If an existing rbd client is found to be suitable for use in
rbd_get_client(), the rbd_options structure is not being
freed as it should. Fix that.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
The Netlogic XLP SoC's on-chip USB controller appears as a PCI
USB device, but does not need the EHCI/OHCI handoff done in
usb/host/pci-quirks.c.
The pci-quirks.c is enabled for all vendors and devices, and is
enabled if USB and PCI are configured.
If we do not skip the qurik handling on XLP, the readb() call in
ehci_bios_handoff() will cause a crash since byte access is not
supported for EHCI registers in XLP.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when missing USB PHY clock, kernel booting up will halt during USB
initialization. We should check USBGP[PHY_CLK_VALID] bit to avoid
CPU hang in this case.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This otg driver depends on marvell EHCI driver, so add the dependence.
It can fix the following build error on i386:
ERROR: "usb_remove_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
ERROR: "usb_add_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distinguish Kconfig text by providing the Freescale family name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/blit: fix blit copy for very large buffers
drm/radeon/kms: fix TRAVIS panel setup
drm/radeon: fix use after free in ATRM bios reading code.
drm/radeon/kms: Fix device tree linkage of DP i2c buses too
drm/radeon: Set DESKTOP_HEIGHT register to the framebuffer (not mode) height.
drm/radeon/kms: disable output polling when suspended
drm/nv50/pm: signedness bug in nv50_pm_clocks_pre()
drm/nouveau/gem: fix fence_sync race / oops
drm/nouveau: fix typo on mxmdcb option
drm/nouveau/mxm: pretend to succeed, even if we can't shadow the MXM-SIS
drm/nouveau/disp: check that panel power gpio is enabled at init time
Evergreen and NI blit copy was broken if the buffer maps to a rectangle
whose one dimension is 16384 (max dimension allowed by these chips).
In the mainline kernel, the problem is exposed only when buffers are
very large (1G), but it's still a problem. The problem could be exposed
for smaller buffers if anyone modifies the algorithm for rectangle
construction in r600_blit_create_rect() (the reason why someone would
modify that algorithm is to tune the performance of buffer moves).
The root cause was in i2f() function which only operated on range between
0 and 16383. Fix this by extending the range of i2f() function to 0 to
32767.
While at it improve the function so that the range can be easily
extended in the future (if it becomes necessary), cleanup lines
over 80 characters, and replace in-line comments with one strategic
comment that explains the crux of the function.
Credits to michel@daenzer.net for pointing out the root cause of
the bug.
v2: Fix I2F_MAX_INPUT constant definition goof and warn only once
if input argument is out of range. Edit the comment a little
bit to avoid some linguistic confusion and make it look better
in general.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Different versions of the DP to LVDS bridge chip
need different panel mode settings depending on
the chip version used.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41569
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 6584cb88 (ARM i.MX dma: Fix burstsize settings) fixed
the mxcmmc driver but forgot to fix the SDMA driver to handle the
correct burtsize.
This make the SD card access works again with DMA on i.MX31 boards.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This bug was introduced by commit 54be5663
"gpio-ml-ioh: Support interrupt function" which adds a spinlock to struct
ioh_gpio but never init the spinlock.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This bug was introduced by commit d568a681
"gpio-pch: add spinlock in suspend/resume processing"
which adds a spinlock to struct pch_gpio but never init the spinlock.
Reported-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add workarounds table entries for hardware bugs in
- FireWire part of Sound Blaster Audigy cards,
- Ricoh PCIe 1394 controllers.
Without these, several protocols, e.g. AV/C, do not work on the
Audigy, and the Ricoh PCIe controllers wouldn't work at all.
This does not concern the older Ricoh PCI controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=3Utr
-----END PGP SIGNATURE-----
Merge tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
firewire fixes post v3.3-rc1
Add workarounds table entries for hardware bugs in
- FireWire part of Sound Blaster Audigy cards,
- Ricoh PCIe 1394 controllers.
Without these, several protocols, e.g. AV/C, do not work on the
Audigy, and the Ricoh PCIe controllers wouldn't work at all.
This does not concern the older Ricoh PCI controllers.
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: disable MSI on Ricoh controllers
firewire: ohci: add reset packet quirk for SB Audigy
Add MODULE_LICENSE() as per the license in the comment at the top of the
file for this source module to fix build warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/staging/media/go7007/go7007-usb.o
see include/linux/module.h for more information
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ross Cohen <rcohen@snurgle.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As ZTE have and will use more pid for new products this year,
so we need to add some new zte 3g-dongle's pid on option.c ,
and delete one pid 0x0154 because it use for mass-storage port.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 15c9a0acc3 (of: create of_phandle_args to simplify return of phandle
parsing data) modifies the parameter list of of_xlate function pointer declaration
in gpio_chip. Adapt the gpio specifier translate function for this change.
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We've found that qcserial devices will not always wake up reliably
from autosuspend, so disable it.
Signed-off-by: Thomas Tuttle <ttuttle@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Fix a crash due to a regression (uninitialized refcnt) introduced in
3.2 with XRC support.
- Close race in how ucma reports events when connect fails.
- Process vendor-specific MADs in mlx4 so that eg FDR-10 data rate works.
- Fix regression in qib caused by over-aggressive PCIe tuning.
- Other small fixes for hardware drivers (ipath, nes, qib).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABCAAGBQJPKNzJAAoJEENa44ZhAt0heQsP/1XmbosLnTZ3RFmEFcvW4Akn
lCuxPqvF7tfMXzl4fkYOZ0bNvfB4xTbMVkWeQXnwK+e2p/kL8a/dWHaom79wgo7Z
qAldncGAZrXEn8E3IcHLgWKMtHK9/HpJZvxkqlACa7muQKunS41Qa/QqIL5MoUQm
PVsTkj3wjtdvN5XgrtmeY2efTY86tZDxDv8Glg76616SawsJ/J17FRMNAEl02vZ5
mFH2jtmlsSNNenwSkykwEJpX39teqLl/GreAKuxt2pZXhGi67aFcfu7OrS9LY5iy
LNP5a+gmykOAjq+dx9DGj24LRD4+pisDXb851e2tcZ1l1jrgedBGTqPWXldR0acq
+eFYmYmIGU7iFQZvKel9PFiPa2YEUZn8TtKN+e1vSkXqsLuI1qjBVf+i2fMUwszB
TyxRjX62S9J01CY5XKlBySAAoVWcf2NyP6IKAIF4nOKXR5g4KtMUmmkL5BamV/7c
YodAey8+0RTqLY2tgj0WKIswVAHg1ALXo8AzFwQRioau9Ro+T+2UsSzR6WzKpF7B
uhAyZynW8zNb7esSuXiiD5PfI4+gUlEyeesxuRFhufp45i3NQhhkW+6bRM5m0YkJ
MMww5UyFnXqiEiCrB35rAio+MrhIHLMYXP5/oPNblgYlRWpSN9ijnyeDrVN9D0aX
3BS5gakUhRntjwFcOz54
=81hM
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
InfiniBand/RDMA fixes for 3.3:
- Fix a crash due to a regression (uninitialized refcnt) introduced in
3.2 with XRC support.
- Close race in how ucma reports events when connect fails.
- Process vendor-specific MADs in mlx4 so that eg FDR-10 data rate works.
- Fix regression in qib caused by over-aggressive PCIe tuning.
- Other small fixes for hardware drivers (ipath, nes, qib).
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Copyright update
IB/mlx4: pass SMP vendor-specific attribute MADs to firmware
RDMA/nes: Fix fast memory registration opcode
RDMA/nes: Fix fast memory registration length
RDMA/ucma: Discard all events for new connections until accepted
IB/qib: Roll back PCIe tuning change
IB/qib: Use GFP_ATOMIC when locks are held
RDMA/nes: Add missing rcu_read_unlock() in nes_addr_resolve_neigh()
RDMA/nes: Fix for sending MPA reject frame
IB/ipath: Calling PTR_ERR() on right variable in create_file()
RDMA/core: Fix kernel panic by always initializing qp->usecnt
serio_raw_read now returns (sometimes partially) successful number of
bytes transferred to the caller, and only returns error code to the
caller on completely failed transfers.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 509f87c5f5 (evdev - do not block waiting for an event if fd
is nonblock) created a code path were it was possible to use retval
uninitialized.
This could lead to the xorg evdev input driver getting corrupt data
and refusing to work with log messages like
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
(for drivers auo-pixcir-ts and gpio-keys).
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a flag to allow platforms to specify, whether a DMAC instance supports
the MEMCPY operation. To avoid regressions, preserve the current default.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Properly set the parent device of DP i2c buses before registering them
too.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The value of this register is transferred to the V_COUNTER register at the
beginning of vertical blank. V_COUNTER is the reference for VLINE waits and
goes from VIEWPORT_Y_START to VIEWPORT_Y_START+VIEWPORT_HEIGHT during scanout,
so if VIEWPORT_Y_START is not 0, V_COUNTER actually went backwards at the
beginning of vertical blank, and VLINE waits excluding the whole scanout area
could never finish (possibly only if VIEWPORT_Y_START is larger than the length
of vertical blank in scanlines). Setting DESKTOP_HEIGHT to the framebuffer
height should prevent this for any kind of VLINE wait.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=45329 .
CC: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Polling the outputs when the device is suspended can result in erroneous
status updates. Disable output polling during suspend to prevent this
from happening.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
calc_mclk() returns zero on success and negative on failure but clk is
a u32.
v2: Martin Peres:
- clk should be an int, not a u32
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's at least one known case where our shadowing code is buggy, and we
fail init. Until we can be confident we're doing all this correctly, lets
succeed and risk crazy bios tables rather than failing for perfectly valid
configs too.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
commit 463894705e deleted redundant
chan_id and chancnt initialization in dma drivers as this is done
in dma_async_device_register().
However, atc_enable_irq() relied on chan_id set before registering
the device, what left only channel 0 functional for this driver.
This patch introduces atc_enable/disable_chan_irq() as a variant
of atc_enable/disable_irq() with the channel as explicit argument.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (w83627ehf) Disable setting DC mode for pwm2, pwm3 on NCT6776F
hwmon: (sht15) fix bad error code
MAINTAINERS: Drop maintainer for MAX1668 hwmon driver
MAINTAINERS: Add hwmon entries for Wolfson
hwmon: (f71805f) Fix clamping of temperature limits
Here are some fixes to the pin control system that has accumulated since
-rc1. Mainly Tony Lindgren fixed the module load/unload logic and the
rest are minor fixes and documentation.
* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: add checks for empty function names
pinctrl: fix pinmux_hog_maps when ctrl_dev_name is not set
pinctrl: fix some pinmux typos
pinctrl: free debugfs entries when unloading a pinmux driver
pinctrl: unbreak error messages
Documentation/pinctrl: fix a few syntax errors in code examples
pinctrl: fix pinconf_pins_show iteration
Update copyright information in the source files.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In the current code, vendor-specific MADs (e.g with the FDR-10
attribute) are silently dropped by the driver, resulting in timeouts
at the sending side and inability to query/configure the relevant
feature. However, the ConnectX firmware is able to handle such MADs.
For unsupported attributes, the firmware returns a GET_RESPONSE MAD
containing an error status.
For example, for a FDR-10 node with LID 11:
# ibstat mlx4_0 1
CA: 'mlx4_0'
Port 1:
State: Active
Physical state: LinkUp
Rate: 40 (FDR10)
Base lid: 11
LMC: 0
SM lid: 24
Capability mask: 0x02514868
Port GUID: 0x0002c903002e65d1
Link layer: InfiniBand
Extended Port Query (EPI) vendor mad timeouts before the patch:
# smpquery MEPI 11 -d
ibwarn: [4196] smp_query_via: attr 0xff90 mod 0x0 route Lid 11
ibwarn: [4196] _do_madrpc: retry 1 (timeout 1000 ms)
ibwarn: [4196] _do_madrpc: retry 2 (timeout 1000 ms)
ibwarn: [4196] _do_madrpc: timeout after 3 retries, 3000 ms
ibwarn: [4196] mad_rpc: _do_madrpc failed; dport (Lid 11)
smpquery: iberror: [pid 4196] main: failed: operation EPI: ext port info query failed
EPI query works OK with the patch:
# smpquery MEPI 11 -d
ibwarn: [6548] smp_query_via: attr 0xff90 mod 0x0 route Lid 11
ibwarn: [6548] mad_rpc: data offs 64 sz 64
mad data
0000 0000 0000 0001 0000 0001 0000 0001
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
# Ext Port info: Lid 11 port 0
StateChangeEnable:...............0x00
LinkSpeedSupported:..............0x01
LinkSpeedEnabled:................0x01
LinkSpeedActive:.................0x01
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Ira Weiny <weiny2@llnl.gov>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Big thing here is the movement of the 8250 serial drivers to their own
directory, now that the patch churn has calmed down.
Other than that, only minor stuff (omap patches were reverted as they
were found to be wrong), and another broken driver removed from the
system.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk8nB3wACgkQMUfUDdst+ykJAgCeKirJzWs6KrXMX6TWSabSvvsX
xbUAn2mnT+UooWSDawrACknkDsQ7y41n
=9tuj
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Here are some tty/serial patches for 3.3-rc1
Big thing here is the movement of the 8250 serial drivers to their own
directory, now that the patch churn has calmed down.
Other than that, only minor stuff (omap patches were reverted as they
were found to be wrong), and another broken driver removed from the
system.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* tag 'tty-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: Kill off Moorestown code
Revert "tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode"
Revert "tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip"
serial: Fix wakeup init logic to speed up startup
docbook: don't use serial_core.h in device-drivers book
serial: amba-pl011: lock console writes against interrupts
amba-pl011: do not disable RTS during shutdown
tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip
tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode
omap-serial: make serial_omap_restore_context depend on CONFIG_PM_RUNTIME
omap-serial :Make the suspend/resume functions depend on CONFIG_PM_SLEEP.
TTY: fix UV serial console regression
jsm: Fixed EEH recovery error
Updated TTY MAINTAINERS info
serial: group all the 8250 related code together
The life cycle of a device-mapper target is:
1) create
2) resume
3) suspend
*) possibly repeat from 2
4) destroy
The dm-raid target is unconditionally calling MD's bitmap_load function upon
every resume. If steps 2 & 3 above are repeated, bitmap_load is called
multiple times. It is only written to be called once; otherwise, it allocates
new memory for the bitmap (without freeing the old) and incrementing the number
of pages it thinks it has without zeroing first. This ultimately leads to
access beyond allocated memory and lost memory.
Simply avoiding the bitmap_load call upon resume is not sufficient. If the
target was suspended while the initial recovery was only partially complete,
it needs to be restarted when the target is resumed. This is why
'md_wakeup_thread' is called before issuing the 'mddev_resume'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The PCIe device
FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd FireWire Host Controller
[1180:e832] (prog-if 10 [OHCI])
is unable to access attached FireWire devices when MSI is enabled but
works if MSI is disabled.
http://www.mail-archive.com/alsa-user@lists.sourceforge.net/msg28251.html
Hence add the "disable MSI" quirks flag for this device, or in fact for
safety and simplicity for all current (R5U230, R5U231, R5U240) and
future Ricoh PCIe 1394 controllers.
Reported-by: Stefan Thomas <kontrapunktstefan@googlemail.com>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Nothing major, largest thing here is the removal of some drivers that
did not work at all. Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk8m8JEACgkQMUfUDdst+ymCFQCeNhTHopHy1PQbuCDwk8bSH4DW
1/YAn2k0YaaCrOo0HCzOslAVX18vGnWl
=TNNB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Here are a bunch of USB patches for 3.3-rc1.
Nothing major, largest thing here is the removal of some drivers that
did not work at all. Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (52 commits)
uwb & wusb: fix kconfig error
USB: Realtek cr: fix autopm scheduling while atomic
USB: ftdi_sio: Add more identifiers
xHCI: Cleanup isoc transfer ring when TD length mismatch found
usb: musb: omap2430: minor cleanups.
qcaux: add more Pantech UML190 and UML290 ports
Revert "drivers: usb: Fix dependency for USB_HWA_HCD"
usb: mv-otg - Fix build if CONFIG_USB is not set
USB: cdc-wdm: Avoid hanging on interface with no USB_CDC_DMM_TYPE
usb: add support for STA2X11 host driver
drivers: usb: Fix dependency for USB_HWA_HCD
kernel-doc: fix new warning in usb.h
USB: OHCI: fix new compiler warnings
usb: serial: kobil_sct: fix compile warning:
drivers/usb/host/ehci-fsl.c: add missing iounmap
USB: cdc-wdm: better allocate a buffer that is at least as big as we tell the USB core
USB: cdc-wdm: call wake_up_all to allow driver to shutdown on device removal
USB: cdc-wdm: use two mutexes to allow simultaneous read and write
USB: cdc-wdm: updating desc->length must be protected by spin_lock
USB: usbsevseg: fix max length
...
1) Setting link attributes can modify the size of the attributes that
would be reported on a subsequent getlink netlink operation,
therefore min_ifinfo_dump_size needs to be adjusted. From Stefan
Gula.
2) Resegmentation of TSO frames while trimming can violate invariants
expected by callers, namely that the number of segments can only stay
the same or decrease, never increase. If MSS changes, however, we
can trim data but then end up with more segments. Fix this by only
segmenting to the MSS already recorded in the SKB. That's the
simplest fix for now and if we want to get more fancy in the future
that's a more involved change.
This probably explains some retransmit counter inaccuracies.
From Neal Cardwell.
3) Fix too-many-wakeups in POLL with AF_UNIX sockets, from Eric Dumazet.
4) Fix CAIF crashes wrt. namespace handling. From Eric Dumazet and
Eric W. Biederman.
5) TCP port selection fixes from Flavio Leitner.
6) More socket memory cgroup build fixes in certain randonfig
situations. From Glauber Costa.
7) Fix TCP memory sysctl regression reported by Ingo Molnar, also from
Glauber Costa.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
af_unix: fix EPOLLET regression for stream sockets
tcp: fix tcp_trim_head() to adjust segment count with skb MSS
net/tcp: Fix tcp memory limits initialization when !CONFIG_SYSCTL
net caif: Register properly as a pernet subsystem.
netns: Fail conspicously if someone uses net_generic at an inappropriate time.
net: explicitly add jump_label.h header to sock.h
net: RTNETLINK adjusting values of min_ifinfo_dump_size
ipv6: Fix ip_gre lockless xmits.
xen-netfront: correct MAX_TX_TARGET calculation.
netns: fix net_alloc_generic()
tcp: bind() optimize port allocation
tcp: bind() fix autoselection to share ports
l2tp: l2tp_ip - fix possible oops on packet receive
iwlwifi: fix PCI-E transport "inta" race
mac80211: set bss_conf.idle when vif is connected
mac80211: update oper_channel on ibss join
which shook out in -rc. The bindings were overly enthusiatic when
deciding to set a voltage on a regulator and would try to set zero volts
on an unconfigured regulator which isn't supported.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nREk
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
This fixes an integration issue with the regulator device tree bindings
which shook out in -rc. The bindings were overly enthusiatic when
deciding to set a voltage on a regulator and would try to set zero volts
on an unconfigured regulator which isn't supported.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Set apply_uV only when min and max voltages are defined
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] dasd: revalidate server for new pathgroup
[S390] dasd: revert LCU optimization
[S390] cleanup entry point definition
Commits 3fe4bae884 and
079c985e7a broke MTD suspend in 2 ways:
1. When the '->suspend' method is not present, we return -EOPNOTSUPP, but
the callers of 'mtd_suspend()' expects 0 instead.
2. Checking of the 'mtd' parameter against NULL has been incorrectly removed
in 'mtd_cls_suspend()'.
This patch fixes the breakages. This has been found, analyzed, reported
and tested by Rafael J. Wysocki <rjw@sisk.pl>.
Note, this patch is not needed in the stable tree because it causes a
regression introduced during the v3.3 merge window.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Error handling in msm_iommu_unmap() is broken. On some error
conditions retval is set to a non-zero value which causes
the function to return 'len' at the end. This hides the
error from the user. Zero should be returned in those error
cases.
Cc: David Brown <davidb@codeaurora.org>
Cc: Stepan Moskovchenko <stepanm@codeaurora.org>
Cc: stable@vger.kernel.org # >= 3.1
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: David Brown <davidb@codeaurora.org>
The assignment of handle in vmw_framebuffer_create_handle doesn't actually do anything useful and is incorrectly assigning an integer value to a pointer argument. It appears that this is a typo and should be dereferencing handle rather than assigning to it directly. This fixes a bug where an undefined handle value is potentially returned to user-space.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Jakob Bornecrantz<jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Properly set the parent device of i2c buses before registering them so
that they will show at the right place in the device tree (rather than
in /sys/devices directly.)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In particular, I found I was hitting the max-file limit in the VFS,
and the EFILE was being magically transformed into ENOMEM. Confusion
reigns.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 87499ffdcb.
Where is that paper bag ... ah here.
I've failed to take an odd interaction between my other cleanups and
this reclaim_buffers patch into account and also failed to properly
test it. Looks like there are more dragons and hidden trapdoors in the
drm release path than actual lines of code.
Until I get a clue, let's just revert this.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This otg driver depends on marvell EHCI driver, so add the dependence.
It can fix the following build error on i386:
ERROR: "usb_remove_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
ERROR: "usb_add_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ab943a2e12 (USB: gadget: gadget zero uses new suspend/resume hooks)
introduced a copy-paste error where f_loopback.c writes to a variable
declared in f_sourcesink.c. This prevents one from creating gadgets
that only have a loopback function.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
NCT6776F only supports pwm mode for pwm2 and pwm3. Return error if an attempt
is made to set those pwm channels to DC mode.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
When no platform data was supplied, returned error code was 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 2.6.32+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
It contains the removal of the sysdev code, now that all users of it are
gone, as well as some sysfs bugfixes that have been reported by users.
There are also some documentation updates here as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk8jKW4ACgkQMUfUDdst+ynAUwCfVWwHJxpb4DSSMVZhGOnHMQrL
ZjIAn00gPeSs5u8y1nPvFrFikbon4FDs
=bzVy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3-rc1-bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Here are some patches for the 3.3-rc1 tree.
It contains the removal of the sysdev code, now that all users of it are
gone, as well as some sysfs bugfixes that have been reported by users.
There are also some documentation updates here as well.
* tag 'driver-core-3.3-rc1-bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Complain bitterly about attempts to remove files from nonexistent directories.
stable: update documentation to ask for kernel version
base/core.c:fix typo in comment in function device_add
Documentation: devres: add allocation functions to list of supported calls
Documentation update for the driver model core
kernel-doc: fix new warnings in driver-core
kernel-doc: fix new warnings in debugfs
kernel-doc: fix new warnings in device.h
driver core: remove drivers/base/sys.c and include/linux/sysdev.h
* 'stable/for-linus-fixes-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/granttable: Disable grant v2 for HVM domains.
x86: xen: size struct xen_spinlock to always fit in arch_spinlock_t
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm: (31 commits)
ARM: 7304/1: ioremap: fix boundary check when reusing static mapping
ARM: 7301/1: Rename the T() macro to TUSER() to avoid namespace conflicts
ARM: 7299/1: ftrace: clear zero bit in reported IPs for Thumb-2
ARM: 7298/1: realview: fix mapping of MPCore private memory region
PCMCIA: fix sa1111 oops on remove
ARM: 7288/1: mach-sa1100: add missing module_init() call
ARM: 7297/1: smp_twd: make sure timer is stopped before registering it
ARM: 7296/1: proc-v7.S: remove HARVARD_CACHE preprocessor guards
ARM: 7295/1: cortex-a7: move proc_info out of !CONFIG_ARM_LPAE block
ARM: 7293/1: logical_cpu_map: decouple CPU mapping from SMP
ARM: 7291/1: cache: assume 64-byte L1 cachelines for ARMv7 CPUs
ARM: 7290/1: vmlinux.lds.S: align the exception fixup table to a 4-byte boundary
ARM: 7289/1: vmlinux.lds.S: do not hardcode cacheline size as 32 bytes
MFD: ucb1x00-ts: fix resume failure
MFD: ucb1x00-core: fix gpiolib direction_output handling
MFD: ucb1x00-core: fix missing restore of io output data on resume
MFD: mcp-core: fix mcp_priv() to be more type safe
MFD: mcp-core: fix complaints from the genirq layer
Revert "ARM: sa11x0: Implement autoloading of codec and codec pdata for mcp bus."
Revert "ARM: sa1100: Refactor mcp-sa11x0 to use platform resources."
...
Fix up conflict due to arch/arm/mach-mx5/Kconfig having been merged into
mach-imx5 (commit 784a90c0a7d8: "ARM i.MX: Merge i.MX5 support into
mach-imx"), but the ARM_L1_CACHE_SHIFT_6 entry was moved to be driven by
the CPU_V7 logic from it in the old location in rmk's branch (commit
a092f2b15399: "ARM: 7291/1: cache: assume 64-byte L1 cachelines for
ARMv7 CPUs").
AT91 needed reset fixes which resulted in some minor code refactoring,
it also adds a feature-removal for one of their platforms for 3.4.
The USB patches have been acked by Greg K-H.
i.MX and ux500 both have some minor fixes, nothing controversial.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nS4F
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
arm-soc fixes for 3.3-rc:
AT91 needed reset fixes which resulted in some minor code refactoring,
it also adds a feature-removal for one of their platforms for 3.4.
The USB patches have been acked by Greg K-H.
i.MX and ux500 both have some minor fixes, nothing controversial.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-imx/mach-mx53_ard.c: add missing iounmap
ARM: imx: iomux-v1.h: Fix build error due to __init annotation
ARM: at91: Fix at91sam9g45 and at91cap9 reset
ARM: at91: make rstc soc independent
ARM: at91: introduce AT91_SAM9_ALT_RESET to select the at91sam9 alternative reset
ARM: at91: merge at91cap9_ddrsdr.h in at91sam9_ddrsdr.h
ARM: at91: fix cap9 ddrsdr register
ARM/USB: at91/ohci-at91: rename vbus_pin_inverted to vbus_pin_active_low
USB: at91: fix clk_get error handling
ARM: at91: removal of CAP9 SoC family
ARM: at91: fix at91rm9200 soc subtype handling
mach-ux500: no MMC_CAP_SD_HIGHSPEED on Snowball
mach-ux500: enable ARM errata 764369
mach-ux500: do not override outer.inv_all
mach-ux500: musb: now musb is always in OTG mode
ARM: imx6: add missing twd_clk for imx6q clock
An error was existing in the saving of CONTRAST_CTR register
across suspend/resume.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The goto on the line before means the return is unreachable. The goto
also returns -ENODEV so no changes are needed there.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix a compiler errors introduced in:
commit ddd3d90543
Author: Timur Tabi <timur@freescale.com>
drivers/video: fsl-diu-fb: merge all allocated data into one block
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Use virtio_mb() to make sure the available index to be exposed before
checking the the avail event. Otherwise we may get stale value of
avail event in guest and never kick the host after.
Note: this fixes a bug introduced by ee7cd8981e.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Note: this fixes a bug introduced recently in
7b21e34fd1.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix fast memory registration opcode in local invalidate completion.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Donald Wood <Donald.E.Wood@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Zero high order word of fast memory registration (FMR) length field.
FMR length field is 32 bits, so high word should always be zero.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Donald Wood <Donald.E.Wood@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
After reporting a new connection request to user space, the rdma_ucm
will discard subsequent events until the user has associated a user
space idenfier with the kernel cm_id. This is needed to avoid
reporting a reject/disconnect event to the user for a request that
they may not have processed.
The user space identifier is set once the user tries to accept the
connection request. However, the following race exists in ucma_accept():
ctx->uid = cmd.uid;
<events may be reported now>
ret = rdma_accept(ctx->cm_id, ...);
Once ctx->uid has been set, new events may be reported to the user.
While the above mentioned race is avoided, there is an issue that the
user _may_ receive a reject/disconnect event if rdma_accept() fails,
depending on when the event is processed. To simplify the use of
rdma_accept(), discard all events unless rdma_accept() succeeds.
This problem was discovered based on questions from Roland Dreier
<roland@purestorage.com>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 8d4548f2b ("IB/qib: Default some module parameters optimally")
introduced an issue with older root complexes. They cannot handle the
pcie_caps of 0x51 (MaxReadReq 4096, MaxPayload=256).
A typical diagnostic in this situation reported by syslog contains
the text:
[PCIe Poisoned TLP][Send DMA memory read]
Restore the module paramter default to zero with will avoid any
changes in the root complex.
Reviewed-by: Mark Debbage <mark.debbage@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
alloc_dummy_hdrq() is called with locks held and thus should not use
GFP_KERNEL.
The semantic patch that makes this report is available in
scripts/coccinelle/locks/call_kern.cocci.
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make sure all exit paths from this function unlock everything.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set a reject flag, when sending MPA reject message to inform the peer
that the application has rejected the connection.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
"dentry" is a valid pointer. "*dentry" was intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We have just been investigating kernel panics related to
cq->ibcq.event_handler() completion calls. The problem is that
ib_destroy_qp() fails with -EBUSY.
Further investigation revealed qp->usecnt is not initialized. This
counter was introduced in linux-3.2 by commit 0e0ec7e063
("RDMA/core: Export ib_open_qp() to share XRC TGT QPs") but it only
gets initialized for IB_QPT_XRC_TGT, but it is checked in
ib_destroy_qp() for any QP type.
Fix this by initializing qp->usecnt for every QP we create.
Signed-off-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Sven Breuner <sven.breuner@itwm.fraunhofer.de>
[ Initialize qp->usecnt in uverbs too. - Sean ]
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
gma500: Fix suspend/resume functions
drm/exynos: fixed pm feature for fimd module.
MAINTAINERS: added maintainer entry for Exynos DRM Driver.
drm/exynos: fixed build dependency for DRM_EXYNOS_FIMD
drm/exynos: fix build dependency for DRM_EXYNOS_HDMI
drm/exynos: use release_mem_region instead of release_resource
agp: fix scratch page cleanup
drm/i915: fixup forcewake spinlock fallout in drpc debugfs function
drm/i915: debugfs: show semaphore registers also on gen7
drm/i915: allow userspace forcewake references also on gen7
drm/i915: Re-enable gen7 RC6 and GPU turbo after resume.
drm/i915: Correct debugfs printout for RC1e.
Revert "drm/i915: Work around gen7 BLT ring synchronization issues."
drm/i915: rip out the HWSTAM missed irq workaround
drm/i915: paper over missed irq issues with force wake voodoo
drm/i915: Hold gt_lock across forcewake register reads
drm/i915: Hold gt_lock during reset
drm/i915: Move reset forcewake processing to gen6_do_reset
drm/i915: protect force_wake_(get|put) with the gt_lock
drm/i915: convert force_wake_get to func pointer in the gpu reset code
...
Both the suspend and resume functions incorrectly set psbfb =
to_psb_fb(NULL) outside of the loop over all of the framebuffers. Fix
this by moving the assignment of psbfb inside the loop and removing the
initialisation of fb.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds the TCO Watchdog DeviceIDs for the Intel Lynx Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Let the watchdog core to check the valid value range of min_timeout/max_timeout.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Correct typo "unexpectdly" to "unexpectedly" in pnx4008_wdt.c
and stmp3xxx_wdt.c
Signed-off-by: Masanari Iida<standby24x7@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
While receiving WDIOS_DISABLECARD option for WDIOC_SETOPTIONS command,
call wafwdt_stop() to disable watchdog.
Call wafwdt_start() while receiving WDIOS_ENABLECARD option.
Current code has reverse behavior.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
While receiving WDIOS_DISABLECARD option for WDIOC_SETOPTIONS command,
call wm8350_wdt_stop() to disable watchdog.
Call wm8350_wdt_start() while receiving WDIOS_ENABLECARD option.
Current code has reverse behavior.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is only used in this driver, so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is only used in this driver, so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Marc Vertes <marc.vertes@sigfox.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently the watchdog driver calls the pm_runtime_enable and never
the disable. This may cause a warning when pm_runtime_enable
checks for the count match.
Also fixes the error
/build/watchdog # insmod omap_wdt.ko
[ 44.999389] omap_wdt omap_wdt: Unbalanced pm_runtime_enable!
[ 45.011047] OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
/build/watchdog #
Attempting to fix the same by calling pm_runtime_disable.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reimplement a call to devm_request_mem_region followed by a call to ioremap
or ioremap_nocache by a call to devm_request_and_ioremap.
The semantic patch that makes this transformation is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\))) {
- ...
- return ...;
-}
... when != res->start
(
-devm_ioremap(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
|
-devm_ioremap_nocache(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
)
... when any
when != res->start
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reimplement a call to devm_request_mem_region followed by a call to ioremap
or ioremap_nocache by a call to devm_request_and_ioremap.
The variable res_size is then no longer needed.
The semantic patch that makes this transformation is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\))) {
- ...
- return ...;
-}
... when != res->start
(
-devm_ioremap(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
|
-devm_ioremap_nocache(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
)
... when any
when != res->start
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
this patch separates fimd specific power on/off function from pm function
and the pm interfaces will call that function for power on or off.
and also removes unnecessary codes of resume function.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
FB based FIMD and DRM based FIMD drivers use same hardware
so with this patch, only one of them would be selected.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Jesper Juhl