The default phase can meet most cards' requirement, but it is not the
optimal one. In some extreme situation, the rx phase point produced by
the following tuning process will drift quite a distance.
Before tuning UHS card, this patch will set a more proper initial tx
phase point, which is calculated from statistic data, and can achieve
a much better tx signal quality.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
For some Realtek card readers, the power up sequence can only be executed
when power has been turned off fully.
So the rtsx host should not start power up sequence again when set_ios
been called if the power has been turned on.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJRKmwHAAoJEHNBYZ7TNxYMNBYP/2FZRY33nrnJ0yKeMpyfdH+C
LN+33imQudA2t86FlbAOocvcpM12oTPy+DkIbFchWhN1O4lzrqMos8/527QUm9qL
cyCnZXrbst/Ttrs3UIbfkKNhA1m4Wau/taNPJ0fWqdmZU4424O774xSOyyB8m9x/
DKuPIs6B9AfVAlS+OM8ZtviIvsJRgC6amZ0mNQZIKGHPm7vCTg6n35tP1ux7ZvJQ
4dMlgqRalV+xN9gNBnCVLOc2eSwEyxIJA2m13LTHGf72pkNvSdYrID87qTJbvXOl
Ed7PHuU3+M5bHw7ErCkbi8rmwuSuc8omNt9WK+syGLx4g7v7GceIYHNQudatdN7O
gYUWnufT6Om6y+6h9QJ5td4ZZ7i6MhfC1Ps8hJCUjiVn+cLKlEPj0KmLAhZm+6cu
wuBdCujeAFu7Z5VcaO2TBLHXXsgggnWbpoq7v6fucCNIleBe598Nu2YJAdbMc+W4
8mONN4ANslTw7CAMrL3C99Ab1WVLZenX38schgDisTkGnI8dr/JCD4OpqAnPSKql
qD5KCKRb8O4BMZpQxiFwyTzqYpmNM9RkaIykLxY5y26lgwFI+At9wh1HnhFC4Hl/
ReJ5Cnm8sH19Vgz+5zpZzzS5/aCssObdfFImIfw1wWzwk9A8EHSjAZsVUkzXiVd4
yRwz6eeO3gBMZ+v2humV
=dYdW
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
Several new models of readers use different way to select driving
capability (a necessary adjustment along with voltage change). Removing
this from device-independent rtsx_pci_sdmmc module. It will be implemented
in device-depend calls encapsulated by rtsx_pci_switch_output_voltage().
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Reviewed-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Realtek card reader supports both SD and MS card. According to the
settings of rtsx MFD driver, SD host will be probed before MS host.
If we boot/reboot Linux with SD card inserted, the resetting flow of SD
card will succeed, and the following resetting flow of MS is sure to fail.
Then MS upper-level driver will ask rtsx driver to turn power off. This
request leads to the result that the following SD commands fail and SD card
can't be accessed again.
In this commit, Realtek's SD and MS host driver will check whether the card
that upper driver requesting is the one existing in the slot. If not, Realtek's
host driver will refuse the operation to make sure the exlusive accessing
at the same time.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Different card reader has different method to switch output voltage, so
we have to use the callback function provided by MFD driver to switch
output pad voltage.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes the following build error on some architectures (parisc at least):
drivers/mmc/host/rtsx_pci_sdmmc.c: In function 'sd_normal_rw':
drivers/mmc/host/rtsx_pci_sdmmc.c:448:2: error: implicit
declaration of function 'kzalloc'
[-Werror=implicit-function-declaration]
drivers/mmc/host/rtsx_pci_sdmmc.c:448:6: warning: assignment
makes pointer from integer without a cast [enabled by default]
drivers/mmc/host/rtsx_pci_sdmmc.c:472:2: error: implicit
declaration of function 'kfree'
[-Werror=implicit-function-declaration]
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For Realtek card reader, internal regsiter SD_CFG2 should be configured
before transferring data.
The default value of SD_CFG2 is proper for writing data. But for reading
sequence, the timing is not good enough. So in some extreme circumstance,
card reader may sample the response data from the card as good even if
the data is wrong. And this will cause the bad consequence.
In the prior version, the value of this register has been calculated,
but forgotten to write back to the internal register.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Realtek PCI-E SD/MMC card host driver is used to access SD/MMC card,
with the help of Realtek PCI-E card reader MFD driver.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Wei WANG