OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
A subsequent patch adds code on OMAP2xxx to dynamically allocate the
CPUFreq frequency table in clk_init_cpufreq_table(), so for it to
avoid a leak, it will need a corresponding function to free the
memory. This patch adds clk_exit_cpufreq_table() with generic
code to call a chip-specific variant inside the clockfw_lock spinlock via
struct clk_functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 10db25fea4 causes the following
kernel messages during N800 boot (and presumably all other 2420
boards):
[ 0.000000] BUG: mapping for 0x58000000 at 0xe0000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x59000000 at 0xe1000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x5a000000 at 0xe2000000 overlaps vmalloc space
Fix by remapping the IVA memory areas somewhere outside vmalloc space.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Out of the three major OMAP2 chip types, OMAP2420, OMAP2430, and OMAP3430,
we only map the IVA on OMAP2420. The memory mapping is not shared between
OMAP2420 and OMAP2430, so it is inappropriate to label those macros as
'24XX'; this patch changes them to '2420'.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 9905a43b made struct backlight_ops const. Omap was
setting check_fb dynamically, which caused the following
compile error:
drivers/video/backlight/omap1_bl.c: In function 'omapbl_probe':
drivers/video/backlight/omap1_bl.c:142: error: assignment of read-only variable 'omapbl_ops'
Turns out pdata->check_fb is not being used, so just remove
it to fix the compile.
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 35c9049b27 added
drivers/spi/omap_spi_100k.c.
This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In original implementation, the revision passed to
these macros contained revision number in lower nibble.
But, later the revision bits (OMAP_REVBITS_XX) were
defined to use omap_revision[15:08] where revision
number is containied in higher nibble.
This patch updates the macros; else incorrect revision
is detected for OMAP35xx devices.
Signed-off-by: Sanjeev Premi <premi@ti.com>
The runtime detection of OMAP3515 and OMAP3525
was reversed.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove unused data type omap_gpio_switch_config
Thereby also get rid of following sparse warnings:
arch/arm/plat-omap/include/plat/board.h :121:20:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :122:19:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :123:24:
warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For NAND devices '2' should be used with GPMC_CONFIG1_DEVICETYPE
instead of '1'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.
Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch fixes the PRM and CM base addresses and adds
a new CM2 base address for OMAP4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rather than having to do a usecs = nsecs / NSECS_PER_USEC to
track latency in usecs, just track it in nanoseconds.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Following the model of to_platform_device(), add to_omap_device()
macro so a platform_device pointer can be converted into an
omap_device pointer.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Replace the existing u8 array of module MPU IRQ lines with a struct
that includes a name - similar to the existing struct
omap_hwmod_dma_info. Device drivers can then use
platform_get_resource_byname() to retrieve specific IRQs without nasty
dependencies on array ordering.
Thanks to Benoît Cousson <b-cousson@ti.com> and Kevin Hilman
<khilman@deeprootsystems.com> for feedback on this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
This patch fills in the OCP_SYSCONFIG.AUTOIDLE handling in the OMAP
hwmod code.
After this patch, the hwmod code will set the module AUTOIDLE bit
(generally <module>.OCP_SYSCONFIG.AUTOIDLE) to 1 by default upon
enable. If the hwmod flag HWMOD_NO_OCP_AUTOIDLE is set, AUTOIDLE will
be set to 0 upon enable. Upon module disable, AUTOIDLE will be set to
1.
Enabling module autoidle should save some power. The only reason to
not set the OCP_SYSCONFIG.AUTOIDLE bit is if there is a bug in the
module RTL, e.g., the MPUINTC block on OMAP3.
Comments from Kevin Hilman <khilman@deeprootsystems.com> inspired this patch,
and Kevin tested an earlier version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix loop bailout off-by-one bugs reported by Juha Leppänen
<juha_motorsportcom@luukku.com>.
This second version incorporates comments from Russell King
<linux@arm.linux.org.uk>. A new macro, 'omap_test_timeout', has
been created, with cleaner code, and existing code has been converted
to use it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Juha Leppänen <juha_motorsportcom@luukku.com>
Cc: Russell King <linux@arm.linux.org.uk>
MPU power domain bank 0 bits are displayed in position of bank 1
in PWRSTS and PREPWRSTS registers. So read them from correct
position
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch rearranges the order of structure members in struct powerdomain
to avoid wasting memory due to alignment restrictions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP1 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the mpu_rate data structures out into their own
files, opp.h and opp_data.c. In the long run, these mpu_rate tables
should be replaced with OPP code.
Also includes a patch from Felipe Balbi <felipe.balbi@nokia.com> to
mark omap1_clk_functions as __initdata to avoid a section warning:
http://patchwork.kernel.org/patch/64366/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Nishanth Menon <nm@ti.com>
The OMAP2 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the prcm_config data structures out into their own
files, opp2xxx.h and opp24{2,3}0_data.c, and only build in the OPP tables
for the target device. This should save some memory. In the long run,
these prcm_config tables should be replaced with OPP code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
The OMAP3 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
The core files of DSS2. DSS2 commits are split a bit artificially to
make the individual commits smaller, and DSS2 doesn't compile properly
without the rest of the core commits. This shouldn't be a problem, as no
configuration uses DSS2 yet.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
VRFB rotation engine is a block in OMAP2/3 that offers 12 independent
contexts that can be used for framebuffer rotation.
Each context has a backend area of real memory, where it stores the
pixels in undisclosed format. This memory is offered to users via 4
virtual memory areas, which see the same memory area in different
rotation angles (0, 90, 180 and 270 degrees).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add a Video RAM manager for OMAP 2 and 3 platforms. VRAM manager is used
to allocate large continuous blocks of SDRAM or SRAM. The features VRAM
manager has that are missing from dma_alloc_* functions are:
- Support for OMAP2's SRAM
- Allocate without ioremapping
- Allocate at defined physical addresses
- Allows larger VRAM area and larger allocations
The upcoming DSS2 uses VRAM manager.
VRAM area size can be defined in kernel config, board file or with
kernel boot parameters. Board file definition overrides kernel config,
and boot parameter overrides kernel config and board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Split arch/arm/plat-omap/include/mach/omapfb.h into two files:
include/linux/omapfb.h - ioctls etc for userspace and some kernel
stuff for board files
drivers/video/omap/omapfb.h - for omapfb internal use
This cleans up omapfb.h and also makes it easier for the upcoming new
DSS driver to co-exist with the old driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
SMS_ROT_* registers are used by VRFB rotation engine.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Added runtime programming for the differences in EHCI interface between
OMAP3EVM revisions (Rev >= E) and (Rev < E).
Changes:
- EHCI PHY reset GPIO pin is 21 on Rev >= E while Rev < E
uses GPIO pin 135.
- Rev >= E uses EHCI Vbus enable GPIO22 line.
- Rev >= E uses GPIO61 to select EHCI port either on main board or
on Mistral Daughter Card (MDC). OMAP3EVM Rev < E doesn't have
EHCI port on main board.
- Currently GPIO61 it programmed to enable EHCI port on main
board only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Added function to differentiate between the OMAP3EVM revisions. The
chip-id of the ethernet PHY is being used for this purpose.
Rev A to D : 0x01150000
Rev >= E : 0x92200000
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch uses a tasklet implementation for
sending mailbox messages.
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Ramesh Gupta G <grgupta@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Also removed from tx_data
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds resource information of mailbox driver for
OMAP4 mailbox module. Register base address also added
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Ramesh Gupta G <grgupta@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tero Kristo