Using bool instead of an int helps readability a bit.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MT9V032 is a parallel wide VGA sensor from Aptina (formerly Micron)
controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports binning and
cropping, and the gain, auto gain, exposure, auto exposure and test
pattern controls.
Signed-off-by: Detlev Casanova <detlev.casanova@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bits 4 and 5 on register 02 should always be set to 1.
Opera1/Bsru6/z0194a/mantis_vp1033
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Issues with Register 02 causing spurious channel locking from standby.
Should have always bits 4 & 5 written to 1.
Lower nibble not used in any current driver. Usage if necessary can be
applied through initab to mcr_reg. stv0299 not out of standby before
writing inittab.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the core-assisted locking in fsl-viu driver and switch
to .unlocked_ioctl.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
users is always read or written with core->lock held. A plain int is
simpler and faster.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mpeg_users is always read or written with core->lock held except
in mpeg_release (where it looks like a bug). A plain int is simpler
and faster.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It should not be possible to enter mpeg_open and acquire core->lock
without the blackbird driver being registered, so just error out if it
is not. This makes the code more readable and should prevent the bug
fixed by the patch "hold device lock during sub-driver initialization"
from resurfacing again.
Similarly, if we enter mpeg_release and acquire core->lock then either
the blackbird driver is registered (since open files keep it loaded)
or the sysadmin forced the driver's removal. In the latter case the
state will be inconsistent and this is worth a loud warning.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add and use a mutex to protect the cx88-mpeg device list. Previously
the BKL prevented races.
Based on work by Ben Hutchings <ben@decadent.org.uk>.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx8802_blackbird_probe makes a device node for the mpeg sub-device
before it has been added to dev->drvlist. If the device is opened
during that time, the open succeeds but request_acquire cannot be
called, so the reference count remains zero. Later, when the device
is closed, the reference count becomes negative --- uh oh.
Close the race by holding core->lock during probe and not releasing
until the device is in drvlist and initialization finished.
Previously the BKL prevented this race.
Reported-by: Andreas Huber <hobrom@gmx.at>
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Cc: stable@kernel.org
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL conversion of this driver seems to have gone wrong.
Loading the cx88-blackbird driver deadlocks.
The cause: mpeg_ops::open in the cx2388x blackbird driver acquires the
device lock and calls the sub-driver's request_acquire, which tries to
acquire the lock again. Fix it by clarifying the semantics of
request_acquire, request_release, advise_acquire, and advise_release:
now all will rely on the caller to acquire the device lock.
Based on work by Ben Hutchings <ben@decadent.org.uk>.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=31962
Reported-by: Andi Huber <hobrom@gmx.at>
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Cc: stable@kernel.org
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL conversion of this driver seems to have gone wrong. Various
uses of the sub-device and driver lists appear to be subject to race
conditions.
In particular, some functions access drvlist without a relevant lock
held, which will race against removal of drivers. Let's start with
that --- clean up by consistently protecting dev->drvlist with
dev->core->lock, noting driver functions that require the device lock
to be held or not to be held.
After this patch, there are still some races --- e.g.,
cx8802_blackbird_remove can run between the time the blackbird driver
is acquired and the time it is used in mpeg_release, and there's a
similar race in cx88_dvb_bus_ctrl. Later patches will address the
remaining known races and the deadlock noticed by Andi. This patch
just makes the semantics clearer in preparation for those later
changes.
Based on work by Ben Hutchings <ben@decadent.org.uk>.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Cc: stable@kernel.org
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enabling force_testpattern module parameter in usbvision causes kernel panic.
Things like that does not belong to the kernel anyway so the fix is easy.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Nogatech USB MicroCam PAL (NV3001P) and NTSC (NV3000N) support to
usbvision driver.
PAL version is tested, NTSC untested.
Data captured using usbsnoop, init_values are listed in the INF file along
with image dimensions, offsets and frame rates.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improve PID filtering and program register 20 correctly.
Make sure stream_on message is sent if streaming is off, otherwise
PIDs are not registered.
Move mutex outside lme2510_enable_pid.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_buffer not inside mutex lock, waiting caller can alter buffer.
Static added to lme2510_exit and lme2510_exit_int.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Gate could close after first I2C message. On stv0288 it does.
Keep 2nd and 3rd message I2C gate control alive.
Remove unnecessary gate closing in this module.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In drivers/media/dvb/siano/smsusb.c we have this code:
...
kfree(dev);
sms_info("device %p destroyed", dev);
...
at least one static analysis tool (Coverity Prevent) complains about this
as a use-after-free bug.
While it's true that we do use the pointer variable after freeing it, the
only use is to print the value of the pointer, so there's not actually any
problem here. But still, silencing the complaint is trivial by just moving
the kfree() call below the sms_info(), so why not just do it?. It doesn't
change the workings of the code in any way, but it makes the tool shut up.
The patch below also removes a rather pointless blank line.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return device errors to demuxer from on/off streamming and
pid filtering.
Please test this patch with all dvb-usb devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a couple of places where mutex_unlock() is called even
if mutex_lock_interruptible() failed. The patch fixes the issue.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoid unnecessary DVB TS 188 sized packet copying from DMA buffer into stack.
Backtrack one 188 sized packet just after some garbage bytes when possible.
This obsoletes patch https://patchwork.kernel.org/patch/118147/
Signed-off-by: Marko Ristola <marko.ristola@kolumbus.fi>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We leak the memory allocated to 'fw' (the firmware) when the variable goes
out of scope.
Fix the leak by calling release_firmware(fw) before 'fw' goes out of
scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the second memory allocation in dib9000_attach() fails, we'll leak the
memory allocated by the first.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for mmap method streaming of raw YUV video on cx18-based
hardware, in addition to the existing support for read() streaming of
raw YUV and MPEG-2 encoded video.
[simon.farnsworth@onelan.co.uk: I forward-ported this from Steven's original work,
done under contract to ONELAN. The original code is at
http://www.kernellabs.com/hg/~stoth/cx18-videobuf]
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A greatly simplified version of the PID Filter now added
back to the Driver.
The driver allows for the PID filter to be turned off.
applied after patch 683781.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register 42 bits 2,3,6 and 7 should be set to 0.
This gives difficult locking on some channels and may be compensated
for by other methods.
This affects any driver using the stv0288 frontend on the default
or earda inittab.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
stv0288 Register 42 bits 6 & 7 should be set to 0.
This is causing intermittent lock, the dvb-usb-lmedm04 driver uses
register 50 (auto fine mode) to correct for this, this register is
now returned to its default setting.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An usb_submit_urb should be atomic in a completion handler. This fixes
"BUG: scheduling while atomic" messages.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for TT S-1500 with BSBE1-D01A tuner.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems like 'adap->fe' test for NULL was meant to be before we dereference
that pointer.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Acked-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The generic_standards_cnt define is only used in one place and it's
more readable to just call ARRAY_SIZE(generic_standards) directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function returns NULL on failure so lets do that if kzalloc()
fails. There is a separate problem that the caller for this function
doesn't check for errors...
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-By: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This card has a TD18271 silicon tuner, and uses TDA8290 and LGS8G75 to
demodulate analog and digital broadcast respectively. GPIO configurations
were derived using DScaler regspy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ability to force the encoder or decoder chip was broken by commit
0ab6e1c38d in February 2009. As nobody
complained for over 2 years, I take it that these parameters were no
longer used so we can simply drop them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Tested-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note: This change is tested to compile only as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we need a bigger buffer, we reallocte a new buffer and free the old
one.
Note: This change is tested to compile only as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note: This change is tested to compile only as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise it is not obvious that vp702x_usb_in_op or vp702x_usb_out_op
will not interfere with any vp702x_usb_inout_op.
Note: This change is tested to compile only, as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sets up a buffer and a mutex protecting that buffer in
the struct vp702x_device_state.
The definition of struct vp702x_device_state is moved into the header
in order to use the buffer also in the frontend.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need a state struct for the dvb_usb_device.
In order to reduce confusion we rename the vp702x_state struct.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some whitespace, one linebreak and one unneded variable
initialization...
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Igor M. Liplianin <liplianin@tut.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the on-stack buffers for USB DMA transfers.
This is an alternative version of the patch discussed by Florian here:
http://thread.gmane.org/gmane.linux.kernel/1115695/
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently we use busy waiting to seek and tune, it can replace to
interrupt way. SI470X I2C driver supports interrupt way to week and tune
via this patch.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove DEBUG define, key debug spew off of the module's debug param that
already exists.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per hardware provided to me, the Formosa Industrial Computing eHome
Infrared Receiver, 0x147a:0xe017, has no tx capability, it is rx only.
Thanks go to Paul Rae for the hardware.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to some excellent investigative work by Douglas Clowes, it was
uncovered that the older w83667hg Nuvoton chip functions with this
driver after actually enabling the CIR function via its multi-function
chip config register. The CIR and CIR wide-band sensor enable bits are
just in a different place on this hardware, so we only poke register
0x27 on 677 hardware now, and we poke register 0x2c on the 667 now.
Reported-by: Douglas Clowes <dclowes1@optusnet.com.au>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are additional chip IDs that report a PNP ID of NTN0530, which we
were refusing to load on. Instead, lets just warn if we encounter an
unknown chip, as there's a chance it will work just fine.
Also, expand the list of known hardware to include both an earlier and a
later generation chip that this driver should function with. Douglas has
an older w83667hg variant, that with a touch more work, will be
supported by this driver, and Lutz has a newer w83677hg variant that
works without any further modifications to the driver.
Reported-by: Douglas Clowes <dclowes1@optusnet.com.au>
Reported-by: Lutz Sammer <johns98@gmx.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the newly introduced KEY_IMAGES where appropriate, and standardize
on KEY_MEDIA for media center/application launcher button (such as the
Windows logo key on the Windows Media Center Ed. remotes).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Kinect sensor is a device used by Microsoft for its Kinect project,
which is a system for controller-less Human-Computer interaction
targeted for Xbox 360.
In the Kinect device, RGBD data is captured from two distinct sensors: a
regular RGB sensor and a monochrome sensor which, with the aid of a IR
structured light, captures what is finally exposed as a depth map; so
what we have is basically a Structured-light 3D scanner.
The Kinect gspca subdriver just supports the video stream for now,
exposing the output from the RGB sensor or the unprocessed output from
the monochrome sensor; it does not deal with the processed depth stream
yet, but it allows using the sensor as a Webcam or as an IR camera (an
external source of IR light might be needed for this use).
The low level implementation is based on code from the OpenKinect
project (http://openkinect.org).
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some comments about known GPIO settings of supported board
versions.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After that Anysee I2C adapter is capable of one and two byte long
I2C addresses in case of read from I2C bus.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like it is IF route switch on IOE[0]. Set it correctly
to route signal from tuner to demod. Now it works for DVB-C too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is ZL10353, TDA10023 and TDA18212.
Tuner is inside of Samsung DNOD44CDH086A tuner module.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New models have new NXP TDA18212 silicon tuner.
Not tested yet due to lack of HW...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use board ID as base value when selecting correct hardware configuration.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Print firmware version as two digit long (change from 3 to 2).
Windows app have changed that too. First byte was hard coded as 0.
Change email list address to report non-working device to current one.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It can read more than one byte from I2C bus. Allow that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make a user visible driver version change, for the inevitable user support
questions about why newer model HVR-1600's do not work with (older
versions of) the cx18 driver.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A previous changes which added the newer model HVR-1600's and DTV support for
them, neglected to add RF analog TV for them. Fix RF analog TV for the newer
HVR-1600's which have a worldwide analog tuner assembly with a TDA18271 tuner
and TDA8295 demodulator.
Thanks go to Jeff Campbell and Mike Bradley for reproting the problem, and
also to Mike Bradley for doing a lot of the legwork to figure out the tuner
reset GPIO line, the demodulator I2C address, and that the GPIOs have to be
reinitialized after a cardtype switch.
Reported-by: Jeff Campbell <jac1dlists@gmail.com>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are still lots of 80-columns warnings and a few errors
at some tables, but changing them would require more work and
with probably not much gain.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The macro is defined as:
#define CHK_ERROR(s) if( (status = s)<0 ) break
This sucks, as makes harder to debug if something got wrong and
there are more than one level of loops. Also, violates CodingStyle.
Fixed by this simple perl script:
while (<>) { $f.=$_; };
$f=~ s,\n\#define CHK_ERROR[^\n]+\n,\n,;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s,\n(\t+)CHK_ERROR\((.*)\)\;,\n\1status = \2;\n\1if (status < 0)\n\1\tbreak;,g;
print $f;
Plus a few manual adjustments
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This file is big. It has 12000+ lines! Most of the defined stuff aren't
used anyware inside the driver, so we can just remove most of the lines
and still keep everything that have any interest for the driver.
If anyone ever need the other devices, it will be stored at git logs, so
it is easy to recover.
The diff result is impressive:
1 files changed, 1013 insertions(+), 12694 deletions(-)
rewrite drivers/media/dvb/frontends/drxd_map_firm.h (90%)
As a sideback effect, drxd driver will likely compile faster, and
checkpatch.pl can run on this file without taking (literally) hours.
The code cleanup was done using this small script:
$ for i in `perl -ne 'print "$1\n" if (m/define\s+([^\s+]+)/)' drxd_map_firm.h`; do if [ "`grep $i drivers/media/dvb/frontends/drxd*.[ch]`" != "" ] ; then echo $i; fi; done|sort|uniq >used_symbols
$ grep -f used_symbols drxd_map_firm.h >defines
And then deleting the old #define lines, replacing by "defines" file content.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Take a first cleanup pass over the sources to bring them closer to the
Linux coding style.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the PCTV 330e remote control
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the flag indicating the 330e board is not validated, based on the half
dozen users who have reported today that everything is working.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Abstract out the firmware for the drx-d so that it can be loaded by the
request_firmware() interface.
The firmware licensing permits free redistribution, and can be found here:
http://kernellabs.com/firmware/drxd
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the calls necessary to use the new drx-d driver for the PCTV 330e
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Given how PCTV has multiple products with the same model name, include the
model number in the description and #define to make it a little more clear.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx bridge strobes the reset pin on the drx-d on every ts_ctrl call.
This results in the state of the chip getting out of the sync with the
state of the driver (and hence all tuning requests after the first one fail).
Make sure the drx-d is not being held in reset, but don't actually perform a
hardware reset on the chip.
The GPIO block has been split out from the other HVR-9x0 variants to reduce
the risk of regression, although in theory they would not have any issues
since none of those cases have the frontend driver managing any internal
state.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the tuner is not actually behind an i2c gate, using the i2c gate control
function can wedge the i2c bus. Provide the ability to control on a per-board
basis whether it should be used.
Problem was noticed on the HVR-900 R2, where it resulted in the first tuning
attempt succeeding, and then all subsequent attempts to access the xc3028
being treated as failures (including the call to sleep the tuner).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide the ability for the board configuration to specify whether to insert
the RS byte into the TS interconnect to the bridge, while not required for
the ngene in fact is required for the em28xx.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the drxd to the Makefile and Kconfig
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These are the original drx-d sources, extracted from Ralph Metzler's GPL'd
ngene driver. No modifications/cleanup have yet been made. In fact, no
measures have been taken to see if the code even compiles.
Signed-off-by Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default for "verbose" is 0. Update description to match.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pci_setup_device() has saved the PCI revision in the pci_dev
struct since Linux 2.6.23. Use it.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Brazil uses 6MHz-spaced channels. So, the nyquist filter for
DVB-C should be different, otherwise, inter-channel interference
may badly affect the device, and signal may not be properly decoded.
On my tests here, without this patch, sometimes channels are seen,
but, most of the time, PID filter returns with timeout.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix issue where firmware does not release on cold reset.
Also, default firmware never cold resets in multi tuner
environment.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When queueing iso packets, the run time is dominated by the two
MMIO accesses that set the DMA context's wake bit. Because most
drivers submit packets in batches, we can save much time by
removing all but the last wakeup.
The internal kernel API is changed to require a call to
fw_iso_context_queue_flush() after a batch of queued packets.
The user space API does not change, so one call to
FW_CDEV_IOC_QUEUE_ISO must specify multiple packets to take
advantage of this optimization.
In my measurements, this patch reduces the time needed to queue
fifty skip packets from userspace to one sixth on a 2.5 GHz CPU,
or to one third at 800 MHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We do not need slab allocations anymore in order to satisfy
streaming DMA mapping constraints, thanks to commit da28947e7e
"firewire: ohci: avoid separate DMA mapping for small AT payloads".
(Besides, the slab-allocated buffers that firewire-core, firewire-sbp2,
and firedtv used to provide for 8-byte write and lock requests were
still not fully portable since they crossed cacheline boundaries or
shared a cacheline with unrelated CPU-accessed data. snd-firewire-lib
got this aspect right by using an extra kmalloc/ kfree just for the
8-byte transaction buffer.)
This change replaces kmalloc'ed lock transaction scratch buffers in
firewire-core, firedtv, and snd-firewire-lib by local stack allocations.
Perhaps the most notable result of the change is simpler locking because
there is no need to serialize usages of preallocated per-device buffers
anymore. Also, allocations and deallocations are simpler.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] ngene: Fix CI data transfer regression Fix CI data transfer regression introduced by previous cleanup.
[media] v4l: make sure drivers supply a zeroed struct v4l2_subdev
[media] Missing frontend config for LME DM04/QQBOX
[media] rc_core: avoid kernel oops when rmmod saa7134
[media] imon: add conditional locking in change_protocol
[media] rc: show RC_TYPE_OTHER in sysfs
[media] ite-cir: modular build on ppc requires delay.h include
[media] mceusb: add Dell transceiver ID
A recent patch has given individual soc-camera host drivers a possibility
to calculate .sizeimage and .bytesperline pixel format fields internally,
however, some drivers relied on the core calculating these values for
them, following a default algorithm. This patch restores the default
calculation for such drivers.
Based on initial patch by Guennadi Liakhovetski, found here:
http://www.spinics.net/lists/linux-media/msg31282.html
Except that this covers try_fmt aswell.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_subdev_* functions are meant for older V4L2 drivers that do not use
the control framework yet. These functions should not be used by subdev_do_ioctl.
Most of those backwards compatibility functions are just stubs, but commit
87a0c94ce6 actually changed the behavior of
v4l2_subdev_queryctrl, so calling that one from subdev_do_ioctl broke the
control enumeration in subdev nodes.
The fix is simply not to use those compatibility functions in v4l2-subdev.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the IR interrupt handler of cx88-input.c there's a 32-bit multiply
overflow which causes IR pulse durations to be incorrectly calculated.
This is a regression caused by commit 2997137be8.
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If v4l2_device_register_subdev() fails, the reference to the subdev
module taken by the function isn't released. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix CI data transfer regression introduced by previous cleanup.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some v4l drivers currently don't initialize their struct v4l2_subdev
with zeros, and this is a problem since some of the v4l2 code expects
this. One example is the addition of internal_ops in commit 45f6f84,
after that we are at risk of random oopses with these drivers when code
in v4l2_device_register_subdev tries to dereference sd->internal_ops->*,
as can be shown by the report at http://bugs.launchpad.net/bugs/745213
and analysis of its crash at https://lkml.org/lkml/2011/4/1/168
Use kzalloc within problematic drivers to ensure we have a zeroed struct
v4l2_subdev.
BugLink: http://bugs.launchpad.net/bugs/745213
Cc: <stable@kernel.org>
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following is a patch to avoid a kernel oops when running rmmod
saa7134 on kernel 2.6.27.1. The change is as suggested by mchehab on
irc.freenode.org
Signed-off-by: Hussam Al-Tayeb <ht990332@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon_ir_change_protocol function gets called two different ways, one
way is from rc_register_device, for initial protocol selection/setup,
and the other is via a userspace-initiated protocol change request,
either by direct sysfs prodding or by something like ir-keytable.
In the rc_register_device case, the imon context lock is already held,
but when initiated from userspace, it is not, so we must acquire it,
prior to calling send_packet, which requires that the lock is held.
Without this change, there's an easily reproduceable deadlock when
another function calls send_packet (such as either of the display write
fops) after a userspace-initiated change_protocol.
With a lock-debugging-enabled kernel, I was getting this:
[ 15.014153] =====================================
[ 15.015048] [ BUG: bad unlock balance detected! ]
[ 15.015048] -------------------------------------
[ 15.015048] ir-keytable/773 is trying to release lock (&ictx->lock) at:
[ 15.015048] [<ffffffff814c6297>] mutex_unlock+0xe/0x10
[ 15.015048] but there are no more locks to release!
[ 15.015048]
[ 15.015048] other info that might help us debug this:
[ 15.015048] 2 locks held by ir-keytable/773:
[ 15.015048] #0: (&buffer->mutex){+.+.+.}, at: [<ffffffff8119d400>] sysfs_write_file+0x3c/0x144
[ 15.015048] #1: (s_active#87){.+.+.+}, at: [<ffffffff8119d4ab>] sysfs_write_file+0xe7/0x144
[ 15.015048]
[ 15.015048] stack backtrace:
[ 15.015048] Pid: 773, comm: ir-keytable Not tainted 2.6.38.4-20.fc15.x86_64.debug #1
[ 15.015048] Call Trace:
[ 15.015048] [<ffffffff81089715>] ? print_unlock_inbalance_bug+0xca/0xd5
[ 15.015048] [<ffffffff8108b35c>] ? lock_release_non_nested+0xc1/0x263
[ 15.015048] [<ffffffff814c6297>] ? mutex_unlock+0xe/0x10
[ 15.015048] [<ffffffff814c6297>] ? mutex_unlock+0xe/0x10
[ 15.015048] [<ffffffff8108b67b>] ? lock_release+0x17d/0x1a4
[ 15.015048] [<ffffffff814c6229>] ? __mutex_unlock_slowpath+0xc5/0x125
[ 15.015048] [<ffffffff814c6297>] ? mutex_unlock+0xe/0x10
[ 15.015048] [<ffffffffa02964b6>] ? send_packet+0x1c9/0x264 [imon]
[ 15.015048] [<ffffffff8108b376>] ? lock_release_non_nested+0xdb/0x263
[ 15.015048] [<ffffffffa0296731>] ? imon_ir_change_protocol+0x126/0x15e [imon]
[ 15.015048] [<ffffffffa024a334>] ? store_protocols+0x1c3/0x286 [rc_core]
[ 15.015048] [<ffffffff81326e4e>] ? dev_attr_store+0x20/0x22
[ 15.015048] [<ffffffff8119d4cc>] ? sysfs_write_file+0x108/0x144
...
The original report that led to the investigation was the following:
[ 1679.457305] INFO: task LCDd:8460 blocked for more than 120 seconds.
[ 1679.457307] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1679.457309] LCDd D ffff88010fcd89c8 0 8460 1 0x00000000
[ 1679.457312] ffff8800d5a03b48 0000000000000082 0000000000000000 ffff8800d5a03fd8
[ 1679.457314] 00000000012dcd30 fffffffffffffffd ffff8800d5a03fd8 ffff88010fcd86f0
[ 1679.457316] ffff8800d5a03fd8 ffff8800d5a03fd8 ffff88010fcd89d0 ffff8800d5a03fd8
[ 1679.457319] Call Trace:
[ 1679.457324] [<ffffffff810ff1a5>] ? zone_statistics+0x75/0x90
[ 1679.457327] [<ffffffff810ea907>] ? get_page_from_freelist+0x3c7/0x820
[ 1679.457330] [<ffffffff813b0a49>] __mutex_lock_slowpath+0x139/0x320
[ 1679.457335] [<ffffffff813b0c41>] mutex_lock+0x11/0x30
[ 1679.457338] [<ffffffffa0d54216>] display_open+0x66/0x130 [imon]
[ 1679.457345] [<ffffffffa01d06c0>] usb_open+0x180/0x310 [usbcore]
[ 1679.457349] [<ffffffff81143b3b>] chrdev_open+0x1bb/0x2d0
[ 1679.457350] [<ffffffff8113d93d>] __dentry_open+0x10d/0x370
[ 1679.457352] [<ffffffff81143980>] ? chrdev_open+0x0/0x2d0
...
Bump the driver version here so its easier to tell if people have this
locking fix or not, and also make locking during probe easier to follow.
CC: stable@kernel.org
Reported-by: Benjamin Hodgetts <ben@xnode.org>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
q->memory entry is initialized to late, so if allocation of memory buffers
fails, the buffers might not be freed correctly (q->memory is tested in
__vb2_free_mem, which can be called before setting q->memory).
Reported-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 core assumes that driver doesn't set any buffer flags.
This is correct for buffer state flags that videobuf2 manages,
but the other flags like V4L2_BUF_FLAG_{KEY,P,B}FRAME,
V4L2_BUF_FLAG_TIMECODE and V4L2_BUF_FLAG_INPUT should be passed from or to
the driver.
Reported-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for buffer timestamps and the sequence number in
the video capture driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure the sizeimage for 3-planar color formats is
width * height * 3/2 and the bytesperline is same for each
plane in case of a multi-planar format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Protecting the color format with vb2_is_streaming() is not sufficient
as this prevents changing the format only after VIDIOC_STREAMON.
To prevent the color format reconfiguration as soon as buffers
are allocated use vb2_is_busy() instead.
Also make the videobuf queue ops structure static.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct pixel limits for the fourth FIMC entity on Exynos4 SoCs.
FIMC3 only supports the writeback input from the LCD mixer.
Also rename s5pv310 variant to exynos4 which is needed after
renaming s5pv310 series to Exynos4.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 35d9f510b6.
Quoth Jiri Slaby:
"It fixes mmap when IOMMU is used on x86 only, but breaks architectures
like ARM or PPC where virt_to_phys(dma_alloc_coherent) doesn't work.
We need there dma_mmap_coherent or similar (the trickery what
snd_pcm_default_mmap does but in some saner way). But this cannot be
done at this phase."
Requested-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Härdeman