A crash upon booting that is caused by bcm43xx has been reported [1] and
found to be due to a work queue being reinitialized while work on that
queue is still pending. This fix modifies the shutdown of work queues and
prevents periodic work from being requeued during shutdown. With this patch,
no more crashes on reboot were observed by the original reporter. I do not
get that particular failure on my system; however, when running a large
number of ifdown/ifup sequences, my system would kernel panic with the
'caps lock' light blinking at roughly a 1 Hz rate. In addition, there were
infrequent failures in the firmware that resulted in 'IRQ READY TIMEOUT'
errors. With this patch, no more of the first type of failure occur, and
incidence of the second type is greatly reduced.
[1] http://bugzilla.kernel.org/show_bug.cgi?id=8937
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch solves a problem that the spidernet driver sometimes fails
to handle IRQ.
The problem happens because,
- In Cell architecture, interrupts may arrive at an interrupt
controller, even if they are masked by the setting on registers of
devices. It happens when interrupt packets are sent just before
the interrupts are masked.
- spidernet interrupt handler compares interrupt reasons with
interrupt masks, so when such interrupts occurs, spidernet interrupt
handler returns IRQ_NONE.
- When all of interrupt handler return IRQ_NONE, linux kernel disables
the IRQ and it no longer delivers interrupts to the interrupt handlers.
spidernet doesn't work after above sequence, because it can't receive
interrupts.
This patch changes spidernet interrupt handler that it compares
interrupt reason with SPIDER_NET_INTX_MASK_VALUE.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update last_rx in registered device struct instead of
in the dummy device.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduces a module parameter to decide whether the physical
port link state is propagated to the network stack or not.
It makes sense not to take the physical port state into account
on machines with more logical partitions that communicate
with each other. This is always possible no matter what the physical
port state is. Thus eHEA can be considered as a switch there.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Lock debugging finds a problem in phy.c and phy_device.c,
this patch fixes it. Tested on an AT91SAM9263-EK board,
kernel 2.6.23-rc4.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to restore multicast settings on resume and after 'ethtool -r'.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
64-bit DMA causes data corruption with atl1. We don't know why, and Atheros
is working on it. For now, just use 32-bit DMA. This is a big hack that is
probably wrong, but it stops the bleeding.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <csnook@redhat.com>
Acked-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A hardware bug was revealed after a recent PCI MSI patch was made to
always disable legacy INTX when enabling MSI. The 5714/5780 chips
will not generate MSI when INTX is disabled, causing MSI failure
messages to be reported, and another patch was made to workaround the
problem by disabling MSI on ServerWorks HT1000 bridge chips commonly
found with the 5714.
We workaround this chip bug by enabling INTX after we enable MSI and
after we resume from suspend.
Update version to 3.81.
This problem was discovered by David Miller.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
- cxgb3 engine microcode load
cxgb3 - Fix dev->priv usage
qeth: Drop ARP packages on HiperSockets interface with NOARP attribute.
qeth: provide specific message for OSA-adapters exclusively used
qeth: crash during reboot after failing online setting
qeth: Announce tx checksumming for qeth devices in TSO/EDDP mode
qeth: dont return the return values of void functions.
qeth: enforce a rate limit for inbound scatter gather messages
qeth: ungrouping a device must not be interruptible
netxen: fix crashes during module unload
netxen: Avoid firmware load in PCI probe
PS3: fix the bug that 'ifconfig down' would hang
IOC3: Program UART predividers.
Load the engine microcode when an interface
is brought up, instead of of doing it when the module
is loaded.
Loosen up tight binding between the driver and the
engine microcode version.
There is no need for microcode update with T3A boards.
Fix the file naming.
Do a better job at logging the loading activity.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
cxgb3 used netdev_priv() and dev->priv for different purposes.
In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix.
This patch is a partial backport of Dave Miller's changes in the
net-2.6.24 git branch.
Without this fix, cxgb3 crashes on 2.6.23.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes two problems during driver unload. The pci_disable_device()
call is before firmware reload, causing reads and writes across PCI bus after
disabling device. Second problem is the register window was wrong during
firmware reload
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Loading firmware during PCI probe can lead to incorrect initialization,
rendering the card unusable until next reboot. This was introduced a while
ago as a workaround for firmware bug, a better workaround was submitted for
this a while ago. So removing original hack that loads firmware during probe.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the bug that 'ifconfig eth0 down' would hang up, reported by Stefan
Assmann <sassmann@suse.de>.
As we removed netif_poll_enable() from dev->open(), we should not use
netif_poll_disable() in dev->stop().
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The IOC3 driver's UART detection bits used to rely on the the firmware
setting the UART pre-divider in a way that's apropriate for the 8250
driver which doesn't currently program this register. This happens
to work for the console but not rarely for additional ports.
While at it, also program the UART to RS-232 PIO mode; it the UART might
have been in mac-serial and/or DMA mode though that hasn't actually been
observed in practice.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add comment to explain why we cannot read back after chip reset
before delaying.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2.c (incorrectly) sets current->state directly to
TASK_UNINTERRUPTIBLE, without going through set_task_state(). However
all the code wants to do is an msleep so just make it do that instead...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The general kernel memory allocation functions return void pointers
and there is no need to cast their return values.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc() returns a void pointer, so there is no need to cast it in
drivers/net/irda/kingsun-sir.c::kingsun_probe().
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function declared static in forward declaration, but not in actual code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
More noodlin on long flights, patch bin. Sparse warning fix for eql.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch from Peter Oruba, convert myri10ge to use pcie_get_readrq()
and pcie_set_readrq() instead of our own PCI calls and arithmetics.
These driver changes incorporate the proposed PCI-X / PCI-Express read byte
count interface. Reading and setting those values doesn't take place
"manually", instead wrapping functions are called to allow quirks for some
PCI bridges.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off by: Peter Oruba <peter.oruba@amd.com>
Based on work by Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Includes hcp_epas_dtor in eq/cq/qp destructors to unmap
HW register.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the module parameter description of "use_mcs" to
show correct default value
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Userspace DLPAR tool expects decimal numbers to be written to
and read from sysfs entries.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver remove method needs to return an int not void. This was just
never noticed because usually this driver is not being built as a module.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark new version to track if current driver is in use.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes the extra timer overhead that people were whining about
as a 2.6.23 regression.
Running the watchdog timer all the time is unneeded. Change it
to run only if link is up, and reduce frequency to save power.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure PCI register for PHY power gets cleared on boot, and make
sure to avoid any PCI posting problems.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When transferring data at full speed, the DM9000 network interface
sometimes stops sending/receiving data. Worse, ksoftirqd consumes
100% cpu and the net tx watchdog never triggers.
Fix by spin_lock_irqsave() in dm9000_start_xmit() to prevent the
interrupt handler from interfering.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Writing BMCR_RESET bit will reset MII_BMCR to default values. This is
clearly not what we want.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IP32 doesn't even have a ZONE_DMA so no point in using GFP_DMA in any
IP32-specific device driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As noticed by Chuck Ebbert, commit c5e3ae8823
introduced a copy-paste typo, as realtek phy is 0x732 and not 0x1c1. Obvious
fix below suggested by Ayaz Abdulla.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch addresses the issue with "osize too small" errors in mppe
encryption. The patch fixes the issue with wrong output buffer size
being passed to ppp decompression routine.
--------------------
As pointed out by Suresh Mahalingam, the issue addressed by
ppp-fix-osize-too-small-errors-when-decoding patch is not fully resolved yet.
The size of allocated output buffer is correct, however it size passed to
ppp->rcomp->decompress in ppp_generic.c if wrong. The patch fixes that.
--------------------
Signed-off-by: Konstantin Sharlaimov <konstantin.sharlaimov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are special PHY settings available on Yukon EC-U chip that
should not get cleared. This should solve mysterious errors on some
motherboards (like Gigabyte DS-3).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the forcedeth driver receives too much work in an interrupt, it
assumes it has a broken hardware with stuck IRQ. It works around the
problem by disabling interrupts on the nic but makes a printk while
holding device spinlog - which isn't smart thing to do if you have
netconsole on the same nic.
This patch moves the printk's out of the spinlock protected area.
Without this patch the machine hangs hard. With this patch everything
still works even when there is significant increase on CPU usage while
using the nic.
Signed-off-by: Timo Jantunen <jeti@iki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Incorrect semicolon after if statement
mlx4_core: Wait 1 second after reset before accessing device
IPoIB: Fix leak in ipoib_transport_dev_init() error path
IB/mlx4: Fix opcode returned in RDMA read completion
IB/srp: Add OUI for new Cisco targets
IB/srp: Wrap OUI checking for workarounds in helper functions
RDMA/cxgb3: Always call low level send function via cxgb3_ofld_send()
IB: Move the macro IB_UMEM_MAX_PAGE_CHUNK() to umem.c
IB: Include <linux/list.h> and <linux/rwsem.h> from <rdma/ib_verbs.h>
IB: Include <linux/list.h> from <rdma/ib_mad.h>
IB/mad: Fix address handle leak in mad_rmpp
IB/mad: agent_send_response() should be void
IB/mad: Fix memory leak in switch handling in ib_mad_recv_done_handler()
IB/mad: Fix error path if response alloc fails in ib_mad_recv_done_handler()
IB/sa: Don't need to check for default P_Key twice
IB/core: Ignore membership bit in ib_find_pkey()
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPVS]: Use IP_VS_WAIT_WHILE when encessary.
[NET]: Share correct feature code between bridging and bonding
[ATM] drivers/atm/iphase.c: mostly kmalloc + memset conversion to kzalloc
[IRDA] irda-usb.c: mostly kmalloc + memset conversion to k[cz]alloc
[WAN] drivers/net/wan/hdlc_fr.c: kmalloc + memset conversion to kzalloc
[DCCP]: fix memory leak and clean up style - dccp_feat_empty_confirm()
[DCCP]: fix theoretical ccids_{read,write}_lock() race
[XFRM]: Clean up duplicate includes in net/xfrm/
[TIPC]: Clean up duplicate includes in net/tipc/
[SUNRPC]: Clean up duplicate includes in net/sunrpc/
[PKT_SCHED]: Clean up duplicate includes in net/sched/
[IPV6]: Clean up duplicate includes in net/ipv6/
[IPV4]: Clean up duplicate includes in net/ipv4/
[ATM]: Clean up duplicate includes in net/atm/
[ATM]: Clean up duplicate includes in drivers/atm/
[IPCONFIG]: ip_auto_config fix
[ATM]: fore200e_param_bs_queue() must be __devinit
This patch adds support for 2 new board variants:
- A Quad port fiber 82571 board
- A blade version of the 82571 quad copper board
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
http://bugzilla.kernel.org/show_bug.cgi?id=8797 shows that the
bonding driver may produce bogus combinations of the checksum
flags and SG/TSO.
For example, if you bond devices with NETIF_F_HW_CSUM and
NETIF_F_IP_CSUM you'll end up with a bonding device that
has neither flag set. If both have TSO then this produces
an illegal combination.
The bridge device on the other hand has the correct code to
deal with this.
In fact, the same code can be used for both. So this patch
moves that logic into net/core/dev.c and uses it for both
bonding and bridging.
In the process I've made small adjustments such as only
setting GSO_ROBUST if at least one constituent device
supports it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
xennet_tx_bug_gc can free the skb before we use it, so make sure we don't.
Signed-off-by: Keir Fraser <keir@xensource.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A special sequence of ifconfig up/down and plug/unplug the cable can break
the duplex configuration of the driver.
Setting
vp->mii.full_duplex = vp->full_duplex
in vortex_up should fix this.
Addresses Bug 8575 3c59x duplex configuration broken
http://bugzilla.kernel.org/show_bug.cgi?id=8575
Cc: Martin Buck <mb-tmp-ohtmvyyn.xreary.bet@gromit.dyndns.org>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When a detailed netdev error is counted, we also must account for it in the
aggregated error count.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8106
Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Chongfeng Hu <loveminix@yahoo.com.cn>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/ax88796.c: In function `ax_probe':
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 4)
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 5)
resource_size_t isn't size_t.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the pause counter to avoid a needless device reset, and
print a message telling the admin that our link partner is
flow controlling us down to 0 pkts/sec.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to disable the rx_copybreak feature on hardware architectures that
don't allow unaligned DMA access.
#ifdef code taken from tulip_core.c. Problem pointed out by Ivan
Kokshaysky.
Signed-off-by: Dustin Marquess <jailbird@alcatraz.fdf.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Put a 1000 msec delay after resetting the device before attempting to
do config cycles on it. Not waiting causes system hangs on some
chipsets, e.g. Intel E7520, when the driver is loaded.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
> >> Looks like memset() is zeroing wrong nr of bytes.
> >
> > Good catch, however, I think we can just remove this memset altogether
> > since the memory gets allocated via kzalloc.
>
> Correct, that memset() is superfluous.
Ok. Then this should do it.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
drivers/net/ibmveth.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use shorter method to determine whether adapter has configured ports
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sis190 driver assumes to find ISA only on SiS965.
similar fix is in sis900 driver, see bug report
http://bugs.debian.org/435547
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
use the simpler spin_trylock_irqsave() API to get the adapter lock.
[ this is also a fix for -rt where adapter->lock is a sleeping lock. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SH boards in general only wire this up in 8 or 16-bit mode, and
as we never had the wrappers for 32-bit mode defined, SMC_CAN_USE_32BIT
caused build failure for the non-Solution Engine boards. This gets it
building again.
Also kill off the straggling set_irq_type() definition, this is left
over cruft that was missed when the rest of it switched to IRQ flags.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
--
drivers/net/smc91x.h | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Theory : though needless, it should not have hurt.
Practice: it does not play nice with DEBUG_SHIRQ + LOCKDEP + UP
(see https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242572).
The patch makes sense in itself but I should dig why it has an effect
on #242572 (assuming that NAPI do not change in a near future).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Fix extracted from Realtek's driver (8.002.00/20070713) for the PHY
attached to 8111/8168b chipsets.
The check against mac_version is just usual paranoia during the bugfix
period of the kernel cycle. -- FR
Tested on Asus M2A-VM motherboard by Roger So.
No regression on my Asrock 945G DVI either (built-in 8168 + 2x8169).
Signed-off-by: Roger So <roger.so@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
While filling the control set the driver tests for a PSPOLL frame.
But it tested only the subtype of the packet. The full type needs
to be tested to identify those packets reliably.
[dsd@gentoo.org: backport to mainline]
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
conf->mac_addr is not guaranteed to be set. This ensures priv->hwaddr is
always set to a valid mac address. Thanks to Johannes Berg
<johannes@sipsolutions.net> for finding this problem.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 77548f5807.
David Woodhouse wrote:
>This broke my shinybook. I seem to get absolutely _no_ outgoing packets,
>although I can receive OK.
Larry Finger wrote:
>Please revert this patch.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device would not resume properly if it was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
bnx2_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
bnx2_suspend() and bnx2_resume() regardless of netif_running() state.
Update version to 1.6.4.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joachim Deguara <joachim.deguara@amd.com> reported that tg3 devices
would not resume properly if the device was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
tg3_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
tg3_suspend() and tg3_resume() regardless of netif_running() state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* wrong argument passed to pci_unmap_single() on failure
exit paths
* leak in the same area
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is needed because commit 313674afa8
inlines the generic function to the caller.
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: Li Yang <leoli@freescale.com>
This fix section mismatch:
reference to .exit.text:uec_mdio_exit (between 'ucc_geth_init' and 'uec_mdio_init')
void __exit uec_mdio_exit(void) is called from
- static int __init ucc_geth_init(void)
- static void __exit ucc_geth_exit(void)
First one would make error path more than just an error.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Li Yang <leoli@freescale.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
[RTNETLINK]: Fix warning for !CONFIG_KMOD
[IPV4] ip_options.c: kmalloc + memset conversion to kzalloc
[DECNET]: kmalloc + memset conversion to kzalloc
[NET]: ethtool_perm_addr only has one implementation
[NET]: ethtool ops are the only way
[PPPOE]: Improve hashing function in hash_item().
[XFRM]: State selection update to use inner addresses.
[IPSEC]: Ensure that state inner family is set
[TCP]: Bidir flow must not disregard SACK blocks for lost marking
[TCP]: Fix ratehalving with bidirectional flows
[PPPOL2TP]: Add CONFIG_INET Kconfig dependency.
[NET]: Page offsets and lengths need to be __u32.
[AF_UNIX]: Make code static.
[NETFILTER]: Make nf_ct_ipv6_skip_exthdr() static.
[PKTGEN]: make get_ipsec_sa() static and non-inline
[PPPoE]: move lock_sock() in pppoe_sendmsg() to the right location
[PPPoX/E]: return ENOTTY on unknown ioctl requests
[IPV6]: ipv6_addr_type() doesn't know about RFC4193 addresses.
[NET]: Fix prio_tune() handling of root qdisc.
[NET]: Fix sch_api to properly set sch->parent on the root.
...
One patch for two trivial typos of 'error' with three R's, appearing in message strings.
There's a bunch more of the same in comments, not dealt with here.
Signed-off-by: Eddy L O Jansson <eddy@klopper.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rcu_dereference() primitive needs to be applied to an l-value in order to
ensure that compiler writers don't get an opportunity to apply reordering
optimizations that could result in multiple fetches or in other misbehavior.
This patch pulls the rcu_dereference() calls in bpq_seq_next() up to the point
at which the fetched pointers are still l-values, rather than after
list_entry() has transformed them into r-values.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the transition to the ethtool_ops way of doing things, we supported
calling the device's ->do_ioctl method to allow unconverted drivers to
continue working. Those days are long behind us, all in-tree drivers
use the ethtool_ops way, and so we no longer need to support this.
The bonding driver is the biggest beneficiary of this; it no longer
needs to call ioctl() as a fallback if ethtool_ops aren't supported.
Also put a proper copyright statement on ethtool.c.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new code produces the same results as the old version and is
~ 3 to 6 times faster for 4-bit hashes on the CPUs I tested.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPPOL2TP uses UDP so it obviously depends on CONFIG_INET.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
and the last one for now: Acquire the sock lock in pppoe_sendmsg()
before accessing the sock - and in particular avoid releasing the lock
even though it hasn't been acquired.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
here another patch for the PPPoX/E code that makes sure that ENOTTY is
returned for unknown ioctl requests rather than 0 (and removes another
unneeded initializer which I didn't bother creating a separate patch for).
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because IPv4 and IPv6 both depend on the presence of the loopback
device to function, failure in registration the loopback device should
be fatal.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was still using the deprecated prom_*() interfaces to
obtain values out of the OBP device tree, and this is causing
some kinds of problems on sparc32 especially SMP boxes.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
Fix a potential NULL pointer dereference in mace_interrupt() in drivers/net/pcmcia/nmclan_cs.c
PATCH kernel 2.6.22] PCMCIA-NETDEV : modify smc91c92_cs.c to become SMP safe
S2io: Increment received packet count correctly
S2io: Fix crash when resetting adapter
S2io: Mask spurious interrupts
S2IO: Implementing review comments from old patches
S2IO: Checking for the return value of pci map function
S2IO: Removing MSI support from driver
S2IO: Removing 3 buffer mode support from the driver
netxen: drop redudant spinlock
netxen: Fix interrupt handling for multiport adapters
netxen: re-init station address after h/w init
tulip: Remove tulip maintainer
forcedeth: mac address correct
gfar: Fix modpost warning
lib8390: comment on locking by Alan Cox
Fix a potential NULL pointer dereference in write_bulk_callback() in drivers/net/usb/pegasus.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: Workaround problem of errormask register being overwritten
IB/ipath: Fix some issues with buffer cancel and sendctrl register update
IB/ipath: Use faster put_tid_2 routine after initialization
IB/ipath: Remove unsafe fastrcvint code from interrupt handler
IB/ehca: Move extern declarations from .c files to .h files
IB/mlx4: Whitespace fix
IB/ehca: Fix include order to better match kernel style
mlx4_core: Remove kfree() in mlx4_mr_alloc() error flow
RDMA/amso1100: Initialize the wait_queue_head_t in the c2_qp structure
This patch fixes a potential null dereference bug where we dereference
DEV before a null check. This patch simply moves the dereferencing after
the null check.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
protect smc_start_xmit, smc_interrupt and media_check by spin_lock.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Fix to increment the received packet count correctly.
(Resending; Removed HTML sections in the patch)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Removed the call to pci_set_power_state to reset the adapter as it was resulting
in system crash on some platforms.
(Resending; Removed HTML sections in the patch)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Mask single and double bit ETQ ecc errors to inhibit spurious interrupts.
(Resending; Removed HTML sections in the patch)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Checking for the return value of pci map function
- Implemented Francois Romieu's comments on eliminating code duplication
using goto
- Implemented Francois Romieu's comments on using a temporary variable for
accessing statistics structure
Signed-off-by: Veena Parat <veena.parat@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Removed 3 buffer mode support from driver - unused feature
- Incorporated Jeff Garzik's comments on elimination of inline typecasting
- Code cleanup : Removed a few extra spaces
Signed-off-by: Veena Parat <veena.parat@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some leftover code that makes use of adapter->lock in tx_timeout function,
which resets the interface under this lock. In close() when the workqueue
is flushed, prints the warning about sleeping with interrupts disabled
(when spinlock debug is enabled). The lock was required with private netxen
IOCTLs, which were removed a while ago.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes masking of interrupts on multiport adapters. Also disables
interrupts upon ifdown interface. The wrong mask could result in interrupt
flood after interface is down.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for firmware bug with 2nd port of multiport adapter,
where MAC address is reset. Driver just needs to overwrite it with the
value read from PROM.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In older chipsets, the mac address was stored in reversed order.
However, in newer chipsets, the mac address is in correct order. This
patch takes those newer chipsets into account and does not rely on a
special bit setup by BIOS'.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the following modpost warning:
WARNING: vmlinux.o(.init.text+0x1aa6c): Section mismatch: reference to .exit.text:gfar_mdio_exit (between 'gfar_init' and 'gfar_mdio_init')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Additional explanation of problems with locking by Alan Cox.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a potential null dereference bug where we dereference
pegasus before a null check. This patch simply moves the dereferencing
after the null check.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Added code to recognize the second interface on M5275 boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the MCF5272, there is no need to read the ICR before writing it :
the bit 4n+3 is a write-enable for the bits 4n,4n+1 and 4n+2.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the work queue code in the FEC driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed unused CONFIG symbol and its conditional code from FEC driver.
Pointed out by Robert P. J. Day <rpjday@mindspring.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include cacheflush.h to get definitions for cache functions used
in this code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gabriel C reports lguest doesn't compile with CONFIG_BLOCK=n. Fix this
by introducing a config var for the block device, which depends on
LGUEST && BLOCK. Do the same for the net driver, rather then depending
gratuitously on CONFIG_NET.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Input Serio: Blackfin doesnt support I8042 - make sure it doesnt get selected
Blackfin arch: add BF54x I2C/TWI TWI0 driver support
Blackfin On-Chip RTC driver update for supporting BF54x
Blackfin Ethernet MAC driver: fix bug Report returned -ENOMEM upwards (in case L1/uncached memory alloc fails)
Blackfin arch: add error message when IRQ no available
Blackfin arch: Initialize the exception vectors early in the boot process
Blackfin arch: fix a compiling warning about dma-mapping
Blackfin arch: switch to using proper defines this time THREAD_SIZE and PAGE_SIZE instead of just PAGE_SIZE everywhere
Blackfin arch: fix bug which unaligns the init thread's stack and causes the current macro to fail.
Blackfin arch: Load P0 before storing through it
Blackfin arch: fix KGDB bug, dont forget last parameter.
Blackfin arch: add selections for BF544 and BF542
Blackfin arch: use bfin_read_SWRST() now that BF561 provides it
Blackfin arch: setup aliases for some core Core A MMRs
mlx4_mr_alloc() doesn't actually allocate mr (it just initializes the
pointer that the caller passes in), so it shouldn't free it if an
error occurs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change INT0 trigger mode from edge-sense mode to level-sense mode,
in order to fix the following timeout error:
'NETDEV WATCHDOG: eth0: transmit timed out'.
This patch is required only for the Mappi platform.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation: The FIXMEs
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation: The Drivers
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Address of auto variable is not a userland pointer. A good thing, too,
since if pppol2tp_tunnel_getsockopt() would _really_ get a userland pointer
as argument, it would be an instant roothole...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
netdev: i82596 Ethernet needs <asm/cacheflush.h> on m68k
drivers/net/82596.c: In function 'init_rx_bufs':
drivers/net/82596.c:552: error: implicit declaration of function 'cache_clear'
drivers/net/82596.c: In function 'i596_start_xmit':
drivers/net/82596.c:1104: error: implicit declaration of function 'cache_push'
The driver still compiles on ia32 (CONFIG_APRICOT=y)
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains new device settings for MCP73 chipset.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sparse (correctly) thinks this function should be static. Make it so.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker noted that we've already dereferenced "dev" when we
check whether it's NULL.
Since it's impossible that "dev" is NULL at this place this patch
removes the NULL check.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a change to remove a local hack in favour to __maybe_unused that
has been recently added.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
phy_read() returns a negative number if there's an error, but the
error-checking code in the Vitesse driver's config_intr function
triggers if phy_read() returns non-zero. Correct that.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reduced allocation size for rx skb buffers, from 2308 bytes to
1356 per buffer.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use constants already provided by the kernel for ethernet related lengths.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the threshold number of descriptors used to trigger CMB writes.
The vendor reports that under certain conditions this will reduce the
number of unnecessary tx interrupts and improve rx performance.
This change is lifted directly from vendor version 1.2.40.2 of the L1
driver.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DMA engine setup contains a typo that can result in an incorrect
dmaw_block setting.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed rare issue that 'lv1_net_start_rx_dma failed, status=-9" was shown
in dmesg. This meant restarting rx DMA had been rejected by the hypervisor.
This issue would caused if the guest os requested starting DMA when
the hypervisor thought the DMA was in progress.
The state machine for DMA status of the hypervisor would be updated
by processing interrupt in the hypervisor.
Thus we should wait for the interrupt delivery before restarting
DMA.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removed use of netif_poll_enable() in open function.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use net_device name for registration of irq as many network drivers do.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removed the statistics information from private structre.
Instead, use net_device_stats in net_device structure.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
gelic: TX descriptor handling cleanup
- Emitted return value of NETDEV_TX_LOCKED when DMA map or kick
failure.
Now it would free the skb, update drop packet statistics
and return OK. Requested from Jeff Garzik.
- Enable tx queue if number of free descriptors are more than 2
- Fixed descriptor leak if dma map for second descriptor failed
- Stopped calling xmit handler from interrupt handler in order
to recheck tx queue. Instead, call appropriate helper functions.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Removed the embarrassing definition which was used in only one
place.
- Fixed wrong initialization of dmac_cmd_status.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed the bug that calculation of the address of rx descriptor was
wrong.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The firmware should be loaded after resetting hardware during PCI probe,
besides module unload. This fixes issue with 2nd port of multiport adapter
on powerpc blades. This patch also fixes a bug that PCI resources are not
freed if dma watchdog shutdown failed. The dma watchdog poll messages
during module unload are also suppressed.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adds netif message level control to the ucc_geth driver. The level can
be set by module parameter and ethtool.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch enables statistics in ucc_geth and adds ethtool support to
ucc_geth driver.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Support small QP queues
IB/ehca: Make internal_create/destroy_qp() static
IB/ehca: Move ehca2ib_return_code() out of line
IB/ehca: Generate async event when SRQ limit reached
IB/ehca: Support large page MRs
IB/mlx4: Fix error path in create_qp_common()
mlx4_core: Change command token on timeout
IB/mthca: Change command token on timeout
IB/ipath: Remove ipath_layer dead code
IB/mlx4: Fix leaks in __mlx4_ib_modify_qp
Enabling drivers from "Devices > Networking" (in menuconfig), for
example SLIP and/or PLIP, throws link time errors when CONFIG_NET itself
is =n. Have CONFIG_NETDEVICES depend on CONFIG_NET.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EP7211 SIR driver was the only one left without a new SIR API port.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Garzik