These error paths are used more often now after deep changes to the
clock code and pinctrl is still new for imx. So help debugging and give
clues in the boot log.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.
To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console feature's write routing is unsafe on SMP with
the startup/shutdown call.
There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()
The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.
Add a spin_lock for startup/shutdown/console_write routing.
This patch is a port from Freescale's Android kernel.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the part of the effort to enable SPARE_IRQ for imx platform,
the macro MXC_INTERNAL_IRQS will be removed. The imx serial driver
has a references to it for a decision on flags of request_irq call
based on rtsirq is beyond MXC_INTERNAL_IRQS. However the searching
on imx platform code tells that rtsirq will never be beyond
MXC_INTERNAL_IRQS. That said, the check, consequently the reference
to MXC_INTERNAL_IRQS are not needed, so remove them.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
This is only cosmetic for now. In case that
http://mid.gmane.org/1335171381-24869-1-git-send-email-u.kleine-koenig@pengutronix.de
will be applied, it fixes a warning
drivers/tty/serial/imx.c: In function 'serial_imx_probe_dt':
drivers/tty/serial/imx.c:1430:17: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
though.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
del_timer_sync() acquires its own lock and doesn't have to be nested
within the spinlock of sport->port.lock in imx_set_termios(), which
will cause potential deadlock. Fix this by moving it outside.
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These methods are invoked if the iMX uart is used in conjuction with kgdb during
early boot. In order to access the UART without the interrupts, the kernel uses
the basic polling methods for IO with the device. With these methods
implemented, it is now possible to enable kgdb during early boot over serial.
Signed-off-by: Saleem Abdulrasool <compnerd@compnerd.org>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
CC: linux-serial@vger.kernel.org
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Factor out the uart save/restore functionality instead of
having the same code several times in the driver.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
CC: Saleem Abdulrasool <compnerd@compnerd.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
CC: linux-serial@vger.kernel.org
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the uart device is instantiated by dt but dt doesn't provide an
alias then better let probing fail instead of falling back to an
unrelated device id used for the line number and no platform data.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A quick look at of_alias_get_id shows that in the error case it returns
-ENODEV, too, but still it's better style to propagate the value as is.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Jason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow UART to be a source for wakeup from low power mode.
Tested on a MX27PDK by doing:
echo enabled > /sys/devices/platform/imx21-uart.0/tty/ttymxc0/power/wakeup
echo mem > /sys/power/state
and then pressing a key in the console will wakeup the sytem.
Suggested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As of_alias_get_id() gets fixed and ready for use, the patch adds the
of_alias_get_id() reference back to imx serial driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[grant.likely: changed pr_err() to dev_err(), dropped unnecessary else]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The imx UART hardware controller can identify BREAK character and the
imx_set_termios() can accept BRKINT set by users, but current existing
imx_rxint() can't pass BREAK character and TTY_BREAK to the tty layer
as other serial drivers do (8250.c omap_serial.c).
Here add code to handle BREAK character and pass it to tty layer.
To detect error occurrence, i use URXD_ERR to replace (URXD_OVRRUN |
URXD_FRMERR | ...) because any kind of error occurs, URXD_ERR will
always be set to 1.
I put the URXD_BRK to the first place to check since when BREAK error
occurs, not only URXD_BRK is set to 1, but also URXD_PRERR and
URXD_FRMERR are all set to 1. This arrangement can filter out fake
parity and frame errors when BREAK error occurs.
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
of_alias_get_id() is broken and being reverted. Remove the reference
to it and replace with a single incrementing id number.
There is no risk of regression here on the imx driver since the imx
change to use of_alias_get_id() is commit 22698aa2, "serial/imx: add
device tree probe support" which is new for v3.1, and it won't get
used unless CONFIG_OF is enabled and the board is booted using a
device tree. A single incrementing integer is sufficient for now.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
It adds device tree probe support for imx tty/serial driver.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The patch removes all the uses of cpu_is_mx1(). Instead, it uses
the .id_table of platform_driver to distinguish the uart device type,
IMX1_UART and IMX21_UART. The IMX21_UART type runs on all i.mx
except i.mx1.
A couple of !cpu_is_mx1 logic gets turned into is_imx21_uart,
as the codes wrapped there are really IMX21 type uart specific.
It also removes macro MX1_UCR3_REF25 and MX1_UCR3_REF30 which are
not used anywhere.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (48 commits)
serial: 8250_pci: add support for Cronyx Omega PCI multiserial board.
tty/serial: Fix break handling for PORT_TEGRA
tty/serial: Add explicit PORT_TEGRA type
n_tracerouter and n_tracesink ldisc additions.
Intel PTI implementaiton of MIPI 1149.7.
Kernel documentation for the PTI feature.
export kernel call get_task_comm().
tty: Remove to support serial for S5P6442
pch_phub: Support new device ML7223
8250_pci: Add support for the Digi/IBM PCIe 2-port Adapter
ASoC: Update cx20442 for TTY API change
pch_uart: Support new device ML7223 IOH
parport: Use request_muxed_region for IT87 probe and lock
tty/serial: add support for Xilinx PS UART
n_gsm: Use print_hex_dump_bytes
drivers/tty/moxa.c: Put correct tty value
TTY: tty_io, annotate locking functions
TTY: serial_core, remove superfluous set_task_state
TTY: serial_core, remove invalid test
Char: moxa, fix locking in moxa_write
...
Fix up trivial conflicts in drivers/bluetooth/hci_ldisc.c and
drivers/tty/serial/Makefile.
I did the hci_ldisc thing as an evil merge, cleaning things up.
If cts changes between reading the level at the cts input (USR1_RTSS)
and acking the irq (USR1_RTSD) the last edge doesn't generate an irq and
uart_handle_cts_change is called with a outdated value for cts.
The race was introduced by commit
ceca629 ([ARM] 2971/1: i.MX uart handle rts irq)
Reported-by: Arwed Springer <Arwed.Springer@de.trumpf.com>
Tested-by: Arwed Springer <Arwed.Springer@de.trumpf.com>
Cc: stable@kernel.org # 2.6.14+
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove invalid location line in each file header after location
moved from driver/char to driver/tty
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Uwe Kleine-König