Earlier all poll routine can process rx and tx, But now
one poll routine to process rx + tx and other for rx only.
Last msix vector will be used for separate tx interrupt.
o This is supported from fw version 4.4.2.
o Bump version 5.0.5
Signed-off-by: Sony Chacko <schacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove extra printing of mac address
o This driver also supports NIC only Qlogic adapters.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device soft reset, don't halt every device block.
Access to some blocks is required during recovery.
Signed-off-by: Sucheta Chakraborty <sucheta@dut4145.unminc.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes dma_get_ops() prefetch optimization in bnx2.
bnx2 uses dma_get_ops() to see if dma_sync_single_for_cpu() is
noop. bnx2 does prefetch if it's noop.
But dma_get_ops() isn't available on all the architectures (only the
architectures that uses dma_map_ops struct have it). Using
dma_get_ops() in drivers leads to compilation breakage on many
architectures.
This patch removes dma_get_ops() and changes bnx2 to do prefetch on
all the architectures. This adds useless prefetch on non-coherent
architectures but this is harmless. It is also unlikely to cause the
performance drop.
[ Remove now unused local variable 'pdev' -DaveM ]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements a proper modification of RX skb buffers before
recycling. Adjusting only skb->data is not enough because after that
skb->tail and skb->len become incorrect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs:
serial_cs:
add new id (TOSHIBA Modem/LAN Card)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing the following command on host:
$ ifconfig eth2 mtu 1600 ; ping 10.0.0.27 -s 1485 -c 1
Makes some boards (tested with MPC8315 rev 1.1 and MPC8313 rev 1.0)
oops like this:
skb_over_panic: text:c0195914 len:1537 put:1537 head:c79e4800 data:c79e4880 tail:0xc79e4e81 end:0xc79e4e80 dev:eth1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:127!
Oops: Exception in kernel mode, sig: 5 [#1]
MPC831x RDB
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
NIP: c01c1840 LR: c01c1840 CTR: c016d918
[...]
NIP [c01c1840] skb_over_panic+0x48/0x5c
LR [c01c1840] skb_over_panic+0x48/0x5c
Call Trace:
[c0339d50] [c01c1840] skb_over_panic+0x48/0x5c (unreliable)
[c0339d60] [c01c3020] skb_put+0x5c/0x60
[c0339d70] [c0195914] gfar_clean_rx_ring+0x25c/0x3d0
[c0339dc0] [c01976e8] gfar_poll+0x170/0x1bc
Dumped buffer descriptors showed that eTSEC's length/truncation
logic sometimes passes oversized packets, i.e. for the above ICMP
packet the following two buffer descriptors may become ready:
status=1400 length=1536
status=1800 length=1541
So, it seems that gianfar actually receives the whole big frame,
and it tries to place the packet into two BDs. This situation
confuses the driver, and so the skb_put() sanity check fails.
This patch fixes the issue by adding an appropriate check, i.e.
the driver should not try to process frames with buffer
descriptor's length over rx_buffer_size (i.e. maxfrm and mrblr).
Note that sometimes eTSEC works correctly, i.e. in the second
(last) buffer descriptor bits 'truncated' and 'crcerr' are set,
and so there's no oops. Though I couldn't find any logic when
it works correctly and when not.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds UFO to the list of GSO features with a software
fallback. This allows UFO to be used even if the hardware does
not support it.
In particular, this allows us to test the UFO fallback, as it
has been reported to not work in some cases.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port reset operations and memory add/remove operations need to
be serialized to avoid a kernel deadlock. The deadlock is caused
by calling the napi_disable() function twice.
Therefore we have to employ the dlpar_mem_lock in the ehea_reset_port
function as well
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the eHEA poll function an rmb() is required. Without that some packets
on the receive queue are not seen and thus delayed until the next interrupt
is handled for the same receive queue.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the restriction that only allows connecting to a unix domain
socket identified by unix path that is in the same network namespace.
Crossing network namespaces is always tricky and we did not support
this at first, because of a strict policy of don't mix the namespaces.
Later after Pavel proposed this we did not support this because no one
had performed the audit to make certain using unix domain sockets
across namespaces is safe.
What fundamentally makes connecting to af_unix sockets in other
namespaces is safe is that you have to have the proper permissions on
the unix domain socket inode that lives in the filesystem. If you
want strict isolation you just don't create inodes where unfriendlys
can get at them, or with permissions that allow unfriendlys to open
them. All nicely handled for us by the mount namespace and other
standard file system facilities.
I looked through unix domain sockets and they are a very controlled
environment so none of the work that goes on in dev_forward_skb to
make crossing namespaces safe appears needed, we are not loosing
controll of the skb and so do not need to set up the skb to look like
it is comming in fresh from the outside world. Further the fields in
struct unix_skb_parms should not have any problems crossing network
namespaces.
Now that we handle SCM_CREDENTIALS in a way that gives useable values
across namespaces. There does not appear to be any operational
problems with encouraging the use of unix domain sockets across
containers either.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In unix_skb_parms store pointers to struct pid and struct cred instead
of raw uid, gid, and pid values, then translate the credentials on
reception into values that are meaningful in the receiving processes
namespaces.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start capturing not only the userspace pid, uid and gid values of the
sending process but also the struct pid and struct cred of the sending
process as well.
This is in preparation for properly supporting SCM_CREDENTIALS for
sockets that have different uid and/or pid namespaces at the different
ends.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Serge E. Hallyn <serge@hallyn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
scm_send occasionally allocates state in the scm_cookie, so I have
modified netlink_sendmsg to guarantee that when scm_send succeeds
scm_destory will be called to free that state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct pid and struct cred to store the peer credentials on struct
sock. This gives enough information to convert the peer credential
information to a value relative to whatever namespace the socket is in
at the time.
This removes nasty surprises when using SO_PEERCRED on socket
connetions where the processes on either side are in different pid and
user namespaces.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep the coming code clear and to allow both the sock
code and the scm code to share the logic introduce a
fuction to translate from struct cred to struct ucred.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define what happens when a we view a uid from one user_namespace
in another user_namepece.
- If the user namespaces are the same no mapping is necessary.
- For most cases of difference use overflowuid and overflowgid,
the uid and gid currently used for 16bit apis when we have a 32bit uid
that does fit in 16bits. Effectively the situation is the same,
we want to return a uid or gid that is not assigned to any user.
- For the case when we happen to be mapping the uid or gid of the
creator of the target user namespace use uid 0 and gid as confusing
that user with root is not a problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder the fields in scm_cookie so they pack better on 64bit.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These comments were forgotten in the initial patch to add this
functionality. This patch corrects that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
https://bugzilla.kernel.org/show_bug.cgi?id=16183
The sch_teql module, which can be used to load balance over a set of
underlying interfaces, stopped working after 2.6.30 and has been
broken in all kernels since then for any underlying interface which
requires the addition of link level headers.
The problem is that the transmit routine relies on being able to
access the destination address in the skb in order to do address
resolution once it has decided which underlying interface it is going
to transmit through.
In 2.6.31 the IFF_XMIT_DST_RELEASE flag was introduced, and set by
default for all interfaces, which causes the destination address to be
released before the transmit routine for the interface is called.
The solution is to clear that flag for teql interfaces.
Signed-off-by: Tom Hughes <tom@compton.nu>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed the driver version number to 5.0.4
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was not detecting the presence of NIC partitioning capability of the
firmware properly. Now, it checks the eswitch set bit in the FW capabilities
register and accordingly sets the driver mode as NPAR capable or not.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discard the ACK if we find options that do not match current sysctl
settings.
Previously it was possible to create a connection with sack, wscale,
etc. enabled even if the feature was disabled via sysctl.
Also remove an unneeded call to tcp_sack_reset() in
cookie_check_timestamp: Both call sites (cookie_v4_check,
cookie_v6_check) zero "struct tcp_options_received", hand it to
tcp_parse_options() (which does not change tcp_opt->num_sacks/dsack)
and then call cookie_check_timestamp().
Even if num_sacks/dsacks were changed, the structure is allocated on
the stack and after cookie_check_timestamp returns only a few selected
members are copied to the inet_request_sock.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the RCTRL_TS_ENABLE bit was set unconditionally. However, if
the RCTRL_TS_ENABLE is set without TMR_CTRL[TE], the driver does not work
properly on some boards (Anton had problems with the MPC8313ERDB and
MPC8568EMDS).
With this patch the bit will only be set if requested from user space
with the SIOCSHWTSTAMP ioctl command, meaning that time stamping is
disabled during normal operation. Users who are not interested in time
stamps will not experience problems with buggy CPU revisions or
performance drops any more.
The setting of TMR_CTRL[TE] is still up to the user. This is considered
safe because users wanting HW timestamps must initialize the eTSEC clock
first anyway, e.g. with the recently submitted PTP clock driver.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
regression introduced by b8d92c9c14
In function ‘ieee80211_work_rx_queued_mgmt’:
warning: ‘rma’ may be used uninitialized in this function
this re-adds default value WORK_ACT_NONE back to rma
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only report PHY error frames for ANI on chipsets which do not have PHY error
counters in hardware.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed RX descriptor functions against the HAL sources. Some minor changes:
- check size before making changes to the descriptor
- whitespace
- add comments about 5210 timestamps. this needs to be adressed later!
- FIFO overrun error only available on 5210
- rs_phyerr should not be OR'ed
- clear the whole ath5k_rx_status structure before using, instead of
zeroing specific fields.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some differences between 5210 and 5211 descriptors which we did not
take into account before.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update 5210 frame types to match the HAL. We have to apply the same bitshift to
the constants as we use later.
Add 5211 specific frame types.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I carefully reviewed desh.h against the HAL sources. Added comments and made
differences between 5210, 5211 and 5212 more clear by adding _521x to the
defines which are specific to that chipset. Renamed some defines. No functional
changes.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_hw_rx_error was only used once, where we could easily just use
ath5k_hw_rx_status as well, so remove it.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just whitespace and indentation.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use direct function calls for ath5k_hw_setup_rx_desc() and
ath5k_hw_setup_mrr_tx_desc() instead of a function pointer which always pointed
to the same function in the case of ath5k_hw_setup_rx_desc() and which is
easily unified in the case of ath5k_hw_setup_mrr_tx_desc().
Also simplify the initialization function for the remaining function pointers.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create a new function ath5k_receive_frame_ok() which checks for errors, updates
error statistics and tells us if we want to further "receive" this frame or
not. This way we can avoid a goto and have a cleaner separation between buffer
handling and other things.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move frame reception into it's own function to have a clearer separation
between buffer and descriptor handling and things that are done when we
actually receive a frame.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason for a special handling (return) here, just break like we do
with the checks before.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After we free skbs for receive or transmit descriptors, make sure we have no
pointers to the now invalid memory address.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the debug ouptut rx_status_0 was printed twice instead of rx_status_1. Also
make the debug message more clear.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix comment about dma sizes, brackets were missing. Replace 'insure' with
'ensure'.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename ath5k_txbuf_free() to ath5k_txbuf_free_skb() since this is what it does:
it frees the skb and not the buf. Same for ath5k_rxbuf_free().
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: http://bugs.launchpad.net/bugs/21367
Enable LED by default and update the MODULE_PARM_DESC. The original
reason for defaulting to disabled was documented in 2005 and noted, "The
LED code has been reported to hang some systems when running ifconfig
and is therefore disabled by default." This no longer appears
applicable and users have been requesting this be enabled for several
years.
Signed-off-by: TJ <ubuntu@tjworld.net>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Medion MD40900 device id [0x0cde, 0x0006] is defined twice.
Comment out the duplicate.
Originally-by: Ben Collins <ben.collins@ubuntu.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Addition of rcu_head to struct inet_peer added 16bytes on 64bit arches.
Thats a bit unfortunate, since old size was exactly 64 bytes.
This can be solved, using an union between this rcu_head an four fields,
that are normally used only when a refcount is taken on inet_peer.
rcu_head is used only when refcnt=-1, right before structure freeing.
Add a inet_peer_refcheck() function to check this assertion for a while.
We can bring back SLAB_HWCACHE_ALIGN qualifier in kmem cache creation.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
0x49 is used by PLANEX GW-US54GXS (2019:5303).
Signed-off-by: Kouhei Sutou <kou@clear-code.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
schacko