Commit 35c9049b27 added
drivers/spi/omap_spi_100k.c.
This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added runtime programming for the differences in EHCI interface between
OMAP3EVM revisions (Rev >= E) and (Rev < E).
Changes:
- EHCI PHY reset GPIO pin is 21 on Rev >= E while Rev < E
uses GPIO pin 135.
- Rev >= E uses EHCI Vbus enable GPIO22 line.
- Rev >= E uses GPIO61 to select EHCI port either on main board or
on Mistral Daughter Card (MDC). OMAP3EVM Rev < E doesn't have
EHCI port on main board.
- Currently GPIO61 it programmed to enable EHCI port on main
board only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
The MMC mux pins normally used by omap chips in devices.c
are different from what is needed by omap7xx chips. This
change adds a conditional around the mux setup code to
enable the correct mux pins.
The omap730 and omap850 both use a different clock for the "fck"
clock of the MMC interface than other omap processors based on the
SOFT_REQ_REG, pin 12. The "ick" clock is the same as that used
by other omap processors.
* Added the missing clock definition as mmc3_ck to clock.h
* Added the clock definition to omap_clks in clock.c
* Added CK_7XX to the mmci-omap.0 "ick" clock already in clock.c
With these changes, it is now possible to initialize and use MMC
cards with omap730 and omap850 devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cory Maccarrone