If a driver using a custom mic detection callback has provided a table
of mic detection rates via platform data then use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use a slightly larger debounce when identifying accessory type and a
slightly smaller one when detecting buttons in response to user feedback
from large scale testing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we're not actively doing audio we don't need the microphone biases
to be regulated, noise is not important when we are not looking at the
audio signal. Save some power by putting the MICBIAS regulators into
bypass mode when not doing audio.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mostly a one to one converion. On one occasion the patch replaces a
snd_soc_read-snd_soc_write sequence with regmap_update_bits though as it helps
to keep the conversion simple.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have never really updated that version number and probably never will, so
just remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not all advertised rates are available for all sysclk frequencies. Add
additional sysclk based rate constraints.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If FLL bypass is left enabled when we disable the CODEC then the output
clock will be left running which consumes a small amount of additional
current. Only enable bypass when there is an output.
Signed-off-by: Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While we need to clean up unused single ended line outputs we don't want
to do this if the outputs are in differential mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While reading through sound/soc/codecs/wm8994.c I noticed a fair
amount of trailing whitespace. This patch gets rid of it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This ensures a clean startup of the channels, without this change some
use cases could result in issues in a small proportion of cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The Springbank module can support a range of sample rates, selected at
runtime via GPIO configuration. Allow these to be configured at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since AIF3 shares clock signals with other audio interfaces in order to
ensure it doesn't drive undesirable clocks we need to tristate it. Rather
than forcing the machine driver to do so have the driver do this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch converts multiple if conditions in to single if with "&&"s.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current DA7210 driver does support PLL mode fully. It uses fixed
value of input master clock and PLL mode is enabled and disabled based
on the sampling frequency being used for playback or recording. It also
doesn't support Sample Rate Measurement feature of DA7210 hardware.
This patch adds full support for PLL and SRM. Basically following three
modes of operation are possible for DA7210 hardware,
(1) I2S SLAVE mode with PLL bypassed
(2) I2S SLAVE mode with PLL enabled
(3) I2S Master mode with PLL enabled
This patch adds support for all three modes. Also, in case of SLAVE mode
with PLL, it supports SRM (Sample Rate Measurement) feature of the chip.
Actually this patch was submitted earlier and received some review
comments, but after that the driver got update by other patches. Because
of that, I am considering this as new patch and not versioning it based
of previous patches. This version tries to take care of all review
comments received for earlier submissions.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEbBAABAgAGBQJPi3XOAAoJEHm+PkMAQRiGnsUH9RjHwH4YFVyuP/DKtKa6zs74
wqkpT15yITQ5WWMog4JaJFFg5rJCUd8QZr7AS/HSn0ijDyZX5VU7Rcs9cMudDzNR
H/5K/AscS4fjb0HwWVqoltTWHRb9QGSwVN3+E3VCDLt9P89YJ0o3QztkkuEX5dkZ
jc7reVXTfRnCcILEa9jleOzrn+OLM3j/jAjQ2hGunl8EDLzD4b17HHPoli4jEZ/5
5ibpSVsPD+AqzN+glbXvYjVItl12D0IQos/JdOwfuZriCVWLxysSSwHZTbPCyvBZ
LHH4HR5T+XLSXbjJeNkUFHLzqU+d5gVRadIoWtJCxqxFjKbOs2YtzJ5Ai0nDiw==
=kTkC
-----END PGP SIGNATURE-----
ASoC: Merge tag 'v3.4-rc3' into for-3.5
Linux 3.4-rc3 contains a bunch of Tegra changes which are conflicting
annoyingly with the new development that's going on for Tegra so merge
it up to resolve those conflicts.
Conflicts:
sound/soc/soc-core.c
sound/soc/tegra/tegra_i2s.c
sound/soc/tegra/tegra_spdif.c
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If cs42l73_get_mclkx_coeff() returns < 0 (which it can) in
sound/soc/codecs/cs42l73.c::cs42l73_set_mclk(), then we'll be using
the (negative) return value as array index on the very next line of
code - that's bad.
Catch the negative return value and propagate it to the caller (which
checks for it) and things are a bit more sane :-)
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/soc/codecs/wm9705.c: In function 'ac97_prepare':
sound/soc/codecs/wm9705.c:251: error: 'runtime' undeclared (first use in this function)
This was caused by commit e6968a (ASoC: codecs: Remove rtd->codec usage from CODEC drivers),
which removed the 'struct snd_pcm_runtime *runtime = substream->runtime' definition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following build error:
sound/soc/codecs/ac97.c: In function 'ac97_prepare':
sound/soc/codecs/ac97.c:33: error: 'runtime' undeclared (first use in this function)
This was caused by commit e6968a (ASoC: codecs: Remove rtd->codec usage from CODEC drivers),
which removed the 'struct snd_pcm_runtime *runtime = substream->runtime' definition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following build error:
sound/soc/codecs/wm9712.c:482:32: error: 'runtime' undeclared (first use in this function)
sound/soc/codecs/wm9712.c:499:33: error: 'runtime' undeclared (first use in this function)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Later WM8994 class devices can bypass the FLL from BCLK. Do this
automatically when the FLL input and output frequencies match up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
release_firmware() does its own NULL ptr testing, it's redundant to
also test before calling it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than adding new arguments to regulator_register() every time we
want to add a new bit of dynamic information at runtime change the function
to take these via a struct. By doing this we avoid needing to do further
changes like the recent addition of device tree support which required each
regulator driver to be updated to take an additional parameter.
The regulator_desc which should (mostly) be static data is still passed
separately as most drivers are able to configure this statically at build
time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/soc/codecs/lm49453.c: In function 'lm49453_set_dai_fmt':
sound/soc/codecs/lm49453.c:1189:4: warning: overflow in implicit
constant conversion [-Woverflow]
sound/soc/codecs/lm49453.c:1193:4: warning: overflow in implicit
constant conversion [-Woverflow]
sound/soc/codecs/lm49453.c:1197:4: warning: overflow in implicit
constant conversion [-Woverflow]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ak4642 out_tlv is +12.0dB to -115.0 dB, and it supports mute.
But current settings didn't care +1 step for mute.
This patch adds it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
In order to support CODEC<->CODEC links remove the assumption that there
is only a single CODEC on a DAI link by removing the use of the CODEC
pointer in the rtd from the CODEC drivers. They are already being passed
their DAI whenever they are passed an rtd and can get the CODEC from
there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following warning during kernel boot:
0-000a: 850 <--> 1600 mV at 1200 mV normal
0-000a: Voltage range but no REGULATOR_CHANGE_VOLTAGE
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some codecs namely Cirrus Logic Codecs have a way of wrapping the dB scale around 0dB without 0dB being in the middle.
Rework of SOC_DOUBLE_R_SX_TLV to be more consistent with other asoc tlv macros.
Add single register macro : SOC_SINGLE_SX_TLV.
Use snd_soc_info_volsw for .info
Use snd_soc_get_volsw_sx, snd_soc_put_volsw_sx for single and double.
kcontrols for CS42L51 and CS42L73 are adjusted to these new TLV Macros.
The max value is determined by: (number of steps) +1 for 0dB +max from codec datasheet.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As manual described, VAG is an internal voltage reference of DAC/ADC,
So enabled it before DAC/ADC up.
One more thing should care about is VAG fully ramped down requires 400ms,
wait it to avoid pop.
Signed-off-by: Zeng Zhaoming <zengzm.kernel@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/soc/codecs/max98095.c: In function 'max98095_jack_detect_enable':
sound/soc/codecs/max98095.c:2229:14: error: 'struct max98095_priv' has no member named 'jack_detect_delay'
sound/soc/codecs/max98095.c:2230:18: error: 'struct max98095_priv' has no member named 'jack_detect_delay'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This increases the chances we'll manage to hit a partially configured
state on restart and the power savings are extremely small.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for spi regmap feature to existing da7210
driver.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No current users and it's the last user of MICBIAS_E().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Zeng Zhaoming <zengzm.kernel@gmail.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Rather than trying to work around machine drivers which try to reprogram
the FLL while it is providing SYSCLK just return an error if they try.
This will avoid audio glitches during FLL reconfiguration, or at least
move the introduction of the glitches to the machine driver.
Since disabling the source for an active SYSCLK is not supported in the
first place systems shouldn't be doing this in the first place.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ML26124-01HB/ML26124-02GD is 16bit monaural audio CODEC which has high
resistance to voltage noise. On chip regulator realizes power supply rejection
ratio be over 90dB so more than 50dB is improved than ever. ML26124-01HB/
ML26124-02GD can deliver stable audio performance without being affected by noise
from the power supply circuit and peripheral components. The chip also includes
a composite video signal output, which can be applied to various portable device
requirements. The ML26124 is realized these functions into very small package
the size is only 2.56mm x 2.46mm therefore can be construct high quality sound
system easily.
ML26124-01HB is 25pin WCSP package; ML26124-02GD is 32pin WQFN package.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's possible that the regulator enable will fail and if it does we may
as well just give up with trying to bring the rest of the device up and
report the original error.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Timur Tabi <timur@freescale.com>
We can simply use the register cache code to synchronise the current
configuration down to the device when bringing up the DSP.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change adds the logic to support using the jack detect mechanism built
in to the codec to detect both when a jack was inserted and what type of
jack is present.
This change also supports the use of an external mechanism for headphone
detection. If this mechanism exists, when the max98095_jack_detect function
is called, the hp_jack is simply passed NULL.
This change supports both simple headphones, powered headphones, microphones
and headsets with both headphones and a mic.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM now has a DAPM-level lock which it manages itself so we don't need
to take the CODEC mutex to call DAPM any more. Also remove a redundant
call to snd_soc_dapm_sync(), jack reporting also triggers a DAPM sync.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's more idiomatic to do this and it means we don't try to bring up the
card if the CODEC didn't manage to bind successfully.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A collection of small fixes for 3.4-rc1, including
- mic-recording regression fix for Realtek codec
- clean-up of dmaengine parameter mess
- WM8894 calibration tweak
- minor fixes for asihpi and some bool module parms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=cW/4
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes for 3.4-rc1, including
- mic-recording regression fix for Realtek codec
- clean-up of dmaengine parameter mess
- WM8894 calibration tweak
- minor fixes for asihpi and some bool module parms"
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fix isa/opti9xx module param type
sound: fix oss/msnd_pinnacle module param type
ALSA: asihpi - fix return type of hpios_locked_mem_alloc()
ASoC: dmaengine_pcm: use dmaengine cyclic wrapper
ASoC: Add extra parameter to device_prep_dma_cyclic
ALSA: hda/realtek - Fix ADC assignment with a shared HP/Mic pin
ASoC: wm8994: Update WM8994 DCS calibration
The cleanup of the dmaengine parameter messup and a tweak to some
callibration values for WM1811.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XZ+C
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: A few more updates for 3.4
The cleanup of the dmaengine parameter messup and a tweak to some
callibration values for WM1811.
seeing a trickle of new features coming in they're getting much smaller
than they were. It's also nice to have some features which support
other subsystems building infrastructure on top of regmap. Highlights
include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring the
register state. This is intended to be used to apply updates supplied by
manufacturers for tuning the performance of the device (many of which
are to undocumented registers which aren't otherwise covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for other
subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPYJuOAAoJEBus8iNuMP3dauMP/1mYgILz0lpRHjGmUF86vQre
AcualwUE4UY/WacyUkke72kxa9jcznwzbFjKKNSvL3rLnNy+QPY8Z9v6zBDL90or
D9Ok8nRVRldIIDlDE708b10AP9sDSB25ra9IVVPzOEX/0NKoE+Y7ZkXcn0s3zGgI
Y+bLwd1uufFopMpV3m5gXipi1/+PEK+jO7q6vgdUp3C1TcMzOqSyCg+uuHWffHGp
iO/1XzdxNGx9BTDO/XDEqxUMRnjsQg/VS9JN3CMz8gXwxXD3zrWB/9+SMIfDb5Iy
/iXqc58uJ6PTY87t5q9TEGyRKo0Xj7NEPnW4isXg/3r0UUb8kls3frXKigtLEUb7
wnwQD/GCRvXOTbC6TUkFDiZ3OX1qLmnk8YMQ6xhQlbNGM7jJfzj/fFiwBdre58BC
iKPdF9gfL/gyH5yefySau/YeYqJUbVLzdOAfYVDkjApmQJv67CrPPd96xAsEsTFU
YojkF9NcapBnk6Vs4adzjxD1YCTThaXnFtUSu/bBNZu1xNFD12TORl5fs0OedUe8
zvPMZEEKrE5CxHhQNB6j2Z0zajNOgsh183mNSr2VJK1vI4o4pY7MBENYYPzFiPB4
BfX8KFftxu8O50OVZnweZ80LKVZ9fAo57oWlgR8lfaEbetjY0WdRYOyDT8w5jrtW
nU+mtlQLc5SmugTs+CiD
=4Eo9
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Things are really quieting down with the regmap API, while we're still
seeing a trickle of new features coming in they're getting much
smaller than they were. It's also nice to have some features which
support other subsystems building infrastructure on top of regmap.
Highlights include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring
the register state. This is intended to be used to apply updates
supplied by manufacturers for tuning the performance of the device
(many of which are to undocumented registers which aren't otherwise
covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for
other subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (41 commits)
regmap: Fix future missing prototype of devres_alloc() and friends
regmap: Rejig struct declarations for stubbed API
regmap: Fix rbtree block base in sync
regcache: Make sure we sync register 0 in an rbtree cache
regmap: delete unused module.h from drivers/base/regmap files
regmap: Add stub for regcache_sync_region()
mfd: Improve performance of later WM1811 revisions
regmap: Fix x86_64 breakage
regmap: Allow drivers to sync only part of the register cache
regmap: Supply ranges to the sync operations
regmap: Add tracepoints for cache only and cache bypass
regmap: Mark the cache as clean after a successful sync
regmap: Remove default cache sync implementation
regmap: Skip hardware defaults for LZO caches
regmap: Expose the driver name in debugfs
mfd: wm8400: Convert to devm_regmap_init_i2c()
mfd: wm831x: Convert to devm_regmap_init()
mfd: wm8994: Convert to devm_regmap_init()
mfd/ASoC: Convert WM8994 driver to use regmap patches
mfd: Add __devinit and __devexit annotations in wm8994
...
There's a couple of small features here that were added late on but have
been in -next in my tree and some bug fixes. The wm_hubs stuff is
actually bug fixes - the stuff that's currently in 3.4 is a half way
house between the two solutions that the latest change allows the
machine to select between.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K2Tm
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
Last minute ASoC updates for 3.4
There's a couple of small features here that were added late on but have
been in -next in my tree and some bug fixes. The wm_hubs stuff is
actually bug fixes - the stuff that's currently in 3.4 is a half way
house between the two solutions that the latest change allows the
machine to select between.
The optimal management of VMID depends on a number of factors which vary
dynamically at runtime, for example the connection to a system docking
station. In some circumstances it is desirable to keep VMID enabled all
the time, in others it is desirable to aggressively power it up and down.
Provide a callback allowing machine driver to configure either the normal
power up/down mode (WM8994_VMID_MODE_NORMAL) or to maintain VMID even
when idle (WM8994_VMID_MODE_FORCE). This callback, wm8994_vmid_mode(),
should be called with the CODEC lock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8996 specification has been updated to specify 44.1kHz as a supported
sample rate. Update the driver to accept this configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently we can the accdet mutex from within DAPM when updating the device
state which means we take accdet then the CODEC mutex but we also do the
locking the other way around when responding to the jackdet IRQ. Move all
the jackdet use of the CODEC mutex out of the accdet lock to avoid this.
Since all the DAPM interactions depend only on a single threaded IRQ this
is still serialised.
The locking improvements in 3.5 allow a better solution there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch removes following registers from reg map defaults,
- Registers which are currently not used by driver
- Non existing registers
- Volatile registers
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current DA7210 driver has I2C support using older register cache
methods. This patch updates it for latest regmap framework.
This has been tested on DA7210 EVB with Samsung SMDK6410 board.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
from arch/arm into sound/soc. There's also some general driver specific
tweaks and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0lYr
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
A few more ASoC updates, the main one is the move of the audmux driver
from arch/arm into sound/soc. There's also some general driver specific
tweaks and fixes.
commit 891271c "ASoC: Convert wm8804 to direct regmap API usage"
only converts wm8804_spi_probe to use regmap_init_spi.
This patch adds missing regmap_init_i2c in wm8804_i2c_probe.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we are out of system sleep always use audio mode for jack detection
in order to avoid potential performance issues handing off between modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FpJH
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
This has been a very active release for ASoC, as well as the usual raft
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
Without that fix the wm8753 SPI initialization fails, and then produces
a kernel panic during boot with the following call trace:
Unable to handle kernel paging request at virtual address 37386d9b
[<c01ccafc>] (regmap_get_val_bytes+0x0/0x14) from [<c0243dfc>] (snd_soc_codec_set_cache_io+0x9c/0xcc)
[<c0243dfc>] (snd_soc_codec_set_cache_io+0x9c/0xcc) from [<c0244a4c>] (wm8753_probe+0x5c/0x1c4)
[<c0244a4c>] (wm8753_probe+0x5c/0x1c4) from [<c023bb24>] (soc_probe_codec+0x174/0x284)
[<c023bb24>] (soc_probe_codec+0x174/0x284) from [<c023c2c0>] (snd_soc_instantiate_cards+0x68c/0xe28)
[<c023c2c0>] (snd_soc_instantiate_cards+0x68c/0xe28) from [<c023d278>] (snd_soc_register_card+0x240/0x2d4)
[<c023d278>] (snd_soc_register_card+0x240/0x2d4) from [<c023d330>] (soc_probe+0x24/0x40)
[<c023d330>] (soc_probe+0x24/0x40) from [<c01c3900>] (platform_drv_probe+0x14/0x18)
[...]
The commit d3398ff059
( ASoC: Convert WM8753 to direct regmap API usage ) introduced
the problem.
Thanks to Lars-Peter Clausen for helping me a bit during the debugging.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Push everything through one function for active use cases, should be
no practical effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Normally this will have no effect as we set detection up at system startup
before DAPM syncs take effect, this will only be useful if the system
enables and disables detection at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811 DC servo is able to run much faster than previous devices so
the benefit of skipping calibration is not useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using snd_soc_write() means we always write to the register even if it
already contains the newly calculated value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Similar to what commit 1e3ad57 (ASoC: Remove redundant -codec from
WM8776 driver name) does for wm8776 driver, this patch does the same
thing for cs4270 driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the cache is currently open coded this is more of a win than for
most devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Don't use the internal I/O functions directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Early revisions of several of the WM8994 variants have register updates
to improve performance. Move these over to using the regmap patch system
instead of open coding them in the audio driver. Since the regmap init
is done by the MFD the code is moved there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
When an external capacitor is connected to MICBIAS2 on devices with
jack detection (which is not required but may be done in some systems)
then the loading may mean that better performance is obtained when
the microphone bias is enabled normally rather than using the low power
mode. Provide platform data allowing systems to indicate if they require
this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This minimises the chance of any external capacitors that are fitted
being discharged into headphones as they insert.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current ak4642 driver had wrong dapm settings for headphone L/R.
If you select headphone L, and select R after that,
headphone L setting was removed by R settings.
This patch fixes it up.
It provides just "Headphone Enable" to user side
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the printk(KERN_ERR* instances with dev_err in the driver.
While we are here clean up some of the debug messages as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8775 is register compatible with the WM8776 so can be supported with
the same driver though it is an ADC only part. Add the device ID to the
WM8776 driver, further updates will be added in the future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While it matches the current code only bringing the device out of reset
isn't actually doing what the function says so make sure we set the GPIO
high before we pull it low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows userspace control of final power off, allowing policy decisions
for register configuration retention.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only enable and disable the FLL when explicitly told to, supporting some
additional use cases and making the driver behaviour more standard.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we update for any changes in cases where we reconfigure while
live (eg, for analogue bypass).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Show the id we read when the id mismatch is detected.
This is useful for debugging.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The main role of the WM9081 is as a class D speaker amplifier so there
is no concern about pops. There are also very few registers and a fast
power up time so we can happily mark the driver as idle_bias_off.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Raise the ramp time to 50ms to cover corner cases, use the startup bias
generator, explicitly reset the ramp circuit when complete and reorder
things all of which should improve performance somewhat for systems that
are sensitive to noise from VMID.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The enable of the single ended line outputs on wm_hubs devices performs
better if the output is enabled prior to starting VMID. Since inactive
outputs are held at VMID anyway there is little cost to doing this for
unused outputs. Add callbacks into wm_hubs and keep track of which outputs
are really active so we can disable them once we're active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the mixer path diagram input sources' attenuators logically
belong to the playback path and DMIC boost only affects capture.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This brings the TLVs in sync with the documentation and allows to properly
manipulate mic boost controls with alsamixer.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch should fix output through speakers using HP mixer.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix I2S digital interface power for recording.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DMIC switches and controls to ALC5632 codec.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no Phone Mix<->Mono Mix route in datasheet.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename capture switches to common scheme XXX2REC.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove extra zero from volume step in DECLARE_TLV_DB_SCALE macro.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct spelling "memroy" to "memory" in
sound/soc/codecs/twl4030.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. the number of the half-beast?
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPMzv8AAoJEHm+PkMAQRiGgeYIAJxxGCxSMLRIiPaGRmQbWifs
eE3z6AUWitGfYvhmYdWVz+C/aa4pPCVWr3bAFxUQhu+ESmiFIiqiefvlTRf5f84e
pcoJFobkFfhtK4gLvUr75WxXDFq/1HhKqW1OLzIW4gQsnhMdjGJ3lLK6ZoRYH8h4
cGoN3DRII9mVLFcB2sgbeRvbQBA/O4n0aOQ2ryZkCcPQQMIKhR/rUEEV2pe/ovHE
rumQgI3PVey816P4e5YnOvrEAllFZlaZ/F0ClJgNdfeQCVTZx9KNRbiNxHi6fcC5
6Zgg7e5EvQTAy7QqQZ0hmS4k4CFmnswX3Nm+ZabRNqBdLSjPEDD9hk1o1dodYCg=
=BBLC
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc3' as we've got several bugfixes in there which are
colliding annoyingly with development.
Linux 3.3-rc3
.. the number of the half-beast?
Conflicts:
sound/soc/codecs/wm5100.c
sound/soc/codecs/wm8994.c
It's set unconditionally.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The VMID ramp rate is supposed to be 0x3, not 11b. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Make sure we generate enough BCLKs for I2S style modes by always having
a minimum of two channels worth of clocks for the BCLK.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No practical impact but now we have the control type we may as well use
it for the slightly nicer sequencing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we're not implementing GPIO or microphone detection support
there's no users for the read() function any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Make the mechanism used for WM8994 more like that for WM1811 and WM8958:
provide the logic to distinguish between headphone and headset and hard
code the reporting of sensible SND_JACK values. Should integration with
other detection mechanisms be required we can add appropriate callbacks
(though some integrations should be able to use the subsystem ones).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we might get an error if the GPIO is configured as an input
since that makes the register volatile and a suspended device can't be
read from.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the default state that the runtime PM infrastructure expects so
instead just kick the runtime PM core to suspend us if we're not doing
anything (as is default).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix build breakage by using the correct API call to add kcontrols.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Looks like nobody is or will be using this code.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In cases where we should enter STANDBY DAPM will power us up, otherwise
there is no need to power up and we can remain in OFF.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can enable VMID independently of the bias in some use cases so we need
to ensure that the core device is powered up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The second line output mixer has the controls for the line input bypasses
in the opposite order.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
For master mode, set Output [X|A|V]SP_SCLK Sourcing Mode to MCLK Mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into for-3.4
A reasonable amount of new development is causing fiddly merge conflicts
between different resource management changes (mostly fixing bugs in
resource management due to noticing things while doing enhancements in
the same area).
Linux 3.3-rc2
.. several days delayed. No reason, I just didn't think of it.
For later wm_hubs devices we have much less need to keep the biases up
even when using single ended line outputs so flag idle_bias_off for
everything except the WM8993 and WM8994.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now we've switched over to regmap the ASoC level cache sync will be
ineffectual and potentially harmful as there is no longer an ASoC level
cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
IN1L/R is routed to both line output mixers, we don't route IN1 to LINEOUT1
and IN2 to LINEOUT2.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The Mute Switch should be called Playback Switch to match the volume
and the regmap core has been updated so we don't need to mark all the
registers as non-volatile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For optimal performance the single ended line outputs require that the
line output VMID buffer be enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Report any accessory with a low impedance as a headphone, previously
anything other than a short or microphone would not be reported at all.
The most likely reason is a microphone with incorrect polarity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using pm_runtime to decide if the device should go into full power down
has the dual advantage of allowing easier integration with non-DAPM
reasons to power on the device (like the FLL) and allowing userspace to
control the final power down which is useful for tuning retention of
DSP firmware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown