* Change the scan interval from 100ms to 50ms. This stops the key
repeat from triggering on double letter presses.
* Remove unneeded stale hinge code from corgikbd
* Change unneeded corgi GPIO pins to inputs when suspended
* Add support for the headphone jack switch for both corgi and spitz
(as switch SW_2)
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not assume that pnp_register_driver() returns the number of
devices claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not assume that pnp_register_driver() returns the number of
devices claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The current pcspkr code combines the device and driver registration.
This patch splits these, putting the device registration in the arch
specific code.
PowerPC and MIPS only have the pcspkr present sometimes.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow disabling atkbd driver if CONFIG_EMBEDDED is enabled. Previously
it was impossible to disable atkbd on X86_PC.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not activate softrepeat by default on dumb keyboards as it clashes
with their own hardware repeat (for example Dell DRAC3). Softrepeat
can still be activated manually via module parameter or sysfs.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix bat_xl and err_xl logic causing atkbd to complain about 'unknown
key 0x7f'. Noted by Ben LaHaise.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Automatic resynchronization in psmouse driver causes problems on some
hardware so disable it by default for now. People with KVM switches
that require resync can still enable it via module parameter or sysfs
attribute.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Serio and gameport cores do not depend on other drivers and are
used by code living outside of drivers/input/{gameport|serio}.
Registering them at subsystem level guarantees that they are
fully initialized before anyone tries to use them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Amijoy conversion was done by Arjan van de Ven.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
98kbd{,-io} and 98spkr all went out with PC98 subarch. Remove stale Makefile
entries that remained.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This updates the ads7846 touchscreen driver:
- to allow faster clocking (this driver doesn't push sample rates);
- bugfixes the conversion of spi_transfer to lists;
- some dma-unsafe command buffers are fixed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Logitech mouse type 99 (Premium Optical Wheel Mouse, model M-BT58,
plain 3 buttons + wheel) to cure the following message: logips2pp: Detected
unknown logitech mouse model 99
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Recent conversion to wait_event_interruptible_timeout() caused
USB detection routine erroneously report timeouts for perfectly
working devices.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently, "while true; do cat </dev/null >/dev/input/mice; done" causes
an OOM in a short amount of time. Funny that nobody noticed, it actually
is very easy to trigger just by switching between VT1 and VT7...
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a driver for beeper found in LinkSys NSLU2 boxes. It should work
on any ixp4xx based platform.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There's no need to have request_irq followed by set_irq_type.
Just use request_irq with the appropriate SA_TRIGGER flags.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most of the reasons for keeping these separate before was due to hp690
discontig, and since we have a workaround for that now (abusing some shadow
space so everything is magically contiguous), there's no reason to keep the
targets separate.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes the SPI core and its users access transfers in the SPI message
structure as linked list not as an array, as discussed on LKML.
From: David Brownell <dbrownell@users.sourceforge.net>
Updates including doc, bugfixes to the list code, add
spi_message_add_tail(). Plus, initialize things _before_ grabbing the
locks in some cases (in case it grows more expensive). This also merges
some bitbang updates of mine that didn't yet make it into the mm tree.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the ads7864 driver to use the new "spi_driver" struct, and
includes some minor unrelated cleanup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the ADS7846 touchscreen sensor, derived from
the corgi_ts and omap_ts drivers. Key differences from those two:
- Uses the new SPI framework (minimalist version)
- <linux/spi/ads7846.h> abstracts board-specific touchscreen info
- Sysfs attributes for the temperature and voltage sensors
- Uses fewer ARM-specific IRQ primitives
The temperature and voltage sensors show up in sysfs like this:
$ pwd
/sys/devices/platform/omap-uwire/spi2.0
$ ls
bus@ input:event0@ power/ temp1 vbatt
driver@ modalias temp0 vaux
$ cat modalias
ads7846
$ cat temp0
991
$ cat temp1
1177
$
So far only basic testing has been done. There's a fair amount of hardware
that uses this sensor, and which also runs Linux, which should eventually
be able to use this driver.
One portability note may be of special interest. It turns out that not all
SPI controllers are happy issuing requests that do things like "write 8 bit
command, read 12 bit response". Most of them seem happy to handle various
word sizes, so the issue isn't "12 bit response" but rather "different rx
and tx write sizes", despite that being a common MicroWire convention. So
this version of the driver no longer reads 12 bit native-endian words; it
reads 16-bit big-endian responses, then byteswaps them and shifts the
results to discard the noise.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in amigahw.h custom renamed to amiga_custom, in drivers with few instances the
same replacement, in the rest - #define custom amiga_custom in driver itself
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The API and code have been through various bits of initial review by
serial driver people but they definitely need to live somewhere for a
while so the unconverted drivers can get knocked into shape, existing
drivers that have been updated can be better tuned and bugs whacked out.
This replaces the tty flip buffers with kmalloc objects in rings. In the
normal situation for an IRQ driven serial port at typical speeds the
behaviour is pretty much the same, two buffers end up allocated and the
kernel cycles between them as before.
When there are delays or at high speed we now behave far better as the
buffer pool can grow a bit rather than lose characters. This also means
that we can operate at higher speeds reliably.
For drivers that receive characters in blocks (DMA based, USB and
especially virtualisation) the layer allows a lot of driver specific
code that works around the tty layer with private secondary queues to be
removed. The IBM folks need this sort of layer, the smart serial port
people do, the virtualisers do (because a virtualised tty typically
operates at infinite speed rather than emulating 9600 baud).
Finally many drivers had invalid and unsafe attempts to avoid buffer
overflows by directly invoking tty methods extracted out of the innards
of work queue structs. These are no longer needed and all go away. That
fixes various random hangs with serial ports on overflow.
The other change in here is to optimise the receive_room path that is
used by some callers. It turns out that only one ldisc uses receive room
except asa constant and it updates it far far less than the value is
read. We thus make it a variable not a function call.
I expect the code to contain bugs due to the size alone but I'll be
watching and squashing them and feeding out new patches as it goes.
Because the buffers now dynamically expand you should only run out of
buffering when the kernel runs out of memory for real. That means a lot of
the horrible hacks high performance drivers used to do just aren't needed any
more.
Description:
tty_insert_flip_char is an old API and continues to work as before, as does
tty_flip_buffer_push() [this is why many drivers dont need modification]. It
does now also return the number of chars inserted
There are also
tty_buffer_request_room(tty, len)
which asks for a buffer block of the length requested and returns the space
found. This improves efficiency with hardware that knows how much to
transfer.
and tty_insert_flip_string_flags(tty, str, flags, len)
to insert a string of characters and flags
For a smart interface the usual code is
len = tty_request_buffer_room(tty, amount_hardware_says);
tty_insert_flip_string(tty, buffer_from_card, len);
More description!
At the moment tty buffers are attached directly to the tty. This is causing a
lot of the problems related to tty layer locking, also problems at high speed
and also with bursty data (such as occurs in virtualised environments)
I'm working on ripping out the flip buffers and replacing them with a pool of
dynamically allocated buffers. This allows both for old style "byte I/O"
devices and also helps virtualisation and smart devices where large blocks of
data suddenely materialise and need storing.
So far so good. Lots of drivers reference tty->flip.*. Several of them also
call directly and unsafely into function pointers it provides. This will all
break. Most drivers can use tty_insert_flip_char which can be kept as an API
but others need more.
At the moment I've added the following interfaces, if people think more will
be needed now is a good time to say
int tty_buffer_request_room(tty, size)
Try and ensure at least size bytes are available, returns actual room (may be
zero). At the moment it just uses the flipbuf space but that will change.
Repeated calls without characters being added are not cumulative. (ie if you
call it with 1, 1, 1, and then 4 you'll have four characters of space. The
other functions will also try and grow buffers in future but this will be a
more efficient way when you know block sizes.
int tty_insert_flip_char(tty, ch, flag)
As before insert a character if there is room. Now returns 1 for success, 0
for failure.
int tty_insert_flip_string(tty, str, len)
Insert a block of non error characters. Returns the number inserted.
int tty_prepare_flip_string(tty, strptr, len)
Adjust the buffer to allow len characters to be added. Returns a buffer
pointer in strptr and the length available. This allows for hardware that
needs to use functions like insl or mencpy_fromio.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These haven't worked in some time, and we've dropped support for the bus
from the SH tree until someone shows some interest in maintaining it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Avoid doing assignments to a live ->fops so it can be marked as 'const'.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
offset can never be < 0 because it has type size_t. The driver
currently oopses on insmod if BIOS does not support the interface,
instead of refusing to load.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Many ARM drivers do not need to include asm/irq.h - remove this
unnecessary include from some ARM drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call serio_reconnect() instead of serio_rescan() when detecting that
a new keyboard was plugged in. This should help KVM uses losing custom
keymap settings when switching between boxes.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Here's the patch for modalias support for input classes. It uses
comma-separated numbers, and doesn't describe all the potential keys (no
module currently cares, and that would make the strings huge). The
changes to input.h are to move the definitions needed by file2alias
outside __KERNEL__. I chose not to move those definitions to
mod_devicetable.h, because there are so many that it might break compile
of something else in the kernel.
The rest is fairly straightforward.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
CC: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It makes zero sense to have hotplug, but not the netlink
events enabled today. Remove this option and merge the
kobject_uevent.h header into the kobject.h header file.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a typo introduced by conversion to dynamic input_dev
allocation.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Christophe Zimmerman, this explains the slow mouse movement
with 2.6.x kernels.
And checking the 2.4.x drivers/sbus/char/sunmouse.c driver shows we
always used a 5-byte protocol with Sun mice in the past. I have no
idea how the 3-byte thing got into the 2.6.x driver, but it's surely
wrong.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding would work.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Introduce a Kconfig symbol SPARC that is defined on both the sparc and
sparc64 architectures.
This symbol makes some dependencies more readable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This DMI data was found in Fujitsu LifeBook B142 (Product S/N
FPC01003B, italian keyboard); re: bugzilla #5335
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It looks like quite a few mice out there treat PSMOUSE_RESET_DIS
as a powerdown request and turn off the light rendering the mouse
unusable.
Vojtech recommended to switch from PSMOUSE_RESET_DIS to full reset,
however we don't want to do that everywhere as full reset is pretty
slow. Instead we only use it before probing for "generic" protocols,
such as IntelliMouse and Explorer, to make sure that the mouse will
be woken up if it went to sleep as a result of PSMOUSE_RESET_DIS
issued earlier.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Without this patch Forward and Backward buttons on the touchpad do not
generate any events.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Compat and normal code mirror each other and are hard to maintain.
When EV_SW was added compat_ioctl case was missed. Here is my attempt
at consolidating the code.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
kseriod and kgameportd used to process all pending events before
checking for freeze condition. This may cause swsusp to time out
while stopping tasks when resuming. Switch to process events one
by one to check freeze status more often.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If thread that submitted FF request gets interrupted somehow it
will release request structure and ioctl handler will work with
freed memory. TO prevent that from happening switch to using
wait_for_completion instead of wait_for_completion_interruptible.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Try to save battery power by disabling wifi and bluetooth on suspend.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also fix a potential issue with some notebooks:
The current code assumes the response to bios_wifi_get_default_setting is
either 1 (disabled) or 3 (enabled), or wifi isn't supported. The BIOS
response appears to be a bit field w/ 0x1 indicating hardware presence, 0x2
indicating actiation status, and the other 6 bits being unknown/reserved --
with the patch, these 6 bits are ignored.
Signed-off-by: Bernhard Rosenkraenzer <bero@arklinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On x86_64:
{standard input}:233: Error: suffix or operands invalid for `push'
{standard input}:233: Error: suffix or operands invalid for `pop'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A driver for laptop buttons using an x86 BIOS interface that is
apparently used on quite a few laptops and seems to be originating
from Wistron.
This driver currently "knows" only about Fujitsu-Siemens Amilo Pro V2000
(i.e. it can detect the laptop using DMI and it contains the
keycode->key meaning mapping for this laptop) and Xeron SonicPro X 155G
(probably can't be reliably autodetected, requires a module parameter),
adding other laptops should be easy.
In addition to reporting button presses to the input layer the driver
also allows enabling/disabling the embedded wireless NIC (using the
"Wifi" button); this is done using the same BIOS interface, so it seems
only logical to keep the implementation together. Any flexibility
possibly gained by allowing users to remap the function of the "Wifi"
button is IMHO not worth it when weighted against the necessity to run
an user-space daemon to convert button presses to wifi state changes.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Changing led state is pretty slow operation; when there are multiple
requests coming at a high rate they may interfere with normal typing.
Try optimize (skip) changing hardware state when multiple requests
are coming back-to-back.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the remaining misc drivers/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in misc files in
drivers/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: "Antonino A. Daplas" <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Hide debugging code into #ifdef, which allows to simplify
the large switch statement
* Update macros to not reference variables not given as
arguments
Signed-off-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not register statically allocated input devices to prevent
OOPS when attaching input interfaces since it requires class
device to be properly initialized.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PC is left-over cruft after the introduction of CONFIG_X86_PC with
the subarch split. Remove it, and fixup the remaining users to depend on
CONFIG_X86_PC instead.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add CONFIG_X86_32 for i386. This allows selecting options that only apply
to 32-bit systems.
(X86 && !X86_64) becomes X86_32
(X86 || X86_64) becomes X86
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Input: remove custom-made hotplug handler
Now that all input devices are registered with sysfs we can remove
old custom-made hotplug handler and crate a standard one.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This creates symlinks in /sys/class/input/ to the nested class devices
to help userspace cope with the nesting.
Unfortunatly udev still needs to be updated as it can't handle symlinks
properly here :(
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Input: show sysfs path in /proc/bus/input/devices
Show that sysfs and phys path are different objects.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous patch adding the ability to nest struct class_device
changed the paramaters to the call class_device_create(). This patch
fixes up all in-kernel users of the function.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update drivers to new input layer changes.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Reorder code in gscps2_interrupt() and only enable ports when opened.
This fixes issues with hangs booting an SMP kernel on my C360.
Previously serio_interrupt() could be called before the lock in
struct serio was initialised.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make /sys/bus/parisc/drivers look better by cleaning up parisc_driver
names.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Only signal completion after marking request slot as free, otherwise other
processor can free request structure before we finish using it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes depenencies of collie keyboard.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Correct the right shift key entry in the spitz keyboard driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The wwitch bitmap was added to input_device_id structure and we should
check it when matching handlers and input devices.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a input driver for the keyboard found on the Zaurus Cxx00 series (Spitz,
Akita, Borzoi). Its based on corgikbd but there are enough subtle differences
to justify a separate driver.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
Touchscreen driver. Use the new functions in corgi_lcd.c via sharpsl.h for
hsync handling and pass the IRQ as a platform device resource. Move a
function prototype into the w100fb header file where it belongs.
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The corgi keyboard has need of a switch event type with slightly type to the
input system as recommended by the input maintainer.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the platform specific Sharp SL-C7x0 LCD code from the
w100fb driver into a more appropriate place and updates the Corgi code to
match the new w100fb driver.
It also updates the corgi touchscreen code to match the new simplified
interface available from w100fb.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Corgi Touchscreen bugfix. If the PMU isn't running, the register needs to
be set to a sane value rather than reusing some random value.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up some Corgi Touchscreen logic and merge the repeat calls to
w100fb_blanking() in anticipation of the w100fb patch.
Fix a pm_message_t reference.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Corgi Touchscreen driver uses the PMU as an accurate timing source which
conflicts with its usage for performance monitoring. This patch allows it to
be shared with other users such as oprofile.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The input system handles key state tracking so there's no need for the driver
to do so as well. Also tidy up some comment formatting and remove a now
unneeded function.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some power management code to the corgi keyboard driver so that only one
power event gets reported within any reasonable time frame and the driver
doesn't enter an infinte loop due to key repeat.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a couple of compile errors in the corgi keyboard driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the compat mode kludgeology in envdev to cover MIPS as well.
Or why we should need something like is_compat_task() ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The timeout while() loops in iforce-packets.c lack a
set_current_state(TASK_INTERRUPTIBLE); call. The right solution is
to replace them with wait_event_interruptible_timeout().
Reported-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Extend bat_xl handling to do err_xl handling, so that
keyboards using 0x7f scancode for regular keys can work.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When dev->keycodesize == sizeof(int) the old code produces
incorrect result.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Rearrange attribute code to use generic show and set handlers
instead of replicating them for every attribute; switch to
using attribute_group instead of creating all attributes
manually. All this saves about 4K.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Need to use list_for_entry_safe(), as we're removing items during the
traversal. list_for_each_entry() uses the first ptr also as an iterator, if
you kfree() it slab takes it, might poison it and then you try to use it to
iterate to the next object in list.
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Synaptics driver used child->type to select either 3-byte or 4-byte
packet size for the pass-through port; this gives wrong results for
the newer protocols. Change the check to use child->pktsize instead.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When changing key mappings we need to make sure that the new
keycode value can be stored in dev->keycodesize bytes.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently i8042_command() negates data coming from the AUX port
of keyboard controller; this is not a very reliable indicator.
Change i8042_command() to fail if response to I8042_CMD_AUX_LOOP
is not coming from AUX channel and get rid of negation.
Based on patch by Vojtech Pavlik.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are wheel mice that respond to Logitech probes and report
that they have only 2 buttons (such as e-Aser mouse) and this
stops the wheel from being used as a middle button. Change the
driver to always report BTN_MIDDLE capability if a wheel is
present.
Also, never reset BTN_RIGHT capability in logips2pp code - there
are no Logitech mice that have only one button and if some other
mice happen to respond to Logitech's query we could do the wrong
thing.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Replace the MSECS() macro with the jiffies_to_msecs() function provided
in jiffies.h
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The condition in alps_init() was also inverted and the driver
was enabling tapping mode only if it was already enabled.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver would not reset pass-through mode when performing
resume of a DualPoint touchpad causing it to stop working
until next reboot.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
git did actually warn me about the fact that I hadn't actually done an
"update-cache" on these two files, but the warning was at the bottom of
a list of all the files that _did_ change in the merge, so I never
noticed. My bad.
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.12-rc6-mm1 has a few remaining synchronize_kernel()s, some (but not
all) in comments. This patch changes these synchronize_kernel() calls (and
comments) to synchronize_rcu() or synchronize_sched() as follows:
- arch/x86_64/kernel/mce.c mce_read(): change to synchronize_sched() to
handle races with machine-check exceptions (synchronize_rcu() would not cut
it given RCU implementations intended for hardcore realtime use.
- drivers/input/serio/i8042.c i8042_stop(): change to synchronize_sched() to
handle races with i8042_interrupt() interrupt handler. Again,
synchronize_rcu() would not cut it given RCU implementations intended for
hardcore realtime use.
- include/*/kdebug.h comments: change to synchronize_sched() to handle races
with NMIs. As before, synchronize_rcu() would not cut it...
- include/linux/list.h comment: change to synchronize_rcu(), since this
comment is for list_del_rcu().
- security/keys/key.c unregister_key_type(): change to synchronize_rcu(),
since this is interacting with RCU read side.
- security/keys/process_keys.c install_session_keyring(): change to
synchronize_rcu(), since this is interacting with RCU read side.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements a number of smp_processor_id() cleanup ideas that
Arjan van de Ven and I came up with.
The previous __smp_processor_id/_smp_processor_id/smp_processor_id API
spaghetti was hard to follow both on the implementational and on the
usage side.
Some of the complexity arose from picking wrong names, some of the
complexity comes from the fact that not all architectures defined
__smp_processor_id.
In the new code, there are two externally visible symbols:
- smp_processor_id(): debug variant.
- raw_smp_processor_id(): nondebug variant. Replaces all existing
uses of _smp_processor_id() and __smp_processor_id(). Defined
by every SMP architecture in include/asm-*/smp.h.
There is one new internal symbol, dependent on DEBUG_PREEMPT:
- debug_smp_processor_id(): internal debug variant, mapped to
smp_processor_id().
Also, i moved debug_smp_processor_id() from lib/kernel_lock.c into a new
lib/smp_processor_id.c file. All related comments got updated and/or
clarified.
I have build/boot tested the following 8 .config combinations on x86:
{SMP,UP} x {PREEMPT,!PREEMPT} x {DEBUG_PREEMPT,!DEBUG_PREEMPT}
I have also build/boot tested x64 on UP/PREEMPT/DEBUG_PREEMPT. (Other
architectures are untested, but should work just fine.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like logic for enabling hardware tapping in ALPS driver was
inverted and we enable it only if it was already enabled by BIOS or
firmware.
I have a confirmation from one user that the patch below fixes the problem
for him and it might be beneficial if we could get it into 2.6.12.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch disables the scroll feature on AT keyboards by default, because
it causes the numbers of mouse devices to shift, breaking user setups.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
given number of bytes from device. Change ps2_command to
allow using 0 as command ID and actually pass it to the
device instead of working as a drain.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
operations do not iterfere with each other.
Also make sure that serio core takes serio->drv_sem
not only for connect/disconnect but for reconnect
too.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
entry->proc_fops is a pointer to struct file_operations. When we
call create_proc_entry(...), it pointis to proc_file_operations,
deep in fs/proc/generic.c. By adding a 'poll' member to this struct
we effectively force the 'poll' member on every file in /proc,
which is wrong (they all fail select(...) calls).
This patch changes a copy of entry->proc_fops and reassigns it rather
than changing the original member.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
uinput_alloc_device() is supposed to return the number of bytes read,
the value is returned to uinput_write() and from there to userspace. If
EV_ABS is set then it returns the value from uinput_validate_absbits()
instead, which is zero when everything is ok instead of the count.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Acked-by: Aristeu Rozanski <aris@cathedrallabs.org>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
I have an Ahtec laptop with a ALPS GlidePoint device, with 4 buttons.
With Linux hernel 2.6.12rc4 and rc5 I'm unable to use the vertical
scroll buttons (BACK and FORWARD).
BACK gets detected as BTN_MIDDLE and FORWARD is undetected.
I've modified the drivers/input/mouse/alps.c from 2.6.12rc5 and now it
works fine!
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- do not try to set rate and resolution in init method, let
psmouse core do it for us. This also removes special quirks
from the core;
- do not disable mouse before doing full reset - meaningless;
- some formatting and whitespace cleanups.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
serialize open and close calls and ensure that device's
open and close methods are only called when first user
opens it or last user closes it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
as function keys instead of special keys.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
I've tested it with a Logitech WingMan Rumblepad on an x86-64
machine, and on an ia32 machine to make sure I didn't break
anything.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not send empty events to gpm. (Keyboards are assumed to have scroll
wheel these days, that makes them part-mouse. That means typing on
keyboard generates empty mouse events).
From: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
because it interferes with ALPS touchpad detection and
causes horrible death on reboot. Since P10 does not have
external PS/2 ports MUX mode does not have any advantages
over legacy mode anyway.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
mapped twice, resulting in it being the last (instead
of first) button on a joystick.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sends an incorrect ID and wasn't recognized.
Reported-by: Stefan Seyfried <seife@suse.de>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
when no i8042 controller (not PnP, not legacy) is present.
From: Kurt Garloff <garloff@suse.de>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
for i386, it's printed on many machines and usually is not
a cause for worry.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
This patch adds dummy gameport_register_port, gameport_unregister_port
and gameport_set_phys functions to gameport.h for the case when a driver
can't use gameport.
This fixes the compilation of some OSS drivers with GAMEPORT=n without
the need to #if inside every single driver.
This patch also removes the non-working and now obsolete SOUND_GAMEPORT.
This patch is also an alternative solution for ALSA drivers with similar
problems (but #if's inside the drivers might have the advantage of
saving some more bytes of gameport is not available).
The only user-visible change is that for GAMEPORT=m the affected OSS
drivers are now allowed to be built statically (but they won't have
gameport support).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes two possible off by one errors found by the Coverity
checker (look at the period[i] and delay[j] in the two first unchanged
lines).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
serport - avoid calling serio_interrupt or serio_write_wakeup on unregistered
port. Also fix memory leak which could happen if serport was left unused by
moving serio allocation down to serport_ldisc_read.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ALPS needs to be reset for detection to work reliably when reconnecting.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
serio - do not attempt to immediately disconnect port if resume failed, let
kseriod take care of it. Otherwise we may attempt to unregister associated
input devices which will generate hotplug events which are not handled well
during swsusp.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes an array overflow found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Adrian Bunk