Prefer using accessor functions so we are not dependent on the ktime_t
type.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When devm_clk_get() fails we should return the real error code
instead of always returning -ENODEV.
This allows defer probe to happen in the case the clock provider has
not been enabled by the time max2175 driver gets probed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add two new model numbers to suppress this message in kernel log:
cx23885: cx23885[0]: warning: unknown hauppauge model #121029
Add these model numbers:
* Model 121019 - WinTV-HVR4400
* Model 121029 - WinTV-HVR5500
For WinTV-HVR4400 the documentation and my hardware differ:
Documentation says it supports DVB-S/S2 and DVB-T,
but my hardware also supports DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, and the driver is only exporting the OF ID
table entries as module aliases.
So if the driver is built as module, autoload won't work since udev/kmod
won't be able to match the registered OF device with its driver module.
Before this patch:
$ modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
After this patch:
modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
alias: i2c:adv7482
alias: i2c:adv7481
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I ran into a rare build error during randconfig testing:
drivers/staging/media/imx/imx-media-capture.o: In function `capture_stop_streaming':
imx-media-capture.c:(.text+0x224): undefined reference to `vb2_buffer_done'
drivers/staging/media/imx/imx-media-capture.o: In function `imx_media_capture_device_register':
imx-media-capture.c:(.text+0xe60): undefined reference to `vb2_queue_init'
imx-media-capture.c:(.text+0xfa0): undefined reference to `vb2_dma_contig_memops'
While VIDEOBUF2_DMA_CONTIG was already selected by the camera driver,
it wasn't necessarily there with just the base driver enabled.
This moves the 'select' statement to the top-level option to make
sure it's always available.
Fixes: 64b5a49df4 ("[media] media: imx: Add Capture Device Interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dvb_usb_device_description structures are only used during a copy
operation. Therefore, declare them as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the PLP given is NO_STREAM_ID_FILTER (~0u) don't try to set that into the PLP register. Set PLP to 0 instead.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the PLP given is NO_STREAM_ID_FILTER (~0u) don't try to set that into the PLP register. Set PLP to 0 instead.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
GIT_AUTHOR_NAME=Colin King
GIT_AUTHOR_EMAIL=colin.king@canonical.com
In a previous commit, we added FE_NONE as an unknown fe_status.
Initialize variable s to FE_NONE instead of the more opaque value 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Recently added FE_NONE to the enum fe_status, so update the
documentation accordingly.
[mchehab@s-opensource.com: change description to actually
reflect what FE_NONE means: no lock of any kind]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The fe_status variable s is not initialized meaning it can have any
random garbage status. This could be problematic if fe->ops.tune is
false as s is not updated by the call to fe->ops.tune() and a
subsequent check on the change status will using a garbage value.
Fix this by adding FE_NONE to the enum fe_status and initializing
s to this.
Detected by CoverityScan, CID#112887 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do some minor editorial changes to make this chapter visually
better, and the example a little bit clearer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description of the DVBv5 API was written a long time ago,
where the API was still new, and there were not apps using it.
Now that the API is stable and used by new applications, clarify
that DVBv3 calls should not be used and why.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ATSC 3.0 uses MPEG Media Transport, with is not currently
supported. Yet, we'll need to implement it sooner or later.
So, mention about it at the specs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description of what SEC means fits well as a footnote.
That makes the need of saying that SEC is only for Satellite
when it was mentioned, as the footnote already says that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The introduction for the frontend chapter is not quite
correct:
- it tells that it supports only three types of
delivery systems, in opposite to three *groups*;
- It adds ISDB-C to the list of supported systems,
but, this is not true.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device numbering for DVB uses "M" and "N" as vars for the
number of the device, but sometimes this is printed using normal
font instead of verbatim.
While here, remove an extra space after quotation marks.
This is a minor cleanup with no changes at the text.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written !…
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This function is broken. It sets the wrong front_end to NULL. But it's
not used, so let's just delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dib9000_remove_slave_frontend() function isn't used.
I was reviewing it because my static checker claims it writes one
element beyond the end of the array. That's a false positive. What it
actually does is, if there are two or more front ends, then it prints a
debug message to say that it removed the first one, stored in
state->fe[1], and then it "removes" (scare quotes on purpose) the second
one, stored in state->fe[2]. Deleting a front end from the middle is
not really supported and breaks code like dib9000_release() which
assumes the first NULL front end marks the end of the list.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only stored in a const field of a
video_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only stored in a const field of a
video_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only stored in a const field of a
video_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used during a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are either used during a copy operation or
passed to a const argument of the function cx88_vdev_init.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When RC_CORE is a loadable module, and au0828 is built-in including
the RC support, we get a link error:
drivers/media/usb/au0828/au0828-input.o: In function `au0828_get_key_au8522':
au0828-input.c:(.text+0x474): undefined reference to `ir_raw_event_store'
drivers/media/usb/au0828/au0828-input.o: In function `au0828_rc_register':
au0828-input.c:(.text+0x7c8): undefined reference to `rc_allocate_device'
au0828-input.c:(.text+0x8f8): undefined reference to `rc_register_device'
This adds an additional dependency, similar to the one for em28xx,
to ensure the broken configuration is never used.
Fixes: 2fcfd317f6 ("[media] au0828: add support for IR on HVR-950Q")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Refactor code in order to avoid identical code for different branches.
This issue was detected with the help of Coccinelle.
Addresses-Coverity-ID: 1226795
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
platform_get_irq() may fail, so we should better check its return
value and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some CSI-2 transmitters will finish an ongoing frame whereas others will
not. Document that receiver drivers should not assume a particular
behaviour but to work in both cases.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the cab_* codepath doesn't recognize QAM_AUTO, don't announce that
it is supported when it really isn't. Fixes ie. w_scan from
unconditionally using QAM_AUTO on DVB-C scans.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer function instead of initializing timer with the
function and data fields.
Generated by: scripts/coccinelle/api/setup_timer.cocci.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewing the delta between cppcheck output of v4.9.39 and v4.9.40
stable updates, I stumbled on the new warning:
mxl111sf.c:80: (warning) Possible null pointer dereference: rbuf
Since copying state->rcvbuf into rbuf is not needed in the 'write-only'
scenario (i.e. calling mxl111sf_ctrl_msg() from mxl111sf_i2c_send_data()
or from mxl111sf_write_reg()), bypass memcpy() in this case.
Fixes: d90b336f3f ("[media] mxl111sf: Fix driver to use heap allocate buffers for USB messages")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Call mutex_unlock and free dev on failure.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If dw2102_probe() fails on dvb_usb_device_init(), then memleak occurs.
The patch adds deallocation to the error path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The demodulator supports symbol rates as low as 100Ksyms/s - the demod
setup in start() already handles such low symbol rates and reviewers
of stv0910 equipped cards even found and tested transponders with
SRs in that range. So, announce this in the fe_ops.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The buffer mode of the cxd2099 driver requires more work regarding error
handling and thus can cause issues in some cases, so disable it by default
and make that mode of operation controllable by users via a module
parameter (ie. 'modprobe cxd2099 buffermode=1' enables current behaviour).
The upstream codebase also has the buffer mode disabled by default, so
we should match this (but users still can test things out using the
modparm).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix several
drivers/media/pci/ddbridge/ddbridge-core.c: warning: symbol ... was not declared. Should it be static?
drivers/media/pci/ddbridge/ddbridge-core.c: warning: Using plain integer as NULL pointer
drivers/media/pci/ddbridge/ddbridge-io.h: warning: cast removes address space of expression
drivers/media/pci/ddbridge/ddbridge-io.h: warning: incorrect type in argument 1 (different address spaces)
at multiple places.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Brought to attention by Matthias Schwarzott <zzam@gentoo.org> by fixing
possible use-after-free faults in some demod drivers:
In ddb_input_detach(), the i2c_client is unregistered and removed before
dvb frontends are unregistered and detached. While no use-after-free issue
was observed so far, there is another issue with this:
dvb->attached keeps track of the state of the input/output registration,
and the i2c_client unregistration takes place only if everything was
successful (dvb->attached == 0x31). If for some reason an error occurred
during the frontend setup, that value stays at 0x20. In the following
error handling and cleanup, ddb_input_detach() will skip down to that
state, leaving the i2c_client registered, causing refcount issues.
Fix this by moving the i2c_client deregistration down to case 0x20.
Cc: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Whenever write_reg() fails to open/close the demod's I2C gate, release the
lock to avoid deadlocking situations. If I2c gate open failed, there's no
need to hold a lock, and if close fails, the mutex_unlock() at the end of
the function is never reached, leaving the mutex_lock in locked state,
which in turn will cause potential for deadlocks. Thus, release the lock
on failure.
While we're touching gate_ctrl(), add some explanation about the need for
locking and the shared I2C bus/gate.
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Calling i2c_unregister_device for a demod driver destroys the frontend object.
Later it is accessed by calling dvb_unregister_frontend and
dvb_frontend_detach.
In some cases this leads to a general protection fault with this
callstack:
dvb_unregister_frontend+0x25/0x50 [dvb_core]
dvb_fini+0xdb/0x160 [cx231xx_dvb]
cx231xx_unregister_extension+0x3d/0xb0 [cx231xx]
cx231xx_dvb_unregister+0x10/0x809 [cx231xx_dvb]
SyS_delete_module+0x18a/0x240
? exit_to_usermode_loop+0x7b/0x80
entry_SYSCALL_64_fastpath+0x17/0x98
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These clamp_t() calls are no-ops because we don't save the results. It
leads to an array out of bounds bug.
Fixes: a49d25364d ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already includes
a copy of the GPL.
remove the unnecessary paragraph
Signed-off-by: Harold Gomez <haroldgmz11@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Making some functions 'static' has uncovered a few functions that
have no caller, through the gcc warnings:
atomisp/i2c/imx/imx.c:1111:12: error: 'imx_t_focus_vcm' defined but not used [-Werror=unused-function]
atomisp/i2c/imx/imx.c:1103:12: error: 'imx_vcm_init' defined but not used [-Werror=unused-function]
atomisp/i2c/imx/imx.c:1095:12: error: 'imx_vcm_power_down' defined but not used [-Werror=unused-function]
atomisp/i2c/imx/imx.c:1087:12: error: 'imx_vcm_power_up' defined but not used [-Werror=unused-function]
All four of these can be removed. Since they call indirect functions,
I also looked at how those are used in turn:
- The power_up/power_down callbacks are called from other functions
and are still needed.
- The t_focus_vcm callbacks pointers are completely unused and can
be removed in both imx and ov8858. Some of the handlers are called
directly and can now be marked static, the others are dummy
implemntations that we can remove.
- vcm_init is unused in imx, but dw9718_vcm_init is used in ov8858,
but is not used in imx, so that one needs to stay around. The callback
pointers in imx can be removed.
Fixes: 9a5a6911aa ("staging: imx: fix non-static declarations")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the as3645a flash controller to the DT source.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Jasmin Jessich