Driver anchors the tx urbs and defers the urb submission if
a transmit request comes when the interface is suspended.
Anchoring urb increments the urb reference count. These
deferred urbs are later accessed by calling usb_get_from_anchor()
for submission during interface resume. usb_get_from_anchor()
unanchors the urb but urb reference count remains same.
This causes the urb reference count to remain non-zero
after usb_free_urb() gets called and urb never gets freed.
Hence call usb_put_urb() after anchoring the urb to properly
balance the reference count for these deferred urbs. Also,
unanchor these deferred urbs during disconnect, to free them
up.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a failure takes place during the EQ creation, we need to unmap the
UAR memory block too.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Uri Habusha <urih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan tag can be zero. This is why it can't serve as an indication
that packet requires VLAN header in the TX flow.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QP range is reserved as a single block. However, when freeing the
en resources, the tx-ring QPs are released both in mlx4_en_destroy_tx_ring
(one at a time) and in mlx4_en_free_resources (as a block release).
Fix by eliminating the one-at-a-time release in mlx4_en_destroy_tx_ring.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The delayed work function int_in_work() may call usb_reset_device()
and thus, indirectly, the driver's pre_reset method. Trying to
cancel the work synchronously in that situation would deadlock.
Fix by avoiding cancel_work_sync() in the pre_reset method.
If the reset was NOT initiated by int_in_work() this might cause
int_in_work() to run after the post_reset method, with urb_int_in
already resubmitted, so handle that case gracefully.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 871ae57adc, which is
scheduled for v3.8 and accidently got into v3.7-rc series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
In order to decide if ktest should bother installing modules on the
target box, it checks if the config file has CONFIG_MODULES=y. But it
also checks if the '=y' part exists. It only will install modules if the
config exists and is set with '=y'. But as the regex that was used
tests:
/^CONFIG_MODULES(=y)?/
this will also match:
CONFIG_MODULES_USE_ELF_RELA
as the '=y' part was optional and it did not test the rest of the line.
When this happens, ktest will stop checking the rest of the configs but
it will also think that no modules are needed to be installed. What it
should do is only jump out of the loop if it actually found a
CONFIG_MODULES that is set to true.
Otherwise, ktest wont install the necessary modules needed for proper
booting of the test target.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull drm radeon fixes from Dave Airlie:
"Just radeon fixes in this one:
- some new PCI IDs
- ATPX regression fix
- async VM regression fixes
- some module options fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix ATPX regression in acpi rework
drm/radeon: fix ATPX function documentation
drm/radeon: move the retry to gem_object_create
drm/radeon: move size limits to gem_object_create.
drm/radeon: use vzalloc for gart pages
drm/radeon: fix and simplify pot argument checks v3
drm/radeon: fix header size estimation in VM code
drm/radeon: remove set_page check from VM code
drm/radeon: fix si_set_page v2
drm/radeon: fix cayman_vm_set_page v2
drm/radeon: fix PFP sync in vm_flush
drm/radeon: add error output if VM CS fails on cayman
drm/radeon: give each backlight a unique id
drm/radeon: fix sparse warning
drm/radeon: add some new SI PCI ids
- Fix the NFSv2/v3 kernel statd protocol, which broke due to net namespace
related changes.
- Fix a number of races in the SUNRPC TCP disconnect/reconnect code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8Dt4
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.7-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS bugfixes from Trond Myklebust:
- Fix the NFSv2/v3 kernel statd protocol, which broke due to net
namespace related changes.
- Fix a number of races in the SUNRPC TCP disconnect/reconnect code.
* tag 'nfs-for-3.7-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
LOCKD: Clear ln->nsm_clnt only when ln->nsm_users is zero
LOCKD: fix races in nsm_client_get
SUNRPC: Get rid of the xs_error_report socket callback
SUNRPC: Prevent races in xs_abort_connection()
Revert "SUNRPC: Ensure we close the socket on EPIPE errors too..."
SUNRPC: Clear the connect flag when socket state is TCP_CLOSE_WAIT
Alex writes:
"Fixes pull request for radeon. The main things here are
fixing a ATPX regression from the acpi rework, fixing some
fallout from the async VM work, and fixing some module options
that were broken in certain cases. Other than that, mainly
just bug fixes."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix ATPX regression in acpi rework
drm/radeon: fix ATPX function documentation
drm/radeon: move the retry to gem_object_create
drm/radeon: move size limits to gem_object_create.
drm/radeon: use vzalloc for gart pages
drm/radeon: fix and simplify pot argument checks v3
drm/radeon: fix header size estimation in VM code
drm/radeon: remove set_page check from VM code
drm/radeon: fix si_set_page v2
drm/radeon: fix cayman_vm_set_page v2
drm/radeon: fix PFP sync in vm_flush
drm/radeon: add error output if VM CS fails on cayman
drm/radeon: give each backlight a unique id
drm/radeon: fix sparse warning
drm/radeon: add some new SI PCI ids
Merge misc fixes from Andrew Morton:
"18 total. 15 fixes and some updates to a device_cgroup patchset which
bring it up to date with the version which I should have merged in the
first place."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (18 patches)
fs/compat_ioctl.c: VIDEO_SET_SPU_PALETTE missing error check
gen_init_cpio: avoid stack overflow when expanding
drivers/rtc/rtc-imxdi.c: add missing spin lock initialization
mm, numa: avoid setting zone_reclaim_mode unless a node is sufficiently distant
pidns: limit the nesting depth of pid namespaces
drivers/dma/dw_dmac: make driver's endianness configurable
mm/mmu_notifier: allocate mmu_notifier in advance
tools/testing/selftests/epoll/test_epoll.c: fix build
UAPI: fix tools/vm/page-types.c
mm/page_alloc.c:alloc_contig_range(): return early for err path
rbtree: include linux/compiler.h for definition of __always_inline
genalloc: stop crashing the system when destroying a pool
backlight: ili9320: add missing SPI dependency
device_cgroup: add proper checking when changing default behavior
device_cgroup: stop using simple_strtoul()
device_cgroup: rename deny_all to behavior
cgroup: fix invalid rcu dereference
mm: fix XFS oops due to dirty pages without buffers on s390
We handle NOTIFY_THROTTLING so don't then fall through to unsupported event.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Decode multitouch reports from the touch sensor of the Cintiq 24HD
touch.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like our other pen-and-touch products, the Cintiq 24HD touch needs data
to be shared between its two sensors to facilitate proximity-based palm
rejection.
Unlike other tablets that report sensor data through separate interfaces
of the same USB device, the Cintiq 24HD touch has separate USB devices
that are connected to an internal USB hub.
This patch makes it possible to designate the USB VID/PID of the other
device so that the two may share data. To ensure we don't accidentally
link to a sensor from a physically separate device (if several have been
plugged in), we limit the search to siblings (i.e., devices directly
connected to the same hub).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If one includes documentation for an external tool, it should be
correct. This is not:
1. Overriding the input to rngd should typically be neither
necessary nor desired. This is especially so since newer
versions of rngd support a number of different *types* of sources.
2. The default kernel-exported device is called /dev/hwrng not
/dev/hwrandom nor /dev/hw_random (both of which were used in the
past; however, kernel and udev seem to have converged on
/dev/hwrng.)
Overall it is better if the documentation for rngd is kept with rngd
rather than in a kernel Makefile.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM fixes from Russell King:
"A random collection of various fixes, mainly from Arnd and a few other
people. Not thing really stands out here."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: drop experimental status for hotplug and Thumb2
ARM: 7560/1: SMP_TWD: use DIV_ROUND_CLOSEST() for periodic mode
ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count
ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD
ARM: 7555/1: kexec: fix segment memory addresses check
ARM: warnings in arch/arm/include/asm/uaccess.h
ARM: binfmt_flat: unused variable 'persistent'
ARM: be really quiet when building with 'make -s'
ARM: pass -marm to gcc by default for both C and assembler
ARM: Xen: fix initial build problems
ARM: export default read_current_timer
ARM: Fix another build warning in arch/arm/mm/alignment.c
ARM: export set_irq_flags
ARM: kprobes: make more tests conditional
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"This consists mainly of a set of one-liner fixes and cleanups for a
few minor issues identified in both Contiguous Memory Allocator code
and ARM DMA-mapping subsystem."
* 'fixes_for_linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: mm: Remove unused arm_vmregion priv field
ARM: dma-mapping: fix build warning in __dma_alloc()
ARM: dma-mapping: support debug_dma_mapping_error
mm: cma: alloc_contig_range: return early for err path
drivers: cma: Fix wrong CMA selected region size default value
drivers: dma-coherent: Fix typo in dma_mmap_from_coherent documentation
drivers: dma-contiguous: Don't redefine SZ_1M
Commit
844ab6f9 x86, mm: Find_early_table_space based on ranges that are actually being mapped
added back some lines back wrongly that has been removed in commit
7b16bbf97 Revert "x86/mm: Fix the size calculation of mapping tables"
remove them again.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQW_vuaYQbmagVnxT2DGsYc=9tNeAbdBq53sYkitPOwxSQ@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The compat ioctl for VIDEO_SET_SPU_PALETTE was missing an error check
while converting ioctl arguments. This could lead to leaking kernel
stack contents into userspace.
Patch extracted from existing fix in grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: David Miller <davem@davemloft.net>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: PaX Team <pageexec@freemail.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix possible overflow of the buffer used for expanding environment
variables when building file list.
In the extremely unlikely case of an attacker having control over the
environment variables visible to gen_init_cpio, control over the
contents of the file gen_init_cpio parses, and gen_init_cpio was built
without compiler hardening, the attacker can gain arbitrary execution
control via a stack buffer overflow.
$ cat usr/crash.list
file foo ${BIG}${BIG}${BIG}${BIG}${BIG}${BIG} 0755 0 0
$ BIG=$(perl -e 'print "A" x 4096;') ./usr/gen_init_cpio usr/crash.list
*** buffer overflow detected ***: ./usr/gen_init_cpio terminated
This also replaces the space-indenting with tabs.
Patch based on existing fix extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: PaX Team <pageexec@freemail.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 957f822a0a ("mm, numa: reclaim from all nodes within reclaim
distance") caused zone_reclaim_mode to be set for all systems where two
nodes are within RECLAIM_DISTANCE of each other. This is the opposite
of what we actually want: zone_reclaim_mode should be set if two nodes
are sufficiently distant.
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Julian Wollrath <jwollrath@web.de>
Tested-by: Julian Wollrath <jwollrath@web.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Patrik Kullman <patrik.kullman@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'struct pid' is a "variable sized struct" - a header with an array of
upids at the end.
The size of the array depends on a level (depth) of pid namespaces. Now a
level of pidns is not limited, so 'struct pid' can be more than one page.
Looks reasonable, that it should be less than a page. MAX_PIS_NS_LEVEL is
not calculated from PAGE_SIZE, because in this case it depends on
architectures, config options and it will be reduced, if someone adds a
new fields in struct pid or struct upid.
I suggest to set MAX_PIS_NS_LEVEL = 32, because it saves ability to expand
"struct pid" and it's more than enough for all known for me use-cases.
When someone finds a reasonable use case, we can add a config option or a
sysctl parameter.
In addition it will reduce the effect of another problem, when we have
many nested namespaces and the oldest one starts dying.
zap_pid_ns_processe will be called for each namespace and find_vpid will
be called for each process in a namespace. find_vpid will be called
minimum max_level^2 / 2 times. The reason of that is that when we found a
bit in pidmap, we can't determine this pidns is top for this process or it
isn't.
vpid is a heavy operation, so a fork bomb, which create many nested
namespace, can make a system inaccessible for a long time. For example my
system becomes inaccessible for a few minutes with 4000 processes.
[akpm@linux-foundation.org: return -EINVAL in response to excessive nesting, not -ENOMEM]
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dw_dmac driver was originally developed for avr32 to be used with the
Synopsys DesignWare AHB DMA controller. Starting from 2.6.38, access to
the device's i/o memory was done with the little-endian readl/writel
functions(1)
This broke the driver for the avr32 platform, because it needs big
(native) endian accessors. This patch makes the endianness configurable
using 'DW_DMAC_BIG_ENDIAN_IO', which will default be true for AVR32
I submitted this patch before(2) but then waited for Andy to finish other
changes to the same module(3).
(1) https://patchwork.kernel.org/patch/608211
(2) https://lkml.org/lkml/2012/8/26/148
(3) https://lkml.org/lkml/2012/9/21/173
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Havard Skinnemoen <havard@skinnemoen.net>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While allocating mmu_notifier with parameter GFP_KERNEL, swap would start
to work in case of tight available memory. Eventually, that would lead to
a deadlock while the swap deamon swaps anonymous pages. It was caused by
commit e0f3c3f78d ("mm/mmu_notifier: init notifier if necessary").
=================================
[ INFO: inconsistent lock state ]
3.7.0-rc1+ #518 Not tainted
---------------------------------
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
kswapd0/35 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&mapping->i_mmap_mutex){+.+.?.}, at: page_referenced+0x9c/0x2e0
{RECLAIM_FS-ON-W} state was registered at:
mark_held_locks+0x86/0x150
lockdep_trace_alloc+0x67/0xc0
kmem_cache_alloc_trace+0x33/0x230
do_mmu_notifier_register+0x87/0x180
mmu_notifier_register+0x13/0x20
kvm_dev_ioctl+0x428/0x510
do_vfs_ioctl+0x98/0x570
sys_ioctl+0x91/0xb0
system_call_fastpath+0x16/0x1b
irq event stamp: 825
hardirqs last enabled at (825): _raw_spin_unlock_irq+0x30/0x60
hardirqs last disabled at (824): _raw_spin_lock_irq+0x19/0x80
softirqs last enabled at (0): copy_process+0x630/0x17c0
softirqs last disabled at (0): (null)
...
Simply back out the above commit, which was a small performance
optimization.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reported-by: Andrea Righi <andrea@betterlinux.com>
Tested-by: Andrea Righi <andrea@betterlinux.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Sagi Grimberg <sagig@mellanox.co.il>
Cc: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Latest Linus head run of "make selftests" in the tools directory failed
with references to undefined variables. Reference was to
'write_thread_data' which is the name of a struct that is being used, not
the variable itself. Change reference so it points to the variable.
Signed-off-by: Daniel Hazelton <dshadowwolf@gmail.com>
Cc: "Paton J. Lewis" <palewis@adobe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix tools/vm/page-types.c to use the UAPI variant of linux/kernel-page-flags.h
lest the following error appear:
In file included from page-types.c:38:0:
../../include/linux/kernel-page-flags.h:4:42: fatal error:
uapi/linux/kernel-page-flags.h: No such file or directory
Reported-by: Daniel Hazelton <dshadowwolf@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Daniel Hazelton <dshadowwolf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If start_isolate_page_range() failed, unset_migratetype_isolate() has been
done inside it.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Cc: Ni zhan Chen <nizhan.chen@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rb_erase_augmented() is a static function annotated with
__always_inline. This causes a compile failure when attempting to use
the rbtree implementation as a library (e.g. kvm tool):
rbtree_augmented.h:125:24: error: expected `=', `,', `;', `asm' or `__attribute__' before `void'
Include linux/compiler.h in rbtree_augmented.h so that the __always_inline
macro is resolved correctly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The genalloc code uses the bitmap API from include/linux/bitmap.h and
lib/bitmap.c, which is based on long values. Both bitmap_set from
lib/bitmap.c and bitmap_set_ll, which is the lockless version from
genalloc.c, use BITMAP_LAST_WORD_MASK to set the first bits in a long in
the bitmap.
That one uses (1 << bits) - 1, 0b111, if you are setting the first three
bits. This means that the API counts from the least significant bits
(LSB from now on) to the MSB. The LSB in the first long is bit 0, then.
The same works for the lookup functions.
The genalloc code uses longs for the bitmap, as it should. In
include/linux/genalloc.h, struct gen_pool_chunk has unsigned long
bits[0] as its last member. When allocating the struct, genalloc should
reserve enough space for the bitmap. This should be a proper number of
longs that can fit the amount of bits in the bitmap.
However, genalloc allocates an integer number of bytes that fit the
amount of bits, but may not be an integer amount of longs. 9 bytes, for
example, could be allocated for 70 bits.
This is a problem in itself if the Least Significat Bit in a long is in
the byte with the largest address, which happens in Big Endian machines.
This means genalloc is not allocating the byte in which it will try to
set or check for a bit.
This may end up in memory corruption, where genalloc will try to set the
bits it has not allocated. In fact, genalloc may not set these bits
because it may find them already set, because they were not zeroed since
they were not allocated. And that's what causes a BUG when
gen_pool_destroy is called and check for any set bits.
What really happens is that genalloc uses kmalloc_node with __GFP_ZERO
on gen_pool_add_virt. With SLAB and SLUB, this means the whole slab
will be cleared, not only the requested bytes. Since struct
gen_pool_chunk has a size that is a multiple of 8, and slab sizes are
multiples of 8, we get lucky and allocate and clear the right amount of
bytes.
Hower, this is not the case with SLOB or with older code that did memset
after allocating instead of using __GFP_ZERO.
So, a simple module as this (running 3.6.0), will cause a crash when
rmmod'ed.
[root@phantom-lp2 foo]# cat foo.c
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/genalloc.h>
MODULE_LICENSE("GPL");
MODULE_VERSION("0.1");
static struct gen_pool *foo_pool;
static __init int foo_init(void)
{
int ret;
foo_pool = gen_pool_create(10, -1);
if (!foo_pool)
return -ENOMEM;
ret = gen_pool_add(foo_pool, 0xa0000000, 32 << 10, -1);
if (ret) {
gen_pool_destroy(foo_pool);
return ret;
}
return 0;
}
static __exit void foo_exit(void)
{
gen_pool_destroy(foo_pool);
}
module_init(foo_init);
module_exit(foo_exit);
[root@phantom-lp2 foo]# zcat /proc/config.gz | grep SLOB
CONFIG_SLOB=y
[root@phantom-lp2 foo]# insmod ./foo.ko
[root@phantom-lp2 foo]# rmmod foo
------------[ cut here ]------------
kernel BUG at lib/genalloc.c:243!
cpu 0x4: Vector: 700 (Program Check) at [c0000000bb0e7960]
pc: c0000000003cb50c: .gen_pool_destroy+0xac/0x110
lr: c0000000003cb4fc: .gen_pool_destroy+0x9c/0x110
sp: c0000000bb0e7be0
msr: 8000000000029032
current = 0xc0000000bb0e0000
paca = 0xc000000006d30e00 softe: 0 irq_happened: 0x01
pid = 13044, comm = rmmod
kernel BUG at lib/genalloc.c:243!
[c0000000bb0e7ca0] d000000004b00020 .foo_exit+0x20/0x38 [foo]
[c0000000bb0e7d20] c0000000000dff98 .SyS_delete_module+0x1a8/0x290
[c0000000bb0e7e30] c0000000000097d4 syscall_exit+0x0/0x94
--- Exception: c00 (System Call) at 000000800753d1a0
SP (fffd0b0e640) is in userspace
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Benjamin Gaignard <benjamin.gaignard@stericsson.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add this missing SPI dependency and prevent the driver from building
without SPI, because functions of the spi driver are used in this
driver.
drivers/video/backlight/ili9320.c:51: undefined reference to `spi_sync'
Also, a prompt string for CONFIG_LCD_ILI9320 is added for explicit
selection.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before changing a group's default behavior to ALLOW, we must check if
its parent's behavior is also ALLOW.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the code to use kstrtou32() instead of simple_strtoul() which is
deprecated. The real size of the variables are u32, so use kstrtou32
instead of kstrtoul
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was done in a v2 patch but v1 ended up being committed. The
variable name is less confusing and stores the default behavior when no
matching exception exists.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On s390 any write to a page (even from kernel itself) sets architecture
specific page dirty bit. Thus when a page is written to via buffered
write, HW dirty bit gets set and when we later map and unmap the page,
page_remove_rmap() finds the dirty bit and calls set_page_dirty().
Dirtying of a page which shouldn't be dirty can cause all sorts of
problems to filesystems. The bug we observed in practice is that
buffers from the page get freed, so when the page gets later marked as
dirty and writeback writes it, XFS crashes due to an assertion
BUG_ON(!PagePrivate(page)) in page_buffers() called from
xfs_count_page_state().
Similar problem can also happen when zero_user_segment() call from
xfs_vm_writepage() (or block_write_full_page() for that matter) set the
hardware dirty bit during writeback, later buffers get freed, and then
page unmapped.
Fix the issue by ignoring s390 HW dirty bit for page cache pages of
mappings with mapping_cap_account_dirty(). This is safe because for
such mappings when a page gets marked as writeable in PTE it is also
marked dirty in do_wp_page() or do_page_fault(). When the dirty bit is
cleared by clear_page_dirty_for_io(), the page gets writeprotected in
page_mkclean(). So pagecache page is writeable if and only if it is
dirty.
Thanks to Hugh Dickins for pointing out mapping has to have
mapping_cap_account_dirty() for things to work and proposing a cleaned
up variant of the patch.
The patch has survived about two hours of running fsx-linux on tmpfs
while heavily swapping and several days of running on out build machines
where the original problem was triggered.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@vger.kernel.org> [3.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hi Greg,
Here's four trivial xHCI bug fixes for 3.7. They clean up some issues found
while running Coverity across the xHCI driver. One is marked for stable.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQiZ5JAAoJEBMGWMLi1Gc5UsQQAKcZfrAHPGwT768YthCJNOCM
W0ec/n5mVdp6sbXVkDltC2mfJoPrykZlr/hL9Rie9q/i1QFLEW8ig0/LQrPSq9OO
4aE4+n1tDCi4Mdo/ABT6orOhqTo2+5J5dErzFbpzFuZl1vELtZBe+FTKj5D04KlZ
NlUyKuqRlVuVLPIt0Wmsbxt6vaQAAe2tNNWlUC/+TG9QQnZpmJi/BKIztF/uTRlZ
O3Mk0KtW3rLBUU2lxJR6cq7BxH3d2mL2MCDfSZ7tjciJQID8mtb11Q+9yWx2Xy3N
VJ/gCvzAFPAWyFKffeBCE28B/IKtS4hHi/sxBKZvojzP0aFOwUQnTK6Te+VxR+uL
4tF9Z54QP6nONAswSyTPpWvBDHKCBt85P2kD2ynVP95Bh8HzSKofZu25jdQkdBVN
1zZfu2o/xxY+lK6e4BE75mEo33A1y65JqMaZoo/qYxvckRgUOFfK3KVs4WyGmaMN
HHVZThFAZ10b0WDCULt2cHCsQmVbWQANR8hDynppMc0IiYv5fUmuRqzrX+PEJCiD
CzmTXyDvI5IC4XJIpHHUIFQYHf5VL5A9Rt5dEFCR1mkhnNstJTRqHIFfE8X9fAM8
boo9378k1J3N5HBLrZJ1HkT1/lzBTC+RkkaVVP7zki/lGS+aRxdKoZ6RVs9Upfzb
v4SUugrYBxMDrGHeuEGz
=4I1Y
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xHCI trivial fixes for 3.7
Hi Greg,
Here's four trivial xHCI bug fixes for 3.7. They clean up some issues found
while running Coverity across the xHCI driver. One is marked for stable.
Sarah Sharp
Remove the variable ep_ctx from xhci_add_endpoint(), since it is
assigned but unused. Caught by Coverity.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Remove the variable slot_ctx from xhci_dbg_ctx(), since it is assigned
but unused. Caught by Coverity.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Coverity complains that xhci_evaluate_context_result() is missing a
break statement after the COMP_EBADSLT switch case. It's not a big
deal, since we wanted to return the same error code as the case
statement below it does. The end result would be one that a Slot
Disabled error completion code would also print the warning message
associated with a Context State error code. No other bad behavior would
result.
It's not worth backporting to stable kernels, since it only fixes an
issue with too much debugging.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The command cancellation code doesn't check whether find_trb_seg()
couldn't find the segment that contains the TRB to be canceled. This
could cause a NULL pointer deference later in the function when next_trb
is called. It's unlikely to happen unless something is wrong with the
command ring pointers, so add some debugging in case it happens.
This patch should be backported to stable kernels as old as 3.0, that
contain the commit b63f4053cc "xHCI:
handle command after aborting the command ring".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
We BUG if we fail to commit the transaction when creating a snapshot, which
is just obnoxious. Remove the BUG_ON(). Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
After cloning root's node, we forgot to dec the src's ref
which can lead to a memory leak.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
On a really full file system I was getting ENOSPC back from
btrfs_update_inode when trying to update the parent inode when creating a
snapshot. Just use the fallback method so we can update the inode and not
have to worry about having a delayed ref. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
This patch also requires a change in the user-space part of "receive".
We need to use "lchown" instead of "chown". We will do this in the
following patch.
Signed-off-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
if (S_ISREG(sctx->cur_inode_mode)) {
Steps to reproduce:
# mkfs.btrfs -m raid1 <disk1> <disk2>
# btrfstune -S 1 <disk1>
# mount <disk1> <mnt>
# btrfs device add <disk3> <disk4> <mnt>
# mount -o remount,rw <mnt>
# dd if=/dev/zero of=<mnt>/tmpfile bs=1M count=1
Deadlock happened.
It is because of the nested chunk allocation. When we wrote the data
into the filesystem, we would allocate the data chunk because there was
no data chunk in the filesystem. At the end of the data chunk allocation,
we should insert the metadata of the data chunk into the extent tree, but
there was no raid1 chunk, so we tried to lock the chunk allocation mutex to
allocate the new chunk, but we had held the mutex, the deadlock happened.
By rights, we would allocate the raid1 chunk when we added the second device
because the profile of the seed filesystem is raid1 and we had two devices.
But we didn't do that in fact. It is because the last step of the first device
insertion didn't commit the transaction. So when we added the second device,
we didn't cow the tree, and just inserted the relative metadata into the leaves
which were generated by the first device insertion, and its profile was dup.
So, I fix this problem by commiting the transaction at the end of the first
device insertion.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Currently if len argument in btrfs_ioctl_fitrim() is smaller than
one FSB we will continue and finally return 0 bytes discarded.
However if the length to discard is smaller then file system block
we should really return EINVAL.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Hemant Kumar