Based off 3bccd996 for ia64, convert powerpc to use the generic per-CPU
topology tracking, specifically:
initialize per cpu numa_node entry in start_secondary
remove the powerpc cpu_to_node()
define CONFIG_USE_PERCPU_NUMA_NODE_ID if NUMA
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we try to perform a kexec when the machine is in ST (Single-Threaded) mode
(ppc64_cpu --smt=off), the kexec operation doesn't succeed properly, and we
get the following messages during boot:
[ 0.089866] POWER8 performance monitor hardware support registered
[ 0.089985] power8-pmu: PMAO restore workaround active.
[ 5.095419] Processor 1 is stuck.
[ 10.097933] Processor 2 is stuck.
[ 15.100480] Processor 3 is stuck.
[ 20.102982] Processor 4 is stuck.
[ 25.105489] Processor 5 is stuck.
[ 30.108005] Processor 6 is stuck.
[ 35.110518] Processor 7 is stuck.
[ 40.113369] Processor 9 is stuck.
[ 45.115879] Processor 10 is stuck.
[ 50.118389] Processor 11 is stuck.
[ 55.120904] Processor 12 is stuck.
[ 60.123425] Processor 13 is stuck.
[ 65.125970] Processor 14 is stuck.
[ 70.128495] Processor 15 is stuck.
[ 75.131316] Processor 17 is stuck.
Note that only the sibling threads are stuck, while the primary threads (0, 8,
16 etc) boot just fine. Looking closer at the previous step of kexec, we observe
that kexec tries to wakeup (bring online) the sibling threads of all the cores,
before performing kexec:
[ 9464.131231] Starting new kernel
[ 9464.148507] kexec: Waking offline cpu 1.
[ 9464.148552] kexec: Waking offline cpu 2.
[ 9464.148600] kexec: Waking offline cpu 3.
[ 9464.148636] kexec: Waking offline cpu 4.
[ 9464.148671] kexec: Waking offline cpu 5.
[ 9464.148708] kexec: Waking offline cpu 6.
[ 9464.148743] kexec: Waking offline cpu 7.
[ 9464.148779] kexec: Waking offline cpu 9.
[ 9464.148815] kexec: Waking offline cpu 10.
[ 9464.148851] kexec: Waking offline cpu 11.
[ 9464.148887] kexec: Waking offline cpu 12.
[ 9464.148922] kexec: Waking offline cpu 13.
[ 9464.148958] kexec: Waking offline cpu 14.
[ 9464.148994] kexec: Waking offline cpu 15.
[ 9464.149030] kexec: Waking offline cpu 17.
Instrumenting this piece of code revealed that the cpu_up() operation actually
fails with -EBUSY. Thus, only the primary threads of all the cores are online
during kexec, and hence this is a sure-shot receipe for disaster, as explained
in commit e8e5c2155b (powerpc/kexec: Fix orphaned offline CPUs across kexec),
as well as in the comment above wake_offline_cpus().
It turns out that cpu_up() was returning -EBUSY because the variable
'cpu_hotplug_disabled' was set to 1; and this disabling of CPU hotplug was done
by migrate_to_reboot_cpu() inside kernel_kexec().
Now, migrate_to_reboot_cpu() was originally written with the assumption that
any further code will not need to perform CPU hotplug, since we are anyway in
the reboot path. However, kexec is clearly not such a case, since we depend on
onlining CPUs, atleast on powerpc.
So re-enable cpu-hotplug after returning from migrate_to_reboot_cpu() in the
kexec path, to fix this regression in kexec on powerpc.
Also, wrap the cpu_up() in powerpc kexec code within a WARN_ON(), so that we
can catch such issues more easily in the future.
Fixes: c97102ba96 (kexec: migrate to reboot cpu)
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With binutils 2.24, various 64 bit builds fail with relocation errors
such as
arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e':
(.text+0x165ee): relocation truncated to fit: R_PPC64_ADDR16_HI
against symbol `interrupt_base_book3e' defined in .text section
in arch/powerpc/kernel/built-in.o
arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e':
(.text+0x16602): relocation truncated to fit: R_PPC64_ADDR16_HI
against symbol `interrupt_end_book3e' defined in .text section
in arch/powerpc/kernel/built-in.o
The assembler maintainer says:
I changed the ABI, something that had to be done but unfortunately
happens to break the booke kernel code. When building up a 64-bit
value with lis, ori, shl, oris, ori or similar sequences, you now
should use @high and @higha in place of @h and @ha. @h and @ha
(and their associated relocs R_PPC64_ADDR16_HI and R_PPC64_ADDR16_HA)
now report overflow if the value is out of 32-bit signed range.
ie. @h and @ha assume you're building a 32-bit value. This is needed
to report out-of-range -mcmodel=medium toc pointer offsets in @toc@h
and @toc@ha expressions, and for consistency I did the same for all
other @h and @ha relocs.
Replacing @h with @high in one strategic location fixes the relocation
errors. This has to be done conditionally since the assembler either
supports @h or @high but not both.
Cc: <stable@vger.kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
<<
Highlights include a few new boards, a device tree binding for CCF
(including backwards-compatible device tree updates to distinguish
incompatible versions), and some fixes.
>>
We get an array of instructions from the hypervisor via device tree that
we write into a buffer that gets executed whenever we want to make an
ePAPR compliant hypercall.
However, the hypervisor passes us these instructions in BE order which
we have to manually convert to LE when we want to run them in LE mode.
With this fixup in place, I can successfully run LE kernels with KVM
PV enabled on PR KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
- BSC9132 is an integrated device that targets Femto base station market.
It combines Power Architecture e500v2 and DSP StarCore SC3850 technologies
with MAPLE-B2F baseband acceleration processing elements
- BSC9132QDS Overview
2Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
SD slot
eTSEC1: Connected to SGMII PHY
eTSEC2: Connected to SGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
P1023RDS is no longer supported/manufactured by Freescale while P1023RDB is.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Besides other potential problems, if MPIC_NO_RESET is not set,
the error interrupt will be masked after it is requested.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for T104x board in board file t104x_qds.c, It is common for
both T1040 and T1042 as they share same QDS board.
T1040QDS board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors (T1040 only)
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types.
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep (T1040 only)
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Add T104xQDS support in Kconfig and Makefile. Also create device tree.
Following features are currently not implmented.
- SerDes: Aurora
- IFC: GASIC, Promjet
- QIXIS
- Ethernet
- DIU
- power supplies management
- ProfiBus
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
processor cores with high-performance data path acceleration architecture
and network peripheral interfaces required for networking & telecommunications.
T1042 personality is a reduced personality of T1040 without Integrated 8-port
Gigabit Ethernet switch.
The T1040/T1042 SoC includes the following function and features:
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration (SEC 5.0)
- RegEx Pattern Matching Acceleration (PME 2.2)
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch (T1040 only)
- Four 1 Gbps Ethernet controllers
- Two RGMII interfaces or one RGMII and one MII interfaces
- High speed peripheral interfaces
- Four PCI Express 2.0 controllers running at up to 5 GHz
- Two SATA controllers supporting 1.5 and 3.0 Gb/s operation
- Upto two QSGMII interface
- Upto six SGMII interface supporting 1000 Mbps
- One SGMII interface supporting upto 2500 Mbps
- Additional peripheral interfaces
- Two USB 2.0 controllers with integrated PHY
- SD/eSDHC/eMMC
- eSPI controller
- Four I2C controllers
- Four UARTs
- Four GPIO controllers
- Integrated flash controller (IFC)
- Change this to LCD/ HDMI interface (DIU) with 12 bit dual data rate
- TDM interface
- Multicore programmable interrupt controller (PIC)
- Two 8-channel DMA engines
- Single source clocking implementation
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Updated the device trees according to the corenet-cf
binding definition.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Updated the device trees according to the corenet-cf
binding definition.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The CoreNet coherency fabric is a fabric-oriented, conectivity
infrastructure that enables the implementation of coherent, multicore
systems. The CCF acts as a central interconnect for cores,
platform-level caches, memory subsystem, peripheral devices and I/O host
bridges in the system.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
[scottwood@freescale.com: formatting and minor changes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This warning can be seen in allyesconfig, and was introduced by commit
f9eb581c63b2acce827570e105205c0789360650 "powerpc: fix build of
epapr_paravirt on 64-bit book3s".
Signed-off-by: Scott Wood <scottwood@freescale.com>
This fixes an allyesconfig build break introduced by commit
7762b1ed7aaee223230793fcee80672e2e3aa7a8 "powerpc: move epapr paravirt
init of power_save to an initcall".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Main changs include:
- Clarified the clock nodes' version number
- Fixed a issue in example
Singed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
some restructuring of epapr paravirt init resulted in
ppc_md.power_save being set, and then overwritten to
NULL during machine_init. This patch splits the
initialization of ppc_md.power_save out into a postcore
init call.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch introduces the support for Keymile's kmcoge4 board which is
the internal reference design for boards based on Freescale's
P2040/P2041 SoCs. This internal reference design is named kmp204x.
The peripherals used on this board are:
- SPI NOR Flash as bootloader medium
- NAND Flash with a ubi partition
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 4 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
CPLD
- 2 I2C busses
- last but not least, the mandatory serial port
The patch also adds a defconfig file for this reference design that is
necessary because of the lowmem option that must be set higher due to
the number of PCIe devices with big ioremapped mem ranges on the boad.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
These are the bindings for 2 MFD devices used on some of the Keymile boards.
The first one is the chassis managmenet bfticu FPGA.
The second one is the board controller (reset, LEDs, GPIOs) QRIO CPDL.
These FPGAs are used in the kmcoge4 board.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Even though the company belongs to Microsemi, many chips are still
labeled as Zarlink. Among them is the family of network clock generators,
the zl3034x.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
PCI controller disable PME message report feature, that shouldn't
have happened. Fix it and enable PME message report feature.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
There are error parameters should be corrected when
calling dma_free_coherent to free rmu rx-ring buffers
in fsl_open_inb_mbox() function.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The only way Freescale booke chips support mappings larger than 4K
is via TLB1. The only way we support (direct) TLB1 entries is via
hugetlb, which is not what map_kernel_page() does when given a large
page size.
Without this, a kernel with CONFIG_SPARSEMEM_VMEMMAP enabled crashes on
boot with messages such as:
PID hash table entries: 4096 (order: 3, 32768 bytes)
Sorting __ex_table...
BUG: Bad page state in process swapper pfn:00a2f
page:8000040000023a48 count:0 mapcount:0 mapping:0000040000ffce48 index:0x40000ffbe50
page flags: 0x40000ffda40(active|arch_1|private|private_2|head|tail|swapcache|mappedtodisk|reclaim|swapbacked|unevictable|mlocked)
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags:
page flags: 0x311840(active|private|private_2|swapcache|unevictable|mlocked)
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.15.0-rc1-00003-g7fa250c #299
Call Trace:
[c00000000098ba20] [c000000000008b3c] .show_stack+0x7c/0x1cc (unreliable)
[c00000000098baf0] [c00000000060aa50] .dump_stack+0x88/0xb4
[c00000000098bb70] [c0000000000c0468] .bad_page+0x144/0x1a0
[c00000000098bc10] [c0000000000c0628] .free_pages_prepare+0x164/0x17c
[c00000000098bcc0] [c0000000000c24cc] .free_hot_cold_page+0x48/0x214
[c00000000098bd60] [c00000000086c318] .free_all_bootmem+0x1fc/0x354
[c00000000098be70] [c00000000085da84] .mem_init+0xac/0xdc
[c00000000098bef0] [c0000000008547b0] .start_kernel+0x21c/0x4d4
[c00000000098bf90] [c000000000000448] .start_here_common+0x20/0x58
Signed-off-by: Scott Wood <scottwood@freescale.com>
A simple patch which was supposed to swap r12 and r11 also
inexplicably changed the offset by two bytes. This instruction
(to load r2) isn't used in LE, so it wasn't noticed.
Fixes: b1ce369e82 ("powerpc: modules: use r12 for stub jump address.)
Reported-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is otherwise a risk of a possible null pointer dereference.
Was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Clear ELF personality flag if ELFv2 is not requested.
The POWER kernel uses a personality flag to determine whether it should
be setting up function descriptors or not (per the updated ABI). This
flag wasn't being cleared on a new process but instead was being
inherited. The visible effect was that an ELFv2 binary could not execve
to an ELFv1 binary.
Signed-off-by: Jeff Bailey <jeffbailey@google.com>
arch/powerpc/include/asm/elf.h | 2 ++
1 file changed, 2 insertions(+)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, on 8641D, which doesn't set CONFIG_HAVE_HW_BREAKPOINT
we get the following splat:
BUG: using smp_processor_id() in preemptible [00000000] code: login/1382
caller is set_breakpoint+0x1c/0xa0
CPU: 0 PID: 1382 Comm: login Not tainted 3.15.0-rc3-00041-g2aafe1a4d451 #1
Call Trace:
[decd5d80] [c0008dc4] show_stack+0x50/0x158 (unreliable)
[decd5dc0] [c03c6fa0] dump_stack+0x7c/0xdc
[decd5de0] [c01f8818] check_preemption_disabled+0xf4/0x104
[decd5e00] [c00086b8] set_breakpoint+0x1c/0xa0
[decd5e10] [c00d4530] flush_old_exec+0x2bc/0x588
[decd5e40] [c011c468] load_elf_binary+0x2ac/0x1164
[decd5ec0] [c00d35f8] search_binary_handler+0xc4/0x1f8
[decd5ef0] [c00d4ee8] do_execve+0x3d8/0x4b8
[decd5f40] [c001185c] ret_from_syscall+0x0/0x38
--- Exception: c01 at 0xfeee554
LR = 0xfeee7d4
The call path in this case is:
flush_thread
--> set_debug_reg_defaults
--> set_breakpoint
--> __get_cpu_var
Since preemption is enabled in the cleanup of flush thread, and
there is no need to disable it, introduce the distinction between
set_breakpoint and __set_breakpoint, leaving only the flush_thread
instance as the current user of set_breakpoint.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
None of the callers check the return value, so it might as
well not have one at all.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The arch/powerpc/include/asm/linkage.h is being unintentionally exported
in the kernel headers since commit e1b5bb6d12 (consolidate
cond_syscall and SYSCALL_ALIAS declarations) when
arch/powerpc/include/uapi/asm/linkage.h was deleted but the header-y not
removed from the Kbuild file. This happens because Makefile.headersinst
still checks the old asm/ directory if the specified header doesn't
exist in the uapi directory.
The asm/linkage.h shouldn't ever have been exported anyway. No other
arch does and it doesn't contain anything useful to userland, so remove
the header-y line from the Kbuild file which triggers the export.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 7f52a526f ("powerpc/eeh: Allow to disable EEH") caused
following build error with "celleb_defconfig" as being catched
by Mikey on linux-next.
arch/powerpc/kernel/eeh.c: In function 'eeh_init_proc':
arch/powerpc/kernel/eeh.c:1173:37: error: 'powerpc_debugfs_root' \
undeclared (first use in this function)
arch/powerpc/kernel/eeh.c:1173:37: note: each undeclared identifier \
is reported only once for each function it appears in
Reported-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge "merge" branch to get two fairly important bug fixes:
powerpc/powernv: Reset root port in firmware
powerpc: irq work racing with timer interrupt can result in timer interrupt
This reverts commit b2b5efcf20.
This code was way too board specific, there are quirks as to how
the PERST line is wired on different boards, we'll have to revisit
this using/creating appropriate firmware interfaces.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I am seeing an issue where a CPU running perf eventually hangs.
Traces show timer interrupts happening every 4 seconds even
when a userspace task is running on the CPU. /proc/timer_list
also shows pending hrtimers have not run in over an hour,
including the scheduler.
Looking closer, decrementers_next_tb is getting set to
0xffffffffffffffff, and at that point we will never take
a timer interrupt again.
In __timer_interrupt() we set decrementers_next_tb to
0xffffffffffffffff and rely on ->event_handler to update it:
*next_tb = ~(u64)0;
if (evt->event_handler)
evt->event_handler(evt);
In this case ->event_handler is hrtimer_interrupt. This will eventually
call back through the clockevents code with the next event to be
programmed:
static int decrementer_set_next_event(unsigned long evt,
struct clock_event_device *dev)
{
/* Don't adjust the decrementer if some irq work is pending */
if (test_irq_work_pending())
return 0;
__get_cpu_var(decrementers_next_tb) = get_tb_or_rtc() + evt;
If irq work came in between these two points, we will return
before updating decrementers_next_tb and we never process a timer
interrupt again.
This looks to have been introduced by 0215f7d8c5 (powerpc: Fix races
with irq_work). Fix it by removing the early exit and relying on
code later on in the function to force an early decrementer:
/* We may have raced with new irq work */
if (test_irq_work_pending())
set_dec(1);
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Resetting root port has more stuff to do than that for PCIe switch
ports and we should have resetting root port done in firmware instead
of the kernel itself. The problem was introduced by commit 5b2e198e
("powerpc/powernv: Rework EEH reset").
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several of the error paths from fsl_rio_setup are missing error
messages.
Worse, fsl_rio_setup initializes several global pointers and does not
NULL them out after freeing/unmapping on error. This caused
fsl_rio_mcheck_exception() to crash when accessing rio_regs_win which
was non-NULL but had been unmapped.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Liu Gang <Gang.Liu@freescale.com>
---
Liu Gang, are you sure all of these error conditions are fatal? Why
does the rio driver fail if rmu is not present (e.g. on t4240)?
This series adds support for building the powerpc 64-bit
LE kernel using the new ABI v2. We already supported
running ABI v2 userspace programs but this adds support
for building the kernel itself using the new ABI.
In case of extending the eaddr in future, use this macro
PGTABLE_EADDR_SIZE to ease the maintenance of the code.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds an option to enable a work around for an icache bug on
476 that can cause execution of stale instructions when falling
through pages (IBM errata #46). It requires a recent version of
binutils which supports the --ppc476-workaround option.
The work around enables the appropriate linker options and ensures
that all module output sections are aligned to 4K page boundaries. The
work around is only required when building modules.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PPC476GTR SoC supports message signalled interrupts (MSI) by writing
to special addresses within the High Speed Transfer Assist (HSTA) module.
This patch adds support for PCI MSI with a new system device. The DMA
window is also updated to allow access to the entire 42-bit address range
to allow PCI devices write access to the HSTA module.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the IBM Akebono board.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The IBM Akebono code uses the same initialisation functions as the
earlier Currituck board. Rather than create a copy of this code for
Akebono we will instead integrate support for it into the same file as
the Currituck code.
This patch just renames the board support file and updates the Makefile.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we never get around to seeing an HEA ethernet adapter, there's
no point in restricting ourselves to 4k IO page size.
This speeds up IO maps when CONFIG_IBMEBUS is disabled.
[ Updated the test to also lift the restriction on arch 2.07
(Power 8) which cannot have an HEA
-- BenH ]
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
foo
Unaligned stores take alignment exceptions on POWER7 running in little-endian.
This is a dumb little-endian base memcpy that prevents unaligned stores.
Once booted the feature fixup code switches over to the VMX copy loops
(which are already endian safe).
The question is what we do before that switch over. The base 64bit
memcpy takes alignment exceptions on POWER7 so we can't use it as is.
Fixing the causes of alignment exception would slow it down, because
we'd need to ensure all loads and stores are aligned either through
rotate tricks or bytewise loads and stores. Either would be bad for
all other 64bit platforms.
[ I simplified the loop a bit - Anton ]
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we do a treclaim and we are not in TM suspend mode, it results in a TM bad
thing (ie. a 0x700 program check). Similarly if we do a trechkpt and we have
an active transaction or TEXASR Failure Summary (FS) is not set, we also take a
TM bad thing.
This should never happen, but if it does (ie. a kernel bug), the cause is
almost impossible to debug as the GPR state is mostly userspace and hence we
don't get a call chain.
This adds some checks in these cases case a BUG_ON() (in asm) in case we ever
hit these cases. It moves the register saving around to preserve r1 till later
also.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We save r1 to the scratch SPR and restore it from there after the trechkpt so
saving r1 to the paca is not needed.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>