The patch restructures the task mgmt
routines, commonizing like behavior. Then the patch changes device
reset to LUN resets, and adds a target reset handler.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contains the following changes
- Set the CT field of FDISC to 3
- Fixed over allocation of SCSI buffers on SLI4
- Removed unused jump table entries
- Increase LPFC_WQE_DEF_COUNT to 256
- Updated FDISC context to VPI
- Fixed immediate SCSI command for LUN reset translation to WQE
- Extended mailbox handling to allow MBX_POLL commands in between async
MBQ commands
- Fixed SID used for FDISC
- Fix crash when accessing ctlregs from sysfs for SLI4 HBAs
- Fix SLI4 firmware version not being saved or displayed correctly
- Expand CQID field in WQE structure to 16 bits
- Fix post header template mailbox command timing out
- Removed FCoE PCI device ID 0x0705
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for persistent vport definitions at creation at boot time
Also includes a few misc fixes for:
- conversion to vpi name from vport slang name
- couple of small mailbox references
- some additional discovery mods
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update of copyrights on modified files
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Preps the organization of the driver so that the bottom half, which
interacts with the hardware, can share common code sequences for
attachment, detachment, initialization, teardown, etc with new hardware.
For very common code sections, which become specific to the interface
type, the driver uses an indirect function call. The function is set at
initialization. For less common sections, such as initialization, the
driver looks at the interface type and calls the routines relative to
the interface.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
8.3.1 Fixes/Changes :
- Fix incorrect byte-swapping on word 4 of IOCB (data length) which
caused LUNs to not be discovered on big-endian (e.g. PPC)
- Remove a bad cast of MBslimaddr which loses the __iomem (sparse)
- Make lpfc_debugfs_mask_disc_trc static (sparse)
- Correct misspelled word BlockGuard in lpfc_logmsg.h comment
- Replaced repeated code segment for canceling IOCBs from a list with
a function call, lpfc_sli_cancel_iocbs().
- Increased HBQ buffers to support 40KB SSC sequences.
- Added sysfs interface to update speed and topology parameter without
link bounce.
- Fixed bug with sysfs fc_host WWNs not being updated after changing
the WWNs.
- Check if the active mailbox is NULL in the beginning of the mailbox
timeout handler - fixes panic in the mailbox timeout handler while
running IO stress test
- Fixed system panic in lpfc_pci_remove_one() due to ndlp indirect
reference to phba through vport
- Removed de-reference of scsi device after call to scsi_done() to fix
panic in scsi completion path while accessing scsi device after
scsi_done is called.
- Fixed "Nodelist not empty" message when unloading the driver after
target reboot test
- Added LP2105 HBA model description
- Added code to print all 16 words of unrecognized ASYNC events
- Fixed memory leak in vport create + delete loop
- Added support for handling dual error bit from HBA
- Fixed a driver NULL pointer dereference in lpfc_sli_process_sol_iocb
- Fixed a discovery bug with FC switch reboot in lpfc_setup_disc_node
- Take NULL termintator into account when calculating available buffer space
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix lpfc_parse_bg_err()'s use of do_div(). It should be passing a 64-bit
variable as the first parameter. However, since it's only using a 32-bit
variable, it doesn't need to use do_div() at all, but can instead use the
division operator.
This deals with the following warnings:
CC drivers/scsi/lpfc/lpfc_scsi.o
drivers/scsi/lpfc/lpfc_scsi.c: In function 'lpfc_parse_bg_err':
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: comparison of distinct pointer types lacks a cast
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: right shift count >= width of type
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: passing argument 1 of '__div64_32' from incompatible pointer type
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SUGGEST_* flags in the SCSI command result have been out of fashion
for a while and we don't actually use them in the error handling.
Remove the remaining occurrences.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add SCSI data path, error handling, and debugfs code to complete
BlockGuard support.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Fix mailbox buffer leak on dump mailbox completion
- Fix mbuf leak in lpfc_pci_probe_one() SLI-2 mode error path
- Don't allocate HBQs in interrupt context
- Use correct size for FCP response buffer so that all available sense
data is copied
- Fix jiffies calculation to prevent crash when collecting statistical
data
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Avoid polling HBA Error Attention when HBA's PCI channel is offline
due to PCI EEH
- Fix handling of RSCN with non-zero event qualifiers
- Remove unnecessary sleeps during HBA initialization which slow down
driver load
- Fix internal and external loopback on FCoE HBAs
- Fix incorrect decrement of cmd_pending count in lpfc_queuecomand
error path
- Fix reporting of port busy events to management application
- Rename lpfc_adjust_queue_depth() to lpfc_rampdown_queue_depth() for
consistency with its partner lpfc_rampup_queue_depth()
- Delete redundant lpfc_cmd->start_time = jiffies assignment in
lpfc_queuecommand()
- Fix handling for ELS, mailbox and heartbeat time outs in the worker
thread by removing unnecessary checking of the work_port_events
flags.
- Fix NULL pointer dereference in lpfc_prep_els_iocb
- In lpfc_device_recov_npr_node(), move clearing of NLP_NPR_2B_DISC
flag after call to lpfc_cancel_retry_delay_tmo() to keep
targets-in-discovery count correct
- Remove lpfc_probe_one()'s call to scsi_scan_host() which could cause
concurrent SCSI scans to step on each other
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In the IOCB completion handler, always check if the node is valid
before accessing the node object. Added lpfc_initialize_node() to
initialize nodes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add kernel-doc function headers to lpfc_scsi.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rework RSCN netlink event to send entire RSCN payload
Also replaces (SCSI_NL_VID_TYPE_PCI | PCI_VENDOR_ID_EMULEX) with
LPFC_NL_VENDOR_ID
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for new sysfs attributes: lpfc_stat_data_ctrl and
lpfc_max_scsicmpl_time. The attributes control statistical reporting
of io load.
Added support for new fc vendor events for error reporting.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added new sysfs attribute lpfc_max_scsicmpl_time. Attribute, when enabled,
will control target queue depth based on I/O completion time.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Revert the target busy response in favor of the transport disrupted
response for node state transitions.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: drop rejecting hunk altered by target busy patches]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for PCI-EEH permanent-disabling a device via lpfc_pci_remove_one()
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes:
- Fix the wrong variable name used for checking node active usage status
- Fix numerous duplicate log message numbers
- Fix change KERN_WARNING messages to KERN_INFO.
- Stop sending erroneous LOGO to fabric after vport is already terminated
- Fix HBQ allocates that were kalloc'ing w/ GFP_KERNEL while holding a lock.
- Fix gcc 4.3.2 compiler warnings and a sparse warning
- Fix bugs in handling unsolicited ct event queue
- Reorder some of the initial link up checks, to remove odd VPI states.
- Correct poor VPI handling
- Add debug messages
- Expand Update_CFG mailbox definition
- Fix handling of VPD data offsets
- Reorder loopback flags
- convert to use offsetof()
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update driver for new SLI-3 features:
- interrupt enhancements
- lose adapter doorbell writes
- inlining support for FCP_Ixx cmds
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We do want to call right back into the queuecommand during the race,
so we can just use SCSI_MLQUEUE_TARGET_BUSY.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes:
- Fix bug in mbox sysfs interface that locked in EAGAIN if discovery stalled.
- Fix missing error message when npiv and loop are true when link up occurs.
- Fix panic in lpfc_scsi_cmd_iocb_cmpl: scsi_buf was NULL, but created
race conditions with other code paths.
- Fix error in sysfs mailbox structure that didn't rezero on next use.
- Add missing mempool_free() to attachment failure path
- Fix missing put of ndlp structure during driver unload.
- Fix applications unable to send mailbox commands during discovery.
- Remove unused argument (type) from function lpfc_post_buffer() API
- Fix vport name is not shown after hbacmd vportcreate.
- Remove repeated code statements.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rework of the worker thread to make it more efficient.
Make a finer-grain notfication of pending work so less time is
spent checking conditions. Also made other general cleanups.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Prior handler was only waiting for I/O on one lun to finish before
returning completion. Now, wait for all LUNs on the target.
Also performed some rudimentary cleanup while in this code.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes
- Allow WRITE_VPARAM command when the virtual port is in a stopped state
- Fixed handling of our queue depth max that was unconditionally raising
the depth on all vports, rather than just the vport affected.
- Fix race in interrupt handler for mailbox processing that did not take
out the host lock.
- Removed unused functions: find_node, findnode_rpi, and fabric_abort_flogi
- Correct misspelled word unsolicited in message 0146
- Correct HW-error 5 handling - it should not reset the adapter
- Correct handling of IOCBs, which did not null out our pCmd field before
invoking the midlayer io done function.
- Changed our maximum supported target id to 4096
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Multiple Discovery Fixes:
- Fix race on discovery due to link events coinciding with vport_delete.
- Use NLP_FABRIC state to filter out switch-based pseudo initiators that
reuse the same WWNs.
- Correct erroneous setting of DID=0 in lpfc_matchdid()
- Correct extra reference count that was in the lookup path for the
remoteid from an unsolicited ELS.
- Correct double-free bug in els abort path.
- Correct FDMI server discovery logic for switch that return a WWN of 0.
- Fix bugs in ndlp mgmt when a node changes address
- Correct bug that did not delete RSCNs for vports upon link transitions
- Fix "0216 Link event during NS query" error which pops up when vports
are swapped to different switch ports.
- Add sanity checks on ndlp structures
- Fix devloss log message to dump WWN correctly
- Hold off mgmt commands that were interferring with discovery mailbox cmds
- Remove unnecessary FC_ESTABLISH_LINK logic.
- Correct some race conditions in the worker thread, resulting in devloss:
- Clear the work_port_events field before handling the work port events
- Clear the deferred ring event before handling a deferred ring event
- Hold the hba lock when waking up the work thread
- Send an acc for the rscn even when we aren't going to handle it
- Fix locking behavior that was not properly protecting the ACTIVE flag,
thus allowing mailbox command order to shift.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct ndlp referencing issues:
- Fix ndlp kref issues due to race conditions between threads
- Fix cancel els delay retry event which missed an ndlp reference count
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Made link speed and link topology modifiable via sysfs
Make scatter gather Segment Count into a module parameter.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes:
- Fix a couple of sparse complaints
- Reset the FCP recovery flag when the node is not a FCP2 device.
- Speed up offline prep delays
- Fixed a memory leak in lpfc_mem_alloc failure path
- Fixed external loopback test.
- Fixed error code returned from the driver when HBA is over heated.
- Correct Max NPIV vport to limits read from adapter
- Add missing locks around fc_flag and FC_NEEDS_REG_VPI
- Add missing hba ids for device identification
- Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands
- Changed all temperature event messages from warning to error
- Fix reporting of link speed when link is down
- Added support for MBX_WRITE_WWN mailbox command
- Change del_timer_sync() in ISR to del_timer() in interrupt handler
- Correct instances of beXX_to_cpu() that should be cpu_to_beXX()
- Perform target flush before releasing node references on module unload
- Avoid bogus devloss_tmo messages when driver unloads
- Fix panic when HBA generates ERATT interupt
- Fix mbox race condition and a workaround on back-to-back mailbox commands
- Force NPIV off for pt2pt mode between 2 NPorts
- Stop worker thread before removing fc_host.
- Fix up discovery timeout error case due to missing clear_la
- Tighten mailbox polling code to speed up detection of fast completions
- Only allow DUMP_MEMORY if adapter offline due to overtemp errors
- Added extended error information to the log messages in chip init.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct Abort handler logic. It was unconditionally waiting a minimum
of 2 seconds rather than looking for abort completion.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch corrects the lpfc tag handling issue identified by Hannes Reinecke
http://marc.info/?l=linux-scsi@m=119270235628850&w=2
The basis for this patch originated from Hajime Kai. Thank You Hajime.
Signed-off-by: hajime-kai@soft.fujitsu.com
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It was pointed out by Boaz Harrosh <bharrosh@panasas.com> that our
8.2.2 lpfc patches revert a change to using SCSI command accessor
functions.
This patch, to be applied on top of the 8.2.2. patches, updates the
driver for the accessor functions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Fix vport ndlp ref counting errors
- Fix use after free of ndlp structure
- Use the correct flag to check for LOADING setting.
- Fix driver unload bugs (related to shost references) after link down or rscn
- Fix up HBQ initialization
- Fix port_list locking around driver unload.
- Fix references to hostdata as a phba
- Fix GFFID type offset to work correctly with big endian structure.
- Only call pci_disable_msi if the pci_enable_msi succeeded
- Fix vport_delete wait/fail if in discovery
- Put a reference on the nameservers ndlp when performing CT traffic.
- Remove unbalanced hba unlock.
- Fix up HBQ processing
- Fix lpfc debugfs discovery trace output for ELS rsp cmpl
- Send ADISC when rpi is 0
- Stop FDISC retrying forever
- Unable to retrieve correct config parameter for vport
- Fix sli_validate_fcp_iocb, sli_sum_iocb, sli_abort_iocb to be vport-aware.
- Fix index-out-of-range error in iocb. Spotted by Coverity.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rework the lpfc_printf_log() macro so that logging is enabled on a
per-vport basis. Used to be on a physical-port basis, thus logging
with large numbers of vports became a mess. Required redefinition of
the macro, and an update of every use.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Split attributes up into vport and non-vport attributes.
- Move vport specific cfg params to vport
Many of the vport-specific behaviors were still global attributes
on the physical port. Move them to the vport itself.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleans up a lot of bad behaviors that have been in this area a while
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch uses dma_map_sg with phba->pcidev->dev instead of
scsi_dma_map.
scsi_dma_map doesn't work for NPIV since fc_vport->dev isn't fully
initialized. check_addr() in arch/x86_64/kernel/pci-nommu.c leads to
the crash since dev->dma_mask is NULL.
For more details:
http://marc.info/?l=linux-scsi&m=118312448030633&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is an addendum to:
commit a0b4f78f9a
Author: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[SCSI] lpfc: convert to use the data buffer accessors
One place was missed in the merge
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is a reworked version of the data buffer accessors patch
so that it applies on the NPIV sources.
The original patch was developed and submitted by Fujita Tomonori:
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
http://marc.info/?l=linux-scsi&m=117896446832171&w=2
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following the NPIV support, the following changes have been accumulated
in the testing and qualification of the driver:
- Fix affinity of ELS ring to slow/deferred event processing
- Fix Ring attention masks
- Defer dev_loss_tmo timeout handling to worker thread
- Consolidate link down error classification for better error checking
- Remove unused/deprecated nlp_initiator_tmr timer
- Fix for async scan - move adapter init code back into pci_probe_one
context. Fix async scan interfaces.
- Expand validation of ability to create vports
- Extract VPI resource cnt from firmware
- Tuning of Login/Reject policies to better deal with overwhelmned targets
- Misc ELS and discovery fixes
- Export the npiv_enable attribute to sysfs
- Mailbox handling fix
- Add debugfs support
- A few other small misc fixes:
- wrong return values, double-frees, bad locking
- Added adapter failure heartbeat
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NPIV support is added to the driver. It utilizes the interfaces of
the fc transport for the creation and deletion of vports. Within the
driver, a new Scsi_Host is created for each NPIV instance, and is
paired with a new instance of a FC port. This allows N FC Port
elements to share a single Adapter.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Smart