Allow randomised ethernet address if the device does not have a valid
EEPROM or pre-set MAC address.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DM9000 revision B needs 1 ms delay after PHY power-on.
PHY must be powered on by writing 0 into register DM9000_GPR before
all other settings will change (see Davicom spec and example code).
Remember, that register DM9000_GPR was not changed by reset sequence.
Without this fix the FIFO is out of sync and sends wrong data after
sequence of "ifconfig ethX down ; ifconfig ethX up".
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dm9000_set_rx_csum and dm9000_hash_table are called from atomic context (in
dm9000_init_dm9000), and from non-atomic context (via ethtool_ops and
net_device_ops respectively). This causes a spinlock recursion BUG. Fix this by
renaming these functions to *_unlocked for the atomic context, and make the
original functions locking wrappers for use in the non-atomic context.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not as fancy as coccinelle. Checkpatch errors ignored.
Compile tested allyesconfig x86, not all files compiled.
grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Wake on LAN (WOL) reception and waking the device up from
this signal via the ethtool interface. Currently we are only supporting
the magic-packet variant of wakeup.
WOL is enabled by specifying a second interrupt resource to the driver
which indicates where the interrupt for the WOL is being signalled. This
then enables the necessary ethtool calls to leave the device in a state
to receive WOL frames when going into suspend.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro res_size in drivers/net/dm9000.c is a copy of resource_size in
linux/ioport.h. Remove the function and use resource_size instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checksum offload support for DM9000A and DM9000B chips.
v2 changes: added a local copy of ip_summed to save IO cycles in dm9000_send_packet
v3 changes: trans_start updating is removed.
Signed-off-by: Yeasah Pell <yeasah@comrex.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a locking bug in the dm9000 driver. It calls
request_irq() without setting IRQF_DISABLED ... which is
correct for handlers that support IRQ sharing, since that
behavior is not guaranteed for shared IRQs. However, its
IRQ handler then wrongly assumes that IRQs are blocked.
So the fix just uses the right spinlock primitives in the
IRQ handler.
NOTE: this is a classic example of the type of bug which
lockdep currently masks by forcibly setting IRQF_DISABLED
on IRQ handlers that did not request that flag.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Stephen Rothwell:
drivers/net/dm9000.c:1450: error: expected ')' before ';' token
drivers/net/dm9000.c:1455: error: expected ';' before '}' token
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove integer casting in the read/write IO accessors,
because Blackfin now provides those functions
Tested-by: Javier Herrero <jherrero@hvsistemas.es>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The dm9000 driver reads the chip's MAC address from the attached EEPROM. When
no EEPROM is present, or when the MAC address is invalid, it falls back to
reading the address from the chip.
This patch lets platform code set the desired MAC address through platform
data.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove magic numbers for items that we already have
defined in the register header file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently all but one user (AT91SAM9261EK) of the dm9000
driver passes their IRQ flags through the resources attached
to the platform device. This means we can remove the use
of DEFAULT_TRIGGER as the blackfin machines all seem to
have their triggers set properly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The msleep() call in the code that checks for the
EEPROM controller's busy status was missing.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The DM9000's internal PHY reports a copy of the link status
in the NSR register of the chip. Reading the status when
polling for link status is faster as it eliminates the need
to sleep, but does not print as much information.
Add an platform flag to force this behaviour, and a Kconfig
option to allow it to be forced to the faster method always.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The DM9000_NSR register contains a copy of the internal PHY's
link status which we can use to determine if the link is up
or down. This eliminates the more costly (and sleeping) PHY
read when using the DM9000's own PHY.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup the source code by moving the code around to avoid
having to declare the functions before they are used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup bits of the DM9000 driver to make the code
neater and easier to read. This is includes removing
some old definitions, re-indenting areas, etc.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the now extraneous checks in dm9000_release_board()
now that the two-resource case is removed. Also remove the
check on pdev->num_resources, as we check the return data
from platform_get_resource() to ensure we have not only
the right number but the right type of resources as well.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for both the DM9000A and DM9000B versions of
the DM9000 networking chip. This includes adding support
for the Link-Change IRQ which is used instead of polling
the PHY every 2 seconds.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The dm9000 driver accepts either 2 or 3 resources to describe the platform
devices. The 2 resources case abuses the ioresource mechanism by passing
ioremap()ed memory through the platform device resources. This patch removes
that case and converts boards that were using it to the 3 resources scheme.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
use cancel_delayed_work_sync()
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Periodically check the MII PHY status to ensure that the
network layer's link status is updated and the user informed
of any changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There was a missing newline in a dev_dbg() message. Values read
from/written into PHY registers might be for interest too, so I added
new dbg messages there.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There were missing __dev* annotations for the dm9000_probe()
and dm9000_drv_remove() functions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable network
platform drivers, to re-enable auto loading.
NOTE: didn't change drivers/net/fs_enet/fs_enet-main.c "old binding" support.
That looks problematic in the first place (it even uses the ancient "struct
device_driver" binding scheme for platform_bus!) and I suspect it will vanish
soonish when arch/powerpc rules the world. Also, drivers/net/ne.c would have
needed more thought to sort out.
[akpm@linux-foundation.org: fix sgiseeq.c]
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David S. Miller