Update to the PowerPC PCI error recovery code.
Add code to enable MMIO if a device driver reports that it is capable
of recovering on its own. One anticipated use of this having a device
driver enable MMIO so that it can take a register dump, which might
then be followed by the device driver requesting a full reset.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add wrapper around the rtas call to enable MMIO or DMA on a frozen pci
slot.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up subroutine documentation; mostly formatting changes, with
some new content.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This corrects a pci_dev get/put imbalance that can occur only in
highly unlikely situations (kmalloc failures, pci devices with
overlapping resource addresses). No actual failures seen, this was
spotted during code review.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Jakub noticed the cputable.c entry for Xilinx Virtex-4 FX was missing
a .platform value, so the AT_PLATFORM value wouldn't be set correctly.
This adds it.
Signed-off-by: Peter Bergner <bergner@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This abstracts the operations used in the bootwrapper, and defines
the operations needed for the bootwrapper to run on an OF platform.
The operations have been divided up into platform ops (platform_ops),
firmware ops (fw_ops), device tree ops (dt_ops), and console ops
(console_ops).
The proper operations will be hooked up at runtime to provide the
functionality that you need.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are various places where we want to extract an unsigned long
value from a device-tree property that can be 1 or 2 cells in length.
This replaces some open-coded calculations, and one place where we
assumed without checking that properties were the length we wanted,
with a little of_read_ulong() helper.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This produces essentially the same code and will make the iSeries i/o
consolidation easier.
The count parameter is changed to long since that will produce the same
(better) code on 32 and 64 bit builds.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This fixes a compile error that only surfaces on CONFIG_SMP=n builds;
<asm/hvcall.h> seems to get pulled in through another header file for
SMP builds. This problem was introduced by the hvcall stats patch.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It seems that the occasional data corruption observed with the tg3
driver wasn't due to missing barriers after all, but rather seems to
be due to the DART (= IOMMU) in the U4 northbridge reading stale
IOMMU table entries from memory due to a race. This fixes it by
making the CPU read the entry back from memory before using it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the writeX family of functions to have a sync instruction
before the MMIO store rather than after, because the generally expected
behaviour is that the device receiving the MMIO store can be guaranteed
to see the effects of any preceding writes to normal memory.
To preserve ordering between writeX and readX, and to preserve ordering
between preceding stores and the readX, the readX family of functions
have had an sync added before the load.
Although writeX followed by spin_unlock is not officially guaranteed
to keep the writeX inside the spin-locked region unless an mmiowb()
is used, there are currently drivers that depend on the previous
behaviour on powerpc, which was that the mmiowb wasn't actually required.
Therefore we have a per-cpu flag that is set by writeX, cleared by
__raw_spin_lock and mmiowb, and tested by __raw_spin_unlock. If it is
set, __raw_spin_unlock does a sync and clears it.
This changes both 32-bit and 64-bit readX/writeX. 32-bit already has a
sync in __raw_spin_unlock (since lwsync doesn't exist on 32-bit), and thus
doesn't need the per-cpu flag.
Tested on G5 (PPC970) and POWER5.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Export copy_4K_page() for use by modules via copy_page() (such as
CacheFiles).
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xmon does not print a backtrace per default. This is bad on systems with
USB keyboard, the most needed info about the crash is lost.
print a backtrace during the very first xmon entry.
Booting with xmon=nobt disables the autobacktrace functionality.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add instrumentation for hypervisor calls on pseries. Call statistics
include number of calls, wall time and cpu cycles (if available) and
are made available via debugfs. Instrumentation code is behind the
HCALL_STATS config option and has no impact if not enabled.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Base patch for PA6T and PA6T-1682M. This introduces the
arch/powerpc/platform/pasemi directory, together with basic
implementations for various setup.
Much of this was based on other platform code, i.e. Maple, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reduce default cacheline size on 64-bit powerpc from 128 bytes to 64.
This is the architected minimum. In most cases we'll still end up using
cache line information from the device tree, but defaults are used during
early boot and doing a few dcbst/icbi's too many there won't do any harm.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In an attempt to make it easier for a power5 optimized app to run on a
power4 or a 970 or random earlier machine, this provides emulation of
the popcntb instruction.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As part of the new irq code pseries_kexec_cpu_down() was split into a
xics and mpic version. The vpa unregister logic is now only done in the
xics routine, and although that's ok in practice (we don't have SPLPAR
machines with mpic), I'd rather have the two concepts stay separate.
So move the vpa unregister into pseries_kexec_cpu_down(), which gets called
by both the xics and mpic routines. This also gives us an obvious place to
put any new kexec-down logic needed in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Call chip->eoi(irq) to clear any pending interrupt in case of kdump
shutdown sequence. chip->end(irq) does not serve this purpose.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Take default arch/*/kernel/audit.c to lib/, have those with special
needs (== biarch) define AUDIT_ARCH in their Kconfig.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
New sparse caught that typo which could have caused erratic hardware
behaviour on some machines if the platform functions are used by the
firmware to change bits in some FCR registers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The port to genirq & the new powerpc interrupt model in 2.6.18 introduced a
bug in the legacy PowerMac PIC code (used on older machines) because of a
typo potentially causing hangs due to interrupt storms. This fixes it,
along with a performance issue causing us to do spurrious retriggers after
masking an interrupt.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix return value from memcpy
[POWERPC] iseries: Define insw et al. so libata/ide will compile
[POWERPC] Fix irq enable/disable in smp_generic_take_timebase
[POWERPC] Fix problem with time not advancing on 32-bit platforms
[POWERPC] Restore copyright notice in arch/powerpc/kernel/fpu.S
[POWERPC] Fix up ibm_architecture_vec definition
[POWERPC] Make OF irq map code detect more error cases
[POWERPC] Support for "weird" MPICs and fixup mpc7448_hpc2
[POWERPC] Fix MPIC sense codes in documentation
[POWERPC] Fix performance regression in IRQ radix tree locking
[POWERPC] Add mpc7448hpc2 device tree source file
[POWERPC] Add MPC8349E MDS device tree source file to arch/powerpc/boot/dts
[POWERPC] modify mpc83xx platforms to use new IRQ layer
[POWERPC] Adapt ipic driver to new host_ops interface, add set_irq_type to set IRQ sense
[POWERPC] back up old school ipic.[hc] to arch/ppc
[POWERPC] Use mpc8641hpcn PIC base address from dev tree.
[POWERPC] Allow MPC8641 HPCN to build with CONFIG_PCI disabled too.
[POWERPC] Fix powerpc 44x_mmu build
[POWERPC] Remove flush_dcache_all export
This fixes a hang on ppc32.
The problem was that I was comparing a 32-bit quantity with a 64-bit
quantity, and consequently time wasn't advancing. This makes us use a
64-bit quantity on all platforms, which ends up simplifying the code
since we can now get rid of the tb_last_stamp variable (which actually
fixes another bug that Ben H and I noticed while going carefully through
the code).
This works fine on my G4 tibook. Let me know how it goes on your
machines.
Acked-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out by Herbert Xu <herbert@gondor.apana.org.au>, our
memcpy implementation didn't return the destination pointer as its
return value, and there is code in the kernel that expects that.
This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Eran Ben-Avi <eranpublic@yahoo.com> pointed out that the arch/ppc version
of smp_generic_take_timebase disables interrupts on entry but exits without
restoring them. However, both it and the arch/powerpc version have another
problem, which is that they use local_irq_disable/enable rather than
local_irq_save/restore, and they are called with interrupts disabled.
This fixes both problems; it changes a return to a break in the arch/ppc
version, and changes both versions to use local_irq_save/restore.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a problem introduced in 5db9fa9593.
The last_jiffy per-cpu variable is only 32 bits on 32-bit machines, but it
was being compared with a 64-bit quantity (tb_next_jiffy), which resulted in
time not advancing.
This fixes it by changing last_jiffy to be 64 bits on all platforms. With
this, we no longer need tb_last_stamp as a 32-bit version of tb_last_jiffy,
so this gets rid of tb_last_stamp and we just use tb_last_jiffy instead.
This also fixes a bug when the boot cpu is not online, because using
tb_last_stamp could have caused the wrong timebase origin value to be used
when calculating the time of day.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This code got moved from head.S but the copyright notice on head.S didn't
get transferred with it. Noticed by Cort Dougan <cort@fsmlabs.com>.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This problem was noticed by one of the Phyp firmware folks.
Our ibm,client-architecture-support call was failing.
This corrects the vector length parameters being passed in.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device-tree bugs on js20 with some versions of SLOF were causing the
interrupt for IDE to not be parsed correctly and fail to boot. This
patch adds a bit more sanity checking to the parser to detect some of
those errors and fail instead of returning bogus information. The
powerpc PCI code can then trigger a fallback that works on those
machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a new hardware information table for mpic. This enables
the mpic code to deal with mpic controllers with different register
layouts and hardware behaviours.
This introduces CONFIG_MPIC_WEIRD. For boards with non standard mpic
controllers, select CONFIG_MPIC_WEIRD and add its hardware information
in the mpic_infos[] array.
TSI108/109 PIC takes the first index of weird hardware information
table. :) The table can be extended. The Tsi108/109 PIC looks like
standard OpenPIC but, in fact, is different in register mapping and
behavior.
The patch does not affect the behavior of standard mpic. If
CONFIG_MPIC_WEIRD is not defined, the code is essentially identical to
the current code.
[benh@kernel.crashing.org:
This patch is a slightly cleaned up version of Zang Roy's support for
the TSI108 MPIC variant. It also fixes up MPC7448_hpc2 to use the new
version of the type macros and changes the way MPIC is selected in
Kconfig to better match what is done for other system devices.
]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When reworking the powerpc irq code, I figured out that we were using
the radix tree in a racy way. As a temporary fix, I put a spinlock in
there. However, this can have a significant impact on performances. This
patch reworks that to use a smarter technique based on the fact that
what we need is in fact a rwlock with extremely rare writers (thus
optimized for the read path).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the mpc7448hpc2 device tree source file.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add MPC8349E MDS device tree source file to arch/powerpc/boot/dts
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes MPC834x MDS (formerly SYS) and ITX platform code to get IRQ data (including PCI) from the device tree, and to use the new IPIC code.
renamed defconfig (sys -> mds), left one redundant NULL assignment in mpc83xx_pcibios_fixup to keep the compiler happy.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This converts ipic code to Benh's IRQ mods. For the IPIC, IRQ sense values in the device tree equal those in include/linux/irq.h; that's 8 for low assertion (most internal IRQs on mpc83xx), and 2 for high-to-low change.
spinlocks added to [un]mask, ack operations; default handler and type now set in host_map; and redundant condition check eliminated.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas