Allow drivers to optimise out the register cache sync if they didn't need
to do one. If the hardware is desynced from the register cache (by power
loss for example) then the driver should call regcache_mark_dirty() to
let the core know about this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Give regcache_lzo_block_count() a copy of the map so that when we decide
we want to make the LZO cache more controllable we can more easily do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
There seem to be lots of regmap-using devices with very similar interrupt
controllers with a small bank of interrupt registers and mask registers
with an interrupt per bit. This won't cover everything but it's a good
start.
Each chip supplies a base for the status registers, a base for the mask
registers, an optional base for writing acknowledgements (which may be the
same as the status registers) and an array of bits within each of these
register banks which indicate the interrupt.
There is an assumption that the bit for each interrupt will be the same
in each of the register bank.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. Therefore
this patch (as1492) adds a mechanism for retrying failed
autosuspends. If the callback routine updates the last_busy field so
that the next autosuspend expiration time is in the future, the
autosuspend will automatically be rescheduled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
With delta type being int, its value is made zero
for all values of now > 0x80000000.
Hence fixing it.
Signed-off-by: venu byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This file isn't using full modular functionality, and hence
can be "downgraded" to just using export.h
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This file is currently relying on <linux/module.h> sneaking it in
through the implicit include paths from device.h. Once that
is cleaned up, this will happen:
In file included from drivers/base/init.c:12:
drivers/base/base.h:34: error: field ‘bus_notifier’ has incomplete type
make[3]: *** [drivers/base/init.o] Error 1
Fix it up in advance, so the cleanup can continue.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Most of these files were implicitly getting EXPORT_SYMBOL via
device.h which was including module.h, but that path will be broken
soon.
[ with input from Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This file was getting <linux/module.h> via an implicit include
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason. Give it the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
* 'for-linus' of git://opensource.wolfsonmicro.com/regmap: (62 commits)
mfd: Enable rbtree cache for wm831x devices
regmap: Support some block operations on cached devices
regmap: Allow caches for devices with no defaults
regmap: Ensure rbtree syncs registers set to zero properly
regmap: Allow rbtree to cache zero default values
regmap: Warn on raw I/O as well as bulk reads that bypass cache
regmap: Return a sensible error code if we fail to read the cache
regmap: Use bsearch() to search the register defaults
regmap: Fix doc comment
regmap: Optimize the lookup path to use binary search
regmap: Ensure we scream if we enable cache bypass/only at the same time
regmap: Implement regcache_cache_bypass helper function
regmap: Save/restore the bypass state upon syncing
regmap: Lock the sync path, ensure we use the lockless _regmap_write()
regmap: Fix apostrophe usage
regmap: Make _regmap_write() global
regmap: Fix lock used for regcache_cache_only()
regmap: Grab the lock in regcache_cache_only()
regmap: Modify map->cache_bypass directly
regmap: Fix regcache_sync generic implementation
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
mm: memory hotplug: Check if pages are correctly reserved on a per-section basis
Revert "memory hotplug: Correct page reservation checking"
Update email address for stable patch submission
dynamic_debug: fix undefined reference to `__netdev_printk'
dynamic_debug: use a single printk() to emit messages
dynamic_debug: remove num_enabled accounting
dynamic_debug: consolidate repetitive struct _ddebug descriptor definitions
uio: Support physical addresses >32 bits on 32-bit systems
sysfs: add unsigned long cast to prevent compile warning
drivers: base: print rejected matches with DEBUG_DRIVER
memory hotplug: Correct page reservation checking
memory hotplug: Refuse to add unaligned memory regions
remove the messy code file Documentation/zh_CN/SubmitChecklist
ARM: mxc: convert device creation to use platform_device_register_full
new helper to create platform devices with dma mask
docs/driver-model: Update device class docs
docs/driver-model: Document device.groups
kobj_uevent: Ignore if some listeners cannot handle message
dynamic_debug: make netif_dbg() call __netdev_printk()
dynamic_debug: make netdev_dbg() call __netdev_printk()
...
Since kfree() checks it its argument is not NULL, it is not necessary
to duplicate this check in __pm_clk_remove().
[rjw: Added the changelog.]
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* pm-domains:
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
The generic PM domains code in drivers/base/power/domain.c has
to avoid powering off domains that provide power to wakeup devices
during system suspend. Currently, however, this only works for
wakeup devices directly belonging to the given domain and not for
their children (or the children of their children and so on).
Thus, if there's a wakeup device whose parent belongs to a power
domain handled by the generic PM domains code, the domain will be
powered off during system suspend preventing the device from
signaling wakeup.
To address this problem introduce a device flag, power.wakeup_path,
that will be set during system suspend for all wakeup devices,
their parents, the parents of their parents and so on. This way,
all wakeup paths in the device hierarchy will be marked and the
generic PM domains code will only need to avoid powering off
domains containing devices whose power.wakeup_path is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
(Resending as I am not seeing it in -next so maybe it got lost)
mm: memory hotplug: Check if pages are correctly reserved on a per-section basis
It is expected that memory being brought online is PageReserved
similar to what happens when the page allocator is being brought up.
Memory is onlined in "memory blocks" which consist of one or more
sections. Unfortunately, the code that verifies PageReserved is
currently assuming that the memmap backing all these pages is virtually
contiguous which is only the case when CONFIG_SPARSEMEM_VMEMMAP is set.
As a result, memory hot-add is failing on those configurations with
the message;
kernel: section number XXX page number 256 not reserved, was it already online?
This patch updates the PageReserved check to lookup struct page once
per section to guarantee the correct struct page is being checked.
[Check pages within sections properly: rientjes@google.com]
[original patch by: nfont@linux.vnet.ibm.com]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1485) documents a change to the kernel's default wakeup
policy. Devices that forward wakeup requests between buses should be
enabled for wakeup by default.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Record S3 failure time about each reason and the latest two failed
devices' names in S3 progress.
We can check it through 'suspend_stats' entry in debugfs.
The motivation of the patch:
We are enabling power features on Medfield. Comparing with PC/notebook,
a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far
more frequently. If it can't enter suspend-2-ram in time, the power
might be used up soon.
We often find sometimes, a device suspend fails. Then, system retries
s3 over and over again. As display is off, testers and developers
don't know what happens.
Some testers and developers complain they don't know if system
tries suspend-2-ram, and what device fails to suspend. They need
such info for a quick check. The patch adds suspend_stats under
debugfs for users to check suspend to RAM statistics quickly.
If not using this patch, we have other methods to get info about
what device fails. One is to turn on CONFIG_PM_DEBUG, but users
would get too much info and testers need recompile the system.
In addition, dynamic debug is another good tool to dump debug info.
But it still doesn't match our utilization scenario closely.
1) user need write a user space parser to process the syslog output;
2) Our testing scenario is we leave the mobile for at least hours.
Then, check its status. No serial console available during the
testing. One is because console would be suspended, and the other
is serial console connecting with spi or HSU devices would consume
power. These devices are powered off at suspend-2-ram.
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If .runtime_suspend() returns -EAGAIN or -EBUSY, the device should
still be in ACTIVE state, so it is not necessary to send an idle
notification to its parent. If .runtime_suspend() returns other
fatal failure, it doesn't make sense to send idle notification to
its parent.
Skip parent idle notification when failure is returned from
.runtime_suspend() and update comments in rpm_suspend() to reflect
that change.
[rjw: Modified the subject and changelog slightly.]
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch fix kerneldoc comments for rpm_suspend():
- 'Cancel a pending idle notification' should be put before, also
should be changed to 'Cancel a pending idle notification,
autosuspend or suspend'.
- idle notification for the device after succeeding suspend has
been removed, so update the comment accordingly.
[rjw: Modified the subject and changelog slightly.]
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Support raw reads if all the registers being read are volatile, the cache
will have no impact for tem.
Support bulk reads either directly (if all the registers are volatile) or
by falling back to iterating over single register reads otherwise.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We only really need the defaults in order to cut down the number of
registers we sync and to satisfy reads while the device is powered off
but not all devices are going to need to do that (always on devices like
PMICs being the prime example) so don't require those devices to supply
a default. Instead only try to fall back to hardware defaults if the
driver told us to.
Devices using LZO won't be able to instantiate with this, that will require
some updates in the LZO code to handle this case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Simplify the check for registers set at their default value by avoiding
picking a default value in the case where we don't have one. Instead we
only compare the current value to the current value when we looked one
up. This fixes the case where we don't have a default stored but the value
was set to zero when that isn't the chip default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Ensure that when we start up in cache only mode we can store defaults of
zero, otherwise if the hardware is unavailable we won't be able to read.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
As with the bulk reads we really should be able to make these play
nicely with the cache but warn for now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
If a register isn't cached then let callers know that so they can fall
back or error handle appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Rather than open coding a binary search use the standard bsearch() using
the comparison function we're already using for sort() on insert. This
fixes a lockup I was observing due to iterating on min <= max rather
than min < max when we fail to look up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
* pm-domains:
PM / Domains: Split device PM domain data into base and need_restore
ARM: mach-shmobile: sh7372 sleep warning fixes
ARM: mach-shmobile: sh7372 A3SM support
ARM: mach-shmobile: sh7372 generic suspend/resume support
PM / Domains: Preliminary support for devices with power.irq_safe set
PM: Move clock-related definitions and headers to separate file
PM / Domains: Use power.sybsys_data to reduce overhead
PM: Reference counting of power.subsys_data
PM: Introduce struct pm_subsys_data
ARM / shmobile: Make A3RV be a subdomain of A4LC on SH7372
PM / Domains: Rename argument of pm_genpd_add_subdomain()
PM / Domains: Rename GPD_STATE_WAIT_PARENT to GPD_STATE_WAIT_MASTER
PM / Domains: Allow generic PM domains to have multiple masters
PM / Domains: Add "wait for parent" status for generic PM domains
PM / Domains: Make pm_genpd_poweron() always survive parent removal
PM / Domains: Do not take parent locks to modify subdomain counters
PM / Domains: Implement subdomain counters as atomic fields
* pm-runtime:
PM / Tracing: build rpm-traces.c only if CONFIG_PM_RUNTIME is set
PM / Runtime: Replace dev_dbg() with trace_rpm_*()
PM / Runtime: Introduce trace points for tracing rpm_* functions
PM / Runtime: Don't run callbacks under lock for power.irq_safe set
USB: Add wakeup info to debugging messages
PM / Runtime: pm_runtime_idle() can be called in atomic context
PM / Runtime: Add macro to test for runtime PM events
PM / Runtime: Add might_sleep() to runtime PM functions
To read the current PM QoS value for a given device we need to
make sure that the device's power.constraints object won't be
removed while we're doing that. For this reason, put the
operation under dev->power.lock and acquire the lock
around the initialization and removal of power.constraints.
Moreover, since we're using the value of power.constraints to
determine whether or not the object is present, the
power.constraints_state field isn't necessary any more and may be
removed. However, dev_pm_qos_add_request() needs to check if the
device is being removed from the system before allocating a new
PM QoS constraints object for it, so make it use the
power.power_state field of struct device for this purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since there are more lookups than insertions in a typical
scenario, optimize the linear search into a binary search. For
this to work, we need to keep reg_defaults sorted upon
insertions, for now be lazy and use sort().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch enables to register notifier_block for an OPP-device in order
to get notified for any changes in the availability of OPPs of the
device. For example, if a new OPP is inserted or enable/disable status
of an OPP is changed, the notifier is executed.
This enables the usage of opp_add, opp_enable, and opp_disable to
directly take effect with any connected entities such as cpufreq or
devfreq.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mike Turquette <mturquette@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Ensure we've got a function so users can enable/disable the
cache bypass option.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preperation for the upcoming patches, modify map->cache_bypass
directly. The helper functions will grab an exclusive lock. Because
we'll have acquired the same lock we need to avoid a deadlock.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We want to use regmap_write() to actually write anything
to the HW.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the handling of the cached rbnode into regcache_rbtree_lookup. This allows
us to remove of some duplicated code sections in regcache_rbtree_read and
regcache_rbtree_write.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use regcache_{set,get}_val in regcache_rbtree_{set,get}_register instead of
re-implementing its functionality.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch replaces dev_dbg with trace_rpm_* inside
the three important functions:
rpm_idle
rpm_suspend
rpm_resume
Trace points have the below advantages compared with dev_dbg:
- trace points include much runtime information(such as
running cpu, current task, ...)
- most of linux distributions may disable "verbose debug"
driver debug compile switch, so it is very difficult to
report/debug runtime pm related problems from distribution
users without this kind of debug information.
- for upstream kernel users, enableing the debug switch will
produce many useless "rpm_resume" output, and it is very noise.
- dev_dbg inside rpm_suspend/rpm_resume may have some effects
on runtime pm behaviour of console devicer
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The rpm_suspend() and rpm_resume() routines execute subsystem or PM
domain callbacks under power.lock if power.irq_safe is set for the
given device. This is inconsistent with that rpm_idle() does after
commit 02b2677 (PM / Runtime: Allow _put_sync() from
interrupts-disabled context) and is problematic for subsystems and PM
domains wanting to use power.lock for synchronization in their
runtime PM callbacks.
This change requires the code checking if the device's runtime PM
status is RPM_SUSPENDING or RPM_RESUMING to be modified too, to take
the power.irq_safe set case into account (that code wasn't reachable
before with power.irq_safe set, because it's executed with the
device's power.lock held).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
In the absence of a sync callback, do it manually. This of course
can't take advantange of the specific optimizations of each
cache type but it will do well enough in most cases.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When DEBUG_DRIVER is activated, be verbose and explicitly state when a
device<->driver match was rejected by the probe-function of the driver.
Now all code-paths report what is currently happening which helps
debugging, because you don't have to remember that no printout means
the match is rejected (and then you still don't know if it was because
of ENODEV or ENXIO).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The check to ensure that pages of recently added memory sections are correctly
marked as reserved before trying to online the memory is broken. The request
to online the memory fails with the following:
kernel: section number XXX page number 256 not reserved, was it already online?
This updates the page reservation checking to check the pages of each memory
section of the memory block being onlined individually.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sysfs memory probe interface allows unaligned regions
to be added:
# echo 0xffffff > /sys/devices/system/memory/probe
# cat /proc/iomem
00ffffff-01fffffe : System RAM
01ffffff-02fffffe : System RAM
02ffffff-03fffffe : System RAM
03ffffff-04fffffe : System RAM
04ffffff-05fffffe : System RAM
Return -EINVAL instead of creating these bad regions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The struct pm_domain_data data type is defined in such a way that
adding new fields specific to the generic PM domains code will
require include/linux/pm.h to be modified. As a result, data types
used only by the generic PM domains code will be defined in two
headers, although they all should be defined in pm_domain.h and
pm.h will need to include more headers, which won't be very nice.
For this reason change the definition of struct pm_subsys_data
so that its domain_data member is a pointer, which will allow
struct pm_domain_data to be subclassed by various PM domains
implementations. Remove the need_restore member from
struct pm_domain_data and make the generic PM domains code
subclass it by adding the need_restore member to the new data type.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Merge commit e8b364b88c
(PM / Clocks: Do not acquire a mutex under a spinlock) fixing
a regression in drivers/base/power/clock_ops.c.
Conflicts:
drivers/base/power/clock_ops.c
Commit b7ab83e (PM: Use spinlock instead of mutex in clock
management functions) introduced a regression causing clocks_mutex
to be acquired under a spinlock. This happens because
pm_clk_suspend() and pm_clk_resume() call pm_clk_acquire() under
pcd->lock, but pm_clk_acquire() executes clk_get() which causes
clocks_mutex to be acquired. Similarly, __pm_clk_remove(),
executed under pcd->lock, calls clk_put(), which also causes
clocks_mutex to be acquired.
To fix those problems make pm_clk_add() call pm_clk_acquire(), so
that pm_clk_suspend() and pm_clk_resume() don't have to do that.
Change pm_clk_remove() and pm_clk_destroy() to separate
modifications of the pcd->clock_list list from the actual removal of
PM clock entry objects done by __pm_clk_remove().
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch incorporates the regcache core code into regmap. All previous
patches have been no-ops essentially up to this point.
The bulk read operation is not supported by regcache at the moment. This
will be implemented incrementally.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for LZO compression when storing the register
cache.
For a typical device whose register map would normally occupy 25kB or 50kB
by using the LZO compression technique, one can get down to ~5-7kB. There
might be a performance penalty associated with each individual read/write
due to decompressing/compressing the underlying cache, however that should not
be noticeable. These memory benefits depend on whether the target architecture
can get rid of the memory occupied by the original register defaults cache
which is marked as __devinitconst. Nevertheless there will be some memory
gain even if the target architecture can't get rid of the original register
map, this should be around ~30-32kB instead of 50kB.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the rbtree cache compression type.
Each rbnode manages a variable length block of registers. There can be no
two nodes with overlapping blocks. Each block has a base register and a
currently top register, all the other registers, if any, lie in between these
two and in ascending order.
The reasoning behind the construction of this rbtree is simple. In the
snd_soc_rbtree_cache_init() function, we iterate over the register defaults
provided by the regcache core. For each register value that is non-zero we
insert it in the rbtree. In order to determine in which rbnode we need
to add the register, we first look if there is another register already
added that is adjacent to the one we are about to add. If that is the case
we append it in that rbnode block, otherwise we create a new rbnode
with a single register in its block and add it to the tree.
There are various optimizations across the implementation to speed up lookups
by caching the most recently used rbnode.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the simplest form of a cache available in regcache. Any
registers whose default value is 0 are ignored. If any of those
registers are modified in the future, they will be placed in the
cache on demand. The cache layout is essentially using the provided
register defaults by the regcache core directly and does not re-map
it to another representation.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch introduces caching support for regmap. The regcache API
has evolved essentially out of ASoC soc-cache so most of the actual
caching types (except LZO) have been tested in the past.
The purpose of regcache is to optimize in time and space the handling
of register caches. Time optimization is achieved by not having to go
over a slow bus like I2C to read the value of a register, instead it is
cached locally in memory and can be retrieved faster. Regarding space
optimization, some of the cache types are better at packing the caches,
for e.g. the rbtree and the LZO caches. By doing this the sacrifice in
time still wins over doing I2C transactions.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make the debugfs stubs static inline to avoid future compilation issues due to
duplicated symbols when CONFIG_DEBUG_FS=n once internal.h is included by
multiple source files.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some buses like SPI have no standard notation of read or write operations.
The general scheme here is to set or clear specific bits in the register
address to indicate whether the operation is a read or write. We already
support having a read flag mask per bus, but as there is no standard
the bits which need to be set or cleared differ between devices and vendors,
thus we need a mechanism to specify them per device.
This patch adds two new entries to the regmap_config struct, read_flag_mask and
write_flag_mask. These will be or'ed onto the top byte when doing a read or
write operation. If both masks are empty the device will fallback to the
regmap_bus masks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No longer used as users link directly with the bus types so the core
module infrastructure does refcounting for us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The conversion to per bus type registration functions means we don't need
to do module_get()s to hold the bus types in memory (their users will link
to them) so we removed all those calls. This left module_put() calls in
the cleanup paths which aren't needed and which cause unbalanced puts if
we ever try to unload anything.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
compared to the most powerful and already existing helper (namely
platform_device_register_resndata) this allows to specify a dma_mask.
To make eventual extensions later more easy, a struct holding the used
information is created instead of passing the information by function
parameters.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The generic PM domains framework currently doesn't work with devices
whose power.irq_safe flag is set, because runtime PM callbacks for
such devices are run with interrupts disabled and the callbacks
provided by the generic PM domains framework use domain mutexes
and may sleep. However, such devices very well may belong to
power domains on some systems, so the generic PM domains framework
should take them into account.
For this reason, modify the generic PM domains framework so that the
domain .power_off() and .power_on() callbacks are never executed for
a domain containing devices with power.irq_safe set, although the
.stop_device() and .start_device() callbacks are still run for them.
Additionally, introduce a flag allowing the creator of a
struct generic_pm_domain object to indicate that its .stop_device()
and .start_device() callbacks may be run in interrupt context
(might_sleep_if() triggers if that flag is not set and one of those
callbacks is run in interrupt context).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a global notification chain that gets called upon changes to the
aggregated constraint value for any device.
The notification callbacks are passing the full constraint request data
in order for the callees to have access to it. The current use is for the
platform low-level code to access the target device of the constraint.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Implement the per-device PM QoS constraints by creating a device
PM QoS API, which calls the PM QoS constraints management core code.
The per-device latency constraints data strctures are stored
in the device dev_pm_info struct.
The device PM code calls the init and destroy of the per-device constraints
data struct in order to support the dynamic insertion and removal of the
devices in the system.
To minimize the data usage by the per-device constraints, the data struct
is only allocated at the first call to dev_pm_qos_add_request.
The data is later free'd when the device is removed from the system.
A global mutex protects the constraints users from the data being
allocated and free'd.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since the PM clock management code in drivers/base/power/clock_ops.c
is used for both runtime PM and system suspend/hibernation, the
definitions of data structures and headers related to it should not
be located in include/linux/pm_rumtime.h. Move them to a separate
header file.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently pm_genpd_runtime_resume() has to walk the list of devices
from the device's PM domain to find the corresponding device list
object containing the need_restore field to check if the driver's
.runtime_resume() callback should be executed for the device.
This is suboptimal and can be simplified by using power.sybsys_data
to store device information used by the generic PM domains code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since the power.subsys_data device field will be used by multiple
filesystems, introduce a reference counting mechanism for it to avoid
freeing it prematurely or changing its value at a wrong time.
Make the PM clocks management code that currently is the only user of
power.subsys_data use the new reference counting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce struct pm_subsys_data that may be subclassed by subsystems
to store subsystem-specific information related to the device. Move
the clock management fields accessed through the power.subsys_data
pointer in struct device to the new strucutre.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the name of the second argument of pm_genpd_add_subdomain()
so that it is (a) shorter and (b) in agreement with the name of
the second argument of pm_genpd_add_subdomain().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since it is now possible for a PM domain to have multiple masters
instead of one parent, rename the "wait for parent" status to reflect
the new situation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, for a given generic PM domain there may be only one parent
domain (i.e. a PM domain it depends on). However, there is at least
one real-life case in which there should be two parents (masters) for
one PM domain (the A3RV domain on SH7372 turns out to depend on the
A4LC domain and it depends on the A4R domain and the same time). For
this reason, allow a PM domain to have multiple parents (masters) by
introducing objects representing links between PM domains.
The (logical) links between PM domains represent relationships in
which one domain is a master (i.e. it is depended on) and another
domain is a slave (i.e. it depends on the master) with the rule that
the slave cannot be powered on if the master is not powered on and
the master cannot be powered off if the slave is not powered off.
Each struct generic_pm_domain object representing a PM domain has
two lists of links, a list of links in which it is a master and
a list of links in which it is a slave. The first of these lists
replaces the list of subdomains and the second one is used in place
of the parent pointer.
Each link is represented by struct gpd_link object containing
pointers to the master and the slave and two struct list_head
members allowing it to hook into two lists (the master's list
of "master" links and the slave's list of "slave" links). This
allows the code to get to the link from each side (either from
the master or from the slave) and follow it in each direction.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The next patch will make it possible for a generic PM domain to have
multiple parents (i.e. multiple PM domains it depends on). To
prepare for that change it is necessary to change pm_genpd_poweron()
so that it doesn't jump to the start label after running itself
recursively for the parent domain. For this purpose, introduce a new
PM domain status value GPD_STATE_WAIT_PARENT that will be set by
pm_genpd_poweron() before calling itself recursively for the parent
domain and modify the code in drivers/base/power/domain.c so that
the GPD_STATE_WAIT_PARENT status is guaranteed to be preserved during
the execution of pm_genpd_poweron() for the parent.
This change also causes pm_genpd_add_subdomain() and
pm_genpd_remove_subdomain() to wait for started pm_genpd_poweron() to
complete and allows pm_genpd_runtime_resume() to avoid dropping the
lock after powering on the PM domain.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If pm_genpd_remove_subdomain() is called to remove a PM domain's
subdomain and pm_genpd_poweron() is called for that subdomain at
the same time, and the pm_genpd_poweron() called by it recursively
for the parent returns an error, the first pm_genpd_poweron()'s
error code path will attempt to decrement the subdomain counter of
a PM domain that it's not a subdomain of any more.
Rearrange the code in pm_genpd_poweron() to prevent this from
happening.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
After the subdomain counter in struct generic_pm_domain has been
changed into an atomic_t field, it is possible to modify
pm_genpd_poweron() and pm_genpd_poweroff() so that they don't take
the parents locks. This requires pm_genpd_poweron() to increment
the parent's subdomain counter before calling itself recursively
for the parent and to decrement it if an error is to be returned.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, pm_genpd_poweron() and pm_genpd_poweroff() need to take
the parent PM domain's lock in order to modify the parent's counter
of active subdomains in a nonracy way. This causes the locking to be
considerably complex and in fact is not necessary, because the
subdomain counters may be implemented as atomic fields and they
won't have to be modified under a lock.
Replace the unsigned in sd_count field in struct generic_pm_domain
by an atomic_t one and modify the code in drivers/base/power/domain.c
to take this change into account.
This patch doesn't change the locking yet, that is going to be done
in a separate subsequent patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In commit a144c6a6c9 ("PM: Print a warning if firmware is requested
when tasks are frozen") we not only printed a warning if somebody tried
to load the firmware when tasks are frozen - we also failed the load.
But that check was done before the check for built-in firmware, and then
when we disallowed usermode helpers during bootup (commit 288d5abec831:
"Boot up with usermodehelper disabled"), that actually means that
built-in modules can no longer load their firmware even if the firmware
is built in too. Which used to work, and some people depended on it for
the R100 driver.
So move the test for usermodehelper_is_disabled() down, to after
checking the built-in firmware.
This should fix:
https://bugzilla.kernel.org/show_bug.cgi?id=40952
Reported-by: James Cloos <cloos@hjcloos.com>
Bisected-by: Elimar Riesebieter <riesebie@lxtec.de>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Rafael Wysocki <rjw@sisk.pl>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lock member of struct pm_clk_data is of type struct mutex,
which is a problem, because the suspend and resume routines
defined in drivers/base/power/clock_ops.c cannot be executed
with interrupts disabled for this reason. Modify
struct pm_clk_data so that its lock member is a spinlock.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Unlike dynamic_pr_debug, dynamic uses of dev_dbg can not
currently add task_pid/KBUILD_MODNAME/__func__/__LINE__
to selected debug output.
Add a new function similar to dynamic_pr_debug to
optionally emit these prefixes.
Cc: Aloisio Almeida <aloisio.almeida@openbossa.org>
Noticed-by: Aloisio Almeida <aloisio.almeida@openbossa.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If id_entry is available then it is used. However if we remove first the
driver followed by the device, then the id_entry is pointing to driver's
memory which is long gone.
Since id->name and plat->name are equal there is no point in
distinguishing them.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
devres_release_all and devres_release_group both aquire the lock
&dev->devres_lock but the release of that lock is done in release_nodes.
This results in sparse noise about context imbalance.
Add a lock annotation to release_nodes to quiet this noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit b33f9cbd67 ("regmap: Specify a module license") added a
MODULES_LICENSE to this file without adding an include of module.h.
module.h should have been included anyway, since this file has
EXPORT_SYMBOLs as well. With the pending module.h split up, this would
probably have caused build problems.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the entry points to pm runtime are not safe to
call in atomic context unless pm_runtime_irq_safe() has
been called. Inspecting the code, it is not immediately
obvious that the functions sleep at all, as they run
inside a spin_lock_irqsave, but under some conditions
they can drop the lock and turn on irqs.
If a driver incorrectly calls the pm_runtime apis, it can
cause sleeping and irq processing when it expects to stay
in atomic context.
Add might_sleep_if to the majority of the __pm_runtime_* entry points
to enforce correct usage.
Add pm_runtime_put_sync_autosuspend to the list of
functions that can be called in atomic context.
Signed-off-by: Colin Cross <ccross@android.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Function genpd_queue_power_off_work() is not defined for
CONFIG_PM_RUNTIME, so pm_genpd_poweroff_unused() causes a build
error to happen in that case. Fix the problem by making
pm_genpd_poweroff_unused() depend on CONFIG_PM_RUNTIME too.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Let userspace know what the access map for the device is. This is helpful
for verifying that the access map is correctly configured and could also
be useful for programs that try to work with the data. File format is:
register: R W V P
where R, W, V and P are 'y' or 'n' showing readable, writable, volatile
and precious respectively.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're going to be using these in quite a few places so factor out the
readable/writable/volatile/precious checks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_REGMAP_I2C/SPI are set to m when selected by a tristate config
option that's set to m. The regmap modules don't specify a license, so
fail to link to regmap_init at load time, since that is EXPORT_SYMBOL_GPL.
Fix this by specifying a license for the regmap modules.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
x86_64 size_t is not an int but the printf format specifier for size_t
should be an int.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
This fixes the following section mismatch issue:
WARNING: vmlinux.o(.text+0x1192bf): Section mismatch in reference from the function devtmpfsd() to the variable .init.data:setup_done
The function devtmpfsd() references the variable __initdata setup_done.
This is often because devtmpfsd lacks a __initdata annotation or the annotation of setup_done is wrong.
WARNING: vmlinux.o(.text+0x119342): Section mismatch in reference from the function devtmpfsd() to the variable .init.data:setup_done
The function devtmpfsd() references the variable __initdata setup_done.
This is often because devtmpfsd lacks a __initdata annotation or the annotation of setup_done is wrong.
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Warning(drivers/base/platform.c:50): No description found for parameter 'pdev'
Warning(drivers/base/platform.c:50): Excess function parameter 'dev' description in 'arch_setup_pdev_archdata'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Copy over the read parts of the ASoC debugfs implementation into regmap,
allowing users to see what the register values the device has are at
runtime. The implementation, especially the support for seeking, is
mostly due to Dimitris Papastamos' work in ASoC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is mainly intended to be used by devices which can dynamically
block register writes at runtime, for other devices there is usually
limited value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Trace single register reads and writes, plus start/stop tracepoints for
the actual I/O to see where we're spending time. This makes it easy to
have always on logging without overwhelming the logs and also lets us take
advantage of all the context and time information that the trace subsystem
collects for us.
We don't currently trace register values for bulk operations as this would
add complexity and overhead parsing the cooked data that's being worked
with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When doing a single register write we use work_buf for both the register
and the value with the buffer formatted for sending directly to the device
so we can just do a write() directly. This saves allocating a temporary
buffer if we can't do gather writes and is likely to be faster than doing
a gather write.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is currently unused but we need to know which registers exist and
their properties in order to implement diagnostics like register map
dumps and the cache features.
We use callbacks partly because properties can vary at runtime (eg, through
access locks on registers) and partly because big switch statements are a
good compromise between readable code and small data size for providing
information on big register maps.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the use of pm_runtime_put_sync() is not safe from
interrupts-disabled context because rpm_idle() will release the
spinlock and enable interrupts for the idle callbacks. This enables
interrupts during a time where interrupts were expected to be
disabled, and can have strange side effects on drivers that expected
interrupts to be disabled.
This is not a bug since the documentation clearly states that only
_put_sync_suspend() is safe in IRQ-safe mode.
However, pm_runtime_put_sync() could be made safe when in IRQ-safe
mode by releasing the spinlock but not re-enabling interrupts, which
is what this patch aims to do.
Problem was found when using some buggy drivers that set
pm_runtime_irq_safe() and used _put_sync() in interrupts-disabled
context.
Reported-by: Colin Cross <ccross@google.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The local variable ret is defined twice in pm_genpd_poweron(), which
causes this function to always return 0, even if the PM domain's
.power_on() callback fails, in which case an error code should be
returned.
Remove the wrong second definition of ret and additionally remove an
unnecessary definition of wait from pm_genpd_poweron().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
create_path() on something without a single / in it will return err
without initializing it. It actually can't happen (we call that thing
only if create on the same path returns -ENOENT, which won't happen
happen for single-component path), but in this case initializing err
to 0 is more than making compiler to STFU - would be the right thing
to return on such paths; the function creates a parent directory of
given pathname and in that case it has no work to do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dev_opp initial value shoule be ERR_PTR(), IS_ERR() is used to check
error.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
updated Documentation/ja_JP/SubmittingPatches
debugfs: add documentation for debugfs_create_x64
uio: uio_pdrv_genirq: Add OF support
firmware: gsmi: remove sysfs entries when unload the module
Documentation/zh_CN: Fix messy code file email-clients.txt
driver core: add more help description for "path to uevent helper"
driver-core: modify FIRMWARE_IN_KERNEL help message
driver-core: Kconfig grammar corrections in firmware configuration
DOCUMENTATION: Replace create_device() with device_create().
DOCUMENTATION: Update overview.txt in Doc/driver-model.
pti: pti_tty_install documentation mispelling.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: take the ACL checks to common code
bury posix_acl_..._masq() variants
kill boilerplates around posix_acl_create_masq()
generic_acl: no need to clone acl just to push it to set_cached_acl()
kill boilerplate around posix_acl_chmod_masq()
reiserfs: cache negative ACLs for v1 stat format
xfs: cache negative ACLs if there is no attribute fork
9p: do no return 0 from ->check_acl without actually checking
vfs: move ACL cache lookup into generic code
CIFS: Fix oops while mounting with prefixpath
xfs: Fix wrong return value of xfs_file_aio_write
fix devtmpfs race
caam: don't pass bogus S_IFCHR to debugfs_create_...()
get rid of create_proc_entry() abuses - proc_mkdir() is there for purpose
asus-wmi: ->is_visible() can't return negative
fix jffs2 ACLs on big-endian with 16bit mode_t
9p: close ACL leaks
ocfs2_init_acl(): fix a leak
VFS : mount lock scalability for internal mounts
After we's done complete(&req->done), there's nothing to prevent the
scope containing *req from being gone and *req overwritten by any
kind of junk. So we must read req->next before that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We should be reading the number of bytes we were asked for, not the size
of a single register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regulator: Convert tps65023 to use regmap API
regmap: Add SPI bus support
regmap: Add I2C bus support
regmap: Add generic non-memory mapped register access API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
There are many places in the tree where we implement register access for
devices on non-memory mapped buses, especially I2C and SPI. Since hardware
designers seem to have settled on a relatively consistent set of register
interfaces this can be effectively factored out into shared code. There
are a standard set of formats for marshalling data for exchange with the
device, with the actual I/O mechanisms generally being simple byte
streams.
We create an abstraction for marshaling data into formats which can be
sent on the control interfaces, and create a standard method for
plugging in actual transport underneath that.
This is mostly a refactoring and renaming of the bottom level of the
existing code for sharing register I/O which we have in ASoC. A
subsequent patch in this series converts ASoC to use this. The main
difference in interface is that reads return values by writing to a
location provided by a pointer rather than in the return value, ensuring
we can use the full range of the type for register data. We also use
unsigned types rather than ints for the same reason.
As some of the devices can have very large register maps the existing
ASoC code also contains infrastructure for managing register caches.
This cache work will be moved over in a future stage to allow for
separate review, the current patch only deals with the physical I/O.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
iommu/core: Fix build with INTR_REMAP=y && CONFIG_DMAR=n
iommu/amd: Don't use MSI address range for DMA addresses
iommu/amd: Move missing parts to drivers/iommu
iommu: Move iommu Kconfig entries to submenu
x86/ia64: intel-iommu: move to drivers/iommu/
x86: amd_iommu: move to drivers/iommu/
msm: iommu: move to drivers/iommu/
drivers: iommu: move to a dedicated folder
x86/amd-iommu: Store device alias as dev_data pointer
x86/amd-iommu: Search for existind dev_data before allocting a new one
x86/amd-iommu: Allow dev_data->alias to be NULL
x86/amd-iommu: Use only dev_data in low-level domain attach/detach functions
x86/amd-iommu: Use only dev_data for dte and iotlb flushing routines
x86/amd-iommu: Store ATS state in dev_data
x86/amd-iommu: Store devid in dev_data
x86/amd-iommu: Introduce global dev_data_list
x86/amd-iommu: Remove redundant device_flush_dte() calls
iommu-api: Add missing header file
Fix up trivial conflicts (independent additions close to each other) in
drivers/Makefile and include/linux/pci.h
We do _NOT_ want to mkdir the path itself - we are preparing to
mknod it, after all. Normally it'll fail with -ENOENT and
just do nothing, but if somebody has created the parent in
the meanwhile, we'll get buggered...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... and give it a namespace where devtmpfs would be mounted on root,
thus avoiding abuses of vfs_path_lookup() (it was never intended to
be used with LOOKUP_PARENT). Games with credentials are also gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* pm-runtime:
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Runtime: Consistent utilization of deferred_resume
PM / Runtime: Prevent runtime_resume from racing with probe
PM / Runtime: Replace "run-time" with "runtime" in documentation
PM / Runtime: Improve documentation of enable, disable and barrier
PM: Limit race conditions between runtime PM and system sleep (v2)
PCI / PM: Detect early wakeup in pci_pm_prepare()
PM / Runtime: Return special error code if runtime PM is disabled
PM / Runtime: Update documentation of interactions with system sleep
* pm-domains: (33 commits)
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
PM / Domains: Make failing pm_genpd_prepare() clean up properly
PM / Domains: Set device state to "active" during system resume
ARM: mach-shmobile: sh7372 A3RV requires A4LC
PM / Domains: Export pm_genpd_poweron() in header
ARM: mach-shmobile: sh7372 late pm domain off
ARM: mach-shmobile: Runtime PM late init callback
ARM: mach-shmobile: sh7372 D4 support
ARM: mach-shmobile: sh7372 A4MP support
ARM: mach-shmobile: sh7372: make sure that fsi is peripheral of spu2
ARM: mach-shmobile: sh7372 A3SG support
...
Some users are apparently confused by dmesg output from
read_magic_time(), which looks like "real" time and date.
Add the "RTC" string to time stamps printed by read_magic_time() to
avoid that confusion.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
cpufreq table allocated by opp_init_cpufreq_table is better
freed by OPP layer itself. This allows future modifications to
the table handling to be transparent to the users.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently pm_genpd_poweroff() discards error codes returned by
the PM domain's .power_off() callback, because it's safer to always
regard the domain as inaccessible to drivers after a failing
.power_off(). Still, there are situations in which the low-level
code may want to indicate that it doesn't want to power off the
domain, so allow it to do that by returning -EBUSY from .power_off().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make pd_power_down_a3rv() use genpd_queue_power_off_work() to queue
up the powering off of the A4LC domain to avoid queuing it up when
it is pending.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Mark Brown